Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Tensile Laboratories to perform their Tensile Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Tensile laboratory that would like more information on these Tensile projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Materials laboratory needed for IEST and ASTM Clean Room Gloves Testing: 1 Tensile Strength ASTM D412 2 Ultimate Elongation ASTM D412 3 Surface Resistivity @50%RH ESD/EOS S11.11 4 MVTR 5 Shedding and extractables - IEST RP-CC005.4 LPC ? 0.5 ?m, Cl?, NO3-, Zn2+, SO42+, Na?, K?, Ca2+, Al3+, Fe3+, Cu2+, Total NVR in IPA
Laboratory needed for multiple testing on tape product AAMA 713 AAMA 711 AATCC 127 ASTM D412 ? Tensile Strength ASTM D 1970 Water Penetration ASTM D 3300 Adhesion and accelerated aging (multiple Tests) ASTM E331 For Exterior breather membrane : - ASTM D-1117 ASTM-D882 ASTM E2178-11 ASTM E2357-11 ASTM E96 Method B AATCC 127 per AC38, ASTM E84 and UV exposure/aging NFPA 285,
Airtight interior membrane: - http://www.astm.org/Standards/E2178.htm
ASTM D-1117 ASTM-D882 ASTM E96 Method B AATCC 127 per AC38, ASTM E84
ASTM Testing of aluminum honeycombs to multiple ASTM standards: .ASTM C273 - Standard Test Method for Shear Properties of Sandwich Core MaterialsASTM C365 - Standard Test Method for Flatwise Compressive Properties of Sandwich CoresASTM C297 - Standard Test Method for Flatwise Tensile Strength of Sandwich ConstructionsIf you offer testing of aluminum honeycomb core, please provide a quote the three tests and for multiple honeycomb cell size.
Europe electrical laboratory needed for IEC tests on fibreoptic cables according to IEC IEC 60793-xx and 60794-xx standards: Testing fibreoptic cables on tensile performance, abrasion resistance, crush, impact, bending, kink, temperature cycling, water penetration, attenuation, PMD, chromatic dispersion, fire resistance, according to IEC Standard 60793-xx and 60794-xx. Following tests are required: IEC 60793-1-40 IEC 60793-1-48 IEC 60793-1-42 IEC 60794-1-2-G7 IEC 60794-1-2-E3 IEC 60794-1-2-G1 IEC 60794-1-2-E1B IEC 60794-1-2-E2B method 1 IEC 60794-1-2-E3 IEC 60794-1-2-E4 IEC 60794-1-2-E6 IEC 60794-1-2-E7 IEC 60794-1-2-E10 IEC 60794-1-2-E10 IEC 60794-1-2-F1 IEC 60794-1-2-F5B
Nanotechnology company needs materials laboratory for conducting studies on nanoparticles effect on the base polymers. polymer composite testing on various polymers, including PP, PE, Nylon, TPU, and others. In particular, we are interested to learn the mechanical performance (Tensile Strength, Izod Impact, Young's Modulus), Gas Permeability, Colorant Properties, Coefficient of Friction reduction, creep properties, thermal conductivity, and electrical conductivity polymer samples: Tensile Strength, Young's Modulus, Gas Permeability, Thermal Conductivity, Electrical Conductivity, Impact Strength, Creep, UV Irradiation, Colorant, Melt Flow Index, Nucleation
Biomechnical laboratory needed for sports performance testing of Cardio machine - 800 lb. including weight limit, calories burned, tensile strength of metal or wear and tear including which muscles of the body and which areas of fat the machine burns i.e. quads, calves, abs, legs, torso etc. Calories burned per half hour, etc.
Construction Buildings Materials company needed for ANSI or ISO adhesive testing to ANSI A118 or ISO 13007 Test adhesive tensile strength at normal temperature and water immersion *Determination of tensile adhesion strength - C *Determination of open time * Determination of slip
Construction Buildings Laboratory needed for ASTM Testing for Prefabricated Vertical Drains 1. Width ASTM D 3774 2. Thickness ASTM D 5199 3. Discharge Capacity qw , straight & folded ASTM D 4716 4. Tensile strength, elongation at break, elongation at 1kN (full width test) ASTM D 4595 5. Apparent Opening Size O95 ASTM D 4751 6. Permeability, permittivity ASTM D 4491 7. Grab tensile strength ASTM D 4632 8. Trapezoidal tear strength ASTM D 4533
Exporter of rubber,plastic bathroom accessories needs physical laboratory for physical testing including prformance and biodegradability: 1 Tensile strength ISO 527 1 2 Elongation 3 Tear strength 4 Density / sp. gravity 5 Hardness 6 Breaking strength in fabric ASTMD 4632 7 Low temp. bending test in butyl mansjett D 2136
Chemical test for rubber, plastic components,fabric 8 Chemical composition for all type including SS & MS 9 Operating temp. ( min.& max.) 10 Perforation resistance ISO 7765 11Water proof level EN 1928B 12 Water vapour diffusion resistance coefficient DIN EN 12086 13 Adhesion to metal, plastic, wood, fabric ASTM D 1926 14 IN FLAMABILITY Test DIN41
Materials Laboratory needed for ASTM tensile testing to ASTM E8.,Standard Test Methods for Tension Testing of Metallic Materials. Flat tensile specimen will need to be machined according to ASTM E8 from 6061-T651 slug that is 2.75 in diameter and 8 in length. Material should meet the requirements of AMS QQ-A-225/8A. Please provide quote and delivery time. Thank you.
Laboratory needed for ASTM tensile testing to ASTM E8.,Standard Test Methods for Tension Testing of Metallic Materials Flat tensile specimen will need to be machined according to ASTM E8 from 6061-T651 slug that is 2.75 in diameter and 8 in length. Material should meet the requirements of AMS QQ-A-225/8A. Please provide quote and delivery time. Thank you.
Automotive laboratory needed for ASTM Testing and testing to norm MS211-47 Type A2 (KIA/HIUNDAI): ASTM D792, Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement , density, relative density, specific gravity, D638 - 14 Standard Test Method for Tensile Properties of Plastics , modulus of elasticity, percent elongation, plastics, Poisson&rsquo,s Ratio, tensile properties ASTM D790, Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials , flexural properties ASTM D256, Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics , impact resistance, Izod impact, notch sensitivity, notched . ASTM D648, Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise
URGENT Materials laboratory needed for physical and microbiology ASTM testing of tape bituminous wrapping tape used in petroleum pipelines Property Values Test method Tensile strength 12 N/mm2 BS 2782 Elongation 300 ASTM D 1000 Tear resistance >50 ASTM D1004 Adhesion to steel >2 ASTM D1000 Adhesion to Self >1.8 ASTM D 1000 Impact resistance >15J DIN30627 Dielectric strength >30000 total systemASTM D149 Insulation resistance2.5x1012 Ohm.cm ASTM D257 Water Absorption <0.1% ISO 62 Water permeability 0.01g/100inch2/24h ASTM F1249 Bacterial Growth - No Mic
Non-Destructive NDT Laboratory needed to provide a quote for the failure analysis of a failed CW pump bolts.
We require doing the following testing:
? Digital photography ? Visual examination ? Physical measurements ? Corrosion examination (Corrosion deposits) ? Fractographic examination ? Metallographic examination (Microhardness, microstructure characterization) ? Mechanical properties (Tensile and chemical analysis)
Your immediate response is highly appreciated
ISO Materials laboratory needed for ASTM PMMA panel testing to US Standards, ISO and EN standards. ASTM E90 and E413, ASTM D-638 : tensile properties, ASTM D-790 : flexural properties, ASTM D-1003 : luminous transmittance, ASTM D-635 : burninjg of plastic, ASTM D-1929 ignition temperature. We also need to do the TL-4 inside the Report 350 (crash test safety performance). Thank you so much. Regards.
Canada plastics laboratory needed for ASTM testing on tensile bars. The following tests we are interested in having done;
Izod Impact (Notched) ASTM D256 Flexural Modulus ASTM D790 Plastics Tensile Testing ASTM D638
We are interested in getting a quote for the work. We have control bars, and two treatment groups of tensile bars for comparative purposes.
India Laboratory needed for Mechanical Testing 1 Deflection temperature under load (1.80Mpa) ASTM D648 oC 2 Tensile Strength ASTM D638 M.Pa. Tensile Modulus ASTM D638 M.Pa. Elongation at break at 20 oC ASTM D638 % 3 Flexural Strength ASTM D790 M.Pa. Flexural Modulus ASTM D790 M.Pa. Our Samples will be Cured Unsaturated Polyester Resin.
University researcher needs India biomechanical laboratory for bone testing: 1) porosity 2) Mechanical test like compression and tensile.
Materials Laboratory needed for ASTM Testing of hdpe/pp woven grocery bags from used hdpe/pp woven sacks including peel testing as per ASTM F88 & F2824; creep test as per ASTM F1140 & F2054;tensile testing/hermetic seal/plastic bag/shrink wrap plastic welding etc. etc.
