Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Transportation Laboratories to perform their Transportation Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Transportation laboratory that would like more information on these Transportation projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Chemical toxicology laboratory needed for two in vivo OECD toxicity studies of consumer air deodorizer and disinfectant supplied in Tyvek pouch. Studies must be performed to OECD 403 Acute Inhalation Toxicity of Chemicals in rodent models and OECD 402 Acute Dermal Toxicity of Chemicals in rodent models. Studies are being performed to support changes to the DOT 6.1 classification under transportation restrictions.
Automotive parts manufacturers needs laboratory for accelerated againg of test oil sa including GC-MS headspace and GC-MS direct injection (after dilution by dichloromethane) 2 test oil sa) 0 days and after 7 days heat agingb) 0 days and after 7 days heat aging and 21 days heat aging
Construction laboratory needed for materials and toxicity testing of naval thermal insulation testing to various standards including: NCD 1427 : SPECIFICATION FOR MINERAL WOOL MARINE BOARD FOR THERMAL AND ACOUSTIC INSULATION ON BOARD INDIAN NAVAL SHIPS
NCD 1433 : SPECIFICATIONS FOR ELASTOMERIC NITRILE THERMAL INSULATION FOR USE ONBOARD INDIAN NAVAL SHIPS
Electrical laboratory needed for SAE compliance testing of optical warning devices used on authorized emergency, maintenance, and service vehicles to SAE J845 Class 1 . Recommended practice providing design guidelines, test procedures, and performance requirements for 360 degree optical warning devices and selective coverage defined as any light that provides greater coverage then 40 degrees left-to-right but less than 360 degrees. Intended for authorized emergency, maintenance and service vehicles. Lighting tested from 5 degrees upward to 5 degrees downward.
Environmental Simulation Laboratory needed for paint plastic cans testing for 28 days at stacked conditions to simulate summer test simulation at day time 45 to 48 degree c, night time 29 to 35 degree c ? What tests are we going to perform on cans (summer test simulation) The test mentioned below should be carried out. o Leak o Drop o Roll o Transportation o Deflection o Opening and closing of Lid ? Tinting and shaking
Laboratory needed for transportation test for the new packaging box according to ASTM D4169-09 as per below: Please help to quote the test as below, Distribution Cycle 13, Assurance Level III. Test sequence as below: 1. Temperature and Humidity Conditioning 2. Schedule A: Handling 3. Schedule C: Vehicle Stacking 4. Schedule F: Loose-load vibration 5. Schedule I: Low Pressure 6. Schedule E: Vehicle Vibration 7. Schedule J: Concentrated Impact 8. Schedule A: Handling
Shipping company needs laboratory for hose bend testing of 6 hoses that need doing bending test according to EN1765 standard. Electrically discontinuous Hydrostatic tested, Vacuum tested. Oil Suction and Discharge Hose hose id:12 ID x 30' OAL working pressure Meets BS1435 EN1765,type S15 standard 150# RF Weld Neck Flange on end 1 and 150# lap Joint Floating Flange on end 2 assembly weight:1130 LBS
Packaging Laboratory needed for vibration testing an automotive pallet load to ensure returnable packaging will hold up pack ships for automotive manufacturing industry. size of pallet load 48x45x53h total weight 1050lbs 4 layers per pallet load will the bottom layer hold up
Laboratory needed for validation testing projects on Locomotive Radiators and CACs.
1. Thermal Cycling: Full size radiator testing, which is approximately 1000 Kg. Low and high temperature water will be required at 98 degree C and at 4 degree C. Air at high pressure shall be applied above the water. Cycles are 250000.
2. Pressure Cycling: Full size radiator testing, which is approximately 1000 Kg. low and high temperature liquid will be used. High pressure air will be required at 60 psi with cycles of 250000.
