Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Machinery Laboratories to perform their Machinery Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Machinery laboratory that would like more information on these Machinery projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Large corporation needs mechanical laboratory for torque testing 65 mm socket wrenches with a 3/4 drive for torsional impact to be rated for impact wrench use. The torque spec for the application is 700 lb-ft, and impact wrenches used on these tools could be rated up to 1,350 lb-ft in reverse.
Automotive parts manufacturers needs laboratory for accelerated againg of test oil sa including GC-MS headspace and GC-MS direct injection (after dilution by dichloromethane) 2 test oil sa) 0 days and after 7 days heat agingb) 0 days and after 7 days heat aging and 21 days heat aging
Internationally recognized laboratories needed for benzene comparison study of fuel efficiency in engines A-80 & A-92 of gasoline imported from different countries for environmental and efficiency in engines.
Physical laboratory needed for DIN Testing of automotive parts to 5.9 Solar Radiation Test as per DIN 75220, D-OUT-F Test duration 1 cycle = 240 hrs. Test chamber temp = 42 oC, RH 65 % Radiatlon intensity 1000 W/m2 Visual evaluation 5.10 Dust Test - execution as per ISO 16750-1, resp. ISO 20653 - Preparing of the test samples; without sealing and without producing of testing 1 cycle: - Swiriing of dust in chamber for 6s - Dust deposits for 20 min - Total of 20 cycles - Type of dust: Arizona dust A2 Operation mode 3.2 for 5 min (necessary to specify operating voltage) - Evaluation - dismounting of sample and check of dust ingress (necessary to specify) - 1 sample tested in 1 load
Auto parts manufacturing company needs quarterly check of metal surface for compliance with ANSI B46.1 Standard in compliance with Rz10 requirement in (3) places on (3) Cold Rolled sheet metal parts with compound surfaces; Size of Part ranges from 120 mm diameter X 100 mm in Length.
LONG-TERM TESTING Equipment manufacturer needs laboratory for swabbing and residue testing to detect presence of pharmaceuticals, chemicals, antibiotics, and/or hormones on equipment surfaces. Looking for a reliable supplier for multiple testing requirements throughout the year.
Shipping company needs laboratory for hose bend testing of 6 hoses that need doing bending test according to EN1765 standard. Electrically discontinuous Hydrostatic tested, Vacuum tested. Oil Suction and Discharge Hose hose id:12 ID x 30' OAL working pressure Meets BS1435 EN1765,type S15 standard 150# RF Weld Neck Flange on end 1 and 150# lap Joint Floating Flange on end 2 assembly weight:1130 LBS
Industrial cleaning equipment company needs virology laboratory for Virucidal efficacy testing on Avian influenza virus (AIV),, H7N1Noroviruses, Adenovirus & Polivirus
Have to test efficacy of electrolyzed water or Hypochlorous Acid solution (ph 6.5-7, ORP 800+, FAC 200 ppm) against various viruses and notice kill time and log reduction.
Electrical Laboratory needed for Diagnostic Medical X-Ray equipment testing: Insulation Resistance test before & after Humidity condition as per BIS norms (IS 7620-1986) we are giving below the details of the tests to be carried out. 1) Humidity Test (IS 302-1979) Humidity >= 95% at 35 to 45 Deg. centigrade for 48 Hrs followed by following test. 2) Insulation Resistance Test (IS 7620-1986,6.2.1) Apply 500 VDC for 1 Minute. Insulation Resistance >=2M ohm
Electrical Home appliance manufacturer needs Microbiology Laboratory for antimicrobial efficacy testing of UV-light on sterilization. 1. Textiles inoculated bacteria is to be washed in our machine and bacteria reduction is analyzed on textiles. (UV program is to be activated) 2. Empty machine having test material that are inoculated by bacteria adhered to the surface of drum is to be tested and the test material is to be analyzed in terms of bacteria reduction. (UV program is to be activated).
antibacterial tests on washing machine? which bacteria should be tested? which standards do you follow?
ELECTRICAL CERTIFICATION LABORATORY NEEDED FOR POWER GENERATOR TESTING: EMISSION TEST, INPUT/OUTPUT TEST (WATTS - 50KVA), TORQUE/HP TESTCERTIFICATION AND ENVIRONMENTAL COMPLIANCE OF PRAE (PROCESS FOR REGENERATION AND AMPLIFICATION OF ENERGY) - GENERATOR THAT CAN EXCEED 100% EFFICIENCY.