Mechanical Laboratory needed for Strength testing of welded eyebolts. Test to failure the tensile strength of 5/16" eyebolts with 3" diameter welded eyes. We have been asked to verify that the bolts will conform to ANCI B30.2 standard
Materials Laboratory needed for certification testing of PIR Rigid cold insulation, PIR (Polyisocynurate) foam segments are high-quality insulating materials with excellent properties and are supplied in pipe sections and slabs. Other types available on request. Standard densities are 50 (PIR), other densities are also available. PIR are used extensively on equipment and piping operating at lower temperatures in power stations, marine vessels, petrochemical plants, oil refineries etc. Specification No. Properties Standard Unit Value(for PIR) 1 Density ASTM D 1622 kg/m3 50 ± 1% 2 Compressive strength 10% deflection ASTM D 1621 kpa 300 3 Tensile Strength ASTM D 1623 kpa 280 4 Closed cell ASTM D 2856 % Min. 90 5 Thermal conductivity After 5 months of stabilization ASTM C 518 Kcal/hm° C 0.020 6 Friability (@ 10 min.) ASTM C 42
Asia materials laboratory needed for Tensile strength and water resistance testing of crab shells bioplastics
Medical Device Laboratory needed for USP Testing of sutures to USP 861: Suture- Diameter USP 871: Suture- Needle Attachment USP 881 : Surgical Suture- Tensile Strength
Physical laboratory needed for materials testing of lamination product for: Tensile & Elongation Tear Strength Surface Receptivity & Adhesion (WET & DRY) Ageing Low Temp. Flex Flex Cracking Porosity Oil Resistance Variation in Weight Weft Distortion Surface Blocking PU Weld Strength PU Hydrolysis Ozone Resistance UV Resistance
Document reference MSC70-23a1-6
India materials laboratory needed for test the parameters of HDPE,POLYPROPYLENE and ABS samples as follows 1.density 2.Melt flow index 3.Grade name(purity) 4.Tensile Elongation and flexural test 5.Melting point 6.Yield stress 7.Elastic modules kindly send the quotation as early as possible.
Asia geotechnical laboratory needed for ASTM Borehole Drilling Core testing Cerchar Abrasivity Index (CAI)-abrasiveness for cutter wear during raise boring and drilling tools (blast holes) ? Multistage Triaxial Test in rock; ? Further UCS and point load tests; ? Further tensile strength tests. ? Triaxial testing of soils sampled from road alignment (R1-R10)
Midwest materials laboratory needed for ASTM testing of multiple reinforced adhesive tape samples for tensile testing
Mechanical laboratory needed for mechanical performance testing for evaluation of mechanical failure modes on silicon-based vaginal rings. We are interested in the following mechanical tests (at least 10 samples per test): o Dimensional analysis o Hardness o Tensile strength o Elongation at break o Compression strength o Twisting during compression o Seal strength between ring-seal surface I look forward to hearing from you.
Large electronics company needs United States, Japan or Europe Physical Laboratory for ASTM D2628 neoprene testing: Physical Test for Polychloroprene(Neoprene) Elastic Joint Seal Following ASTM D2628 - Tensile Strength - Elongation - Hardness - Oven Aging - Oil Swell - Ozone Resistance - Low Temperature Stiffening - Low/High Temperature Recovery
Bergen County New Jersey physical laboratory needed for tensile strength testing of T shaped weld sample with 1" OD chromoly pipe that is .120" thick. Required tensile strength to break the pipe is calculated to be ~60,000 pounds (~100,000psi).
Mechanical Laboratory needed for ASM Testing: Tensile testing yield strength, minimum elongation at fracture
Materials Laboratory needed for testing done on steel group material. 1- Tensile test 2- Preparation of sample for Tensile test 3- Bend test 4- Preparation of sample for bend test 5- Hardness test 6- Metallography 7- Preparation of sample for Metallography 8- SEM study (per hour) 9- HIC test 10- SSCC test 11- Salt spray test (per hour)
Plastic Film manufacturer needs USA weathering laboratory for Accelerated weathering testing Tensile strength (Before and after weathering)
Large textiles company needs ISO fabric testing of a wide-ranging emergency relief goods to Attest BS tensile strength for fabric after exposure to UV and moisturizing climate simulation. Exposure in a climatic chamber under ISO 4892-2, type A, 360 hours. Followed by Tensile test under ISO 13934-1. Kindly quote your best price for above mentioned ISO standards.
Europe Accredited materials laboratory needed for fiber testing: -fibre determination and composition(%) -oil rate (%) -fibre linear density -number of crimp -fiber shortening rate due to crimp -fiber section shape -single fiber tensile strength (maximum strength,elongation upon maximum strength, rupture strength)
Asia Packaging Laboratory needed for Laboratory testing required for paper egg tray and its allowable limit for the following parameter: 1. Tensile strength 2.Compression 3. Waterproofness 4. Moisture
Russia Mechanical Laboratory needed for ASTM Testing: Tensile strength for fiber-reinforced polymer bars to possibility using this product in construction Engineering. Number of samples -5.
Mechanical Laboratory needed for mechanical testing to EN 13121-3,GRP tanks and vessels for use above ground. Design and workmanship
a. Textile Glass Content b. Unit Modulus of Tensile Elongation c. Tensile Strength at Rupture d. Inter laminar Shear Strength e. Barcol Hardness f. Short Term Creep Behavior g. Flexural Strength
as per EN 13121-3 annex D
East Coast USA Mechanical Laboratory needed for polyurethane testing with ~ 400% elongation. The testing requires an extensometer attachment to a tensile tester. each test will consume three samples. we will need between 10 to 20 test performed over a 1 month period.
Product Safety Laboratory needed for anti-retroviral testing: Intravaginal ring containing antiretroviral compounds. Condom Compatibility testing to include the following: 1. air burst pressure and volume 2. tensile strength 3. viral particle penetration
India or Middle East Mechanical Laboratory needed for mechanical testing of PQR coupon as per below details, PQR Coupon size:- 6? SCH XXS SMLS PIPE PIPE MATERIAL :- API 5L X52 APPLICABLE STANDARDS:- QP-STD R-006 rev-1 , API1104 Test Required: 1. Tensile test:- transverse tensile test as per API1104 2. Macro Examination:- Two Pieces as per QP-STD-R-006 page 15 of 36 ( attached for your reference) 3. Charpy V notch impact test to BS EN 10045:- Three sample sets for three positions as per as per QP-STD-R-006 page 15 of 36 4. CTOD Test to BS 7448: Two sets of sample at three positions as per as per QP-STD-R-006 page 16 of 36 5. All ?weld Tensile Test to BS 876 as per as per QP-STD-R-006 page 15 of 36: Two specimens
Ontario Canada A2LA or ILAC Materials Laboratory needed for ASTM Testing: Material testing of automotive fasteners. Hardness testing rockwell c and others. Thread verification, plating thickness, chemical composition of metals and coatings. Salt spray testing. Tensile and shear. Optical comparator for dimensional. Gauge calibration and Gauge R&R.
University researcher needs Materials Laboratory for polymer testing of newly synthesized 05/29/1 polymers of nanocomposites of acrylonitrile.Polymer Properties properties testing of these polymers such as density , tensile strength and tear strength.
Polymer Laboratory needed for polymer testing studies and failure analysis study: ECE (R-110 and R-67) requirement testing on several polymers and plastics used in parts we produce. The following tests include: -Compressed natural gas (CNG)/Liquefied petroleum gas (LPG) compatibility, which involves exposing a sample of a given material to pentane at a certain temperature and pressure for a period of time, observing the volume and mass change. -Resistance to dry heat, which involves exposing a sample of a given material to its operating temperature for a period of time, observing the change in tensile strength and elongation -Ozone aging, which involves exposing a sample of a given material to a specific temperature and ozone concentration for a period of time, observing if there is a "cracking" failure mode Thanks!
Plastics Laboratory needed for polypropylene testing of 6 samples of PP and I would like them tested for the following characteristics:-
1. MFI (/10 min) 2. Density g/cm3 3. Tensile strength MPa 4. Tensile elongation MPa 5. Fexural modulus Mpa
Please confirm the cost of doing these tests for the 6 samples, and please state how long it takes.
Materials laboratory needed for materials testing of composite materials: Composite Samples: Aluminium matrix alumina reinforced composites Total composite samples: 05 Test 1 Thermal expansion coefficient measurement: Thermal expansion measurement of composites by uniformly heating and cooling composites upto 773K temperature to find out the linear thermal expansion coefficient. Test 2 Thermal conductivity measurement: Measurement of thermal conductivity of composites. Test 3 Young's Modulus (Tensile Test) Stress-strain curve and Young's modulus measurement in tensile test at different temperatures up to 773K. Test 4 Scanning electron microscopic image of composites. Please provide the charges of these test.
Plastics laboratory needed for validation testing for XLHDPE and LLDPE material used in the manufacture of DEF tanks for Navistar. As described; 1. Soak 10 tensile bars of the LLDPE material (and XLPE material for a baseline) in room temperature DEF solution for 1000 hours (6 weeks), measure the stress strain curves of 10 samples not soaked as well as the 10 soaked samples and compare loss of strength and modulus. Compare the two grades of materials. This will give us an idea if we?re losing properties over time. Evaluate the risk. 2. Perform ASTM D1693 in DEF solution at room temperature instead of Igepal and measure rate of failure for the two materials (current grade and replacement grade). Please respond ASAP.