3. Shaker Table: Full size radiator testing. Water will be required to circulate at 40 psig pressure.
4. Highly Accelerated Life Test: This is the process of testing product by subjecting stress, strain, temperature, pressure etc.. in excess of its normal service parameters to uncover the faults and potential mod
Packaging laboratory needed for ASTM transportation testing for the new medical device packaging box according to ASTM D4169-09 as per below: Please help to quote the test as below, Distribution Cycle 13, Assurance Level III. Test sequence as below: 1. Temperature and Humidity Conditioning 2. Schedule A: Handling 3. Schedule C: Vehicle Stacking 4. Schedule F: Loose-load vibration 5. Schedule I: Low Pressure 6. Schedule E: Vehicle Vibration 7. Schedule J: Concentrated Impact 8. Schedule A: Handling
Shipping vessel owner needs Spain laboratory for bunkered fuel analysis ?Asphaltenes, Ash, Carbon Residue ?Density, Flashpoint ?Sulfur Content, Hydrogen Sulfide ?Microbes Contamination ?Pour Point, Stability ?Total Sediment Potential (TSP) ?Viscosity, Water Content ?ISO 8217 Bunker Fuel Testing ?H2S Testing for Bunker Fuels ?Bunker Fuel Chemical Contamination Screening ?Chlorinated Compound Contamination of Bunker Fuel
Laboratory needed for DOT Jerrican (2.2-gallon portable fuel container) Testing per Department of Transportation (DOT) ?Subpart M: Testing of Non-Bulk Packaging and Packages CFR / I / C / 178 ? Specification of Packages, Sections 178.603, 178.604, 178.605, 178.606, 178.608 and 178.609
Mechanical Laboratory needed for industrial spring testing: KLT tests (Key Life Tests) for transportation springs according to company specified operations for performance as per our document. We look forward to hear your feedback.
Canada Laboratory needed for HDPE Plastic Pipe Testing to American Association of State Highway and Transportation Officials, AASHTO designations: M252 and M294 Plastic Pipes (HDPE) All tests needed
Materials laboratory needed that is capable of running Alberta Transportation Specification B388 tests for type 3 concrete sealers
URGENT: USA FDA GMP Medical device laboratory needed for device functionality and performance testing of medial devices used to administer biological drugs intra-parentally to humans. These devices include auto-injectors, pre-filled syringes, etc. Testing includes break loose/glide force testing, flow testing, simulating transportation and drop testing, etc.
Large transportation company needs physical laboratory for Thermal cycle testing for water charge air coolers with below test requirements. Requirements are the following: There are 3 stages of thermal cycle testing (TC). Stage 1, stage 2 and stage 3.
Stage 1 we will manage in house but we?d need assistance in performing stage 2 and stage 3.
Stage 2: 2 parts will be given and can be run together in TCrig if possible.
Coolant flow rate: a constant 858 LPH and 40C Hot cycle air temp = 180C Cold cycle air temp = 20C Air pressure is 3 bar_abs Air flow is a constant 1000kg/hr
Hot cycle last 54 seconds, cold cycle lasts 54 seconds. The temperature change between the cycles must be completed in 6 seconds.
The test will run to 20,000 cycles, or to failure.
Stage 3: 2 parts will be given and can be run together in TCrig
Large Consumer Products company needs packaging laboratory for ASTM high altitude transporation simulation testing including subject packaged product to a change in vacuum pressure in order to simulate altitude for transportation test of packaging. The product is pouch in a display carton.
USA Toxicology Product Safety Laboratory needed for OECD Testing to Test method B.48 / OECD 438 for GHS/CLP Classification of a mixture. I need a quote for the cost of having this test performed on a mixture that we formulate. One of our suppliers does not have enough information on their SDS in order for us to classify our mixture correctly. We need to know if our mixture will be classified as either 1) causing ?serious eye damage? (CLP category1), or 2) not requiring classification for eye irritation or serious eye damage according to the CLP
USA Product Safety Laboratory needed for DOT Classification Testing DOT Toxicity test for class 6
Analytical Chemistry Laboratory needed fr salt testing. Analysis for impurities, moisture, etc.
University Researcher needs United States laboratory for ASTM Testing: Crude oil classification for rail transportation in the USA Up to ten samples of crude oil.
I would like to test a few crude oil samples for their boiling point distribution/initial boiling point, flash point and sulfur content for the purpose of their classification into packaging group for rail transportation in the USA. Could you please provide me with a price quote for that service. Also, what is the minimum volume of each crude oil sample required for the test?
Physical Laboratory needed for EN Testing: fatigue testing on rail welds according to EN14730-1, Railway applications ? Track ? Aluminothermic welding of rails
Mechanical Laboratory needed for ANSI Testing of new prototype ladder that we need to have ANSI tested & rated; however our current testing facility is not able to perform the test, due to an injury that has put him off work for an unknown amount of time. With all that being said, I am trying to find locations that can perform ANSI testing on our products and give an accredited rating. We are located in KY, so of course the closer the facility is to us, the better due to transportation logistics?. Any assistance you can provide will be greatly appreciated!
