Contract Laboratory has received the following Physical Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Physical Laboratories to perform their Physical Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Physical laboratory that would like more information on these Physical projects, please visit our registration page or call toll us free 1-855-377-6821.
Test Request 17-01790
Test Request 17-01778
Pharmaceutical Analytical Chemistry Laboratory needed for conducting studies on the Active Pharmaceutical Ingredients APIs in an oil in water emulsion. We need to arrive at following conclusions by morphological/physical/chemical testing etc
1. Whether APIs are dispersed or solubilized (both APIs).
2. Phase in which each API is present (dispersed phase of emulsion or continuous phase of emulsion)
3. Particle size of API (for dispersed API). Separate PSD for each API if both are dispersed.
4. Globule size of emulsion.
Test Request 17-01355
Medical device laboratory needed for drug compatiblity testing and testing of parenteral IV containers to ISO 15747:2010 which contains requirements that relate to the safe handling and the physical, chemical and biological testing of plastic containers for parenterals.
ISO 15747:2010 is applicable to plastic containers for parenterals having one or more chambers and having a total nominal capacity in the range of 50 ml to 5 000 ml such as film bags or blow-moulded plastic bottles for direct administration of infusion (injection) solutions.
On the same lines I need to collaborate to test the following in my products:
(i) Ideal Uniform Self Collapsibility
(ii) logarithmic volume measurement for infused volume
(iii) No Exchange of Hazardous Contaminants with Environment
(iv) Residual Volume in Container
(v) No Suck Back in the container
(vi) No Contamination during Admixing
(vii) Drug Compatibility
Test Request 17-01338
Large corporation needs physical laboratory for failure analysis of injection molded waterproof housing submitted to a leak test, t. It has been observed that air bubbles are coming out at some locations that coincide with a knit line, there is a theory that the knit line is actually a mico crack that allow air to come out. I'd like to perform an x-ray of the area and then perform a cross section to determine how this knit line propagates if this in fact a microcrack.
Test Request 17-01139
Laboratory needed to measure thermo-physical properties of fuel additive mixtures containing ethylene, vinyl acetate and cyclohexane. Properties to measure include: critical point determination, viscosity of mixtures, density of mixtures, vapour pressures, compressibility factor, specific heat capacity, pressure-vapour temperature in liquid (supercritical and vapour phase), Vapour-liquid equilibrium data of mixtures
Test Request 17-01091
Construction materials laboratory needed for physical testing of Fiber Reinforced Polymer (FRP) Reinforcing Bar including 160 samples tested for durability in accordance with the following standards:
-AC320 (an acceptance criteria from ICC)
-Conditioned for 1000 and 3000 hours using ASTM D 2247
-ASTM C 581 Standard Practice for Testing Water Resistance of Coatings in 100?% Relative Humidity
Test Request 17-00900
Medical device laboratory needed for physical ASTM testing of a range of titanium surgical-grade products to the following ASTM Standards: ASTM F2052 Test Method for Measurement of Magnetically Induced Displacement Force on Medical Devices in the Magnetic Resonance Environment, ASTM F2119 Test Method for Evaluation of MR Image Artifacts from Passive Implants, ASTM F2182 Test Method for Measurement of Radio Frequency Induced Heating On or Near Passive Implants During Magnetic Resonance Imaging, and ASTM F2213 Test Method for Measurement of Magnetically Induced Torque on Medical Devices in the Magnetic Resonance Environment
Test Request 17-00881
Medical Device Laboratory needed for microbiology and physical testing of medical drapes and surgical gowns to several EN ISO standards:
1. EN ISO 22612 Resistance to Microbial Penetration - Dry,
2. EN ISO 22610 Resistance to Microbial Penetration - Wet,
3. EN ISO 11737-1 Cleanliness - Microbial,
4. EN ISO 9073-10 Cleanliness - Particulate Matter/Linting,
5. EN 20811 Resistance to Liquid Penetration
6. EN ISO 13938-1 Bursting Strength - Dry,