IV sets and IV extension sets manufacturer needs physical laboratory for IV testing: Tensile testing done to check the bond strength on the luer to tubing connections that we make here by a solvent bonding process.
Asia electrical laboratory needed for IEEE Testing: Electrical Heat cycle Test & IEC61238-1(2003-5) & Ageing Test & Tensile stress test
California Laboratory needed for physical testing on asphalted Kraft paper (building product)samples, 3 different basis weights on the following: DRY TENSILE STRENGTH (ASTMD828) WATER VAPOR TRANSMISSION (ASTME96 Desiccant method at 74.3) WATER RESISTANCE (ASTMD779) *ALL PER REFERENCE AC38 SECTION 3.1 & TABLE 2 acceptable to ICC-ES
Biomechanical laboratory needed for USP Testing: Biomaterial testing for properties of bio materials for sutures mechanical and biological tests as per USP standards for needles and sutures [knot pull, tensile stregth, straight pull, needle attachment, strength retention studies, penetration force, cross section, anti microbial coating test efficiency, throw test, elasticity] will provide samples and shipping.
US Plastics Laboratory needed for plastic ASTM Testing. A full package of information for HDPE material including: 1.Stress-Strain data for (tensile, compression, shear) 2.Strain rate sensitivity parameters identification 3.The graph of strains in lateral and longitudinal directions
New Jersey biophysical laboratory needed for tensile testing. Lab to tensile test sample in the 25kN range. There are two conditions: 1. The lab needs to be in NJ. 2. I would like to be present during the test.
Materials Laboratory needed for ceramic testing: F 417-87 Flexural testingMohns scale and Rockwell 45N scale for hardness testingTensile and compressive strength testingC 408 Thermal conductivity testingD 149-97A Dielectric strength testingCeramic samples will be provided for testing. Up to 4 samples can be provided for the testing. Samples will need to be returned on completion of testing.
Dental composite filling material manufacturer needs accredited laboratory for Biocompatiability Testing, PHysical Testing and EN ISO Testing EN ISO 4049:2009 standard procedure and also provide us the test result reports as they are also indicated in this standart. Test names: Polymerisation - Flexural Strength - Diametral Tensile Strength - Water Absorption - Biocompatibility? .
Dairy Manufacturer needs India Packaging Laboratory for packaging film testing to ISO 22000:2005 requirement,We need to test all our milk film and migration for PP,PET and LDPE materials at NABL accredited Lab.Henceforth we need the sutable labaratory address in india particularly in tamilnadu. External testing for milk film 1. Kinetic co eff of friction 2. Tensile strength 3. Elongation at break b)For curd cups , paneer pouch, ghee pouch, ghee bottle & smp inner layer, 1. Migration
Asia materials laboratory needed for ASTM Testing: microhardness and tensile tests 100 wires (1.0 mil diameter)per test wires are exposed to EFO process already. In other words, there are FABs and HAZ on the wire's area. I need to conduct tensile test on the necks of the wires and microhardness tests on points on the ball, neck, the HAZ part and the tail or end part of the wire. Need it ASAP
Manufacturer of Fiber reinforced plastic products like tanks, vessels, scrubbers etc. needs plastics laboratory for ASTM Testing: the coupon testing in mumbai as per our specified astm standards as mention below 1) Flexural Strength & Flexural modules- ASTM D 790 2) Tensile Modules - ASTM D 5063 3) Peel test & Lap shear test for dual laminate - BS 4994
Materials Laboratory needed for materials ASTM Testing to ASTM 695/ ASTM 638/ASTM 648/ASTM D570/ASTM D149 on HDPE sub-flooring channel or track that sits between flooring and joist. The parameters we require tested include: compressive strength, tensile strength, thermal resistance, water absorption, electrical properties, fire properties, acoustic properties, accelerated UV degradation testing, durability. Is your organisation able to assist us?
Plastics Laboratory needed for plastics testing: Basic plastics tensile testing of plastic chain lengths approximately 1 metre long. Anticipated tensile less that 8000lbs. Multiple samples to establish Average Ultimate Strength. no special handling required.
Canada materials laboratory needed for physical Testing of lighting for physical and optical properties: Hardness, specific gravity, tensile strength, tensile elongation, flexural modulus, melt index, impact strengthOptical: transmission loss, refractive index, numerical aperture
Singapore/Malaysia physical laboratory needed to provide analysis/test for the Canrig Top Drive coupling bolt as per below scope. I have checked Item : Coupling Bolt ; QTY : 1 PC SCOPE OF WORK: 1. Visual Examination 2. Macroscopic Examination 3. Microscopic Examination 4. Scanning Electron Microscopy (SEM) Examination 5. Chemical Analysis 6. Hardness Test 7. Tensile Test 8. Evaluation & Reporting
USA aerospace physical laboratory needed for Tensile fatigue testing of Ti specimens at RT,and at temp up to 1200F.
Southern California Plastics Laboratory needed for random third party testing: quality control testing of our production line for: tensile, impact, heat distortion, moisture, etc. for engineering resin
USA Plastics Laboratory needed for Fiber reinforced Plastic coupon testing 1) Glass content, wt percentage. 2) tensile strength, 3) flexural strength, 4) tensile modules, 5) flexural modules 6) peel test & lap shear test for Pvc Frp coupon.
Texas medical device laboratory needed for suture testing for the Tensile strength of four suture types (total of 160 samples)
India Plastics Laboratory needed for plastics testing: Tensile testing of cotton based fibre rainforcement plastic Breaking load,Strain & Stress at failure,%Elongation,Elastic modulus,Stress Vs Strain Plot,Load Vs Deflection Plot
Canada or USA Physical Laboratory needed for ASTM Testing of Metallic materials: Tensile test of Aluminum 5052 H32 sheet metal roll with thickness= 0.61 mm and width=42 mm. Results needed: UTS, yield strength, elongation, reduction of area, initial area, initial length, stress-strain curves, the Young's modulus, Poisson's ratio, force-displacement curves and data files. No. of specimens: 10
Plastics laboratory needed for ASTM Testing of 7-8 samples of vinyl sheet piling. Tensile strength, IZOD impact, transmissivity and equivalent permeability, heat deflection, and UV stability degradation.
Africa geology laboratory needed to conduct chercher abrasivity index tests (CAI). I would also like to have UCS, tensile strength Modulus of elasticity, permeability, cohesion and phi values for suite of medium to hard strong rocks.
Europe ISO 17025 accredited laboratory needed to be audited to become main testing centre for the following tests: - Chemical composition: ICPMS or SSOES, and Combustion test (C,S) - Tensile Test - Metallography inspection - Specific tests for wires and tubes (tubes: bending and flattening, wires: torsion, coiling, decarburization... to be discussed)
USA laboratory needed for controlled atmosphere hot rolling of graphite and graphite fluorination synthetic chemistry. Also AFM indenter, tensile, bending, hardness, yield strength,toughness- energy to rupture, ballistic testing of materials.
India textile laboratory needed for DIN Testing of nonwoven geo textil as per DIN method for the following properties
Thickness at 0.02
Thickness at 2.0 bar
Extension at break
Extension at 30% of tensile strength
Resistance against acid and alkaline solution pH 2-13
Resistance to punching
Also let us know how many
Plastics Laboratory needed for ASTM Plastic Testing of injection plastic components of PBT Valox, particulary. Fusion point, Fuid point, specific weight, hatdness, tensile strenght.
Materials Laboratory needed for Rubber Certification Testing to Density acc. to DIN EN ISO 1183-1Hardness acc. to DIN 53505 Tensile & Elongation acc. to DIN 53504 Permanent deformation acc. to PV 3307Low temperature behaviour acc. to VW 2.8.1 Electric insulation properties acc. to PV 1015Condensation atmosphere with constant humidity acc. to DIN EN ISO 6270-2I . one sample of EPDM rubber certification testing
Plastics Laboratory needed for ASTM Testing: creep analysis for a plastic material per ASTM D2990, Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics.
India Physical Laboratory needed for UL Testing: As per UL 62275 9.4 Vibration test for cable ties. 6.2.2 Tensile test from same stds.
Physical Laboratory needed for ASTM testing foam insulation for tensile strength to ASTM D1623, Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics at cryogenic temperatures (-265 F / -165 C). Can you do such testing? If so, can you provide me a rough budgetary cost to perform this testing in 3 directions on one type of foam insulation? The foam is polyisocyanurate with a density of 2.5 lbs/ft3 (40 kg/m3). The expected tensile strength is around 265 kPa (38.4 psi). The foam samples would probably need to be glued to a metal fixture for the testing since grips would be unlikely to work.
If you cannot do this type of testing, do you know of any labs that can? Thank you for your time.