Packaging Laboratory needed for EN - ISO Transportation Study: packaging validation testing against (Transportation/ distribution Testing) Our products consist of film and paper sealed on site (produced by our company), we need to know the efficiency of our packaging.
For any clarification and more info. Please do not hesitate to contact me.
Thanks for your usual support!
Automotive Laboratory needed for automotive parts testing. Brake testing to U.S. Dept. of Transportation, National Highway Traffic Safety Administration, laboratory test service for FMVSS 106,Brake Hoses
Essential Oil Manufacturer that is manufacturing oil shipping cartons needs Transportation certification UN laboratory needed for UN certification testing: dangerous goods transportation testing for the certificate for SS containers intended to carry dangerous goods.
Physical Laboratory needed for closure testing: Closure scuffing testing and Transportation testing 200 pieces
Food Microbiology Laboratory needed for food microbiology testing (transportation testing) of ice cream samples, will need transporting refridgerated, will need about 4 samples doing each month for a couple of months
Canada materials laboratory needed for coating testing to B388 Alberta Transportation approval testing for Concrete Sealers and their performance under different weather conditions.
Florida physical laboratory needed for transportation vibration tests on radio assembly as per Mil Std 810 Method 514.6 General Vibration procedures 1 and 2."
Europe, UK or US mechanical laboratory needed for Wear and retentivity testing for rail curve greaseThe test is run on a Twin Disk machine, similar to the Amsler machine used in North America. The twin-roller tribometer runs two cylindrical discs against each other under a preset applied pressure and slip rate between the discs. One disc represents the wheel and one represents the rail track.
Testing of rail curve lubricating grease to British Testing Standard BS EN 16028:2012, Railway applications. Wheel/rail friction management. Determination of the volatile constituents in greases
USA FAA aeronautical Laboratory needed for FAA Testing: AeroMedical device certification for airlines Portable ECG device for airplanes and other transportation needs EMI test for interference with NAV COM of airplanes during flight
DOT Transportation Packaging Laboratory needed for DOT Testing: DOT, Title 49 CFR Packaging - motor oil - bag in a box 11 sample packs
Arizona chemistry laboratory needed for non-hazardous natural charcoal testing for natural charcoal which is going to be shipped overseas in container for " not Haz Material ' "
Analytical Chemistry Laboratory needed for thickness testing and composition testing to measure to courier bags to determine if they have a different composition
USA transportation certified laboratory needed for commodity testing: Charcoal as non-haz commodity for shipping in containers to overease , need certified laboratory
India materials laboratory needed for mineralogy testing to determine type of mineral content is in it.
Canada , US Analytical Chemistry Laboratory needed for Transformation/Dissolution Testing. ooking for laboratory setup to perform the GHS (Globally Harmonized System) Testing for Toxicity Classification by the Transformation/Dissolution test Procedure. Although I refer to the GHS Test Procedure, we require this immediately for the upcoming IMDG Regulations regarding the washing of the ships cargo holds which requires washwater treatment if the material is Classified as Toxic.
IATA transportation laboratory needed for IATA Testing of dangerous goods shipping contianer polyurethane shipper tested so it can have printed on the carton UN3373 4G/Class 6 UN1845 Misc 9
Analytical Chemistry Laboratory needed for fluid testing. Have 1 55 gallon drum of fluid on our ship that needs to be identified. Most likely Industrial marine grade acid cleaner or soap- possibly Alumabrite or Aquasalt 20 20
FAA Transportation Laboratory needed for FAA Photometry testing on reflector. Looking for how much percentage of reflectivity on a scale of 1 to 100% i could get from the reflector. Sample size 1
FDA GMP Packaging Laboratory needed for transportation Shipping testing of box (12"X10"X10") containing two bottles of benign solutions.
Transportation Materials Laboratory needed for UN Dangerous Substances Testing to Testing according to ISO 2137:1985 penentrometer test. Determine pasty substance w.r.t. UN transport of dangerous goods / EU ADR regulation.
