Incoming Plastics and Polymers Laboratory Testing and Scientific Research Requests

Contract Laboratory has received the following incoming Laboratory Testing and Scientific Research Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Labs to perform their Laboratory Testing and Scientific Research. If you need a Laboratory, please Submit a Laboratory Testing Request. If you need assistance or have questions email us or call toll free 1-855-377-6821.

21-02489

Plastics and Polymers

USA LABORATORY USA Laboratory needed for residue identification on a plastic part to determine its origin.

Submit Response

21-02417

Plastics and Polymers

Polymer Materials Laboratory needed for Minimum film forming temperature MFFT for polymer emulsion

Submit Response

21-02399

Plastics and Polymers

MULTIPLE TESTS INDIA LABORATORY India Materials Laboratory needed for Intrinsic Viscosity (IV) and PVC Content testing of Plastics

Submit Response

21-02397

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS USA Laboratory needed for chemical analysis of mixed plastic waste streams, in particular organic additives.

Submit Response

21-02396

Plastics and Polymers

LARGE LABORATORY PREFERRED MULTIPLE PRODUCTS MULTIPLE TESTS Large Laboratory needed for Testing the U and K value for the thermal transmittance for two different decitex woven polyester products

Submit Response

21-02374

Plastics and Polymers

USA LABORATORY MULTIPLE PRODUCTS MULTIPLE TESTS Materials Laboratory needed for ASTM proficiency testing for plastic materials in the following ASTMs: D638, D792, D429, D2240, D3767.

Submit Response

21-02361

Plastics and Polymers

Materials Laboratory needed for polymer measurements - determination of benzene content in polystyrene samples (9 samples by certified/accredited test method.

Submit Response

21-02332

Plastics and Polymers

Contract Laboratory needed for NFPA 269 test to measure HCL Gas Content when Burning for a PVC Membrane. If a different test is more suitable, please advise. Thank you,

Submit Response

21-02318

Plastics and Polymers

CANADA LABORATORY Canada Materials Laboratory needed for testing plastics additive to show there is no interference in recycling process.

Submit Response

21-02315

Plastics and Polymers

NEW PRODUCT DEVELOPMENT RESEARCH AND DEVELOPMENT Research and Development Laboratory needed for formulation of a bioplastic

Submit Response

21-02303

Plastics and Polymers

USA LABORATORY USA Laboratory needed for NFPA 269 testing on PVC fabric membranes. We need a proposal detailing the cost, turnaround time, etc. Would like the test done asap.

Submit Response

21-02279

Plastics and Polymers

Materials Laboratory for ASTM Testing of one of our materials as per ASTM D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between ?30°C and 30°C with a Vitreous Silica Dilatometer. You are kindly requested to provide us with a quotation and testing sample requirements as per your earliest.

Closed

21-02259

Plastics and Polymers

Materials Laboratory needed for Ultraviolet Transmittance testing of Acrylic Plastic Plexiglass

Closed

21-02257

Plastics and Polymers

MULTIPLE TESTS ASIA LABORATORY Asia Contract Laboratory needed for Solvent Free Polyurethane Coating testing on pipes to the following Test Standards: BS 6920-1:2014 Suitability of non-metallic materials and products for use in contact with water intended for human consumption with regard to their effect. SS 375 Suitability of non-metallic products for use in contact with water intended for human consumption with regard to their effect on the quality of the water

Submit Response

21-02229

Plastics and Polymers

Contract Laboratory needed for ISO Antiviral Testing on non-porous surfaces as per ISO 21702 Antiviral activity on plastics and other non-porous surfaces against SARS-COV-2?Please let me know if you can, thanks.

Submit Response

21-02214

Plastics and Polymers

USA LABORATORY USA Geology Laboratory needed for purity level testing on sample of Ambergris

Submit Response

21-02208

Plastics and Polymers

USA LABORATORY MULTIPLE TESTING MULTIPLE PRODUCTS Sous Vide food manufacturer needs and due to the inherent amount of plastic utilized in this process, needs USA Contract Laboratory to determine the specific recyclability level of the plastic we use for our packaging. It is a custom multi-layer plastic designed for food grade usage.

Submit Response

21-02166

Plastics and Polymers

USA LABORATORY (California Preferred) MULTIPLE TESTS Contract Laboratory needed for STYRENE and BPA testing from a part 2 epoxy resin (a 1 OZ bottle).

I would appreciate it if you could send me the quote and details.

Thank you in advance,

Martin.

Submit Response

21-02137

Plastics and Polymers

Contract Laboratory needed for CHNS elemental analysis in recycled plastics.

Submit Response

21-02132

Plastics and Polymers

NEW PRODUCT DEVELOPMENT MULTIPLE TESTS Company launching new products needs Contract Laboratory to assist in the research and development of a new high density foam for applying to fireplace chimney flues.

Submit Response

21-02114

Plastics and Polymers

NORTH AMERICA LABORATORY Plastics Manufacturer needs North America Independent Third-Party Laboratory for light transmission measurements of plastics used for containers using colorimeter and spectrophotometer.

Submit Response

21-02088

Plastics and Polymers

INDIA LABORATORY MULTIPLE TESTS India Laboratory needed for the following thermoplastic testing 1. TSM0503G Fogging test for non-metallic materials. 2. TSM0505G Smell quality of non-metallic materials.

Submit Response

21-02083

Plastics and Polymers

USA Materials Laboratory needed for ISO plastics weathering testing to ISO 4892 Methods of Exposure to Laboratory Light Sources

Submit Response

21-02082

Plastics and Polymers

Contract Test Facility needed to analyze our O-ring (elastomer) samples(1)Measuring metal-containing amount: we need to have the Ashing-ICP-OES method to measure metal-containing.(2)Plasma resistance: measure the weight loss after applying plasma envelopment.

Submit Response

21-02079

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS Advanced Technology USA Electrical Laboratory needed for IEC Testing of Resin plaques for Ball Pressure and Glow Wire Ignition test according to IEC Test Standards: IEC 60695-2-13 IEC 60695-10-2

Closed

21-02074

Plastics and Polymers

Contract Laboratory needed with facility that can store samples of polypropylene pads (30 diameter) at high (50C) and low (-20C) temperatures for a temperature study we need to do ohave anything inhouse that can do this with samples of that size.

Submit Response

21-02048

Plastics and Polymers

Contract Laboratory needed for ISO antiviral testing of film for mirror specifically against covid.

Submit Response

21-02042

Plastics and Polymers

MULTIPLE TESTS Packaging Company needs Polymer Laboratory for the following testing on PET flakes:

moisture content. Size of the flakes Impurities - metal, paper, wood, labels., etc; Moisture, Ph; Containing non-transparent plastic - OPAK;

Submit Response

21-01997

Plastics and Polymers

INDIA LABORATORY India Polymer Laboratory needed for testing on ldpe granules

Submit Response

21-01991

Plastics and Polymers

USA LABORATORY (Eastern USA Preferred) LONG-TERM TESTING (2-3 Samples/Month) MULTIPLE PRODUCTS MULTIPLE TESTS USA Contract Laboratory needed for Trace metal testing for iron content in polyurethane and polyol resins by ICP-AES.

Submit Response

21-01976

Plastics and Polymers

Contract Laboratory needed for ASTM biodegradability testing of some plastic samples, mainly TPE.

Closed

21-01956

Plastics and Polymers

Contract Physical Laboratory needed for flammability testing according standard FAR 25.853 for our material (EPP 25 (expanded polypropylene with density 25 kg/m3) made from raw material ).

Closed

21-01951

Plastics and Polymers

Third-Party Independent Laboratory needed to testify and test the recyclability of the materials to ensure plastic stream will remain uncontaminated. Could you please provide some information on what kind of testing is required, the cost, the time necessary, the amount of material needed? Thank you in advance for your help.

Submit Response

21-01926

Plastics and Polymers

MULTIPLE PRODUCTS Materials Laboratory needed for ASTM Measurement of viscoelastic materials used in damping products for the automotive, aircraft and marine industry to ASTM 756.

Closed

21-01909

Plastics and Polymers

USA LABORATORY NEW PRODUCT DEVELOPMENT New Mattress Manufacturer needs USA Consumer Products Laboratory for the following testing of foam used in mattresses: CA Tb-117, density, airflow, burn testing, drop testing.

Closed

21-01907

Plastics and Polymers

MULTIPLE TESTING Polymer Materials Laboratory needed for Polycarbonate material testing for transimisivity of visible and near IR spectrum. My wavelength of interest are 300 to 1200 nm or 1000 nm (what ever the capabilities of your lab). The expectation is after the test we will have a good grasp and a report showing the transmisivity for visible and near infrared spectrum.

Closed

21-01881

Plastics and Polymers

Consumer Products Laboratory needed for safety, structural integrity and durability testing for a heel part made out of bio-based material.

Closed

21-01866

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for cellular plastic foam testing according to the details below:

- raw composition of the foam (100% polyurethane) according to standard ASTM D 5226 or burning method (or other equivalent standard), - foam thickness (3-4 mm), according to standard ISO 1923 (or other equivalent standard,) - foam density (48-52 kg/m3) according to EN ISO 845 (or other equivalent standard).

Closed

21-01858

Plastics and Polymers

MULTIPLE TESTS Contract Laboratory needed for the following tests on PVC Pipe: Size: 400mm dia Thickness: 20mm Tests Required: 1. Short-term hydrostatic pressure test(ISO 1167) 2. Resistance to Acetone (BS 3505:1968) 3. Impact Test(ISO 3127) 4. Density(Sp. Gravity)

Closed

21-01839

Plastics and Polymers

MULTIPLE TESTS Contract Laboratory needed for resin and a plastic film samples testing for Slip/erucamide content

Closed

21-01838

Plastics and Polymers

Materials Laboratory needed for Polymer ASTM Accelerated Aging in 100% oxygen environment to ASTM G114 Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service.

Closed

21-01766

Plastics and Polymers

MULTIPLE TESTS Polymer Laboratory needed for ASTM Fibre-reinforced plastic FRP evaluation testing for Degree of cure by DSC and also for Residual styrene by GC.

Closed

21-01748

Plastics and Polymers

Contract Laboratory needed for antiviral activity testing of plastic plates to Test method: ISO21702 [Measurement of antiviral activity on plastics and other non-porous surfaces] Virus strain: Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) Sample: Plastic plate

Closed

21-01713

Plastics and Polymers

Contract Materials Laboratory needed for Cryogenic grade Polyisocyanurate PIR Testing .

Closed

21-01692

Plastics and Polymers

CANADA LABORATORY (Ontario Preferred) MULTIPLE TESTING

Canada Materials Laboratory needed for the following ASTM Testing of Sheet molding compound SMC fiberglass 12 c 12 plate parts (20 each):

Flexural Properties per ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

Tensile Properties per ASTM D638 Standard Test Method for Tensile Properties of Plastics

Specific Gravity per ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

Closed

21-01669

Plastics and Polymers

Polymer Laboratory needed for chemical analysis of the constituents of an unsaturated polyester resin, styrene based

Closed

21-01623

Plastics and Polymers

NEW PRODUCT DEVELOPMENT USA LABORATORY USA Laboratory needed for testing new polymeric foam material with applications in footwear insoles. I wanted to perform comparison study with other insoles and the essential/ common industry tests for insoles including abrasion test, compression set, vibration/ shock absorptions etc.

Closed

21-01612

Plastics and Polymers

Contract Laboratory with the capability to to superheat water to >160 degrees cel. needed to conduct experiment to determine if superheated water can convert polypropylene fabric to liquid to separate it from other polymers (with a higher melting temp).

Closed

21-01583

Plastics and Polymers

Automotive Laboratory needed fo perform a validation study for some injected plastic samples for automotive industry according to VW_50185 ?

Closed

21-01580

Plastics and Polymers

MULTIPLE TESTS MULTIPLE PRODUCTS Medical Company needs Bioanalytical Laboratory needed for Characterization of Poly Lactic-co-Glycolic Acid PLGA nanoparticle diameter, size distribution, zeta potential.Methods should include a microscopic method (SEM and or TEM) and dynamic light scattering.

Closed

21-01558

Plastics and Polymers

MULTIPLE TESTS Material Laboratory needed to perform the following tests on an elastomer: 1) NORSOK Life Estimation The test medium has would contain a slight percentage of H2S.

Closed

21-01555

Plastics and Polymers

INDIA LABORATORY MULTIPLE TESTING India Polymer Laboratory needed for Expanded Polyethylene foam EPE Foam Testing

Closed

21-01554

Plastics and Polymers

USA LABORATORY MULTIPLE TESTING MULTIPLE PRODUCTS USA Polymer Laboratory needed for recycled pellets and HDPE testing for 2 measurements. According to US21CFR FDA part177.1520 clause c 2.1 on Polyethylene they would need maximum extraction fraction and maximum soluble fraction. As I researched that theme, I came to the conclusion that the test should be performed according to Norm D5227-13 and D3797. 

Closed

21-01536

Plastics and Polymers

UNITED KINGDOM LABORATORY MULTIPLE TESTS UK Materials Laboratory needed for testing plastic sample(s) to supplied data sheet with parameters.