Physical Laboratory needed for solar panel testing for strength of the our racking system against wind and snow load. Tensile test for racking system (including end clips, mid clips , nuts and bolts) is a good idea to prove strength of the system against wind and snow load. If it is possible, can you give me an information about Load Bearing test: 1) Qualifications and Certificates 2) Quote 3) Lead time 4) Test report 5) Option: Engineering Sign-off Our material setup is as follows: Unistrut : P5500 Bolt: 5/16-18 X 2 SOCKET CAP SCREW 18-8SS 31C200KCSS (See Catalog) Spring Nut: 5/16-18 TOP SPRING NUT 3/8? THICK ?ZINC TSN031 (See Catalog) Clamp - 46mm mid and end clamp (see Schletter Brochure and PO and ignore red boxes)
Materials laboratory needed for ASTM Testing mechanical testing to ASTM D638 Standard Test Method for Tensile Properties of Plastics. biaxial plaanr fatigue of composite materials, mo of samples:12 (almost)
Metallurgical Laboratory needed for ASTM Testing of sheet metal testing that complies with ASTM E517-00, Standard Test Method for Plastic Strain Ratio r for Sheet Metal and ASTM E646-07, Standard Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials for Aluminum and stainless steels.
Physical Laboratory needed for ASTM Testing to ASTM C1147 Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics. Tensile testing of 95 pieces of welded cpvp and pvc.
Materials Laboratory needed for ASTM Testing: Taber loss (by ASTM D3389, Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)) - Tear strength (by ASTM D624, Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers or ASTM D470 testStandard Test Method for Determining the Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method) - Tensile stress at 100% elongation (by ASTM D412 test) - Tensile strength (by ASTM D412 test, Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers-Tension) - Hardness (by ASTM D2240 test, Standard Test Method for Rubber Property-Durometer Hardness) Please let me know if you can perform these test, pricing and turn around time. We are looking to get results back this week.
India Plastics Laboratory needed for polymer testing: mechanical properties of polymer film (thin) % elongation and tensile testing of oplymer films, five samples of films. Please send the film size and thickness information.
Physical, Mechanical Laboratory needed for physical BS EN testing to BS EN 50182: ACSR Bison Type Test 1(One)sample .
1.Verification of construction 2.Stress - Strain test 3.Tensile Breaking Strength 4.Stringing Test 5.Tests on The Alu. Wires 6.Tests on Steel Wires 7.Grease mass per unit length 8. Drop point test of grease 9.CreepTest 10. Corona/RIV Tests
Texas materials laboratory needed for ASTM Testing: Eutectic melting testing, Clad Diffusion Testing, Tensile Testing,
India Materials Laboratory needed for ASTM Testing of Plastics Film, Base Wt gm/m2 Width mm Avg. Tensile Strenth (CN/25mm) Avg. Elongation at Break (%25mm) WVTR(g/m2*24h) Water Resistance (mbar) Other MD CD MD CD
Materials Laboratory needed for ASTM Testing for Facing material properties 1 Vapor Permeance ASTM E 96, Procedure A 2 Bursting Strength ASTM 774 3 Puncture Resistance ASTM C 1136 4 Tensile Strength ASTM C 1136 5 Mold Resistance ASTM C 655/ C 1338 6 Dimensional Stability ASTM D 1204 7 Emissibility ASTM E 408 8 Fire Testing ASTM E 84 9 Fire Testing BS 476
Materials laboratory needed for ASTM Testing: Facing material properties in your Laboratory . 1 Vapor Permeance ASTM E 96, Procedure A 2 Bursting Strength ASTM 774 3 Puncture Resistance ASTM C 1136 4 Tensile Strength ASTM C 1136 5 Mold Resistance ASTM C 655/ C 1338 6 Dimensional Stability ASTM D 1204 7 Emissibility ASTM E 408 8 Fire Testing ASTM E 84 9 Fire Testing BS 476
Acoustics and Plastics Laboratory needed for JIS testing to the standards methods below of a bonded plastic sheet with a tissue layer with 2mm of total thickness. * JIS K 6850 - Adhesives - Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies * JIS K 6854-3 - Adhesives - Determination of peel strength of bonded assemblies - Part 3: Adhesives -180? peel test for flexible-to-flexible bonded assemblies (T-peel test) * JIS A 1416 - Acoustics - Method for laboratory measurement of airborne sound insulation of building elements * JIS K 7215 - Testing Methods for Durometer Hardness of Plastics * JIS L 1096 - Testing methods for woven and knitted fabrics * JIS A 1405 - 1 - Acoustics - Determination f sound absorption coefficient and impedance in impedance tubes - Part 1: Method using standing wave ratio * JIS A 1405 -
US Physical Textile laboratory needed for testing of children's tights. Tensile, Burst, Tear Strength, Colorfastness to Crocking, Colorfastness to Dry-Cleaning, Colorfastness to Perspiration, Colorfastness to Non Chlorine Bleach, Pilling resistance, Random Tumble, Flammability.
Saudi arabia sealant manufacturer needs Saudi Arabia materials laboratory for materials testing : 1. Elongation test. 2. Hardness test. 3. tensile test. 4. adhesion test. 5. viscosity test.
Medical Device Preclinical, Clinical Laboratory needed for Condom-Compatibility Testing of Personal Lubricant 1) Condom Test: Compatibility Study (Lubricants), Tensile2) Condom Test: Compatibility Study (Lubricants), Air Burst3) Cytotoxicity4) Sensitization5) Irritation: Vaginal, Anal6) Systemic Toxicity
US Plastics Laboratory needed for ASTM Testing: physical properties of a plastic resin tensile, elgongation, yield, flex modulus, melt index, impact - izod preferred charpy okay, hardness (shore A) SAMPLES NEED TO BE MOLDED
Plastics Laboratory needed for Quality COntrol Testing, acrylic testing of acrylic used for the see-through tank wall of a new shark tank to be installed within a new world class aquarium under construction in the Salt Lake City area. The manufacturer is a Chinese firm providing their own quality control testing data. We would like to obtain indpendent testing results of some key material parameters to verify. We can provide samples of their acrylic. The parameters to be tested are: KEY PARAMETERS - STRENGTH, CHEMICAL RESISTANCE, CLARITY Density (D792) Modulus of Elasticity (D790) Tensile Strength (D638) Flexoral Strength (D790) Elongation at Break (D638) Impact Strength - Izod and Charpy (D256) Coefficient of Thermal Conductivity (C177) Deflection Temperature (D648) Softening Point - Venig (D1525) Coefficient of linear the
Eastern USA Mechanical Laboratory needed for ASTM mechanical, materials, chemical, electrical testing ASTM B 250, testing the resistivity and tensile strength of wire.
Singapore Mechanical Laboratory needed for ISO Testing and ASTM Testing to ISO 527-1ASTM E1461ASTM D150 Tensile Testing for: Tensile Modulus, Tensile Strength and Nominal Strain @ break
Dielectric for Dieletric constant and dielectric strength
Middle east Mechanical Laboratory needed for ASTM Testing to ASTM D3039, Tensile test & modulus of GRP laminates testing
Alberta Mechanical Laboratory needed for ASME Testing: Bends per QW 150, Tensile per QW 160, Vickers hardness per Nace MR 0175
Alberta Mechanical Laboratory neede for ASME Testing : PQR Bends per QW 150, Tensile per QW 160, Vickers hardness per Nace MR 0175
Large, multinational infrastructure company needs physical laboratory for for Crack Tip Opening Displacement Tests ( CTOD ).The testing should be in accordance with ASTM E 1290. Test temperature shall be -40ºC.
2.) S-5(Low sulfur steel for improved Through Thickness properties) and S-4 (Through Thickness Z- Direction Tensile Testing) in accordance with API 2W/2Y and Option 13 of EN 10225.
Material Type: Maximum Thickness 100mm Type PL1z EN 10225 S460G1+Q/+M EN 10225 S460G2+Q/+M API 2W Gr. 60Z API 2Y Gr. 60Z
Maximum Thickness 65 mm Type PL2z EN 10225 S355G7+N/+M EN 10225 S355G8+N/+M API 2W Gr. 50Z API 2Y Gr. 50Z
Europe Analytical Chemistry Laboratory needed for ASTM Testing: polymer rheology and physical testing Capillary rheometer, Ash, FTIR, moisture, tensile etc
Large Multinational Corporation needs Southeast USA electrical laboratory to analayze (8) 12 inch samples of overhead crane cables analyzed to see what has influenced their current state (tensile overloading, shear, Heat stress, rotation damage, stretch, abrasion, etc..)
Metallurgical Laboratory needed for Tensile testing for rebar under BS4449 and BS7777 Tenstile testing for steel reinforcement bars under cryogenic temperature up to -170degrees.