7. EN ISO 13938-1 Bursting Strength - Wet,
8. EN 29073-3 Tensile Strength - Dry and,
9. EN 29073-3 Tensile Strength - Wet
Test Request 17-00672
ISO 17025 certified laboratory needed for OECD physical / chemical testing of solid materials and an octanol / water solution as per three OECD standard methods: OECD107 Partition Coefficient (n-octanol/water): shake flask method , OECD 117 Partition Coefficient (n-octanol/water), HPLC method, and OECD123 Partition Coefficient (1-octanol/water): slow-stirring method
Test Request 17-00652
LONG-TERM TESTING Materials laboratory needed for ASTM physical, mechanical, and accelerated aging testing of polymer auto parts to car manufacturers specifications WSS-M2D496 (Ford), GMW 14196 (General Motors), MS-AY-549 (Chrysler-Fiat) including:
Density to ASTM D3574-16 Test A
Tensile Strength to ASTM D3574-16 Test E
Elongation at Break to ASTM D3574-16 Test E
Tear Strength to ASTM D624 Die C
Compression Set to ISO 1856 Method A
Compression Deflection Stress ISO 3386-1 +A1
Heat Aging to ASTM D3574-16 Test K, ISO 3386-1 +A1
Humidity Aging to ASTM D3574-16 Test J, ISO 3386-1 +A1
Dimensional Stability to WSS-M2D496, 3.5.10
Fogging to SAE J1756
Odor to FLTM BO 131-03 Variant B
Cold Flexibility to FLTM BN102-01 Method A
Solvent Resistance to WSS-M2D496
Flammability to ISO 3795
GMW 14196 Testing
Emissions per GMW 15634 (VOCs, SVOCs)
Emissions per GMW 15635 (Carbonyls)
Emissions per GMW 3205 (Odor)
Emissions per GMW 3235 (Fog)
Compression Force Deflection per ISO 3386-1 40% Compression
Mass per GMW 3182
Thickness per ISO 1923 or ISO 2589 depending on Type
Flammability per GMW 3232/FMVSS-302
MS-AY-549 Chrysler Fiat
Compression Deflection per ASTM D 3574-16 Test C 25% Compression
Aged Compression/Deflection Humidity Aged per ASTM D3574-16 Test C and J at 25% deflection
Aged Compression/Deflection Oven Aged per ASTM D3574-16 Test C and K at 25% deflection
Test Request 17-00574
Polymer laboratory needed for nondestructive NDT Testing: heat resistance testing of an acrylic lens according to IWA MIL-PRF-5425. Also, need physical properties such as elongation, tensile strength testing of O-rings made out of 51+/-5 durometer EP rubber compounds according to E5001B, E1100-50, EA454-50 or chemically equivalent.
Test Request 17-00417
Physical laboratory needed for DIN Testing of automotive parts to 5.9 Solar Radiation Test as per DIN 75220, D-OUT-F
Test duration 1 cycle = 240 hrs.
Test chamber temp = 42 oC, RH 65 %
Radiatlon intensity 1000 W/m2
5.10 Dust Test
- execution as per ISO 16750-1, resp. ISO 20653
- Preparing of the test samples; without sealing and without producing of testing 1 cycle:
- Swiriing of dust in chamber for 6s
- Dust deposits for 20 min - Total of 20 cycles
- Type of dust: Arizona dust A2
Operation mode 3.2 for 5 min (necessary to specify operating voltage)
- Evaluation - dismounting of sample and check of dust ingress (necessary to specify) - 1 sample tested in 1 load
Test Request 17-00356
Plastics / Materials Laboratory needed for ASTM physical testing of plastic crates from different suppliers including:
Raw material tests as per ASTM D4976 + ASTM D5203, density, melt flow rate, elongation at break, tensile strength, UV resistance, stress crack resistant, impact test as per SASO-GSO 1863.
Test Request 17-00218
Business Request 17-0012
Wishing to purchase laboratories located near or around Central Jersey. Also, the laboratory could be purchased for licensing and moved. There are many different variables such as accreditation, insurance mix machine, and so on so I would be interested in looking at all opportunities. This would include any lab since Toxicology could be added. The price range is determined by the specific deal. Also if to only the lab could be purchased for the licensing and moved to a desirable location since servicing allows for distance from location with receiving samples of of state or geographic location of the physical lab.
Test Request 17-00011
Polymer laboratory needed for EPA and ASTM materials testing of a O/W micro-emulsion matrixColor; Physical State; Odor; Explosive Properties; Oxidising Properties & Incompatibility; Flammability; pH; Non-Newtonian Fluid Dynamic Viscosity; Relative Density; Storage Stability at 54 C for 14 days and ASTM G31 Corrosion Characteristics.