Closed

21-01535

Plastics and Polymers

USA LABORATORY USA Contract Laboratory needed for research studies on plant-based alternative to leather related to biodegradability and sustainability to look at the identification of products produced by biodegradation.

Closed

21-01527

Plastics and Polymers

Differential Scanning Analysis DSC testing of plastic material according to the following test method: a) Cut a section weighing about 12 mg, and place it in the test-specimen pan. b) Determine the thermogram under nitrogen at temperatures between 40°C and 200°C at a heating rate between 2°C and 10°C per minute followed by cooling at a rate between 2°C and 10°C per minute to 40°C. c) The thermogram of the specimen is similar to the thermogram of USP High-density Polyethylene RS, similarly determined, and the temperatures of the endotherms and exotherms in the thermogram of the specimen do not differ from those of the standard by more than 6.0°C.

Closed

21-01495

Plastics and Polymers

USA LABORATORY Packaging Company needs USA Materials Laboratory for oxygen transmission rate testing of barrier film.

Closed

21-01485

Plastics and Polymers

EUROPE LABORATORY MULTIPLE PRODUCTS MULTIPLE TESTS Europe Contract Laboratory needed for ISO testing of antibacterial and antiviral master batches that will be used in films and fleeces or other plastic materials against the virus Sars Cov2 according to ISO 21702 / ISO 18184. Ideally, we need information of the following time frames: viral activity after 2 min, 15 min, 30 min, 2h and 24h.

Could you please send us an offer? Please include the price for single intervalls, as we might lower the number of test if needed. How much sample do you need per test? How long should we expect until we receive any results? Thank you and best regards

Closed

21-01449

Plastics and Polymers

INDIA LABORATORY MULTIPLE PRODUCTS India Contract Laboratory needed for UL Testing in compliance with UL 94 Standard for Safety of Flammability of Plastic Materials for Parts in Devices and Appliances testing,

Closed

21-01447

Plastics and Polymers

EUROPE LABORATORY MULTIPLE TESTS Europe Contract Laboratory needed for the following PET FLAKES CLEAR & LIGHT BLUE & MIXED COLOUR testing: Fines content < 0.5 mm % Oversize flakes content >12 mm % Dimensions mm Intrinsic Viscosity IV dl/g Moisture % Dust concentration % Ph Inflammability Point °C Melting contaminants Polyvinyl Chloride (PVC) ppm Polyolefins (PP, PE) ppm Other plastics (PA, MXD6, PC, etc.) ppm Flakes opaque ppm APET/PE flakes ppm Other multi-layer flakes (with PA, EVOH) ppm Flakes with glue residue ppm

Non-melting contaminants Metal ppm Paper and wood fibers ppm Other contaminants (particulates) ppm

Detectability for recycling NIR detectable ppm Carbon Black content ppm

Closed

21-01409

Plastics and Polymers

UK LABORATORY (Preferably Lancashire) UK Laboratory needed for Ambergris confirmation testing. thank you

Closed

21-01380

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS USA Contract Analytical Laboratory needed for cyclic silicones testing (i.e. cyclotetrasiloxane, cyclopentasiloxane, cyclohexasiloxane) by GC-MS in a silicone mixture.

Closed

21-01371

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS USA Contract Laboratory needed for ASTM and ISO Particle size distribution of polymer microparticles measured using laser diffraction

Closed

21-01356

Plastics and Polymers

Contract Laboratory needed for ISO antiviral activity testing of cotton sample with mercury ions embedded in it. Mercury ions form rigid bonds with polymer molecules. The sample is active against a wide range of bacteria.

Closed

21-01353

Plastics and Polymers

NEW PRODUCT DEVELOPMENT MULTIPLE TESTS Contract Laboratory needed for Test Method Set-Up and Validation of various tests for a new transparent and stretchable PVC plastic film for food packaging, such as meats, fruits and cold cuts, and for surface protection is able to inactivate the new coronavirus.

Method set-up and validation for analysis on Human coronavirus

HCov 229E according to ISO 21702

* To be performed only once

Antiviral activity test on plastic and hard non porous surfaces according to standard ISO 21702:2019

Protocol:

- 1 Virus: Human coronavirus HCov 229E

- 1 contact time

- The protocol includes all method validations and control specimens

Deliverables: final report

Or a similar test that I get the approval from TGA.

Closed

21-01323

Plastics and Polymers

USA LABORATORY RESEARCH AND DEVELOPMENT Polymer Research Laboratory needed to conduct experiments on Polyurethane rubber filling with biodegradable fillers with the goal to develop a more sustainable material for show soles and other similar applications. Also, PVC and EVA systems would be interesting to explore.

Closed

21-01302

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for conducting the following American Petroleum Institute API tests on 2 elastomeric samples according to API 6A ED. 21Specification for Wellhead and Christmas Tree Equipment

- SOUR FLUID IMMERSION TEST OF ELASTOMERIC MATERIALS ACCORDING TO API 6A ED. 21 CHAPTEL F.1.13.5.2 dell'Annex F.

- TEST FLUID MATERIALS CLASS FF/HH

- TEMPERATURE EXECUTION OF, 150°C. DURING TEST TEMPERATURE CANNOT BE LESS THAN 150°C.

- PERIOD 160 HRS (AS PER STD)

- REPLICATION, NO. 5.

Looking forward to hearing from you.

Closed

21-01277

Plastics and Polymers

USA Packaging Laboratory needed for USP testings for pharmaceutical packaging material to .USP 661.1, 661.2, 671 Plastic Packaging Please provide me the quotation and lead time.

Closed

21-01233

Plastics and Polymers

Pharma Company needs Pharmaceutical Laboratory for Method development for polymeric anti-foam agent quantification in complex a product stream obtained from a fermentation process.Quantification of polymeric anti-foam to low ppm levels GC-MS preferably, but recommendations for other suitable methods welcomed

Closed

21-01229

Plastics and Polymers

MULTIPLE TESTS Contract Laboratory needed for high impact, high and low temperature testing of a panel which is a combination of Glass Reinforced Plastic polyurethane foam. We would like to test for high impact, high and low temperature. Kindly advise if your side can do this service.Thank you.

Closed

21-01142

Plastics and Polymers

Pharmaceutical Company needs North America Packaging Health Canada compliant child-resistant mylar bag packaging testing to Canadian standards (CSA Z76.1 & Z76.2). Our bags already meet 16 CFR 1700, but require higher certification.

Please provide any info in regards to cost, how many samples you require, turnaround time and what certifications you can test and certify for.

Closed

21-01127

Plastics and Polymers

Aerospace Materials Laboratory needed for FTMS Testing of 15 MIL Urethane material to FTMS 191, Method 5460 for TSO submission to the FAA.

Closed

21-01124

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS Existing Wal-Mart Vendor has more orders of plastics granules that they need Materials Laboratory for Certificate of Analysis COA Testing

Closed

21-01101

Plastics and Polymers

Large Oil Company needs Laboratory to help explore ways to evaluate composite (i.e. reinforced polymer with glass fibres) pipes. The samples are expected be in a pipe shape. Are you able to machine to the standard dimensions? If so, how much sample is required for each of the tests below?Are you able to age (e.g. one week in an oven) the samples then conduct tests on the virgin and the aged samples?Are you able to modify ASTM test conditions (e.g. temperature and test duration)?Roughly, how much does each of the tests below cost?

Closed

21-01085

Plastics and Polymers

Construction Materials Laboratory needed for testing to upgrade the classification of PVC ceilings from D class acoustic. to acoustic class to A class.

Closed

21-01081

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS Contract Laboratory needed for antimicrobial and antiviral effectiveness testing of polyester adhesive films on a variety of hard surfaces such as table tops, windows, etc.

Closed

21-01078

Plastics and Polymers

INDIA LABORATORY MULTIPLE TESTS MULTIPLE PRODUCTS India Contract Laboratory needed for Biodegradability Testing of Plastic materials to the following Test Standards: EN13432 / ASTM D6400 ASTM D5511 / ISO 15985 ASTM D5338 / ISO 14855

Closed

21-01024

Plastics and Polymers

NEW PRODUCT DEVELOPMENT Packaging company needed for FDA Title 21 Food Contact Certification Testing of a new plastic injection molded , modified PBS resin bioplastic finished good container meant for food storage.

Closed

21-01006

Plastics and Polymers

EUROPE OR USA LABORATORY MULTIPLE TESTS MULTIPLE PRODUCTS

Europe or USA Contract Materials Laboratory needed for rheometric testing services of rubber mixtures . Below I detail the type of tests we need: Minimum test required:Rheometry at a temperature of 150ºC for 20 min: following the ASTM D5289 standard; If possible, perform:Mooney viscosity: following the ASTM D1646 standard; Sample quantity: 3 different batches. Please send us a quote for this type of test.

Closed

21-00971

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS USA Contract Laboratory needed for adhesion testing service for a foam pad including peel, shear and adhesion. Need testing within the week

Closed

21-00891

Plastics and Polymers

USA Contract Laboratory needed for bomb calorimetry testing to measure calorific values (kJ/kg) for fire safety purposes.

Closed

21-00811

Plastics and Polymers

Contract Research Organization needed to conduct several studies of microwave technology chemical processes used convert mixed plastics waste into new products. Through these process, we are making paraffin wax that we need to purify to recover specific product cuts without degrading them. We have done extensive work on this several years ago and short path distillation worked well.We will generate lab-scale samples (wax/oil) during the next year. We are also interested in having you perform some composition analysis of the products. The objective will be to scale-up the process within a timeline of 2-3 years at which time we would generate more products for purification and we will need to scale-up the purification process as well.

Could you offer us a service for performing short path distillation on the products (at lab-scale for n

Closed

21-00807

Plastics and Polymers

MULTIPLE TESTING Polymer Laboratory needed for polypropylene resins conditions of use and under the criteria 21 CFR § 177.1520 (Olefin polymers (a) (1) (i), (a) (3) (i), (b), (c) (1) and (c ) Specifications: 1.1a and 3.1a.)

We also need to determine the Conditions of Use in which our polypropylenes can be used in accordance with Table 2 of 21 CFR § 176.170 (c).

Closed

21-00790

Plastics and Polymers

USA Contract Analytical Laboratory needed for VOC testing on packaging foam samples. TD tube testing for the following flurinated, siloxanes, esters, bases phenolic/alchol, aldehyde/keytones, aromatics, aliphatics, plasticizers, heterocycles, sulfurous.

Closed

21-00757

Plastics and Polymers

Contract Laboratory needed that can evaluate the effects of a UV Spray on top of polypropylene PP packaging.

Closed

21-00752

Plastics and Polymers

Contract Laboratory needed for ASTM biodegradation testing as per ASTM D55112. 1. Is it possible to proceed Test with ASTM D55112. If it's possible, how long can we test about our sample? and How does it cost per duration of test? (We're hoping to set Test duration between 500days ~ 2 years )

Closed

21-00735

Plastics and Polymers

Contract Materials Laboratory needed for ASTM Testing for NCO content as per ASTM D2572-19 Standard Test Method for Isocyanate Groups in Urethane Materials or Prepolymers

Closed

21-00717

Plastics and Polymers

MULTIPLE TESTS Oil Laboratory needed for testing polymer oil sample for parameters PIONA-Paraffin, Isoparaffin, Olefin, Napthene and Aromatic parameters. Please send your quote for the same.

Submit Response

21-00695

Plastics and Polymers

Large Corporation needs Contract Laboratory to evaluate a plastic housing which developed cracks in the screw bosses during assembly. Specifically we want to know if the plastic has been degraded resulting in the high (~20% failure rate) during the assembly process. The housing is approximately 8 inches by 6 inches by 5 inches, and we have three samples.

Closed

21-00668

Plastics and Polymers

Materials Laboratory needed for ISO elastomer testing to ISO 2782 Rubber, vulcanized or thermoplastic ? Determination of permeability to gases ? Part 1: Differential-pressure methods

Closed

21-00649

Plastics and Polymers

ISO 17025 Accredited Materials Laboratory needed for ISO UV testing according to for 1000 hours exposure. for 40 samples of plastic materials to ISO 4892-2 Plastics ? Methods of exposure to laboratory light sources ? Part 2: Xenon-arc lamps

Closed

21-00593

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS USA Polymers Laboratory needed for testing molecule in various polymer reactions to gauge our molecule's ability to improve or increase cross-linking. This laboratory should be able to run reactions with and without our molecule and compare product properties regarding improved cross linking.

Closed

21-00554

Plastics and Polymers

MULTIPLE PRODUCTS Polymer Materials Laboratory needed for film testing for oxygen transmission rate and water vapor rate.

Closed

21-00550

Plastics and Polymers

MULTIPLE PRODUCTS Packaging Laboratory needed for durability testing on inventory of packaging materials: Rolls of PVC and aluminum foil for making blisters; individual plastic bottles and lids .

Closed

21-00529

Plastics and Polymers

CONSTRUCTION MATERIALS LABORATORY NEEDED FOR TESTING LAMINATE FLOOR FOR HAZARDOUS MATERIAL OR CHEMICAL TESTING

Closed

21-00505

Plastics and Polymers

Independent Third-Party Laboratory needed for polypropylene PP melt-blown cloth with copper-oxide ingredient. We would like to test it against SARS-CoV-2 virus to see how long it takes to de-activate such virus.