Laboratory needed for validation testing projects on Locomotive Radiators and CACs.
1. Thermal Cycling: Full size radiator testing, which is approximately 1000 Kg. Low and high temperature water will be required at 98 degree C and at 4 degree C. Air at high pressure shall be applied above the water. Cycles are 250000.
2. Pressure Cycling: Full size radiator testing, which is approximately 1000 Kg. low and high temperature liquid will be used. High pressure air will be required at 60 psi with cycles of 250000.
3. Shaker Table: Full size radiator testing. Water will be required to circulate at 40 psig pressure.
4. Highly Accelerated Life Test: This is the process of testing product by subjecting stress, strain, temperature, pressure etc.. in excess of its normal service parameters to uncover the faults and potential mod
Materials laboratory needed for physical testing of machine part that has Sulphuric Anodization on Aluminium that require following testing.
a. Insulation of the oxide coating (Disruptive voltage test) b. Sealing quality ? to measure loss of the absorptivity of the anodic oxide coating c. Continuity of oxide coating d. Light resistance test
USA Laboratory needed for smoke testing of lamiar flow hoods to of pump hardware that need to be aerodynamic such that it does not create dead spots in a laminar flow hood. We need to tests whether it create dead spots in the laminar flow hood. This is determined using a smoke test.
Agriculture machinery company needs India agriculture laboratory for crop testing for Improving Soil Quality & Cover Crops, Agricultural Composting and Water Quality, Nutrient Management of production crops:- Vegetables, Herbs and Flowers, Tree Fruits & Nuts, Nursery Crops and Greenhouses, Biodiversity and Pest Management, Harvest and Handling.
Food Manufacturer needs food laboratory for forensic testing. A mouse was discovered in frozen block spinach and we would like a full report on the type of mouse and what is its origin and any other details on his condition (already cooked, through machinery and has broken bones etc). We are looking to find out how the mouse ended up in the bag.
USA Textile Laboratory needed for textile testing to identify if the textile damage is chemical or from machinery.
Materials Laboratory needed for research testing to test a new coating on the V blades on a corn planter to see if they will last longer than current blades on the market with no coating.
ISO Italy Food Laboratory needed for microbial analyis of ice cream and also agar once poured into dispensing machinery
Toxicology Laboratory needed for environmental and basic toxicology Testing for toxicological and ecological section of an MSDS
Sports equipment Mfg needs textiles laboratory needed for textile testing for pressure. I need to test graduated compression apparel in mmHg. If so, what is your method, machinery and cost for such services?
Dubai or UAE Mechanical Laboratory needed for ASTM, API EOLCS, and ILSAC Testing: chemical,viscosity, cold cranking, NOACK Volatility, High shear viscosity Sequence test Ball RUST TEST, EOFT, EOWTT, Homogenity & Miscibility, TEOST MHI
Pune India Mechanical Laboratory needed for cleanliness testing of catalytic converter set up to determine the cleamliness/residual dirt level of catalytic coverters . Each pipe of the caton is to be evacuated by a vacuum cleaner/vacuum pump of power 2kW keeping rest of the openings air tight except one.The dirt thus collected in the filter bag is weighed to determine the mass of the residual dirt. The particles of > 1mm size are to be separated from the dirt and counted separately.
if you are interested pl contact.
India NABL DIN ISO Electrical/Mechanical Laboratory needed for product safety testing as follows: 1) Low Voltage Directive 2006/95/EC amended from 73/23/EEC and 93/68/EEC
2) Machinery Directive 2006/42/EC amended from 98/37/EC
3) Directive of Electromagnetic Compatibility 2004/108/EC amended from 89/336/EEC Applicable standard are as follows 1. DIN VDE 0580 of 07-2000 for Electromagnetic Devices and Components
2. EN 60204-1 - General Safety, Electrical Equipment of Machines - Part 1: General requirements
3. DIN ISO 12100-1-2004-04 - Safety of Machinery - Basic terms, general design principles - Part 1 - Basic terminology, methodology
4. DIN ISO 12100-2-2004-04 - Safety of Machinery - Basic terms, general design principles - Part 2 - Technical principles