Canada FDA GLP GMP UKAS, A2LA, AAALAC physical laboratory needed for GMP Testing of Low Density Polyethylene lay flat tube, operating pressure, tensile and tear strength
Canada Plastics Laboratory needed for ASTM, BS, CS, BS, AS, DIN LDPE Testing for Mechanical properties of LDPE lay flat tube; Tube stretch limit Tensile and tear strength in both direction (N/50mm, N), operating pressure (m of water) Sample; one piece of 120cm tube
Large Chemical Company needs Texas physical laboratory for ASTM Testing and ISO Testing of polypropylene PP pellets specimens: Izod Impact, 23C Notched with Procedure A, ASTM D4101 Izod impact, Notched @ 23degC ASTM D256 Izod impact, Notched @ 23degC ISO 180 Izod impact, Notched @ -40degC ISO 180 Charpy Impact, Notched @ 23degC ISO 179 Flex Modulus, 2mm/min, 64 mm span ISO 178 Flexural Modulus at 23 C ASTM D4101 Flexural Modulus, Tangent, 1.33 mm/min, Method 1 ASTM D790 Tensile Strength, Yield @ 50 mm/min ISO R527 Tensile Strength, Yield @ 50 mm/min, Type 1 bar ASTM D638 Tensile Stress @ Yield ASTM D4101 Elongation @ Yield ASTM D4101 Elongation, Yield @ 50 mm/min ISO R527 DTUL, @ 0.45 MPa (455 kPa) ISO 75 DTUL, @ 0.45 MPa (455 kPa) ASTM D648 DTUL, @ 1.82 MPa (1820 kPa)
South Africa geotechnical laboratory needed for ASTM Testing: uniaxial compressive strength, tensile strength and shear strength of bore core samples
USA biomechanical laboratory laboratory needed for USP Testing, surgical suture tensile strength (straight tensile and knot tensile USP 881), and diameter (USP 861), 30 samples each test, non-absorbable, non-sterile
USA FDA GMP, GLP Biomechanical Laboratory needed for ASTM, ISO ball burst testing on tissue tensile strenth testing on tissue
Europe mechancial and materials laboratory needed for ASTM TEsting RTV silicone testing to ASTM 412a and ASTM 624c: 1. tensile test (ASTM412a), 30 samples 2. tear strength test (ASTM624c), 30 samples 3. scanning electromicrossope (SEM), 5 samples 4. accelarated whether aging, 90 samples 5. coloring capability 30 samples 6. peel Bond Strength, 30 samples 7. Water absorption 8. Filter diffusion test 9. patch test for allergic reaction
South Africa Geotechnical Laboratory needed for UCS testing , Indirect Tensile Strength testing (brasilian), Direct Shear testing, Slake Durablity testing, Atterburg, Californian Bearing Ratio, Particle Size distribution.
Physical Laboratory needed for ISO 8256 Tensile impact strength testing of notched specimens at +23ºC
Indiana or Illinois Physical / Mechanical Laboratory needed for tensile testing, 54 samples. Average peak strength = 10 lbs
NY Plastics Laboratory needed for ASTM Testing for tensile and elongation testing of gloves
California Mechanical Laboratory needed for AASHTO Testing, H-30 load testing of cast iron and ductile iron manhole frames, grates and covers. Tensile strength testing on test bars.
Plastics Laboratory needed for ASTM and ISO materials testing elastomer mixing, tensile tests, rheometrics, rubber process analysis, research and development
India Mechanical Laboratory needed for testing polymer for Tensile, Compression, Shear, Uniaxial cyclic at Quastatic,Shear relaxation at Quastatic -High strain rates (from Quastatic,1 S-1 and 100 S-1) at different temperatures -32 deg C,23 deg C,85 deg C
Mumbai India ASTM Packaging Laboratory needed for testing: 1. Density ASTM D7922 2. Ash content 3. MFI (230deg /2.I 6kg) ASTM D1238 4. Moisture KARL-FISHER 5. Izod impact ASTM D256A 6. Tensile Strength ASTM D638 7. Flexural Modulus ASTM D790 8. Vicat Softening Point ASTM D648 9. HDT@4.5Kg/cmI\2 ASTM D648 10. Elongation @ break @ 23deg C 11. ESCR - ASTM D1693 12 Spectro
Europe Mechanical Laboratory needed for static tensile tests and notch impact at RT and Low Temperature for FAA-Valid Material Qualification (B-Values).
Mechanical Laboratory needed for Mechanical properties testing - Mechanical resistance, young/Elastic modules,Tensile strength, Compressive strength and Poisson ratio of solar pattern glass.
BRAZIL MECHANICAL LABORATORY NEEDED FOR TESTING "ELASTOSYL R401/40 CONTROL 33932HO" FOR TENSILE STRENGTH.
Physical/Mechanical Laboratory needed for physical testing Vicat softening temperature testing, Melt flow rate testing and tensile properties of thermoplastics pipes.
Northeast US ISO, FDA GLP Mechanical Laboratory needed for ASTM Testing, mechanical testing of UHMWPE Fibers, incl.density, tensile strength, tensile modulus and elongation at break.
USA Physical Laboratory needed for ASTM Testing: Tensile testing. Mechanical, Tensile, Elastic Modulus. Adapt ASTM D638 and D882 to measure elastic modulus.
UK BS Textiles Laboratory needed for testing as per BS 5853 Flammability : cigarette & match - full Physical test for general domestic use: Martindale, Tear Strength, Tensile strength, Seam slippage, pilling, colour fastness to light, to rubbing and to water quality.
Mexico ASTM/Nadcap Metallurgical/Mechanical Laboratory needed for metallography, tensile testing
EN Materials/Mechanical Laboratory needed for testing TERRACOTTA Tiles for soluble salts, absence of blooming component, frost resistance, tensile bending strength, and color preserver in accordance to European Standard specification .
India ASTM/DIN Materials/Mechanical Laboratory needed for plastic material identification testing, filler contents, Density, tensile strength, Elongation, Melt Index, ShoreD hardness, ash content, recycled material content, flexural compressive strength.
Asia/USA Mechanical Laboratory needed for AASTHO Testing for the following parameters: Weight Grab Elongation % Grab Tensile (Lbs) Trapezoid Tear ( Lbs ) Puncture ( Lbs ) CBR Puncture AOS (mm) US sieve 40 Mullen Burst Permittivity (Sec-1) Permeability Uv Stability@500Hr
Mechanical Laboratory needed for testing a dermal scaffold used for wound repair. One requirement is the ability to hold a suture when used for abdominal repair or other stressful uses. In addition, if possible, we would like to test the tensile strength of the product as well as the tensile modulus (level of deformation).
Kansas City, MO or Kansas City, KS AWS, ASME Mechanical Laboratory needed for mechanical tensile and bend testing for welding qualification.
Ontario, Canada Mechanical Laboratory needed for testing tensile, yield, elongation and Rockwell Hardness on 3 samples of steel bars. Sample #1 - Unknown mtl. 22 cm length X 2 cm wide X 2mm thick Sample # 2 Unknown mtl. 22 cm length X 2 cm wide X 2mm thick Sample # 3 - Aluminum H 5052-34 22 cm length X 2.5 cm wide X 2mm thick Sample # 4 - Aluminum 6061 T6 22 cm length X 2.5 cm wide X 2mm thick
UK BS MATERIALS LABORATORY NEEDED FOR BS 5853 FLAMMABILITY: CIGARETTE & MATCH + FULL PHYSICAL TEST FOR GENERAL DOMESTIC USE AS FOLLOWS: MARTIN DALE ISO 12947-2 SEAM SLIPPAGE EN ISO 13936-2 TEAR STRENGHT EN ISO 13937-3 TENSILE STRENGHT ISO 13934-1 COLOUR FASTNESS TO LIGHT EN ISO 105-B02 PILLING ON MARTINDALE ISO 12945-2 COLOUR FASTNESS FOR RUBBING EN-ISO 105-X12 FASTNESS TO WATER ISO 105-E01
Physical Laboratory required for testing plastic film for DSC, Seal curves, Hot tack, Composition analysis, FTIR, Clarity, Haze, Tensile,COF
Canada Metallurgical Laboratory needed for ASTM tensile testing of 6.35mm stainless steel tubes. Need to receive raw data for of Stress-strain curves
Middle East mechanical laboratory needed for mechanical properties testing for set oilwell cement (special blend that we supply) like Youngls Modulous, PR, tensile strength etc.
US materials laboratory needed for ASTM property testing standard / method typical values evaluation of microstructure and distribution of silicon in BC Matrix SEM Density ASTM- C20 ASTM- C135 2.5 -2.6 g/cc Hardness KNOOP 1Kg KNOOP 2Kg 24-28 Gpa in Knoop 1 Kg Fracture Toughness, Klc Notched Beam ASTM C1421 5.00 MPa-m½ Flexural Strength (MOR), 200 C ASTM- F417 ASTM C1161 240-280 MPa Elastic Modulus, 200 C ASTM- C848 350-380 GPa
Poisson's Ratio, 200 C ASTM- C848 ASTM E494 0.18 -0.2 Compressive Strength, 200 C ASTM- C773 1700-1730 MPa
Tensile Modulus ASTM E494 360-390 Gpa
ASTM laboratory to conduct the following test on boron carbide made by requester. Property Testing Standard / Method Typical Values Evaluation of Microstructure and Distribution of Silicon in BC Matrix SEM Density ASTM- C20 ASTM- C135 2.5 -2.6 g/cc Hardness KNOOP 1Kg KNOOP 2Kg 24-28 Gpa in Knoop 1 Kg Fracture Toughness, Klc Notched Beam ASTM C1421 5.00 MPa-m½ Flexural Strength (MOR), 200 C ASTM- F417 ASTM C1161 240-280 MPa Elastic Modulus, 200 C ASTM- C848 350-380 GPa Poisson's Ratio, 200 C ASTM- C848 ASTM E494 0.18 -0.2 Compressive Strength, 200 C ASTM- C773 1700-1730 MPa Tensile Modulus ASTM E494 360-390 Gpa
Laboratory to test the following: Neoprene Rubber Disc Of size 435*395*29mm Test Required 1) Polymer 2) Polymer Content 3) Shore Hardness 4) Tensile Strength 5) Elongation at Break 6) Compression Set ( 24 Hrs at 100 degree C) 7) Change in properties after ageing for 70 Hrs at 100 degree C Shore Hardness Tensile Strength Elongation at Break
Asia Physical Laboratory needed for testing of Density,Water Basorbtion,Tensile Strength and elongation at breaking,tear strength,Deflection Temparature of Plastiscs under Flexural Load,Comppressive strength,Melt Flow Index,Melting Point(Tm),Thermal Conductivity (9 test method)
Textiles Laboratory needed for 100 wash industrial laundry testing on flame resistant garments. Chemcials and wash process provided. Garments will be tested for shrinkage, color change, and tensile strength at specified intervals through 100 washes.