The test should be carried out by comparing the virus de-activation effect in 1, 10, 30 and 60 minutes respectively between normal melt-blown cloth and copper-oxide melt-blown cloth.

Submit Response

21-00455

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS Medical Device Laboratory needed for testing our parts and materials for suitability to use various orthotic and prosthetic devices.

Closed

21-00449

Plastics and Polymers

INDIA LABORATORY BUDGET APPROVED MULTIPLE TESTS Large Chemical Company needs Industrial Contract Laboratory for isocyanate testing to the following ASTM Test Standards: (1) NCO% of Isocyanate, ASTM D2572-19 (2) Viscosity of Isocyanate, ASTM D4889-21 (3) Hydrolyzable chlorine contents of Isocyanate, ASTM D4663-20 (4) Total chlorine of Isocyanate, ASTM D4661-18

So, request you to kindly provide the test cost and lead time for the same if it is feasible at your end.

Closed

21-00441

Plastics and Polymers

USA Packaging Laboratory needed for oxygen transmission rate OTR testing for various packaging materials such as HDPE bottle.

Closed

21-00431

Plastics and Polymers

MULTIPLE PRODUCTS Contract Laboratory needed to measure alpha particle for certain materials like NiV film sheet,

Closed

21-00417

Plastics and Polymers

Polymer Materials Laboratory needed for elastic modulus of at very low strains (e.g. at forces ~= 200 uN) of thermoplastic polymer (polydimethylsiloxane) preferably with uN level force accuracy by high precision tensile testing or nanoindentation should work fine.

Closed

21-00407

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for fire behavior properties of unsaturated polyester resins. The necessary tests are: - Determination of oxygen index - ISO 4589-2 - Fire behavior of building materials and elements - DIN 4102-1

Closed

21-00404

Plastics and Polymers

ASIA LABORATORY Materials Laboratory needed for ASTM D5511 testing for NBR latex films.

Closed

21-00397

Plastics and Polymers

CANADA LABORATORY Canada Contract Laboratory needed for deformulation and reverse engineering of a coating material that is organic, and right now in solid form.

Closed

21-00393

Plastics and Polymers

USA LABORATORY (Southeast USA) Southeast USA Analytical Chemistry Laboratory for ASTM Flash point testing of organic liquid to ASTM D56 Standard Test Method for Flash Point by Tag Closed Cup Tester

Closed

21-00382

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS Materials Laboratory needed for the following testing on foam automotive parts testing: Impedance [Ns/m3] Absorption coefficient [-] Matrix E-modulus [N/m2] Matrix Poisson ratio [-] Matrix density [kg/m3] Matrix loss factor [- AFR (Acoustic Flow Resistivity) [Ns/m4] Porosity [-] Tortuosity [-] Characteristic thermal length [m] Characteristic viscous length [m]

Closed

21-00378

Plastics and Polymers

USA LABORATORY USA Materials Laboratory needed for Polymer Testing for the water extraction condition as per TSM0505G-2A for the following resins.

1. Encom 1812U 2. Encom 1812 BK4005

Please send quote and sample requirements.

Thanks!

Closed

21-00319

Plastics and Polymers

MULTIPLE TESTS MULTIPLE PRODUCTS Nanotechnoloy Contract Research Laboratory needed for experiments synthesizing nanoparticles and textile coating (mostly polyurethane) to innovate new products and services with novel features.

Closed

21-00315

Plastics and Polymers

MULTIPLE TESTING

Industrial Contract Laboratory needed for rubber compounding with natural materials (eg starch, wood pulps, oils, etc). and then compostability testing to ASTM D6400 compostability standard.

Closed

21-00313

Plastics and Polymers

BUDGET APPROVED ($2,500) Plastic Company needs Materials Laboratory for MIL STD detrimental material analysis of 3.000 Diameter Natural Nylon Extruded Rod to MIL STD 2041 CONTROL OF DETRIMENTAL MATERIALS

Closed

21-00301

Plastics and Polymers

ACOUSTICS LABORATORY NEEDED TO TEST A SOUND ABSORBING FIBERGLASS CLOTH COVERED AWEDGE BY ASTM IMPEDENCE TUBE TEST METHOD ASTM-C 384-90a

Closed

21-00286

Plastics and Polymers

North America Polymer Laboratory needed for Research and development Studies related to the formulation and sample making of flexible polyurethane foams (micro-cellular, high resiliency, viscoelastic, etc.) using our unique diols and polyols. Testing of produced foams according to ASTM D3574 - Standard Test Methods for Flexible Cellular Materials-Slab, Bonded, and Molded Urethane Foams

Closed

21-00284

Plastics and Polymers

USA Contract Laboratory needed for TVA dissolution testing of polyurethane coated urea for its release rate or release duration.

Closed

21-00271

Plastics and Polymers

Food Laboratory needed for ASTM WVTR testing on laminated film used for food packaging material including water vapour transmission rate testing as to ASTM F-1249.

Closed

21-00261

Plastics and Polymers

USA Material Laboratory needed for ASTM polypropylene felt materials testing to ASTM F726-81.

Closed

21-00259

Plastics and Polymers

Polymer Laboratory needed for polypropylene testing.

Closed

21-00240

Plastics and Polymers

Contract Laboratory needed for ISO anti-viral testing of PVC floorings as per ISO 21702 ISO 21702 - Measurement of antiviral activity on plastics and other non-porous surfaces. (Viral strain: Human Coronavirus 229E)

Closed

21-00232

Plastics and Polymers

USA LABORATORY LONG-TERM TESTING Corporation needs USA 3rd party laboratory that provide round robin testing services in order to evaluate their accuracy and precision in testing Plastic polymers ( HDPE , LLDPE , PP ) Thank you

Closed

21-00205

Plastics and Polymers

MULTIPE PRODUCTS MULTIPLE TESTS Materials Laboratory needed for polyols evaluation in terms of performance with other petrochemicals in rigid -, soft - and PIR foams. Our polyols are derived from lignin. However, to get the best market acceptance, we realize that these polyols will have to be tested in combination with other petrochemical derived polyols.

Closed

21-00188

Plastics and Polymers

USA LABORATORY Large Outdoors Company needs Physical Laboratory for ISO filter pressure value testing according to ISO 23900-5:2015 Pigments and extenders ? Methods of dispersion and assessment of dispersibility in plastics ? Part 5: Determination by filter pressure value test

Closed

21-00183

Plastics and Polymers

USA LABORATORY MULTIPLE PRODUCTS USA Contract Laboratory needed for 'CLO value' of foams/foams incorporated in garments/outdoor gear.

Closed

21-00156

Plastics and Polymers

USA LABORATORY LONG-TERM TESTING MULTIPLE PRODUCTS USA Pharmaceutical Packaging Laboratory needed for for USP testing of pharmaceutical plastic to USP 661 Plastic Packaging

Closed

21-00102

Plastics and Polymers

INDIA LABORATORY India Laboratory needed for direct microscopic examination of fungus on leather , polyurethane and rubber products.

Closed

21-00064

Plastics and Polymers

INDIA LABORATORY India Materials Laboratory needed for Oxygen Transmission Rate (OTR) for PE Polyethylene Liner. Please send quotes.

Closed

21-00056

Plastics and Polymers

Construction Materials Laboratory needed for Acrylic Elastomeric Exterior waterproof coating testing or multiple properties to multiple test standards:

Wall Coat Testing Properties Sr. No Properties Specification Method 1 Elongation at break(250 micron DFT) % ASTM D412 - 02 2 Water Permeability - Reduction in water penetration @5 bar pressure (%) BS EN 12390 3 Rapid Chloride Penetration Test -Penetration of Chloride ion ASTM C 1202-97 4 Algaue & Fungal Resistance SS 345:1998 5 Accelerated weathering (1000 hrsUV exposure) ASTM D 4587 6 Tensile Strength, N/mm2 ASTM D 412-02 7 Crack bridging ability ASTM C 836 8 Adhesion strength 9 Coverage (without dilution apply 2 coat by brush at a time of 5-6 hrs)

Roofcoat Test Sr. No Properties Specification Method 1 Solid Content % TGA/DTA Analizer 2 Elongation at

Closed

21-00035

Plastics and Polymers

Medical Device Company needs Microbiology Laboratory needed for ISO antimicrobial testing on C. diff spores on a roll of plastic liners impregnated with an antimicrobial. The plastic needs to be tested based upon ISO 22196. The test must be done over 6 periods of time (1 hour, 3 hours, 6 hours, 12 hours, 18 hours, and 24 hours).

Closed

21-00004

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for conducting several tests on Acrylic Elastomeric Exterior waterproof coating Kindly confirm this Test will be perform in your Lab and cost of each test below Sr. No Properties Specification Method 1 Elongation (250 micron DFT) % ASTM D412 - 02 2 Water Permeability - Reduction in water penetration @5 bar pressure (%) BS EN 12390 3 Rapid Chloride Penetration Test -Penetration of Chloride ion ASTM C 1202-97 4 Algaue & Fungal Resistance SS 345:1998 5 Accelerated weathering (1000 hrsUV exposure) ASTM D 4587 6 Tensile Strength, N/mm2 ASTM D 412-02 7 Crack bridging ability ASTM C 836 8 Adhesion strength 9 Coverage ( without dilution apply 2 coat by brush at a time of 5-6 hrs)

Closed

20-03338

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS USA Materials Laboratory needed to perform the following tests on Polyisocyanaurate material: Tensile strength, Linear thermal expansion, E-modulus on (-) 165 Deg C.

Closed

20-03299

Plastics and Polymers

EUROPE, ASIA OR USA LABORATORY URGENT Chemical Company developing anti-microbial film needs ISO/IEC 17025 Accredited Microbiology Laboratory for ISO 21702 antiviral effectiveness testing of film against SARS-CoV-2 (COIVD19). We ask if the virus test is possible, and we ask you to reply to what the test period and cost are. In addition, we ask if your laboratory is an ISO/IEC 17025 accredited laboratory.

Best Regards, JY Shim

Closed

20-03279

Plastics and Polymers

USA LABORATORY (Northeast) Manufacturer needs Northeast USA Materials Laboratory to ensure their is no off gassing in materials of antiviral face covering that is made of two polymers fused together at 240 degrees to make copolymer.

Closed

20-03243

Plastics and Polymers

Materials Laboratory needed for Gel fraction determination - crosslink level testing of PE Foam.

Closed

20-03238

Plastics and Polymers

Materials Laboratory needed for ASTM testing of polymers to determine their Oxygen index according to ASTM method D2863.

Closed

20-03198

Plastics and Polymers

INDIA LABORATORY India Contract Laboratory needed for ISO antiviral activity of plastics to ISO 21702-2019 Measurement of antiviral activity on plastics and other non-porous surfaces protocol?

Closed

20-03191

Plastics and Polymers

USA LABORATORY USA Agriculture Laboratory needed for Oxygen Transmission Rate of Silage Plastics

Closed

20-03176

Plastics and Polymers

USA LABORATORY (Southwest Preferred) USA Materials Laboratory needed for conventional GPC analysis of 4 general purpose polystyrene samples. - Molecular weight data should be down to 1000 and 5000 g/mole or Daltons {units} - What is typical turn around time for samples? - What is the charge per sample? - Can you provide molecular numbers and the raw data in Excel?spreadsheets.

Closed

20-03149

Plastics and Polymers

USA Consumer Products Laboratory needed for LHAMA ASTM D-4236 testing of thermoplastic product.

Closed

20-03136

Plastics and Polymers

CANADA LABORATORY Canadian based laboratory needed for for testing plastics biodegradability

Closed

20-03124

Plastics and Polymers

USA Materials Laboratory needed for silicon carbide porosity and density testing. Mercury infiltration method is preferred. Material tested: Silicon Carbide infiltrated with Silicon.

Closed

20-03120

Plastics and Polymers

Polymer Laboratory needed for PET material composite testing o to determine the percentages of the ingredients of PET. Your fast response will be highly appreciated.

Submit Response

20-03117

Plastics and Polymers

Automotive Laboratory needed for testing plastic parts of vehicle to the following General Motors Test Standards: GMW14298, FMVSS108, GMW15424, GMW14797, CG1663

Closed

20-03111

Plastics and Polymers

INDIA LABORATORY (Mumbai Preferred) MULTIPLE TESTS India Polymer Materials Laboratory DMA (dynamic Mechnaical analyzer ) test for polymer, and UTM (Universal Testing machine) on industrial polymer. Thank You

Closed

20-03107

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS Automotive Laboratory needed for testing validation of various OEM plastic parts such as (OSDH, Bumper, Fascia, Grill, OSRVM, Wheel cover, Wheel house liner and others) of automobile. Therefore, we need to test them in different validations .

Closed

20-03099

Plastics and Polymers

Contract Laboratory needed for ISO window films testing (thin plastic films) under ISO 21702:2019 standard for SARS-CoV-2 for antimicrobial capabilities. ISO 21702:2019 refers to testing of measurement Of Antiviral Activity On Plastics And Other Non-Porous Surfaces. Thank you and please revert my inquiry to the appropriate staff to quote us.