Sample is sludge (75% sand with water)
India NABL physical laboratory needed for acoustics and vibration testing: noise meter and vibration meter calibration
Department of Transportation DOT qualified triangles per Federal Motor Vehicle Safety Standards and Regulations FMVSS 125, Warning Signals.
Indiana or Mid-West USA Product Safety Laboratory needed for Department of Transportation DOT/FMVSS Product Safety Testing: TP-125-01 (FMVSS 125 - Warning Devices)for reflective lens/Emergency triangles
Eastern USA Toxicology Laboratory needed for OECD Testing to OECS 202, for transportation Classification (Class 9) under IATA, IMDG and ADR. Daphne acute immobilization and reproductive test. EC 50 / 48 h to determine Class 9 per IATA, IMDG and ADR. Five to ten samples possible.
Analytical Chemistry Laboratory needed for Cyanate analysis of a cadmium cyanide solution. 2 samples
Australia Transportation Laboratory needed for ISTA Testing and ASTM Testing: Temperature conditioning testing, drop testing, vibration testing, compression testing to ISTA 7D, ASTM D642-00, ASTM D4332, ASTM D4169, ASTM D4728-01 110 cartons of size 385mm x 310mm x 390mm
Large Medical Device Company needs Mexico ISO Transportation laboratory for ISTA Testing: Shipping testing
Mechanical Laboratory needed for SAE Life Cycle Testing: liquid hose assemblies to SAE J2045 sect. 4.5 life cycle test.
British Columbia Packaging Laboratory needed for ASTM Testing to ASTM 4169 09 Standard Practice for Performance Testing of Shipping Containers and Systemtesting for paletized packaging using intermodal and over the road transportation.
CANADA Bombardier BAERD GEN-018 ACCREDITED CANADA MECHANICAL ANALYTICAL CHEMISTRY LABORATORY NEEDED FOR EFFICIENCY TESTING OF NEUTRALIZING AND RINSING, THE SPECIMENS SHALL BE CLEANED WITH THF (TETRAHYDORFURAN) AND AFTER EVAPORATIONOF THE EXTRACTION SOLUTION AN INFRARED SPECTRUM SHALL BE PRODUCED. THIS SPECTRUM SHALL BE COMPARED WITH THE SPECTRUM OF THE ELECTROLYTE AND NEUTRALIZER. NO COMMON PEAKS SHALL BE FOUND.
Europe Mechanical Laboratory needed for GMW Testing: Air induction duct performance and durability Testing to GMW 15143
ASIA ANALYTICAL CHEMISTRY LABORATORY NEEDD FOR EXPORT TRANSPORTATION QUALITY CONTROL TESTING OF NaCn . Need know if could do the test before Shippment on samples choosed of all product for export, and so we confirm the quality in the contract, so need price and time of report .
Shanghai, China Transportation Laboratory needed for US DOT Testing in Compliance with US Department of Transportation FMVSS125 StandardUSDOT FMVSS125 description.
Geology Laboratory needed for mineral testing of railway ballast to determine mineral consistency of the rock
Eastern USA Transportation Laboratory needed for Shipping Studies for Dietary Supplements in bottles.
USA Shipping and Transportation Laboratory needed for Temperature and humidity chambers, drop testing, vehicle vibration testing, altitude testing, loose load vibration testing, vehilce stacking
Oil Shipping firm needs Oil and Petroleum Laboratory needed for oil analysis of oil on 20 vessels
Germany and Kuwait analytical chemistry Laboratory needed for chemical analysis of Chemical substances in the German and Kuwaiti ports
Saudi Arabia Transportation Laboratory Testing needed for oil analysis used in vessels.
Physical, Mechanical Laboratory needed for reliability testing of locomotive duty pre-lube pump Start/stop tests under various thermal conditions (40 to 280 deg. F) 8000 cycles lasting 5 to 35 min. Requires temperature control of oil, but ambient temperature can vary.
Europe Transportation laboratory needed for ASTM or ISTA Testing : Transport simulation testing for medical devices in shipping cartons
Southern USA Oil and Petroleum Laboratory needed for SAE Testing, on road or on track testing to SAE J1321 specs. Device to be tested go to www.supertech.it
Europe Oil and Petrolem Laboratory needed for ASTM, ISO or GPA Testing of natural gas fixed gases, methane ethane, propane, butanes, pentanes in pm; C6 to C8 in parts per billion.