India Physical Laboratory needed for raw material testing for plastics pvc or pet. Required testing: tear, tensile, haze, shrinkage, co- efficient(dyanamic, static).
India Physical Laboratory needed for NFC 33020 routine testing of insulation piercing connectors as per NFC 33020 standards. Mechanical tensile strength, electrical current carrying capacity, enviornmental testing (corrosion/water immersion test etc).
Asia IEC Physical Laboratory needed for testing a cast resin medium voltage insulator for Hv Frequency, Wet & Dry. Testing for impulse and power frequency and tensile strength.
California Physical Laboratory needed for tensile testing, vibration testing, impact testing, compression testing and relaxation testing of yoga mats.
China Analytical Laboratory needed for EN 1563 mechanical testing such as brinell hardness, tensile, yield strength, elongation, chary values, and microstructure. Testing ductile iron for the wind energy for ductile grade 400-18U-LT.
USA Physical, Mechnical Laboratory needed for Mechanical Testing: Tensile AND Torsion Testing required for Friction Welded Joint. I have 3 different companies supplying samples. I want to compare welds.
Physical Laboratory needed for ASTM Testing of fabric, ASTM D3776, Tear Strength ( lbs W x F) - ASTM D1424, Tensile Strength ( lbs W x F ) - ASTM D5034, Laundry Shrinkage ( W x F) - ASTM 1506, Vertical Flame - ASTM D6413, Thermal Manikin - ASTM F1930 Air Permeability - ASTM D737, ASTM 1959 - Arc Rating of Materials for Clothing
North America Physical Laboratory needed for Straight Line pull, Tensile of a rubber tarp strap at , ambient, -40 F and + 300 F,
India Physical Laboratory needed for metallurgical testing: grain structure , elongation, tensile strength, hardness , resistance of copper strip
USA ASTM Metallurgical Laboratory required to test H-13 tool steel for aluminum extrusion, Grain structures,hardness (all applicable scales), nitride thickness, yield/tensile stregnth's.
UK BS EN ISO MATERIALS/TEXTILES LABORATORY REQUIRED FOR (BS EN ISO 12947: 1999 part 2 - MARTINDALE ABRASION (2) BS EN ISO 13937-3: 2000 - TEAR STRENGTH (3) BS EN ISO 13934-1: 1999 - TENSILE STRENGTH (4) BS EN ISO 13936-2: 2004 - SEAM SLIPPAGE (5) BS EN ISO 12945 : 2000 - PILLING (6) BS EN ISO 105-B02 : 1999 - COLOUR FASTNESS TO LIGHT (7) BS EN ISO 105 - X12 - COLOUR FASTNESS TO RUBBING (8) BS EN ISO 105-E01 - COLOUR FASTNESS TO WATER) FULL PHYSICAL TEST CERTIFICATE FOR OUR QUALITY LINETTA AND BS5853 PART 1 - CIGARETTE TEST
Materials Laboratory needed to test Surface Emittance No CEN Norm Flame Spread NF EN 13501-1 Smoke Developed NF EN 13501-1 Water Vapor Transmission NF EN 12086/ NF EN 1931 Temperature/ Humidity Resistance Bleeding and Delamination NF EN ISO 11339 Pliability NF EN 13859-1 / NF EN 1109 Fungi Resistance / Ergosterol NF EN ISO 846 / NF V 18-112 Weight per unit of surface area NF EN 13859-1 Length and width NF EN 822 Thickness NF EN 823 Linear dimensions NF EN 12085 Apparent density NF EN 1602 Tensile strength parallel to faces NF EN 1608 Strength and elongation to break (roof applications) NF EN 12311-1/ NF EN 13859-1 Resistance to tearing (nail shank)NF EN 12310-1 T-peel test for flexible bonded assemblies NF EN ISO 11339 Thermal resistance (guarded hot plate) NF EN 12667 Water tightness NF EN 1928 / NF EN 13111 Dimensional stability NF EN 1
Europe ASTM Mechanical Laboratory needed for hot tensile test (acc.SR EN 10002-5:2005) 900oC 2 test bars low cycle fatigue at 900oC (acc ASTM E 606) 2 test bars, Material Steel, grades 34MnVSi5 and C70S6
Asia - Thailand Analytical Chemistry, Materials/Mechanical Laboratory required for the following tests:
3.5.1 Density, Core ISO 845/ASTM D 3574, Test A 3.5.5 Heat Aging ISO 2440/ASTM D 3574, Test K,22 h at 140 +/- 2 °C "126.96.36.199 Compression Deflection Stress Change " ISO 3386/1, 40% compression, 100 x 100 x 50 mm specimen, 100 +/- 20 mm/minute test speed, 3 specimens minimum 3.5.6 Humidity Aging (AUTOCLAVE) ISO 2440/ASTM 3574, Test J, 100 x 100 x 50 mm specimen, 5 h at 120 °C 188.8.131.52 Compression Deflection Change Stress Change Test acc. to para 184.108.40.206 220.127.116.11 Compression Set Test acc. to para 3.5.4 absolute figures 3.5.8 Fogging FLTM BO 116-03 3.5.9 Odor FLTM BO 131-01/SAE J1351 3.5.10 Ash Content ISO 247, Method B/ASTM D 1278, 800 +/- 25 °C 3.5.11 Flammability ISO 3795 3.5.12 Noise Absorption Properties ASTM C 384 3.5.1 Ag
USA or Canada Physical/Packaging Laboratory required for Oxygen Transmission Rate; Moisture Vapor; Transmission Rate; and Tensile Strength.
Russia, St. Petursburg or Moscow Analytical Chemistry and Mechanical Laboratory needed for the following testing: Chemical - C, Si, Mn, Cr, Ni, Cu, Su, P. Mechanical - Tensile Strength, Relative Elongation, Impact Strength, Yield Strength etc
USA and CANADA ASTM Materials/Physical Laboratory needed for Nitrile Examination glove physical propertyTensile Strength and Elongation ASTM D6319 ASTM D412 ASTM D573
India ASTM Physical Laboratory needed to test Ultra high molecular weight polyethylene for: Density, Tensile strength, Yield strength, Elongation, Hardness, Ash content, Izod impact
Bangalore Metallurgical Laboratory required to do Welding Tensile strength testing on Stell of 6.5MM thickness
Toronto, Canada Materials Laboratory required to do tensile strength testing of a flat tape used to pull wire through a conduit. The tape has been somewhat worn from use, and we need to know what the remaining tensile strength is after such wear.
Toronto Mechanical Laboratory needed for Rockwell Hardness Testing, material check, tensile and yield strength on fastener-type parts.
Asia or USA Materials Laboratory needed for L-P-410A or ASTMD5989 or ASTMD4066, Specific gravity & Melting point & Tensile strenght & Elongation,percent & Relative viscosity
Eastern PA Metallurgical Laboratory needed for Chemical Analysis of grate key metal for carbon, silicon, phosphorus, sulfur, molybdenum - high silicon ductile iron with molybdenum as per A536, Grade 65-45-12.
Physical Characterisics of Stoker Key metal consisting of Brinell Hardness of 240; Tensile Strength > 35,000 psig, elongation 10% max., ash softening temp of 2650 degrees F.
Southeast USA Metallurgical Laboratory needed for ASTM Tensile testing of multi-stranded wire rope cable, from a crane. Diameter is 7/8 inch.
USA Environmental Laboratory needed for ASTM Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
Germany Environmental Laboratory needed for ASTM Testing, Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
Indonesia or Singapore Materials Laboratory needed for Tensile, surface structure photomicrography, element analysis, etc.
Physical Laboratory needed for ASTM Testing: ASTM D882 (Tensile strength, Elongation and Modulus of PET sheet)& ASTM D790 (Flexural Strength and modulus for PET Sheet Materials)
ASTM D256 (Impact strength for PET Sheet)
ASTM D1003 (Light Transmission and Haze for PET sheet)
ASTM D648A-B for PET sheet
Engineering Company needs USA or Canada Physical Labratory for ASTM Testing SAUEREISEN LOW EXPANSION CEMENT # 29, TENSILE STRENGTH PER ASTM C 307-08
USA FDA GMP Biobechanical Laboratory needed for testing for Biomechanical properties of frozen human tissues, including tensile strength, creep tests, etc.