Closed

20-03094

Plastics and Polymers

Contract Laboratory needed for the following LDPE plastic bags testing:  Tensile strength, length N  Tensile strength, width N  Tear resistance length N/mm²  Tear resistance width N/mm²  Bottom seam in N  Dart drop in g

Closed

20-03065

Plastics and Polymers

Polymer Laboratory needed for the following Polypropylene polymer tests (TDS): 1. Melt Flow Index 2. Density 3. Tensile Strength & Elongation 4. Flexural Modulus 5. Notch Izod Impact Strength 6. Hardness (Rockwell) 7. Vicat Softening Point

Closed

20-03041

Plastics and Polymers

MULTIPLE TESTS Polymer Laboratory needed for the following PVC flexible gasket tests:

*Coefficient of Friction Testing of each one, *amount CaCo contain in each one *Ash contain

Closed

20-03025

Plastics and Polymers

USA LABORATORY USA Materials Laboratory needed for analysis of two samples of PET monofilament racquet string analyzed via NMR to see differences and to reverse engineer one sample.

Closed

20-02994

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS MULTIPLE PRODUCTS LONG-TERM CONTRACT Healthcare Manufacturer needs USA Microbiology Laboratories to quote at 1 lot volume on the following tests below.

Please quote at 1 lot volume for each test. LAL Kinetic Chromogenic Inhibition/Enhancement ValidationLAL Kinetic Chromogenic TestInhibition/Enhancement LAL Gel Clot TestLAL Limit ScreenANSI/AAMI/ISO 11737-1: BioburdenValidation of BioburdenANSI/AAMI/ISO 11737-2: SterilityBacteriostasis and Fungastasis Validation Test

Closed

20-02985

Plastics and Polymers

EUROPE LABORATORY Europe Contract Laboratory needed for EN testing of neoprene sheets 20 mm x 300mm x 2000 mm to en 1337-3-2005 Structural bearings. Elastomeric bearings

Closed

20-02979

Plastics and Polymers

Medical Research Laboratory needed for developing a study for the health influence on swallowing's a plastic toy made of TPR

Closed

20-02968

Plastics and Polymers

Contract Laboratory needed for ISO antiviral activity to ISO21702:2019 Measurement of antiviral activity on plastics and other non-porous surfaces testing for our sample

Closed

20-02967

Plastics and Polymers

Electrical Laboratory needed for voltage apply is 1V to JIS K 6271 Rubber, Vulcanized Or Thermoplastic - Determination Of Volume And Surface Resistivity

Closed

20-02957

Plastics and Polymers

USA Based Contract Laboratory needed for PAH Analysis (non-alkylated) for maleic-itaconic copolymer, partial calcium salt - 40% in aqueous solution per SW 846 to meet Maryland Department of Agriculture requirements for soil amendment products.

Closed

20-02909

Plastics and Polymers

Contract Laboratory needed for ISO Soil biodegradability testing to ISO17556 Plastics ? Determination of the ultimate aerobic biodegradability of plastic materials in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved

Closed

20-02892

Plastics and Polymers

USA LABORATORY MULTIPLE TESTS LEGAL NGO involved in Prop 65 litigation needs USA Contract Laboratory for the following two tests:

1. phthalate (DEPH) test on a plastic product, and also a quote for orders of 5-10 tests at a time. 2. acrylamide in food? If so, can you please give me a similar price quote? Thank you.

Closed

20-02889

Plastics and Polymers

MULTIPLE TESTS MULTIPLE PRODUCTS Medical Device Laboratory needed for AAMI testing on various medical plastic disposables and to generate test reports for te following AAMI Test Standards :AAMI 2AAMI 3AAMI 4ASTM F1670-2003ASTM F1671-2003 Waiting for your reply

Closed

20-02886

Plastics and Polymers

MULTIPLE TESTS Pharmaceutical packaging company needs Packaging Laboratory for the following ASTM testing on blister laminates (PVC/PVDC). The tests to be performed are given below. Tensile strength, elongation at break, vicat softening point, Sealing (peeling test), water vapour transmission rate.

Closed

20-02823

Plastics and Polymers

MULTIPLE PRODUCTS India Company needs Polymer Laboratory for testing three PVDF polymer grades tested according to 3-A Sanitary Standard for Multiple-­-Use Plastic materials.Please provide quotation for the same so we can proceed further.

Closed

20-02773

Plastics and Polymers

MIDDLE EAST LABORATORY Middle East Laboratory needed to measure the viscosity of Polyether Polyol using method ISO3219 Plastics ? Polymers/resins in the liquid state or as emulsions or dispersions ? Determination of viscosity using a rotational viscometer with defined shear rate

Closed

20-02734

Plastics and Polymers

Polymer Laboratory needed for Transmittance and reflectance of polymer film with thickness ranging from 1/31 to 1/4

Closed

20-02733

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for PS. 50014 resin approval test of FCA with Plating molding. Test items are Appearance, adhesion (Saw Grind Test, Thermal Cycle test), and Adhesion/Corrosion Thermal Cycle Test Concurrent with CASS test.

Submit Response

20-02715

Plastics and Polymers

Materials Laboratory needed for UV aging testing on a plastic component

Closed

20-02706

Plastics and Polymers

Polymer Laboratory needed for Intrinsic Viscosity testing of PET under standard test conditions.

Closed

20-02693

Plastics and Polymers

MULTIPLE PRODUCTS Manufacturer needs Materials Laboratory for ASTM OTR testing for nylon film for vacuum bags on different films to ASTM D3985 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor

Closed

20-02689

Plastics and Polymers

MULTIPLE TESTS Contract Laboratory needed with a VOC chamber simulate sunlight lighting conditions for testing of VOC gas on painted versus bare plastic sheet.

Need pricing on the following: How much is the chamber test+UV for 1 type of VOC gas?

can I get a quotation for 2 VOC removal testing (paint coated vs no-paint uncoated 30x30cm plastic sheet)

Closed

20-02670

Plastics and Polymers

LEGAL Law firm needs Materials Laboratory for testing done on plastic materials emanating from a factory that produced food. We could also potentially need the tester to provide testimony at trial.

Closed

20-02625

Plastics and Polymers

Medical Device Company needs Materials Laboratory needed for recertifying expired PEG 600 and PEG 1450.for continued use. Expired 2019 in production facility for catheter and biologics medical device and implants

Closed

20-02621

Plastics and Polymers

Food Laboratory needed for leakage tests for biodegradable food containers made from bamboo pulp with EVOH lamination film? There is a leakage test in Europe using 97% nitrogen + 3% hydrogen as a detection gas to check for pores or leakage.

Closed

20-02593

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS USA Materials Laboratory needed for the following fabric reinforcement testing of resin laminates

1. Resin Solids 2. Volatiles 3. Flow 4. Gel Time

Types are based upon fabric reinforcement used and are defined per AMS-C-9084: MILITARY SPECIFICATION: CLOTH, GLASS, FINISHED, FOR RESIN LAMINATES Type 120 Type 1581 Type 7781 Type 1584

Closed

20-02591

Plastics and Polymers

MATERIALS LABORATORY NEEDED FOR MIGRATION TESTING FOR POLYPROPYLENE WOVEN FABRIC. PLEASE RESPOND WITH A QUOTE AND SAMPLE DETAILS TO PROCEED FURTHER

Closed

20-02579

Plastics and Polymers

Manufacturing company needs Materials Laboratory for the following UV transmittance testing on plastic specimens.

Acrylic specimen for the UV transmittance. (to measure the spectral transmittance of the specimen in the range of 290 nm to 330 nm wavelength band and to find the maximum percentage of transmission of UV light through the specimen). Report the value of one specimen of 1/2 in. ± 0.01 in. (12.7 mm ± 0.25 mm) thickness with light passing through polished faces. Report the maximum per cent transmission detected between 290 nm and 330 nm and the peak location where the maximum per cent transmission was located.

Closed

20-02565

Plastics and Polymers

MULTIPLE PRODUCTS Medical Device Company needs Materials Laboratory for ASTM Anaerobic Biodegradation Studies to ASTM-D5511 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions for 180 days max.

Closed

20-02524

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for the following test on plastics packaging trays:

FT-IR Analysis (TO identify the presence of Silicon Oil and Amide) GC/MS Analysis Hydrocarbon Residue (WD Doc. No. 2092-771690 AE)

Closed

20-02508

Plastics and Polymers

Contract Laboratory needed for OECD435 testing of strontium to determine if it is a skin corrosive 1A under CLP (H314: Causes severe skin burns and eye damage) without testing, but based on pH>11.5. For transport, pH is not considered, so we would like to test to define if we need to classify or not. In Europe we are already classifying it as corrosive for transport (UN3131); in Asia they don't (UN 3208 - by lack of corrosivity study results) and that causes marketing disadvantages in Europe.

So therefore our request for a study to define the corrosivity for once and for all. Only for transport - as the CLP rules continue to apply.

Sr reacts with water. The reaction is exothermic but not violently. So there is no problem accumulating explosive concentrations of H2 gas when working under the hood.

Closed

20-02504

Plastics and Polymers

FDA Contract Testing Facility needed for BFE and PFE, fiber diameter size and air permeability testing of PP Melt-blown filter. Can you give us a quote for BFE and PFE testing at your institute and also, the test to check fiber diameter size and air permeability. Please let me know if you have any questions.

Closed

20-02494

Plastics and Polymers

Materials Laboratory needed for Capillary Rheology of PVC: 1) Viscosity flow curve ( 10^3 to 10^5) 2) Die swell measurement 2) Haul off test Please provide the lead time for the test and estimate the price of the test

Closed

20-02475

Plastics and Polymers

Materials Laboratory needed to develop EN rubber profile for HL1/HL2 or HL3 as per EN455545-2-R7for railway door rubber & to be used for Railway application, Its base polymer EPDM. Please provide quote

Closed

20-02470

Plastics and Polymers

USA Pharmaceutical Laboratory needed for USP Testing of PET bottles to USP <661.1> absorbance, acidity or alkalinity, total organic carbon (TOC), and extractable metals. Wonder how long this would take to complete and what is all necessary to send out.

Closed

20-02468

Plastics and Polymers

MULTIPLE TESTS Automotive company needs Materials Laboratory needed for photo evidence and materials analysis including elasticity testing to identify the difference between 19 known used sample rubber gasket and suspected gasket that was never replaced, but claimed to be used.

Closed

20-02466

Plastics and Polymers

EUROPE PREFERRED BUDGET APPROVED ($4,000 EUROS) MULTIPLE TESTS MULTIPLE PRODUCTS Contract Laboratory needed for ISO antiviral testing of coated plastic foils according to ISO 21702 Measurement of antiviral activity on plastics and other non-porous surfaces.

At the moment we do not know the final application of our coated PET film. Therefore we like to do the tests in a general way, mostly according to the norm. We think that the following test conditions are optimal. However, since we have limited knowledge of the test, we are open to alternative suggestions from you: - The SARS-CoV19 or a surrogate such as HCoV-229E should be used. - The test substrate is a coated PET film with an active substance in the lacquer. - As reference substrate we propose a PET film according to table B.2 of ISO 21702. - Two different incubation

Closed

20-02453

Plastics and Polymers

Large Manufacturer needs Contract Laboratory for Anti-Virus Testing of High Pressure Laminates. We would like to test the below virus:SARS-COV-2H1N1 (Influenza Type A)ROTAVIRUSRSV Is it possible to get the above testings done? If yes please send us the quotation as well as timeline.

Closed

20-02446

Plastics and Polymers

Packaging Laboratory needed for OTR testing for packing industry. Film thickness is 2.0 - 4.0 Mila

Closed

20-02432

Plastics and Polymers

Medical Device Laboratory needed for quality control testing for polypropylene plastic used for medical gowns. See list of test requirements below. This will be for gowns from 2 different vendors: - flammability at front of gown - tensile, grab, dry at front of gown - tensile, trapezoidal tear, dry at front of gown - spray impact, water resistance, impact penetration at front of gown and sleeve seam. - water resistance, hydrohead at front of gown and sleeve seam - water vapor transmission rate at front of gown - seam strength at sleeve seam - lint at front of gown

Closed

20-02424

Plastics and Polymers

BUDGET APPROVED ($8000) Contract Laboratory needed for ISO 21702 Measurement of antiviral activity on plastics and other non-porous surfaces against Feline coronavirus and Human coronavirus 229E

Closed

20-02412

Plastics and Polymers

Contract Laboratory needed for chemical compatibility study of disinfectant cleaning process with Rubber and Plastic. for usage of product on escalator rails. NDA is required which we are sure this is your standard mode of operation as well.

Closed

20-02409

Plastics and Polymers

Contract Laboratory needed for ISO testing of plastics against coronavirus to ISO Test Standards: ISO 22196 and ISO 21702

Closed

20-02397

Plastics and Polymers

USA LABORATORY (California Preferred) USA Materials Laboratory needed for the following testing on Polypropylene Regrinds Item Condition Value Melt Flow 230C/2.16kgs g/10 min Notched Izod Impact 73F (=23C) ft.lb/in Flex Modulus 1% Secant PSI Tensile Strength Yield PSI Tensile Strength Break PSI

Closed

20-02381

Plastics and Polymers

USA LABORATORY BUDGET APPROVED ($5.000) USA Materials Laboratory needed for Deformulation/Reverse Engineering of a fishing pole polymer part along with it's MSDS. The products is made from a Polymer with Nylon and Graphite.Assistance with patent protection may also be needed.