India metallurgical laboratory needed for metallurgical quality control testing of Rail wheel
Microbiology Laboratory needed for microbiological analysis on Handling Vessel They have investigated the toilets itself. Therefore we would like microbiological research test to find out if it could be a bacterial problem.
Acoustics Laboratory needed for measuring sound level near Air port & railway track in mumbai vileparle area, at night 11.30 PM the readings taken by us in presence of your representative, that should be certified by you as you are having necessary accreditation from Recognize institute.
India Physical Laboratory needed for ASTM Testing, stone polish value test for bituminous concrete job mix design
Eastern USA Materials Laboratory needed for SOLAS fire-fighting foam analysis Analysis of the characteristics of foam to be used for fire-fighting purpposes onboard oceantrading cargo vessels, according to SOLAS regulations and Manufacturers specifications.
Packaging laboratory needed for non-destructive, ISTA - 3H testing - metal racks and plastic container with dunnage.
India Physical Laboratory needed for ASTM Testing Barcol hardness test to ASTM D2583 on Chockfast orange (similar type of hard resin)"
USA Packaging Laboratory needed for ISTA 3B packaging testing to ISTA 3B for a medical device (up to 800lbs) Additionally we require testing to the following parameters: Relative RH, non-condensing: 30 - 75% Barometric pressure: 10.15 - 15.4 PSI (700 - 1060 hPa) Shipping and Storage Ambient temperature: -10-104F (-23 - 40C) Relative RH, non-condensing: 30 - 90% Barometric pressure: 10.15 - 15.4 PSI (700 - 1060 hPa)
Australia electrical laboratory needed for Testing and analysing the behaviour of AC traction and propulsion system (including 4Q converter and DSC inverter) in rail traction during the regeneration. This is a PHD research study.
UKAS Europe transportation or civil engineering laboratory needed for BAM Lighting and safety elements for roads Photometric characteristics of road studs - Warning lights at working sites - photometric testing of traffic lights
"medical device product and packaging shelf life testing. Require quotation for ASTM,ISO, and ISTA standard conditioning and tests for accelereated aging, transportation simulation, environmental conditioning"
Acoustics, Materials Laboratory needed for Noise Absorption test of noise barrier panels Test to German highways ZTV-LSW 88, or EN 1794 (or BS EN1794)
Transportation Laboratory needed for medical devices transportation testing, ie. packaging validation
Eastern USA Materials Laboratory needed for DOT Hazardous Materials Testing Analyzeto determine if Hazardous Materials Transportation Class/Divisions 4.1, 4.2 and 4.3 apply.
Europe Mechanical Laboratory needed for testing the chemical composition of rail clips and why they do not return to their original stated toe load when removed from the track. The required toe load of the clips is 8kn per clip (14-16kn toe load per rail pad).
United Arab of Emirates, India, Middle east countries, UK, Canada, Europe EN Mechanical Laboratory needed for Micro Deval Test - Railway Ballast in accordance to EN 1097-1 - Under EN 1097-1:1996, the 10mm, 11.2mm (or 12.5mm) and 14mm sieve sizes shall be replaced by 31.5mm, 40mm and 50mm sieve sizes. The sample is divided and placed in a series of drums of specified dimensions with a quantity of steel balls and the drum is rotated at 100 revolutions per minute, for 14 000 revolutions.
California AREMA/IEC Electrical Laboratory needed for power supply testing-Ripple immunity, 34.5 Vdc @ 40A with 2.4vpp 60Hz & 120Hz ripple as per AREMA 2009, IEC 61000-4-29.
USA ASTM Dynamics/Mechanical Laboratory needed for simulation testing of long distance over-the-road shock and vibration simulation as per ASTM D4169. The test unit weighs about 10,000 pounds, is 4 feet in diameter X 7 feet tall.
Electrical Laboratory needed for electrical testing: 1. Basic Insulation Level Impulse Test 2. Corona Test 3. Ground Bus Test 4. Current Withstand Test
Alabama Analytical Chemistry Laboratory needed for ASSHTO Testing to ASSHTO Methods T-288, T-289, T-290 and T-291 Chemical Analyses (pH, sulfates, chlorides, resistivity)
North America Mechanical Laboratory needed for UL Testing Impact Strength (D5628) and Thermal Cycling Withstand Test(C37.55 2002 A5.1) on samples of copper bus coated with Hysol Dexter epoxy coating and DuPont epoxy coating.