Materials Metallurgical Laboratory needed to perform the following material tests on aluminum alloys: Split-Hopkinson Pressure Bar Taylor Impact Johnson-Cook On the following alloys: 5059-H131 2519-T87 2195-BT 2139-T8 Can you suggest a contractor/vendor that can provide the following testing? Statement of Work The vendor shall provide materials, machine samples, and conduct characterization experiments on the following materials: a. Aluminum 5059-H131 b. Aluminum 2519-T87 c. Aluminum 2195-BT d. Aluminum 2139-T8 Characterization testing will include: smooth and notched (B and E notch) tensile tests (2 strain rates), Split-Hopkinson Pressure Bar (SHPB) tensile tests (2 strain rates), SHPB compression tests (2 strain rates) at room temperature and elevated temperature, torsion tests (2 strain rates), and Taylor impact tests at a minimum of 5
Canada ASTM Mechanical Laboratory needed for testing tensile strength of morter(made with sand and latex paint)- ASTM C 307-03.
Canada Materials or Physical Laboratory needed for Tensile and Density Testing of some TPU materials
Midwest USA ASTM 159-83, DIN 1686-2, and 1685-1 and EN1563:1997 Mechanical/Analytical Laboratory needed for testing Gray(class 2500-3500)and Ductile irons(65-45-12) for windmill industry. Tensile (inc. yield and elongation), Brinell,Chemical Composition, Microstructures,and Charpy on ductile 400-18U LT.
India ASTM Materials Testing Laboratory needed for: Plastics Discoloration Testing Physical Properties Testing Simulated Environmental Exposures Testing Studies Heat Deflection Testing Mechanical Properties Testing Peel Strength Testing Flexure Modulus Testing Tensile Strength Testing Elongation Testing Hardness Testing Thermal Properties Testing Solvent Resistance Testing Tensile Modulus Testing Solubles Testing Dielectric Constant Testing Deflection Testing Compression Testing Flammability Testing Ignition Testing Burning Characteristics Testing Stress / Strain Curves Oxygen Index Testing Environmental Stress Cracking Testing Gel Permeation Chromatography Testing Linear Mold Shrinkage Testing Surface Irregularities Testing Rockfield Hardness Testing Ash
India Physical Testing Laboratory needed for Materials Screeds Testing: Compressive strength, Residual Humidity, Waterproofing: Elasticity, Adhesion to substrate Adhesives: Shear Strength, Tensile Strength, Adhesion / bond & compatibility with above mentioned stones Grouts: Compressive strength, Resistance to abrasion, Water absorption, De-colorization, Stain Sealents: De-colorization, Stain tests, Shore hardness, elasticity, ultimate elongation
Eastcoast USA Metallurgical Laboratory needed to accurately tensile test fine diameter wire with an optical extensometry system.
USA Laboratory needed for Tensile testing of silicone elastomer sheets (0.03 thick) at body temperature. Based on engineering strain. Loading and unloading data required
India textiles laboratory needed for testing biodegardable fabric with the following properties : * High tensile strength ( about 7000psi or 48.2 MPa) * High flexibility ( about 1-2 GPa ) * Biodegradable ( preferably 100% ) * Cheap * Water,air-proofness * Anti-fungal/anti-microbial properties * Flame retardency preferable. The fabric can be either a novel material or if it is a composite ,then we would like to use major component of the composite as jute. We are a team based in India from the Indian Institute of Technology. This fabric will be used in making some special kind of bags. Please let us know about the procedure to go through the same and the quotations involved,the timeline and the patent issues( who owns the patent and in what percent ) The fabric should be developed such that a typical 100kg capacity gunny bag made out of
USA Metallurgical Laboratory needed for testing hardness or microhardness at different locations on a drawn stainless steel cup around 0.010" thick
Analysis for composition of the cup material (may need to remove nickel/gold plating)
If possible, tensile testing on cup material from different locations in the cup
Materials Laboratory needed for PCB material test, such as Peel strength, tensile strength ets.
Indi Clinical Laboratory needed for measurement of hair strength (preferable, as tensile strength) to evaluate the performance of our hair care products to substantiate claims.
Europe analytical chemistry laboratory needed for API Testing for Chemical composition (C, Mn, P, S, Cr, Ni, Cu, Mo, Nb, Si, Ti, V), including Carbon Equivalent (CE); - Mechanical properties for both body and welded joints (for welded pipes): - Tensile properties (tensile, yield, elongation); - Bend tests; - Charpy tests; - Metallographic examination
ISO West Africa materials laboratory needed for ASTM Testing for tensile strength,relative density,specific gravity,thermal resistance,colour and corrossion resistance tests [properties] of longspan aluminum roofing materils.
Mechanical laboratory needed for Minimum tensile strength, Minimum shear strength
Minimum torsional strength
Pull out value for different thickness of purlins
Pull over value for profile sheets of different thickness.
West Coast, USA Physical Laboratory needed for testing two 14mm combination wrenches we would like tested to determine the materials Ultimate and Yield Tensile Strength. One wrench is Crome Vanadium and one is Ti 6AL-V4 ELI.
FDA GMP Mechanical Laboratory needed for Dynamic Mechanical Analysis(DMA), Tensile Testing, Compression Testing
Canada Physical Engineering Laboratory needed for examination of some rebars that are left in site for 1.5 years corroded , we need Min 4 samples should be tested: 1.Measure cross section area, perimeter , weight per meter of bars 2. Tensile test to determine yielding and fuilure stresses of bars
Pakistan ISO 17025 Textiles Laboratory needed for Color Fastness Testing to washing and laundering (ISO 1O5 CO1: 1989) Color Fastness to washing and laundering (ISO 1O5 CO2: 1989) Color Fastness to washing and laundering (ISO 1O5 CO3: 1989) Color Fastness to Rubbing (AATCC-08 : 2005) Color Fastness to perspiration (ISO 1O5 EO4: 1994) Color Fastness to Water (ISO 1O5 EO1: 1994) Color Fastness to Sea Water (ISO 1O5 EO2: 1994) Color Fastness to Rubbing: Organic Solvents (ISO 1O5 DO2: 1993) Wrinkle Recovery of woven fabrics (AATCC-66: 2003) Tensile Strength of Fabric (strip method) (ISO-13934-1: 1999) Tear Strength (ISO-13937-2: 2000) Blend Ratio (ISO-1833, Section-10: 1977) Ends & Picks (ISO-7211-2: 1984) Color Fastness to Light (AATCC-16 Option-3: 2004) Weight of fabric (ISO-3801: 1977-E) Pilling (Martin
UK Textiles Laboratory needed for DIN 53354 Tensile Testing and 53363 Tear testing on PVC coated polyester fabric to DIN standards.
Textile laboratory needed to study the break strength and tensile strength of cotton sheeting
Textiles laboratory needed for testing to determine pick up of sized yarn, elongation and tensile strength of sized yarn
Biophysical laboratory capable of performing aging studies and tensile tests on woven collagen dressings needed. We are performing aging tests on samples of the dressings medical devices, and we wish to determine how long term elevated storage temperatures effect the elasticity and tensile strength of the matrices over time. The samples are 1/8in x 2in x 3in. We are interested in contacting with you to perform 18 stress/strain measurements, providing a stress/strain curve for each sample and corresponding analysis. Half of the the samples (9) would be ready in mid March, and the other half (9) in early April. If you are interested in contracting with us for these analyses, please contact me.
Mechanical lab needed for the ASTM creep-tensile testing of some geotextile samples using ASTM D6992.
FDA Biophysical laboratory needed for ISO tensile strength testing of tissue (tendons
Physical laboratory URGENTLY needed for ASTM testing the following materials:
3no. 350mm x 450mm x 69mm
3no. 200mm x 300mm x 52mm
3no. 200mm x 400mm x 63mm
Tests required are:
The tests are indicated in table 18.104.22.168 of Division II of AASHTO
1. Durometer Hardness as per ASTM D 2240
2. Tensile Strength as per ASTM D 412
3. Ultimate Elongation as per ASTM D 412
4. Heat Resistance as per ASTM D 573
5. Compression Set as per ASTM D 395
6. Ozone Resistance as per ASTM D 1149
7. Instantaneous Thermal Stiffness as per ASTM D 1043
8. Peel strength between rubber and reinforcement as per ASTM D 429 Method B
9. Shear modulus as per Annexure A of ASTM D 4014
Physical laboratory needed for ASTM testing of rubber tiles. Kindly provide an official quotation of testing charges to us. 1. Abrasion Testing ASTM F1292 2. Coefficient of Friction ASTM D 3389 3. Elongation At Break ASTM D412, DIE C 4. Tensile Strength ASTM D412, DIE C 5. Coefficient of Thermal Expansion 6. Flammability ASTM D2859 (Burning Pill Test) 7. Shore A Hardness ASTM D2240 8. Tear Strength ASTM D624, DIE C 9. Water Permeability 10. Weatherization Test ASTM C67&D573 11. Critical Fall Height ASTM F 1292-99
Physical Laboratory needed for ASTM tensile testing (ASTM D882, ASTM 638, ASTM D3826) on plastic polymer consisting of a mix of PE and EVA using ASTM standards.
Textile laboratory needed for apparel testing on various items, with results that report the following; shrinkage, crocking, fabric tensile strength, etc.
Electrical Laboratory needed for IEC or BS Electrical Short Circuit and Tensile Strength Testing: Cleat Type Impact Resistance Resistance to Electro Mechanical Force Temperature for Permanent Application Needle Flame Test Lateral Load Test Axial Movement Test SHORT CIRCUIT TEST
Physical laboratory needed for ASTM testing tensile strength and stress relaxation properties of various nitrile butadiene rubber products.