Closed

20-02361

Plastics and Polymers

Materials Laboratory needed for ISO 21702 test at 30 min and 1 hour of our polymer film

Closed

20-02349

Plastics and Polymers

Contract Laboratory needed for plastic biodegradability test as per ASTM D 6954 Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation

Closed

20-02327

Plastics and Polymers

Food company needs Laboratory to perform ASTM puncture resistance testing to (ASTM F1306) on a laminated film structure.

Closed

20-02284

Plastics and Polymers

LONG-TERM TESTING USA Medical Device Laboratory needed for per lot Certificate of Analysis COA testing/certification that finished injection molded plastic medical device components are DNA/RNA free

Closed

20-02231

Plastics and Polymers

Contract Laboratory needed for ISO Plastics Antiviral Testing to ISO 21702 Measurement Of Antiviral Activity On Plastics And Other Non-Porous Surfaces

Closed

20-02225

Plastics and Polymers

MULTIPLE PRODUCTS Large Automotive COmpany needs Laboratory for survivability testing of SARS-Cov-2 (or substitute such as HCoV-229E) and flu viruses on multiple automotive interior surface materials (textile, artificial leather, coated plastics, etc) at various temperatures (40-60°C), humidity (20-80%), and dwell times (10-30min). Please call me to discuss a project quote and schedule?

Closed

20-02222

Plastics and Polymers

Contract Laboratory needed for fuel engine compatibility testing of fuel that been made by plastic by a pyrolysis method to determine if engine safety.

Closed

20-02220

Plastics and Polymers

FDA GMP Packaging Laboratory needed for USP Testing of HDPE Bottles to USP <661> and USP <671> .

Closed

20-02160

Plastics and Polymers

Analytical Test Laboratory with Quick Turn-Around TIme (TAT) needed for pesticide or insecticide residue testing on plastic resin (pellets and or plastic film

Closed

20-02158

Plastics and Polymers

Construction Materials Laboratory needed for ASTM F970 testing on Solid Vinyl Tile. Could someone contact me in regard to price. Thanks

Closed

20-02157

Plastics and Polymers

MULTIPLE TESTS Contract Laboratory needed for the following Polyurethane Foam Seat Cover testing:

flammability test FAR Part 25 §25.853 (a) and Appendix F Part I , for toxicity ( as per BSS 7239) and heat release test also.Can you please confirm whether we have facility to this test in your lab and if yes please share the quotes for complete testing , sample sizes required and tentative time.

Closed

20-02151

Plastics and Polymers

Materials Laboratory needed for basic testing of acrylic polymers r adhesive applications to include in our Technical Data Sheets.

Closed

20-02133

Plastics and Polymers

BSL-3 Certified Laboratory needed for ISO and AATCC antiviral testing for SARS-CoV-2 for the ISO 18184 test method for flexible polyurethane material.

Closed

20-02127

Plastics and Polymers

Contract Automotive Laboratory needed for tire crumb testing.

Closed

20-02116

Plastics and Polymers

Large Corporation needs Materials Laboratory for ASTM Stress crack testing on a HDPE plastic material per ASTM D1693. Part name is Nozzle plate for Pure Flow 1000 Eye wash station.

Need a quote for the test.

Closed

20-02102

Plastics and Polymers

URGENT MULTIPLE TESTS

Contract Laboratory needed for Films testing for antimicrobial behavior including the following analyses: oxidation (OIT) analysis, - FTIR - Co2 evolution- CO2 evolution in accordance with ASTM6954- test on plastic or rubber surfaces to ISO 22196 and ISO 21702:2019I would like to know how much is the cost for each services, it would be great if we can have a quotation as soon as possible.

Closed

20-02079

Plastics and Polymers

SOUTH AMERICA LABORATORY South America Laboratory needed for ISO 21702 measurement of antiviral activity on plastic, test the ability of plastics to kill viruses that have come into contact with the surface of the treated material. Conducted over a 24 hour period of contact with the virus ( Influenza A virus, Feline calicivirus or similar)

Closed

20-02077

Plastics and Polymers

MULTIPLE TESTS Polymer Laboratory needed for HDPE testing for the following

1. Specific Weight.

2. Molecular weight.

3. Composition of the sample (100% HDPE?).

4. Material composition: 4.1. If it is virgin HDPE. 4.2. If it is recycled HDPE. 4.3. If it is a mixture of virgin and recycled HDPE, and in percentages.

Closed

20-02064

Plastics and Polymers

MULTIPLE TESTS Materials Laboratory needed for PVC sheets testing for the following parameters; Physical Properties, Mechanical Properties, Thermal Properties, Electricity Properties

Looking forward to a comprehensive response and quote.

Closed

20-02056

Plastics and Polymers

Contract Laboratory needed for ISO Antiviral Activity testing to iso 21702 Measurement of antiviral activity on plastics and other non-porous surfaces

Closed

20-02012

Plastics and Polymers

MULTIPLE TESTS Medical Device Contract Research Organization needed for medical resin testing for the following standards: ISO 4049 Polymer-based restorative materials ISO 10477 Polymer-based crown and veneering materials ISO 10993-1, Biological evaluation of medical devices - Part 1: Evaluation and testing within a risk management process ISO 10993-5 Biological evaluation of medical devices - Part 5: Tests for in vitro cytotoxicity ISO 10993-10 Biological evaluation of medical devices - Part 10: Tests for irritation and skin sensitization

Closed

20-02006

Plastics and Polymers

Contract Laboratory needed for antiviral testing for SARS-CoV-2, or human/other similar coronaviruses (e.g. human coronavirus 229E). We would like to test a solid plastic/rubber surface loaded with antimicrobial for antiviral activity

Closed

20-01994

Plastics and Polymers

EUROPE LABORATORY Europe Contract Laboratory needed for ASTM biodegradation testing of packaging plastic under anaerobic condition to ASTM D5511

Closed

20-01969

Plastics and Polymers

MULTIPLE TESTINGS Pharmaceutical Laboratory needed for multiple quality tests of containers, closures and connectors for sterile catheters as per the following regulations:3.2.2. Plastic containers and closures for pharmaceutical use (EUROPEAN PHARMACOPOEIA)3.2.9. Rubber closure for containers (EUROPEAN PHARMACOPOEIA)Intravascular catheters - Sterile and singleuse catheters - Part 1: General requirements (ISO 10555-1)Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications Waiting for your kind feedback on availability of tests and quotes.

Closed

20-01957

Plastics and Polymers

Contract Laboratory needed for PVC cement pressure tested to BS EN 14814:2016 and Catonic bitumen emulsion tested to EN13808

Closed

20-01933

Plastics and Polymers

MULTIPLE PRODUCTS

Large corporation needed for MALDI TOF on polyurethanes samples mass around 100 to 800kDa.

Closed

20-01911

Plastics and Polymers

Materials Laboratory for film testing for Outer Wrap Shrink film. Please send us the Quotation of following testing. 1. HAZE 2. Gloss 3. Secant Modulous 1% - MD & CD 4. Tear Resistance- Elmendorf MD, g/sheet Material Description - 65 mic Clear LDPE Film Application - Outer Shrink Wrap

Closed

20-01907

Plastics and Polymers

Materials Laboratory needed for laminate structure testing to for identify each polymer substrate and the individual layer thickness.

Closed

20-01903

Plastics and Polymers

Contract Laboratory needed for Antiviral testing required for SARS COVID -19 virus on a polymer sheet from a verified laboratory.

Closed

20-01862

Plastics and Polymers

LONG-TERM PROJECT (Multiple Products) USA LABORATORY Large Company has project that is focused on characterizing our raw materials for both physical and chemical characteristics in an attempt to improve front end quality. Raw materials consist of polymers, organic and inorganic chemicals. In short, the target of the project is to characterize up to 6 lots of each raw material. We are looking for similarities or differences in purity and quality. Each chemical has been reviewed and a specific set of analysis assigned to determine contaminants or by-products that may affect final product quality. Over the last few years we have been doing the analysis in-house however recent reductions in timelines have challenged our resources so its been decided to explore outsourcing. The techniques we need support with are NMR, ICP, LC-MS, GC-MS

Closed

20-01854

Plastics and Polymers

India NABL Laboratory needed for Testing of 5 HDPE material of cable for brittlement and absorptions of coefficient.

Closed

20-01847

Plastics and Polymers

Maritime Laboratory needed for certification testing Rigid Polyurethane Foam for Coast Guard floatation specifications for boats and barges

Submit Response

20-01841

Plastics and Polymers

USA. Laboratory needed for film antiviral surface protection to USA standards. The most interest for the moment, is to test our product against virus proliferation.

Closed

20-01824

Plastics and Polymers

Contract Laboratory needed for antiviral protection testing of plastic injection molded toys .

Closed

20-01806

Plastics and Polymers

URGENT

Large corporation needs Oil Laboratory for ASTM rubber process oil kinetic viscosity testing @ 40 Celsius according to ASTM D 445. 2 Samples. Please share the quotation if you can perform this testing ASAP.

Closed

20-01791

Plastics and Polymers

Physical Laboratory needed for bank card testing for Durability - Temperature and Humidity Exposure, it is stated that if the product is guaranteed to be stored at a certain temperature and controlled humidity, its intended use may be 3 years

Closed

20-01752

Plastics and Polymers

Large Medical Device Company needs Materials Laboratory for Index of refraction per ISO 489 and/or ASTM D542 for a PVC in a film

Closed

20-01746

Plastics and Polymers

GLP Laboratory needed for ISO 21702 Measurement of antiviral activity on plastics and other non-porous surfaces, 3 replicas, GLP - testing with Norovirus and Mycobacterium tuberculosis please call me to discuss.

Closed

20-01743

Plastics and Polymers

Materials Laboratory needed for PVC material testing for compliance with all California standards for biodegradation and composting. Please feel free to reach out to me via email/phone if more information is needed.

Closed

20-01724

Plastics and Polymers

Contract Laboratory needed for ISO antiviral properties testing on the plastic films. preferably anything similar to ISO ISO21702 film testing ISO18184 fabric testing

Closed

20-01719

Plastics and Polymers

MULTIPLE PRODUCTS MULTIPLE TESTS

Polymer Materials Laboratory needed for the following multiple tests on the HDPE of used in some of our products: 1. Specific Weight. 2. Molecular weight. 3. Composition of the sample (100% HDPE?). 4. Material composition: 4.1. If it is virgin HDPE. 4.2. If it is recycled HDPE. 4.3. If it is a mixture of virgin and recycled HDPE, and in percentages. Can you do that or recommend us somebody ? Thanks in advance for your kind cooperation.

Closed

20-01705

Plastics and Polymers

Automotive Laboratory needed for ANSI Testing to ANSI Z26.1,Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways - Safety Standard conducted on some flat polycarbonate sheet. If so, can you provide me a formal price quotation to perform 2 tests?Thanks!

Closed

20-01699

Plastics and Polymers

MULTIPLE TESTS

Contract Laboratory needed for Biodegradability of plastic materials in a marine environment according to the following ASTM and ISO Test Methods:

ASTM D 6692-2001 Standard Test Method for Determining the Biodegradability of Radiolabeled Polymeric Plastic Materials in Seawater

ASTM D 6691-2009 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum

ISO 19679-2016 Plastics ? Determination of aerobic biodegradation of non-floating plastic materials in a seawater/sediment interface ? Method by analysis of evolved carbon dioxide

ISO 18830-2016 Plastics - Determination Of Aerobic Biodegradation Of Non-Floating Plastic Materials In A Seawater/Sandy Sediment Interface - Method By Measuring The Oxyg

Closed

20-01677

Plastics and Polymers

URGENT

Contract Laboratory needed for the following comparison study of the anti-virus properties of coated materials against COVID-19. We coated the water based paint on 5*5 cm acrylic sheet and compare coated and non-coat in term of the log of virus. after contact time 24 hours. We have already test Human corona virus 229E, NL63 and H1N1 we can share the report if you need.

Closed

20-01622

Plastics and Polymers

Manufacturer needs Contract Laboratory for biodegradability testing of adhesives tapes along with cellophane as film and rubber and resins based adhesive. Please email us for more informtion and to provide us with a quotation.

Closed

20-01621

Plastics and Polymers

Materials Laboratory needed for ASTM testing of plastic packaging as per the following 3 ASTM Test Standards:

COF- coefficient of Friction as per ASTM D1894 MVTR - Moisture vapor Transmission Rate testing as per ASTM F1249 OTR - Oxygen Transmission Rate Testing as per ASTM D3985

Closed

20-01600

Plastics and Polymers

Contract Materials Laboratory needed for AASHTO Standard Specification Testing for Epoxy Resin Adhesives for Bonding Traffic Markers to Hardened Portland Cement and Asphalt Concrete

Closed

20-01576

Plastics and Polymers

NEW PRODUCT DEVELOPMENT Plastics Company formulating new product with virucidal effects against COVID 19 needs R&D Laboratory for antiviral activity testing on plastics. Please provide quote.