Analytical Chemistry Laboratory needed to set up temporary mobile lab at Palouge Site Feed Processing Facilities and provide Laboratory Testing apparatus along with reagents and chemicals. We require a Lab Chemist for collecting and Testing the Samples and need another Oil Specialist to suggest and improve testing methods and interpret the Results. Testing of Samples Required: 1. Crude/Water/Gas Feed to FPF: Water content (Free water / Total water), Sp. gravity, Viscosity @38 DegC / 75 DegC / 85 DegC / 105 DegC, Asphaltene content, Basic Sediments & Solids (Sand), Pour Point, Total Acid Number, Field test of foaming tendency, free settling etc 2. Crude at O/L of First Stage Separators: Water content (Free water / Total water), Sp. gravity, Basic Sediments & Solids (Sand), Pour Point. 3. Crude at O/L of Second Stage Separators: Water c
India Packaging Laboratory needed for package testing one of our products as per ISTA 2A
USA PACKAGING COMPANY NEEDS ISTA APPROVED TRANSPORTATION LABORATORY FOR TESTING CLIMATE CONDITIONING, RANDOM VIBRATION DROP TEST, POST DISTRIBUTION VISUAL INSPECTION
Large Pharma needs Europe ASTM Transportation Testing Laboratory for testing 1 pallet with 12 shipping cartons for manual handling drop test, vehicle stacking compression test, loose load vibration, vehicle vibration, warehouse stacking as per ASTM D4169-05
Tin Can Manufacturer needs Australia Metallurgical Laboratory for ASTM testing to determine the % scratches, dented & packing after shipping to that particular country as per ASTM standards.
Asia/USA Mechanical Laboratory needed for AASTHO Testing for the following parameters: Weight Grab Elongation % Grab Tensile (Lbs) Trapezoid Tear ( Lbs ) Puncture ( Lbs ) CBR Puncture AOS (mm) US sieve 40 Mullen Burst Permittivity (Sec-1) Permeability Uv Stability@500Hr
India ASHTO Laboratory needed for transportation testing to obtain certification for geo-textiles for the construction industry.
Texas Product Safety Laboratory needed for testing sample release agent for approval for Texas Department of Transportation-specification will be provided
Taiwan Packaging Laboratory needed for testing shipping cartons for lighters requiring UN specification packaging for US49CFR, IMDG, IATA, TDG transportation
Eastern Pennsylvania Packaging Laboratory needed for testing as per ISTA 1 A for TV Set Top Boxes, 4 drop test and 3 Vibration test.
Changchun (China) & Singapore Acoustics Laboratory needed for noise testing (static & dynamic) to be carried out both externally and internally on the trains.
Metallurgical Laboratory needed to run spectrographic analysis of steel or steel alloys - please advise cost.
USA ASTM Laboratory needed for Packaging and Transportation testing according to ASTM D4169 and/or D7386
Electrical Laboratory needed for thermal conductivity testing i.e temperature carrying capacity w.r.t current the 10sqmm, 25sqmm, 50sqmm & 120sqmm aluminium cable connectors without breaking i.e damaged per below standard - IEC document No. 91/28490 and the extend-ed load cycling test regime of BS 4579
ASTM Packaging/Mechanical Laboratory needed for the following testing: SEQUENCE: 1 ELEMENT: A Manual Handling Distribution Simulation Hazards incurred during manual handling such as loading, unloading, dropping, throwing, stacking, sorting or palletizing. DESIGN TESTING PRACTICE FORM Delphi Electronics & Safety PKG WI FOR 651.01.02A Effective Date: March 12, 2006 2 Test Standard- ASTM D4169 (latest revision) Equipment - Lansmont drop tester model PDT-56E Conditioning - ambient Drop Height - 21 inches Drop Sequence - bottom, bottom edge, adjacent bottom edge, bottom corner, diagonally opposite corner Results: SEQUENCE: 2 ELEMENT: D Vehicle Stacking Distribution Simulation Compressive loads that occur during vehicle transport or warehousing. Test Standard- ASTM D4169 (latest revision) Equipment -Lansmont model 765K compression test sys
HK Asia FDA/ISO Packaging Laboratory needed for testing the resistibility of our products packages during Air, Sea and ground transportation Number of samples - 3
Central USA Mechanical Laboratory needed for testing 2,200 L Fuel tanks for vibration to "Single Container Resonance Test in ASTM D 999-96, Method B, at the test severity, time schedule, and amplitude recommended in Method B. The tank is steel and will weigh 3000 lbs, plus the tank needs to be filled with water to 95%, which adds another 4700 lbs. The tank must not rupture or leak during test.