Materials laboratory needed for strength analysis (tensile, compressive, flexural)and testing in BS 2782 standards Tensile strength with elongation at first break. flexural strength Compressive strength
Mechanical laboratory needed for ASTM Testing for Mechanical properties of the SS sheet metal: Hardness, Tensile strength (ultimate & yield), Elongation at break, Modulus of elasticity (longitudinal & transverse).
Mechanical laboratory needed for Instron Tensile Testing - 800pcs Description: Measure Peak Tensile Force (lbf) Required to Unseat Plunger Tip (Hardened Steel) from Stainless Steel Shaft.
Fixtures: will be provided. Set-up is minimal and cycle time is as fast as one can load and unload samples and run the test profile.
Data required: force vs. distance curves and recorded peak force.
Peak Tensile Test Settings: Load Cell = 10,000 lb Initial Speed = 0.1 in/min rate Test Speed = 0.1 in/min rate Load Hi = 1200 lbf Ext Limit Hi = 20 Bk Sensitivity = 50
Powerpoint with pictures of samples and fixutes available upon request.
Materials laboratory needed for microscopic decarburization testing and tensile strength testing of boiler tubes
Multinational Manufacturer needs physical laboratory for testing each lot of fabric that we provide, assuming that you cut, prep, test the samples 3 across weight 3 across perm 3 across thickness 3 across mullen burst 3 across warp tensiles & elongation @ 50 lb 3 across fill tensiles & elongation @ 50 lb 3 across warp/fill shrinkage 3 across fabric count
Materials laboratory needed for ASTM Testing (ASTM D2990) MDPE for tensile creep testing and Flexural creep testing with two temperatures are 30 and 50 degree celsius with applied stress. but the point that I dont know how much stress the sample should be loaded?, so please clarify me with this questions. Moreover, plelase let me know about price of creep testing and for prepared sample too.
Physical laboratory needed for fully characterizing the physical and mechanical properties of a newly developed Active packaging technology: Tensile, Elongation, Modulus, COF, Imact, Puncture, Heat seal strength. Samples are a 2 mil EVA based film with our technology incorporated into it. CDA required for more detail
Materials laboratory needed for ASTM Testing, Hardness tests:ASTM D2240, 15 sec post impact at 23C Shore A Durometer Dynamic Properties: standard ASTM D5279, at 10HZ, 0.3% Amplitude Glass Transition Temperature; Max Loss Factor at 10HZ Compression set: standard ASTM D395 Method B, 22Hr at 22C; 22Hr at 70C, *50C Compression Load Deflection kpa: standard ASTM D575 at 0.51 cm/min; 10% kpa; 20% kpa; 30% kpa; compression Modulus kpa Tensile Strength kpa: standard ASTM D638; 51cm/min at 22C Tear Strength kN/m: standard ASTM D624 Temperature range C: Peak damping performance temperature range; recommended maximum intermittent temperature; Maximum continuous service temperature
Physical Laboratory needed for ANSI testing for Compression strength, Tensile strength of adhesive mortars construction materials.
Preclinical laboratory needed for preclinical testing topical of wound-healing therapeutic in experiment on animal model including surgical incision followed by suturing; possible endpoints include accelleration of time to healing, reduced inflammation and swelling, reduced scar formation, and scar tensile strength.
Physical laboratory needed for Bar Stock Shell Testing to 52000 PSI Tensile test for burst pressure.
Textiles laboratory needed for ASTM testing fabric weight per sq. yd. tensile strength tear strength
Physical laboratory needed for tensile testing new lifting lug designs that carry the weight of our products. They have their specific shape, not standart specimen shape. Test will simulate 60-degree lifting angle.
ISO Mechanical laboratory laboratory needed for ISO (ISO/PAS 17712) seal strength testing: four (4) seal strength value tests required to obtain compliance to ISO/PAS 17712. They are:. Tensile strength (pull apart force). Shear strength (cutting force). Bending strength (back and forth movement). Impact resistance (direct force on the products).
Physical laboratory needed for AWS and ABS testing of Welding Procedure Development (Bends, tensiles, Xray or UT)and Welder Qualification (Bends or XRay) Charpy impact (Weld centerline, FL, FL+2mm, and FL+5mm) temps from -20C to -60C.
Materials laboratory needed for ASTM testing of fiber reinforced polyester panel including Fire resistance test (ASTM E84); UV + humidity resistance (weathering accelerated test) ASTM D4329; Chemical resistance ASTM D543; Flexural strength ASTM D790; Tensile strength (including elongation) ASTM D638; Izod Impact ASTM D256; Water absorption ASTM 570; Coefficient of thermal expansion ASTM D696. If you think that I have missed any additional tests, or another standards which might be more suitable for my application I will appreciate your advice.
Textile laboratory needed for AATCC physical testing (tensile, tear, abrasion, etc) and performance testing (water and oil repellency, moisture management, etc).
Materials laboratory needed for engine testing: Tensile strength, Residual strain, Gas Analysis, Liner Tightness on engine blocks
Environmental and mechanical laboratory needed for Vacuum chamber testing, vibration, temperature cycling, tensile testing, temperature/humidity chamber testing
Mechanical laboratory needed for ASTM Testing Properties of FRP Plate t. 6mm should be test for Mechanical Porperties and Strength for :
1. Tensile Strength, Tensile Modulus ASTM-D 638 2. Compressive Strength, Comp. Modulus ASTM-D 695 3. Flexural Strength, Flexural Modulus: ASTM-D 790 4. Shear Strength, Shear Modulus: ASTM.? 5. Specific Gravity / Density: ASTM-D 792 6. Poisson Ratio: ASTM .?
Mechanical laboratory needed for ASTM Testing for Heat Aging to Degradation on food grade nylon films packaging - ~1.0 mil thick. I need a comparison of 2 films of time vs. temperature (to failure). I may need tensile and or puncture testing.
ISO physical laboratory needed for BS EN materials testing (BS EN 919:1995) on 48mm, 64mm and 72mm, diameter polyamide hawsers (ropes) as per BS EN 919:1995;
a. Tensile strength b. Determination of Water Repellency c. Determination of lubrication and finish content
It is requested that availability of testing facility may please be confirmed. Moreover, approximate costs and length of samples required may also be informed.
With Best Wishes M Faisal
Inspectorate of Naval Stores 6 Liaquat Barracks Karachi Pakistan Tel 922156636394 Fax922156636763
Mechanical laboratory needed for CSA ( CSA Z245.11-05)testing for tensile, hardness, guided bend, charpy impact
Physical laboratory needed for ASTM and ISO testing - Tensile Testing, Tear Testing, Ozone exposure, hydrolysis, Helium permeability, air holding, cemented seam testing, blocking, oil resistance on textiles: FED STD 191A, Mthods 5100, 5136, 5960, 5970, ASTM D1434-82, ISO 5978, ISO TR 6065
ISO Physical laboratory in Europe needed for ISO/PAS 17712 testing (bending, shearing , tensile and impact load at -27 c) of container security seals.
Physical laboratory needed for testing DMA - ABS, flex from minus 50C; DMA - plastic fibre, ambient, in submersion, till break will occur, TMA - tensile, fibre
Physical laboratory needed for testing tensile strength of automotive plastics after exposure to lubricants
Mechanical laboratory needed for tensile testing of plastics at high temperature(between 100 and 150 Degrees Celsius) with the use of an extensometer
We are interested in having a series of lab tests done on several injected polyolefin foam shoes. We would supply three samples and have each tested to compare the following: Hardness Specific gravity Tensile Strength Breaking elongation Tear strength Split tear Elasticity Compression Set Shrinkage (exposure to heat/UV) Din abrasion Flex Ross Slip resistance Can you let me know where we might get these products tested, how long it would take and the estimated cost?
Material testing on high density and low density plastic bags for size, gauge, dart impact, jog, tear, tensile, opacity
USA Textiles Laboratory needed for Thermal analysis and physical testing of filament yarnMelting temperature determination through DSC analysis, tensile testing, linear density determination.
-Weight -Shrinkage -Colour (spectro) -Colour fastness to washing 40°C -Colour fastness to sea water -Colour fastness to chlorinated water -Colour fastness to perspiration -Colour fastness to dry and wet rubbing -Colour fastness to light -Water-reppellent -Water-reppellent after 5 washes -Waterproffness -Breathability -Windproofness -Tensile strength (warp and weft) -Tear Strength -Abrasion (Martindale) -Pilling -Seam resistance (8daN) -Strap, handle, adjuster strength test -Lateral strength -Reciprocating test -Azoic detection -Formaldehyde detection -Heavy metal detection
Required testing to be done on natural and synthetic rubber gloves to include EN388, EN374, tensile, extractable protein.
Viscoelastic characterization of polymers -DMA frequency scans in the tensile mode, at multiple temperatures (about 10 temps - 5 above Tg and 5 below). The output I need is the master curve. Number of materials will be between 10-15. SOme of these materials will the stiff (E about 20GPa), and some will be soft (E about 4GPa). Also some of these materials will be in 4-5 mil thick sheets.