Closed

20-01569

Plastics and Polymers

USA LABORATORY (Northeast Preferred) Contract Analytical Test Laboratory needed for Certificate of Analysis testing on a powder Calcium Hydroxide and Polytetrafluoroethylene (PFTE).mixture

Closed

20-01540

Plastics and Polymers

Toy Laboratory needed for CPSIA and ASTM F963 plastic toy testing to ensure they are non toxic, bpa free, phthalate free and lead free. Would you mind giving us a quote for that specific test?

1 - CPSIA (15 USC 1278a) - Lead in accessible substrate materials 2 - CPSIA (16 CFR 1307) - Phthalates 3 - 4.3.5.2 (ASTM F963-17), Toy Substrate Materials - Total Lead & Soluble Test for Metals 4 - 4.2 (ASTM F963-17), Flammability 5 - ASTM F963-17, Mechanical and physical properties  

Closed

20-01517

Plastics and Polymers

Contract Laboratory needed for ISO Antiviral testing on non porous surfaces according to ISO 21702 Measurement of antiviral activity on plastics and other non-porous surfaces

please describe test method, testing sample requirements, lead time for testing, laboratory availability and price quote.

Closed

20-01498

Plastics and Polymers

MULTIPLE TESTS PROJECT Materials Laboratory needed for the following tests of Polyvinyl Chloride PVC Electrical tape: Indian Standard against testing need to be done :- IS 7809 / IEC 60454 following tests need to be done :- 1) Resistance to flame propagation (IS 7809 part2:1977 / IEC 60454-2. 2) tensile strength - IS 7809 part2 : 1977 3) adhesion to steel - IS 7809 part2 : 1977 4) adhesion to backing - IS 7809 part2 : 1977 5) dielectric strength at room temperature - IS 7809 part2 : 1977 6) dielectric strength after humid condition - IS 7809 part2 : 1977 7) electrolytic corrosion - IS 7809 part2 : 1977 and IS 8516 8) stability to accelerate ageing - IS 7809 (part3 / sec 1) : 1986

Closed

20-01471

Plastics and Polymers

EAST COAST USA LABORATORY USAPackaging Laboratory needed for compatibility study analysis a High Density Polyethylene HDPE container. Additionally looking for a lab that can perform a compatibility study of the same container with product in it.

Closed

20-01468

Plastics and Polymers

Materials Laboratory needed for ISO Testing of plastic films ISO 21702 Measurement Of Antiviral Activity On Plastics And Other Non-Porous Surfaces

If so what is the cost for doing such test for checking anti viral capability of plastic films tested after 15 minutes , 1 hr , 24 hours

Closed

20-01455

Plastics and Polymers

USA LABORATORY (Northeast USA Preferred) Pharmaceutical Packaging Laboratory needed for child proof certification for single use, non-torque (pop top) container. The container needs to be certified compliant for drugs/medication (single use). Our containers need to be certified as child proof and I would think at a minimum would need to be FHSA and PPPA certified.

Closed

20-01450

Plastics and Polymers

Contract Laboratory needed for ISO antiviral activity testing of plastic polymer film to ISO 21702 Measurement of antiviral activity on plastics after 30 min, 1 hour, 24 hours.

Closed

20-01397

Plastics and Polymers

Polymer Laboratory needed for absorbency testing of polyurethane PU foam sample testing for the standard BS EN 13726 .

Closed

20-01376

Plastics and Polymers

Materials Laboratory needed for ASTM testing of silicone for its compliance to the requirements of ASTM C1184 Standard Specification for Structural Silicone Sealants for single Structural Glazing.

Closed

20-01375

Plastics and Polymers

Large Corporation needs Polymer Materials Laboratory for Index of refraction measurement of plastic film in 3um to 5um wavelength

Closed

20-01359

Plastics and Polymers

Polymer Laboratory needed for reverse engineering of PVC products that are not under any patent protection within the USA.

Closed

20-01352

Plastics and Polymers

Contract Laboratory needed for ISO testing of non-stick coatings of cookwares & other home appliances coatings (plastic and silicon coatings) to ISO 22196 Measurement Of Antibacterial Activity On Plastics And Other Non-Porous Surfaces

we want to test our products with ISO-22196 antimicrobial test.

Closed

20-01341

Plastics and Polymers

Microbiology Laboratory needed for ISO 21702 and ISO 18184 anti-virus activity and efficacy testing of anti-microbial copper film used on surface areas such as door knobs, elevator buttons, windows, etc .. test purpose: anti-virus activity and efficacy

Closed

20-01331

Plastics and Polymers

Consumer Products Laboratory needed for CPSIA Product Safety Testing of plastic toy to make sure they are non toxic, bpa free, phthalate free and lead free as per: 1 - CPSIA (15 USC 1278a) - Lead in accessible substrate materials2 - CPSIA (16 CFR 1307) - Phthalates3 - 4.3.5.2 (ASTM F963-17), Toy Substrate Materials - Total Lead

Closed

20-01324

Plastics and Polymers

Canada Laboratory needed for failure analysis of a the composition of a vinyl material applied to a sign face from varying periods, 2008 and 2014. The vinyl is applied to an acrylic substrate and utilized as a sign face. Material purchased and installed from the later period is showing evidence of deterioration (cracking and peeling) whereas vinyl from 2008 is remains intact.

Closed

20-01288

Plastics and Polymers

Polymer Materials Laboratory needed for HDPE lining materials pull force tensiometer tests on the HDPE material. The test samples needs to be tested to full destruction which will be approximately 700 neuton.Kindly advise if you will be able to conduct these tests for us and what will the cost per test be.Your soonest reply will be highly appreciated

Closed

20-01258

Plastics and Polymers

Contract Laboratory for ISO SARS-COV-2 Antivirus Efficiency Testing of textiles samples and plastic samples according iso18184 or iso 22196.

Closed

20-01257

Plastics and Polymers

USA Materials Laboratory needed for SATRA cold flex testing of polyurethane PU coated fabric as per Satra TM 55 method using Bally Flex machine at -10°C.

Closed

20-01245

Plastics and Polymers

Contract Test Laboratory needed for anti viral testing on plastic substrates as per ISO 21702 Measurement of antiviral activity on plastics and other non-porous surfaces

Closed

20-01237

Plastics and Polymers

Microbiology Laboratory needed for the determination of antiviral activity in plastic materials (ISO 18184:2014)

Closed

20-01211

Plastics and Polymers

Construction Materials Laboratory needed for hazardous chemicals testing in laminate flooring.

Closed

20-01193

Plastics and Polymers

Medical Device Company needs Polymer Laboratory for MW and Mw/Mn of PMMA Polymethyl Methacrylate

Closed

20-01100

Plastics and Polymers

Materials Laboratory needed for ASTM Testing of the oxygen transmission rates of different polyethylene films to ASTM Test Standard ASTM F1927. Our expected transmission rate can range from 0.05 cc mil / 100 sqin day - 100 cc mil / 100 sqin day. We'd like a quote for OTR testing per sample.

Closed

20-01087

Plastics and Polymers

Microbiology Laboratory needed for ISO anti-microbial and anti-viral testing of decorative laminates made of superimposed layers of paper impregnated with thermosetting resins used on furniture and interior surface solutions as per ( ISO 21702-2019 (Standard for plastics / ISO 18184 (Standard for textiles).

Closed

20-01085

Plastics and Polymers

Materials Laboratory needed for cool gel foam testing by which we can conduct a study differential temperature of cool gel foam in different environments.

Closed

20-01020

Plastics and Polymers

Life Sciences Company needs Bioanalytical Laboratory needed that can test and confirm presence of RNase and DNase enzymes in a sample laminate material (ie. plastic film)

Closed

20-00991

Plastics and Polymers

NEW TECHNOLOGY DEVELOPMENT Company needs Contract Polymer Laboratory to help with proof concept study for an new disinfectant technology which involves synthesize a new polymer group that cleaves to the current chain.

Closed

20-00982

Plastics and Polymers

URGENT Materials Laboratory needed to conduct comparison study of the OTR / WVTR of two different packaging system (Rigid vs Flexible). Film vs PET Bottle. Comparison will be conducted to the following ASTM standards: ASTM F1927 for Film and ASTM F1307 for the bottle

Closed

20-00980

Plastics and Polymers

Medical Device Company needs Contract Laboratory needed for antiviral testing with coronavirus for polymer surface testing against coronavirus to evaluate antiviral efficacy (or other standard viral species (enveloped, non enveloped)).

Closed

20-00977

Plastics and Polymers

Paper Company needs Independent Microbiology Laboratory for laminating film testing for antimicrobial efficacy against viruses and bacteria. I think it would be sufficient to test against the Human Coronavirus and the top 3 bacteria based on your recommendations. The broader the spectrum of efficacy that we are able to verify the better as long as it can be done affordably.

The antimicrobial technology incorporated into the topcoating of our polyester-based surface protection film contains silver ions in a zeolite carrier which purportedly inhibits the growth of microbes through disruption of cell metabolism and prevention of respiration. Our film is considered a treated article but has not been tested in its current configuration as a whole.

Please provide a quote and let us know how much material you would need in order to co

Closed

20-00967

Plastics and Polymers

Materials Laboratory needed for overall migration testing for plastic bags used to pack food products

Closed

20-00964

Plastics and Polymers

Medical Device Company needs Polymer Laboratory for polyurethane testing to specifications.

Closed

20-00960

Plastics and Polymers

Consumer Products Safety Laboratory needed for CPSC certificate testing for kids toys made of plastic and rubber in different colors.

Closed

20-00893

Plastics and Polymers

Materials Laboratory needed for ASTM testing of vacuum pack plastic material that will be used in custom vacuum pack bag manufacturing used to vacuum pack food. This material has to comply with measured oxygen transmission rate (OTR) greater than 10,000 cc (STP) (24 hours, m2, atm) according to guidelines listed in ASTM D3985. Attached is a letter describing this specification from another supplier of these bags. But we want to manufacture our own and submit them for certification. These bags will seal fresh fish fillets. What is the cost and turn around time? Final material will create vacuum bags that are 6x7 in.

Closed

20-00876

Plastics and Polymers

Europe :Laboratory needed for ISO anti-microbial testing of PVC adhesive films according to ISO 18184 or 21702. It is please possible to send us a price proposal for this test and an idea of a possible date for the results.

Closed

20-00857

Plastics and Polymers

Medical Device Laboratory needed for physical testing of injection molded medical device that incorporates a colorant in the resin. I need to have the physical properties tested of the blended material (resin+colorant). Density - ASTM D792, ISO1183 Melt Flow Rate (190C/2.16kg) - ASTM D1238, ISO 1133 Melting Point (DSC) - ASTM D3418, ISO 3146 Vicat Softening Point - ASTM D1525, ISO 306 Tensile Strength Shore A Hardness FDA 21 CFR 177.1350(a)(1) safe for food contact.

Closed

20-00831

Plastics and Polymers

Packaging Laboratory needed for Overall Migration and Specific Migration of plastic lids used in powdered milk packaging as per below Chinese standards: GB 4806-1-2016 GB 4806-6-2016 GB 4806-7-2016 GB 9685-2016 GB 31603-2015 GB 31604-2016

Closed

20-00786

Plastics and Polymers

Polymer Laboratory needed for recycled PET chips (polymer granules) testing for Acetaldehyde content and Limonene Content.

Closed

20-00780

Plastics and Polymers

Contract Laboratory needed for performing all FDA required testing for Polyester Isolation Gown level II testing

Closed

20-00778

Plastics and Polymers

FDA Medical Device Laboratory needed with experience with polymers for performing the following biodegradability, stability sterility studies andanalytical testing on a hydrogel - Molecular Weight and mole ratios Rheological Testing Viscosity Storage (G') and loss modulus (G'') vs temperature for 25 wt% polymer in saline - over a temperature range of 15 to 40 C Shear thinning during mechanical load of injection Sol to gel transition temp Sterility Shelf life Degradation products of gel over time, TBD Biocompatability What mass of material would be required? Costs for tests? Turn around time?

Closed

20-00775

Plastics and Polymers

Microbiology Laboratory needed for DIN microbial resistance testing of thermoset composite sheet, need testing for Resistance to Microbial Attack.

DIN 53739 or 53930/3

Closed

20-00735

Plastics and Polymers

Healthcare company needs Materials Laboratory d for confirmatory testing of Nitrile gloves to confirm that they are indeed nitrile, and not vinyl or latex.

Closed

20-00677

Plastics and Polymers

Microbiology Laboratory needed for conducting a product development study of a new plastic resin for the length of time an enveloped virus is viable on a it's polypropylene surface

Closed

20-00576

Plastics and Polymers

Construction Materials Laboratory needed for ASTM Skid Resistance Testing (Test Method D2047) part of the ASTM F3059 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding

Closed

20-00538

Plastics and Polymers

Microbiology Laboratory needed for toxicology studies of a spunbond PLA nonwoven to determine its' suitability for use in facemask applications including In Vitro Cytotoxicity - Agar diffusion test for cytotoxicity: ISO 10993-5 Skin Irritation:In Vitro EpiDerm Skin Irritation Test (EPI-200-SIT, OECD 439) Or Primary Dermal Irritation in Rabbits (ISO)

Closed

20-00494

Plastics and Polymers

Contract Laboratory needed for ASHRAE 199 testing for 100% polyester non-woven spunbond media

Closed

20-00492

Plastics and Polymers

Materials Laboratory needed for polyethylene PE Film sample as per ASTM D6954 Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation

Closed

20-00475

Plastics and Polymers

Polymer Laboratory needed for producing polymer films and then testing 3 samples of LDPE granules and need to measure density (ISO 1133) and tensile strength (MD/TD, ISO 527-3, 50 microns, BUR = 3:1) for this samples. We can provide only granules. Films need to be produced in your laboratory.