India IEC Laboratory needed for testing as per IEC 61373,wt of equipments with fixture is 3,500 kg
Analytical Chemistry Laboratory needed for PCB testing of an offshore vessel for PCB's in the paint.
India ISTA IA Laboratory required for testing designed packaging corrugated boxes for ISTA 1A standard and some other standards if applicable.
Environmental Toxicology Laboratory needed for aquatic toxicity testing for raw material that has environmental N-hazard labeling and R51/53. In same cases (at high loading) this will affect the labeling of the final formulation. In these cases the whole formulation get N-hazard labeling, R51/53, and also get UN-number 3082, related to transportation. That means, there are some constrains in transportation. We would like to get you advice on the testing to be performed in order to delete the N-hazard labeling and reduce R51/53 to R52/53.
Laboratory to test Mexican packaging product to obtain UN specification number for Air HAZ MAT transportation.
Physical Laboratory needed for EN 15152 testing gravelling impact resistance on Front windscreens for train cabs
Eastern USA Transporation Laboratory needed for Transportation Simulation Testing, Package Testing Salt, Fog & Cyclic Corrosion Testing Temperature & Humidity Cycling, Vibration & Shock Testing
Analytical Chemistry Laboratory needed for ASTM Testing, ASTM F-2466. Determining silicone volatiles in silicone rubber for transportation applications.
Eastern US ASTM Packaging Laboratory needed for testing materials according to UN3373 and PI 650 IATA guidelines for shipping biologicals
Canada, British Columbia Vancouver area ISTA level 2 assurance Packaging Laboratory required to test Random Vibration, oscillatory, drop testing. Should simulate ocean container handling, vessel loading, and over the road.
Dallas DIN 51381 / ASTM D3427 Analytical Chemistry Laboratory required for Air release time testing.
FDA 510(k) Preclinical Contract Research Organization required for: Medical Device Design and Modelling of Systems Medical Device Compliance Testing Reuseable Medical Devices Testing Medical Devices Methods Development and Validation Testing Medical Devices Transportation Simulation Studies Need estimates within the week for budget deadline.
Eastern USA ASTM - ISO Materials - Product Safety Testing Laboratory required for Flammability Testing, Toxic Elements Testing, Ignitability Testing, Hazardous Substances Testing, Toxicity Testing, Volatile Organic Chemicals Testing, Chronic Hazards Testing, Hypersensitivity Testing, Electrical Safety Testing, Safety Certification Testing, Safety Compliance Testing, UV Protection Testing, Fatigue Testing, Acoustics Testing, Waterproof Performance Testing
USA Transportation Laboratory neededed for Mil-Std 331 Vibration testing, jolt test, Temperature & Humidity, Impact shock (airgun)
Packaging Laboratory needed for DOT, UN, and Hazmat Testing on combination packaging, 4 X 1 Gallon Jugs in corrigated box
USA Microbiology Laboratory needed for fabric disinfectant testing to determine if textiles are free from bacteria, viruses, and fungus.
Singapore ISO metallurgical laboratory needed to analyze / check material chemical composition and mechanical properties of 304 stainless steel samples cut out from ship's cargo pipe line system.
Transportation Laboratory needed for ASTM Vehicle Testing: ASTM D 4169-05: Schedule C:- Vehicle Stacking Schedule E:- Vehicle Vibration Schedule F:- Loose Load Vibration Schedule I :- Low Pressure A (High Altitude) Schedule A:- Handling Schedule B:- Warehouse Stacking
US Physical Laboratory needed or UN Performance Testing: DOT 7A type A packaging 49 CFR 173.412, 173.415, 178.350 and industrial IP-3 49 CFR 173.411 Type IP-1 49CFR 173.410, 411(a) and (b)(1)
Large cosmetics manufacturer needs Canada packaging laboratory for TDGA testing, Transportation of Dangerous Goods, burn rate test
European Packaging Laboratory needed for HAZMAT UN Standards Corrugated Box Performance Testing for HAZMAT Transport
Analytical Chemistry Laboratory needed to test oil as per US Standards. We are using a Rust preventive oil to coat on SG Iron Component bound for export to US via Ship container. The Oil forming a layer a sort of Plastic thin sheet which is not acceptable at US Customer M/s We need to test our RP oil for the US Company standards.
