Laboratory Outsourcing and Scientific Sourcing Center

Looking for a Calibration provider in Dammam for our Mechanical and Chemical Testing equipment.

MULTIPLE TESTING

BUDGET APPROVED ($1,000-$2,000)

We need mechanical tests per the ASTM A370-24 (Standard Test Methods and Definitions for Mechanical Testing of ...

Looking to test drip irrigation tapes according to ISO 9261.
How many working days does it take?
How much does it cost?

(ISO 9261:2004 - Emitters and emitting pipe)...

We are looking for flame penetration testing with the UL-181 standard. Our product is a flexible, uninsulated air duct made with a fabric exterior and steel wiring. The produc...

A Turboexpander and Compressor manufacturing project in Japan for cryogenic industries needs a laboratory to perform a strain gauge test.

We have a new requirement for spark-proof evaluation of inverters,
driven by the introduction of the next-generation refrigerant R290.

We intend to conduct engineering tes...

We need to test valves with low-pressure air to calculate pressure losses. Pressure from 5 mbar to 100 mbar; size from 1 to 4.

Need a bench-top oven/furnace that can reach 1200°C/2200°F or more to heat a small sample (with zero volatiles).

Please respond quickly.

Looking to identify substances inside a mechanical steel tube used in an automotive steering linkage system using a mass spectrometer. Have several samples ready to test. Plea...

Need a Delhi / India lab for EMI/EMC on-site testing and CE certification for low voltage directive (LVD) equipment.

MULTIPLE PRODUCTS

We need a calibration certificate from an ISO 17025-certified laboratory in Kuwait / UAE for the following equipment:

1. Ground Penetratin...
   Closed

A US-based lab is needed for testing of a material that looks like sand that was found in some equipment, we don't know what the material is but we have some material to compa...

MULTIPLE TESTING

Materials Laboratory needed for the following testing:

1. Solid Specific Gravity

2. Liquid Specific Gravity

3. Slurry Specific G...

Materials laboratory needed for testing winch sheave with plastic-like coating. We want to determine what that material is. We would be able to send a small sample to your fac...

Electrical Laboratory needed for ASTM testing of polyester fiberglass material for dielectric breakdown per ASTM D3426 (Standard Test Method for Dielectric Breakdown V...

QUEBEC / CANADA Energy management multinational company needs ISO 10447 quality testing for a new welding station at their fabrication shop.

Do you offer this type of se...

URGENT

CALIFORNIA Environmental laboratory needed for discharge water testing from industrial cutting equipment.

Lab preferred around Stanislaus County.

Contract laboratory (Canada-based preferred) needed for testing breathing air sampling kit and compressed breathing air.

Construction Materials Laboratory needed to determine the heavy metal (such as Mercury and Arsenic) limit in thermal insulation per regulations in different regions.
Thank yo...

Contract laboratory needed to conduct ANSI/ASME PVHO-1 (Safety Standard for Pressure Vessels for Human Occupancy) testing for hyperbaric chambers.
We require a document for ...

INDIA Independent engineering research facility needed to calibrate level transmitter.

Looking for a facility with accessories that can support pyrotechnic testing (Pyrotechnic Hall). Please find the details at https://nssd.navy.mil.bd/front-specification-pdf/0...

URGENT
THAILAND Contract laboratory needed for testing three-section hot sticks per the ASTM F711-02 (Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and T...

MULTIPLE TESTING
Third-party facility (India-based preferred) needed to perform heat transfer performance and pressure drop test on a fuel-cooled oil cooler used in heat exch...

EUROPE third-party laboratory needed for assessing Volatile Organic Compounds (VOC) permeability through a membrane used in heat exchangers.

INDIA Third-party contract laboratory needed to perform noise reduction coefficient test on acoustic panels made of fiberboards.

MULTIPLE SAMPLES & TESTING
Contract laboratory needed for testing the following products per the ASME QME-1:2017 standard (Qualification of Active Mechanical Equipment Used i...

We are looking to commission a contract lab for the following testing: Root cause analysis (failure mode analysis) for the incident product.
This should include arc failure ...

MULTIPLE TESTING
Contract industrial equipment testing facility needed for the following analyses on thermal oil sample:
- Flashpoint pmcc
- Flashpoint coc
- Fire point co...

Accredited Contract laboratory needed to provide approval certification for Aluminium couplings according to NFPA 1963 (Standard for Fire Hose Connections).

MULTIPLE TESTING
MULTIPLE SAMPLES
Independent Laboratory needed to run IEEE C57.12.31.2010 (Standard for Pole Mounted Equipment) & IEEE C57.12.30.2010 (Standard for Pole-Mou...

Materials Laboratory needed for ASTM testing of Joint Treatment Materials for Gypsum Board Construction (ASTM C474-15) to measure the viscosity of fluids in Brabender units.

Contract Laboratory needed for VOC & formaldehyde testing as per Mahindra G001730 (acceptable limit for formaldehyde and other carbonyl compound emissions in vehicle interiors...

Utah contract labs or facilities housing flame atomic absorption spectrophotometer (AAS) needed to install the correct ventilation system for a flame AAS we have.
We want to ...

Third-party testing facility needed to conduct the following testing on an 8.5-inch polycrystalline diamond compact (PDC) drill bit
- Rate Of Penetrations (mm/s)
- Impact re...

Third-party laboratory with a Photoluminescence system needed to analyze oxygen-excess related defects in a few silica glass (SiO2) samples. These defects are usually denoted ...

Third-party audio testing laboratory needed for ANSI testing for the US' noise reduction rating (NRR) of 29 dB of headset products, per the American standard ANSI S3.19-1974 (...

Company wishes to purchase a new ICP 5800 (Inductively Coupled Plasma - Optical Emission Spectrometer) needed.
BUDGET APPROVED ($10,000-$25,000)

Independent research lab needed with a temperature chamber needed for thermal testing of a product.
Temperature range: 0°C to 50°C, no humidity.
Must be operational during ...

MULTIPLE TESTING
Contract Laboratory needed for CSA Testing of steel pipes as per CSA G401-14 Corrugated steel pipe products

MULTIPLE TESTING
Contract Laboratory for Scaffold Safety Net testing:
AS/NZS 4389:2015 Roof safety mesh
AS/NZS 1891.1:2007 Industrial fall-arrest systems and
devices
AS/N...

MULTIPLE TESTING
Contract Laboratory needed for TO-17 and TO-15 compliant clinical air/breath sample testing of .having (i) thermal desorption tubes and (ii) Entech silonite ...

LONG-TERM TESTING
CLIA High Complexity Laboratory familiar with Toxicology to conduct validation for a simple screening tool to screen/validate synthetic and fake urine. We a...

Contract Laboratory needed for ASTM hardness testing on helicopter flight controls as per standard test method for vickers hardness of metallic material ASTM E384 Standard Te...

Contract Laboratory needed for NRR noise reduction rating for earplugs

MULTIPLE PRODUCTS
MULTIPLE TESTING
Large Industrial Company needs Contract Laboratory for stability testing for steel bearing components at specific times and temperatures. ...

MULTIPLE PRODUCTS
USA Contract Laboratory needed for SAE Certification Testing of quick coupler valves as per SAE-AS7413 Coupling Assemblies, Quick Disconnect, Automatic Shut...

Contract Laboratory needed for flow testing to determine the Cv value for a valve.
To do this you would need to measure the pressure drop across the valve when flowing approx...