Closed

20-00471

Plastics and Polymers

Polymer Laboratory needed for Polymer Molecular Weight analysis testing

Closed

20-00455

Plastics and Polymers

Large Corporation needs construction materials laboratory for testing for Hardness and Fatigue test as per BPL002: Issue 3 BS EN ISO 3385 Flexible cellular polymeric materials ? Determination of fatigue by constant-load pounding

Closed

20-00451

Plastics and Polymers

POLYMER LABORATORY NEEDED FOR ASTM TESTING OF ACRYLIC/PVC PLASTIC SHEET TO THE FOLLOWING ASTM TEST STANDARDS:

ASTM D638 ASTM D790 , 256, 785, AND 648

Closed

20-00445

Plastics and Polymers

Analytical Chemistry Laboratory needed for testing plastisol formulations.

Closed

20-00443

Plastics and Polymers

Polymer Laboratory needed for identification of plastic used in some of the existing product Please provide me quote as well as typical lead time. Thank you

Closed

20-00419

Plastics and Polymers

Food Laboratory needed for 3 types of plastic cups with lid PP material testing including food contact and migration in compliance with UK and EU regulations for safety.

Closed

20-00414

Plastics and Polymers

Acoustics Laboratory needed for reverberation measurement on sound transmission through a 10mm rubber tube.

Closed

20-00372

Plastics and Polymers

Food Laboratory needed for EU compliance product testing of plastic cups for beverages and drinks as per EU safety regCompliance with EU food safety regulations in terms of migration. Overall Migration Specific migration Colours Certificationulations.

Closed

20-00364

Plastics and Polymers

DEA Packaging Laboratory needed for fold endurance testing of pharmaceutical film containing a schedule IV drug. Unpackaged film, packaged film, at two stability time points for two different formulations.

Closed

20-00356

Plastics and Polymers

North America Materials Laboratory needed for testing dental mouth guard device for identification of distinct chemical / plastic odour from the material.

Closed

20-00349

Plastics and Polymers

UK ISO 17025 Toxicology Laboratory needed for cytotoxicity testing on two types of foam.

Closed

20-00334

Plastics and Polymers

Materials Laboratory needed to test a polymer film sample on Atmospheric condition and detect the control release of additives through the film.

Closed

20-00295

Plastics and Polymers

Asia Materials Laboratory needed for EN 12667 thermal conductivity of thermal insulator using Polyurethane PUR foams

Closed

20-00257

Plastics and Polymers

Polymer Laboratory needed for PET Flakes testing. The tests we need are as follows: Presence of poly bromo diphenyl, poly chlorine diphenyl; Size of the flakes Impurities - metal, paper, wood, labels., etc; Moisture, Ph; Containing non-transparent plastic - OPAK; Presence of hazard chemicals; Mass density;  Melt temperature;Please let me know whether you can do the above test and what would be the price.

Submit Response

20-00246

Plastics and Polymers

Polymer Laboratory needed for ISO testing of polyurethane samples to the following laboratory test standards:

Analysis Method Unit Hardness ISO 868 Shore A Tensile strength EN 12803 MPa Elongation at break EN 12803 % Tear strength ISO 34-2 KN/m Abrasion resistance UNI EN 12770 mm3 Melt Flow Index MFI (5 kg, 205 °C) - g x10 min

Closed

20-00217

Plastics and Polymers

Consumer Products Laboratory (preferably Canada) needed for harmful chemicals testing in memory form and polyester used in pillows and mattresses like Methylene dianiline, Vinilideine chloride, Methyl benzene, Dimethylformamide fire resistance in mattresses companies might be using chemicals such as Polybrominated diphenyl ethers, boric acid, Chlorinated tris etc.

Please note this is for students science project.

Closed

20-00216

Plastics and Polymers

FDA GMP Packaging Laboratory needed for Pharmaceutical USP packaging testing , specifically a POLYETHYLENE TEREPHTHALATE bottle, for extractables and leachables to USP <661> or equivalent.

Can you please provide a quote. Thank you!

Closed

20-00204

Plastics and Polymers

Materials Laboratory needed for ASTM Testing of Rebar according to several ASTM Test Standards. The Rebar is made of Glass Fiber -Reinforced plastic(GFRP) of compositer material for 4 dimensions of 10,13,16 and 22mm

Testing per ASTM D7957 but require as follows

ASTM D7205/D792 Measurd cross-sectional Area-straight portion ASTM D7205 Tensile properties(strenght,modulus,strain)-straight portion ASTM D7617 Transverse shear strength-straight portion ASTM D7913 Bond strength to concrete ASTM D7205 Tensile strength post Alkaline Resistance exposure ASTM D7914 Strength of bent ASTM D7205 Tensile properties

??? 10mm,13mm,16mm,22mm

Closed

20-00154

Plastics and Polymers

Polymer Laboratory needed with the capability to determine vapor pressure as a function of temperature (-42 C to 71 C range) or even just vapor pressure at 71 C, for a series of fluids, including a silicone polymer, two fairly inert silanes, a low molecular weight fluorocarbon, and a heat transfer agent (blend of alkanes)? Please provide a price estimate.

Closed

20-00131

Plastics and Polymers

Materials Laboratory needed for Electrical insulation testing for switchboard sheets according to ASTM D 178 Standard Specification for Rubber Insulating Matting ( test fire, ozone, oil retardancy also ), if you can perform these tests, please send us the quotation for one piece.

Closed

20-00112

Plastics and Polymers

Packaging Laboratory needed to evaluate several anti static polypropylene valve bags. We have some suppliers who say they can make it, but I would need to set up a testing program to verify the resistance to static shock on the bags. I would like to get a contact to discuss testing cost and what would be needed to establish a base line for the product.

Closed

20-00089

Plastics and Polymers

ISO 17025 Accredited Automotive Laboratory needed for Ford Motor Company material specification for 2 vinyl materials to WSS-M8P3-F1/PERFORMANCE, FLEXIBLE POLYMERIC FILM, INTERIOR, SUPPORTED, DENIM DYE BARRIER TOP COAT ***TO BE USED WITH FORD

Closed

20-00081

Plastics and Polymers

Contract Test Laboratory needed for plastic testing for limonene levels

Closed

20-00051

Plastics and Polymers

Manufacturer needs Laboratory for testing domestic recycled high density polyethylene bottles for compliance with Japanesse chemical control law, philippine chemical control law, Korean chemical control law, China IECSC, IS9833:1981, U.S EPA TSCA Chemical inventory, Canadian CEPA DSL and NDSL and California Prop 65 list.

Closed

20-00047

Plastics and Polymers

PRODUCT DEVELOPMENT Research and Development Laboratory needed for reverse engineering and redevelopment of biodegradable bags that would be manufacturered in Canada.

Closed

20-00039

Plastics and Polymers

Clean-tech company needs North American Research Laboratory for R&D compostability testing of compostable of plastic alternative resin material.

Closed

19-01849

Plastics and Polymers

Film Maker needs Independent Laboratory for investigation and labeling claims testing of three plastics products for documentary.

1st company: They claim all their products are 100% organic, 100% non toxic, no petrochemicals, compostable, safe to be ingested by marine life, no GMO, the owner dissolve the cassava bag in hot water and drink it, the cassava starch bag can be burned and will not be carcinogen or release any dioxin.

I have already test for bio-content astm D6866, the results came with 49% fossil carbon. I need to know more about these 49%. I have also tested for PVOH, the lab that did the test wasn't really helpful « There is not significant PVOH and more test need to be done». My source who did test PVOH with another lab came with way more accurate results. But I need to do those test under my name.

I would need

Closed

19-01843

Plastics and Polymers

Tire Manufacturer needs Analytical Laboratory needed for XRD analysis. Please send quotation.

Closed

19-01834

Plastics and Polymers

Microbiology Laboratory needed for microbiological analysis in HDPE buckets, drums, cans and carafes?. I need mesophiles, coliforms, fungi and yeasts and if possible some pathogen such as Salmonella or E. coli; and also if you handle any chemical migration analysis, such as, heavy metal analysis

Closed

19-01829

Plastics and Polymers

India NABL Laboratory needed for certificate of analysis for polyurethane board

Closed

19-01828

Plastics and Polymers

Materials Laboratory needed for Melt Flow and Notched Izod testing of plastics that is located in the western part of the United States.

Closed

19-01816

Plastics and Polymers

Consumer Products Laboratory needed for boot testing for identification of materials (Leather and RUbber) used in the body of the boot and the sole. It should be used to determine if competitor product used full grain leather or a combination of leather and PU coating. also the sole of the boot was to be rubber and I am sure this is a injected PU sole.

Closed

19-01809

Plastics and Polymers

Contract Laboratory needed for a quote for USP <788> PM (particulate matter)analysis (light obscuration method) for medical devices. They're rubber stoppers, about an inch long, pooled in a group of 10. In total there would be 5 samples.

Closed

19-01801

Plastics and Polymers

Biotech Company needs Contract Sterilizer for Ethylene Oxide sterilization of plasticware. I have some initial testing I would need to perform, and then long term this supplier would be integrated with our manufacturing process.

Closed

19-01799

Plastics and Polymers

URGENT Materials Laboratory needed for USP penetrability testing of rubber stopper used in pharmaceuticals. Kindly send the quotation.

Closed

19-01788

Plastics and Polymers

Materials Laboratory needed for specific & over all migration testing of PET preforms to IS 9845.

Closed

19-01787

Plastics and Polymers

URGENT Plastics Products manufacturer needs Food Laboratory for migration testing of food contact surface product.

Closed

19-01775

Plastics and Polymers

Food Laboratory needed for third party migration testing certificate for plastics directly in contact with Food e.g. (Bakery Bags, Table Cover etc.)

Closed

19-01760

Plastics and Polymers

Electrical Laboratory needed for LT Panel (POLY CARBONATE) Testing For Temperature Rise As Per IEC:61439-1 with Aluminum Bus Bar of rating 600A.

Closed

19-01711

Plastics and Polymers

Medical Device Company needs Materials Laboratory for polymer characterization of nylon used in catheters.

Closed

19-01706

Plastics and Polymers

Hello,I am looking for qualified and certified laboratories in the US that are able to test under the norm ASTM D5338-15 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures . I appreciate your input on this.

Closed

19-01689

Plastics and Polymers

Polymer Laboratory needed for certification testing of clear PET flakes (recycled) to data sheet.

Closed

19-01656

Plastics and Polymers

Materials Laboratory needed for ISO biodegradability testing on PE tarpaulin according to ISO15985 Plastics ? Determination of the ultimate anaerobic biodegradation and disintegration under high-solids anaerobic-digestion conditions ? Method by analysis of released biogas

Closed

19-01643

Plastics and Polymers

Contract Laboratory needed to analyse emission generated after incineration of our polymer Emulsion sample.

Closed

19-01635

Plastics and Polymers

Polymer Laboratory needed for plastic identification evaluation as either Polycarbonate or PETG. Can you determine this with certainty? what methods will you use? and how much will it cost?

Closed

19-01634

Plastics and Polymers

Materials Laboratory needed for USP Method Differential Scanning Calorimetry DSC Analysis for 75 cc Round HDPE bottles

Closed

19-01626

Plastics and Polymers

Materials Laboratory needed for plastics ASTM flammability and materials testing to the folowing test methods: :WEIGHT ASTM D751 THICKNESS DIN EN ISO 2286-3 TENSILE STRENGHT ASTM D751 ELONGATION ASTM D751 TEAR RESISTANCE ASTM D5733 FLAMMABILITY FMVSS302 SHRINKAGE SAE J883 COLD RESISTANCE @ -30 °C SAE J323 Could you tell us if you can make it, time and cost?

Closed

19-01601

Plastics and Polymers

Accredited laboratory need to perform PVC fitting testing in compliance with requirements of ES BN 1329-1:2014 Plastics Piping Systems For Soil And Waste Discharge (Low And High Temperature) Within The Building Structure. Unplasticized Poly(Vinyl Chloride) (PVC-U). Specifications For Pipes, Fittings And The System (British Standard)

Closed

19-01591

Plastics and Polymers

Contract Laboratory needed for an evaluation of plastic cups and lids of Polypropylene. We are going to provide a new raw material that contains 30% filler-minerals. How can we identify that the raw material contains 30% minerals? Do you make this test in your lab? If yes, is necessary to send you pellet of raw material or the final product (cup or lid)?