Singapore or closeby Metallurgical Laboratory needed to identify the reason of periodically Broken studs of Cylinder covers on Ship's Main Internal Combustible Engines Makita B&W 6L35MC. We have broken studs in office. We are looking for Laboratory in Singapore which can make Material Failure Analyses testing which includes a Fractography, Metallographic and hardness analyses. What will be your quote?
Toronto ASTM F1980 Medical Device Testing Laboratory needed to perform as per - ASTM F1980 without testing the sterility clauses - Aging & Shelf Like packaging testing - Transportation/Distribution SImulation - Package Integrity Testing - Package Strength Testing - Do not Include sterility sections because the product is not marked sterilized Can you advise 3 labs in toronto area who can perform this request? Thank you. The product is a dental material used for Coping . It is called Alumina Ceramic.
Europe ASTM E 662 ASTM E 162 ASTM D 2863 FMVSS 302 FAR 25 Part I horizontal and Vertical and Part IV and Part V Fire/Flammability Testing Laboratory needed.
India Metallurgical Laboratory needed for port inspection of Iron ore in the stock yard of Krishnapatnam port.
Canada Laboratory needed for IAEA, USDOT Dangerous Goods Testing: Test 9 meter drop test on packages weighing from 10 to 50kg. Possibility of performing this test at cold temperature also.
Large Beverage Manufacturer need food laboratory for mocon headspace oxygen testing of closed flexible packageing containing coffee; flowability; water activity and moisture anaylsis(this is a transportation study our product will be on pallet in our distribution centers) Will need to samle approximately 250 samples depending on pallet configuration
Analytical Chemistry laboratory needed for ASTM F2466-05 Standard Practice for Determining Silicone Volatiles in Silicone Rubber for Transportation Applications
Analytical chemistry laboratory needed to test prototype coated fabric for transportation of milk. Need to test for heavy metals (e.g., Cd, Pb, Hg) and for bisphenol A in fabric. They are also requesting the assessment of the Evaporation Residue Test per the specification on Page 86 of rhe JETRO document.
Physical laboratory needed for testing for internal product leagkae from suspected air frieght transportation problem Testing to include cutting open devices and inspect for internal product leakage. Product suspected air freight transportation problem.
GMP Microbiology laboratory required to perform Microbiological sterility testing (aerobes, anaerobes, fungi) for process validation of biological product. This will require some custom setups and transportation of test samples. Testing lab must be within 1-2 h drive from New York City
Microbiology Laboratory needed for Microbiological sterility testing (aerobes, anaerobes, fungi) required for process validation of biological product. This will require some custom setups and transportation of test samples. Testing lab must be within 1-2 h drive from New York City"
Environmental laboratory needed for testing 2 Traffic encoders one 11in x 3in x 8in one 8in x 8in x 4in 12V Power both tested for 8hrs at 74C and 85C
Packaging laboratory needed for Transport of Dangerous Goods testing: Determination of solid oxidizer packaging group.
USA Materials laboratory needed to perform ISO testing for oxygen index on insulating foam used in transportation to ISO 4589-3
Physical laboratory needed for Transport of Dangerous Goods testing: Determination of solid oxidizer packaging group.
Petrochemical laboratory needed for testing fuel quality at various points in distribution system. 2. Determining cause of contamination, if any, in the fuel transportation and distribution system. 3. Analyzing relationship if any between fuel quality and fuel system failures in motor vehicles.
Materials laboratory needed to perform ISO testing for oxygen index on insulating foam used in transportation to ISO 4589-3
USA Materials lab needed for testing to AWS D1.5 and HAZ CVN. Looking for machining of test specimens rather than the actual testing.
Looking for 3 types of quotes: 1. machine & test 2. machining only 3. machining, with photo documentation of location of each specimen location from within the original sample (if not part of SOP)
Company needs to find a lab that perform testing on samples of Magnesium materials by products that are scheduled for recycle and determine flammability for DOT transportation requirements when transporting by highway