Closed

19-01588

Plastics and Polymers

Pharmaceutical Laboratory needed for silicon rubber testing as per US FDA 21CFR

Closed

19-01585

Plastics and Polymers

URGENT ISO 17025 Third Party Laboratory needed for viscosity measurements (to any testing standard) of 10+ individual liquid polymer products

Closed

19-01570

Plastics and Polymers

Materials Laboratory needed for plastics thermal testing for  Thermal Shock (BI 107-05)  Size of each piece: 30.5 x 14 cm  Number of pieces for each test: 8 pieces for each test

2. Can you support us with the quote? 3 What is the delivery time of the tests? 4. Do we need to send specific information? (I am including in this mail, the standards required for each of the tests)

Closed

19-01568

Plastics and Polymers

Materials Laboratory needed for ASTM testing of PVC to ASTM-D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C With a Vitreous Silica Dilatometer

The Report should consist Unit of Measure; it should be in pursuance to Industry Standards valid in USA, UK and India.   Looking forward to hearing from you soon.

Closed

19-01566

Plastics and Polymers

Polymer Materials Laboratory needed for oxygen transmission testing on a profile extruded part to determine the OTR and WVTR, the profile needs to be properly sealed to pouch (epoxy) and then tested for OTR and WVTR.

Closed

19-01543

Plastics and Polymers

Packaging Laboratory needed for comparison study and leak resistance performance/properties study of PET/RPET clamshell food containers. Fill PET/RPET clamshell food containers with liquids (water, fruit juice, etc) and suspend them so the liquid is in contact with the lid and base of the container, and see how much/if any liquid escapes the container over x amount of time. I am not sure if there are any certifications/standards for this type of testing; if so, they are preferred.

Closed

19-01522

Plastics and Polymers

Coffeee Company needs Polymer Laboratory needed for non-destructive testing of cup thermoformed plastic us for Oxygen Transmission Rate (OTR) and Moisture vapor transmission rate MVTR. to ASTM D3985 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor or another suitable method.

Closed

19-01484

Plastics and Polymers

USA or Europe A2LA Polymer Laboratory needed for General Motors GMW Test Standards Testing to determine scratch resistance of polypropylene plaques using Taber Five Finger equipment and Erichsen Scratch test equipment as per GMW 14688 Scratch and Mar Resistance and GMW 14698.

Closed

19-01483

Plastics and Polymers

Materials Laboratory needed for aging studies on polyurethane insulation used on pipelines to the following ASTM Test Methods: 1) ASTM C335, 2) ASTM D2126

3) Assembly bond shear strength at 73°F ± 4 °F (23 °C ± 2°C) un-aged and thermally aged (pipe heated to 320F (160C) for 3600hrs or heated to 338F (170C) for 1450hrs)

4) Assembly bond shear strength at 284°F ± 4 °F (140 °C ± 2°C) un-aged and thermally aged (pipe heated to 320F (160C) for 3600hrs or heated to 338F (170C) for 1450hrs)

Please note that #3 and 4 involve heating a 10 foot long assembly and then cutting out three chunks for each test and utilize hot fluid pumped through the pipe with the jacket at room temperature. So that would be atmospheric pressure.

I will need an idea about turnaround time and cost.

Submit Response

19-01469

Plastics and Polymers

Materials Laboratory needed for Melt Flow Index Testing of plastic pellets to ASTM and ISO Test Methods: ASTM D1238, ISO1133

Closed

19-01464

Plastics and Polymers

Construction Laboratory needed for ASTM testing of silicone sealant used for construction and curtain wall to two ASTM Test Standards:

ASTM C 1184 for struction sealant ASTM C 920 for elastic sealant

Closed

19-01460

Plastics and Polymers

Contract Pharmaceutical Packaging Laboratory needed for USP Container Testing to USP661

Closed

19-01451

Plastics and Polymers

Large oil company needs Materials Laboratory for yellowness index testing for polyethylene PE pellets

Closed

19-01445

Plastics and Polymers

solid-state 13C NMR test is needed to analyze the structure of a new type covalent organic framework (organic polymer) which only contain C,H,O,N elements

Closed

19-01402

Plastics and Polymers

Microbiology Laboratory needed for ASTM Anti-microbiology testing on Canine parainfluenza virus (ATCC® VR-399T) to ASTM e 2180 Standard Test Method for Determining the Activity of Incorporated Antimicrobial Agent(s) In Polymeric or Hydrophobic Materials

Closed

19-01401

Plastics and Polymers

Materials Laboratory needed for ASTM biodegradation analysis of foams to ASTM D5511 or ASTM D5526 method specifically

Closed

19-01387

Plastics and Polymers

Materials Laboratory needed for ASTM biodegradability of floral foam made with phenolic resins to ASTM D5511 and ASTM D5526 I would like to have a quote . I pre-appreciate the answer to my request.

Closed

19-01382

Plastics and Polymers

Materials Laboratory needed for determining the optical characteristics (refractive index, scattering coefficient and absorption coefficient) for a sample of silicone rubber.

Closed

19-01363

Plastics and Polymers

Materials Laboratory needed ASTM biodegradability testing on plastics to (ASTM D-5511 and ASTM-5526)

Closed

19-01346

Plastics and Polymers

Materials laboratory needed for multiple tests (DIN and ISO) on Polyurethane as per below.

Mechanical loss factor DIN53513 Static shear modules DIN ISO 1827 Dynamic shear modulus DIN ISO 1827 Min. tensile stress at rupture DIN EN ISO 527-3/5/100 Min. tensile elongation at rupture DIN EN ISO 527-3/5/100 Abrasion test DIN EN ISO 4649 Residual compression set DIN ISO 1856 Static & Dynamic E-modulus test DIN 53513 Inflammability DIN 4102 EN ISO 11925-2

Please confirm the testing availability including the cost of each test and lead time to conduct the tests.

Your soonest reply on the above would be highly ap

Closed

19-01342

Plastics and Polymers

Third-Party Laboratory needed for wavefront distortion (400 - 700 nm) and optical birefringence tested. This is a customer request for testing by a third party laboratory.

I will need pricing, turnaround times, and sample requirements.

Closed

19-01325

Plastics and Polymers

Accredited laboratory needed to perform ASTM Biodegradation Testing of Plastic Films to ASTM D-5511 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions or D-5526 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions

Closed

19-01320

Plastics and Polymers

Large Oil Company needs Materials Laboratory for Vapor pressure osmometry for molecular weight measurement of polymers

Closed

19-01297

Plastics and Polymers

Polymer Laboratory needed for analysis of free monomer(Acrylic acid & Maleic Acid ) in Polyacrylic Acid based product . The specification limit is 1000 ppm .

Closed

19-01291

Plastics and Polymers

Materials Laboratory needed for ASTM Testing of packaging tapes to ASTM D5486 type 1 and type 2 testing for polyester packaging tapes.

Closed

19-01277

Plastics and Polymers

Laboratory needed for ASTM Biodegradable ( Aerobic and Anerobic) as per ASTM D6400/ASTM D6954.

Closed

19-01275

Plastics and Polymers

Northern Midwest USA testing facility needed for top load compression (plastic bottles), torque studies, leakage studies, vibration and simulated shipping, and product stability and weight loss over time. This is a partial list as we are still in development.

Closed

19-01197

Plastics and Polymers

Accredited laboratory needed for FDA and Proposition 65 testing of polypropylene for the following: 1. Determination of n-hexane and DBP content (According to Proposition 65) 2. Overall migration (According to EU10/2011): Polypropylene films 3. Heavy Metals (According to EU 10/2011) 4. Determination of extractables in Hexane / Soluble Xylene Fraction (According to FDA 177.1520) 5. Migration of certain elements (According to EN71-3: Safety of Toys)

The material we need to test is polypropylene.

If you can do these tests, please send us a quotation.

Thank you in advance.

Submit Response

19-01186

Plastics and Polymers

Contract Laboratory needed to characterize the refractive index of oil samples and rubber samples. I would like to do the measurement at elevated temperature (35C) for a few different wavelengths across the visible spectrum

Closed

19-01134

Plastics and Polymers

Microbiology Laboratory needed for JIS antimicrobial properties to Japanese Test Standard JIS Z 2801 Method Test for Antimicrobial Activity of Plastics

Closed

19-01133

Plastics and Polymers

NEW PRODUCT DEVELOPMENT Footwear Manufacturer developing new technology needs Product Test Laboratory for characterization of synthetic polyurethane materials used for the uppers in athletic footwear. . Laboratory testing of the following needed to industry standards. Laboratory will need to help identify the standards to test for the following

1. Abrasion Resistance - Taber and Martindale 2. Tear Strength 3. UV Resistance

Closed

19-01131

Plastics and Polymers

Physical Laboratory needed for compression deflection testing of several foam materials at various compression speeds to multiple compression percentages.

Speeds: 0.05, 0.10, 0.20, 0.20, and 0.30 m/s with readings for compression deflection at 10, 25, 40, 50, and 60%.

We have a Lloyd at are plant and typically can perform compression deflection testing however, the requested speeds are higher than our machine can test.

Closed

19-01087

Plastics and Polymers

ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics Composites

Closed

19-01080

Plastics and Polymers

Engineering Company needs Materials Laboratory for UL and IS Flammability Testing of PU FOAM as per UL94-1998,CLAUSE 12HF-1 Class & as per IS 15061 <38 MM. Please provide quote.

Closed

19-01048

Plastics and Polymers

USA Polymer Laboratory needed for maldi-tof or GPC w/light scattering and vapor pressure osmometry measurement for a polymer in organic solvent. Expected MW = 500-5000. Samples are combustible, low toxicity, low odor. Not air/moisture sensitive and do not require any special handling besides normal PPE. Would like to received a quote and estimated turnaround time for 10 samples. Separately, would like to know if you can do for the same 10 samples. If yes, would like a quote also.

Closed

19-01043

Plastics and Polymers

Certified Laboratory needed for ASTM flexible packaging film testing WVTR and OTR.For OTR, compliance with ASTM D-3985; and for WVTR with ASTM F-1249

Closed

19-01042

Plastics and Polymers

Contract Test Laboratory needed for (Polymer Film /Granules) of ASTM and ISO Biodegradability analysis(Aerobic & Anaerobic biodegradability testing to -ASTM- 6400/5338 and 6954 Standard), ISO 17088 testing

Closed

19-01029

Plastics and Polymers

Materials Laboratory needed for ASTM thermocycling testing for Polyethylene Aluminium Composite Pipe according to ASTM F1282-2010 standard's requirement. How much does it cost? Thank you.

Closed

19-01024

Plastics and Polymers

Asia Materials Laboratory needed for testing recycled plastic from Turkey for mfi;tensile stress at break;tensile stress at break

Closed

19-01001

Plastics and Polymers

Large Pharmaceutical Co needs Packaging Laboratory for the following analyses on PVC film 250 micron used for blister foil capsule product.

 MVTR or WVTR (moisture vapor transmission rate or water vapor transmission rate)  OTR (oxygen transmission rate)

Closed

19-00996

Plastics and Polymers

Materials Laboratory needed for VW Automotive Spec testing of polypropylene PP non woven material textile to spec VW 50180 Emission Testing on Automotive Interior Components

Closed

19-00994

Plastics and Polymers

ISO 17025 Contract Laboratory needed for biodegradability testing of bio-plastic composite products in accordance to ASTM D6954-04 or BS 8472

Closed

19-00992

Plastics and Polymers

Contract Analytical Test Laboratory needed for testing for chloroform soluble extractives on a sample of polyester in order to be in compliance with 21 CRF 177.1630 Polyethylene phthalate polymers

Closed

19-00983

Plastics and Polymers

Microbiology Laboratory needed for JIS anti-viral efficacy test on new paint coating on PE film according JIS-Z 2801 for inhibition to the growth of viruses such as Coxsackievirus A16 (CV-A16) that causes HFMD Or H1N1 virus that causes Influenza, that reduction over a 14 hours expose and compared the conventional paint

Closed

19-00982

Plastics and Polymers

Asia Polymer Laboratory needed for plastic testing for mfi;tensile stress at break;tensile stress at break

Closed

19-00976

Plastics and Polymers

Toxicology Laboratory needed for OECD Developmental Toxicity Study for polymer to OECD 414 Prenatal Development Toxicity Study

Closed

19-00974

Plastics and Polymers

USA Construction Materials Laboratory needed for ASTM testing on two types of Fiberglass Reinforced Plastic FRP grating ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials

Closed

19-00956

Plastics and Polymers

Materials Laboratory needed for research studies to help determine the current stress on molded sheets and in annealed sheet polymer plastic products. The various manufacturing methods we utilize for producing a stock plastic shape ( Sheets / Rods) causes stress in the sheet. This stress manifests itself as warpage when our customers machine the sheet product. We use a few annealing methods to remove the stress but we need research to help us determine the current stress within our as-molded sheet and in our annealed sheet products. We are looking for help in developing a standardized test to help us to measure residual stress in the compression molded sheets we produce. We want to use the testing to help us determine: 1. Is there residual stress in our as-molded sheet? 2. Which annealing process provides the best results for stress re

Closed

19-00937

Plastics and Polymers

Packaging Laboratory needed for air permeability testing per ISO 5636 using Gurley apparatus for sterile barrier packaging PE samples.

Could you please assist and let me know what other information will be needed to move forward with quote and evaluation?

Closed

19-00922

Plastics and Polymers

Northeast USA Materials Laboratory needed for friability (bead strength) of MP800 resin

Closed

19-00915

Plastics and Polymers

Analytical Chemistry Laboratory for reverse engineering and formulation of a tint to coat SPR rubber crumb that gets mixed with polyurethane and eventually made into rubber surfacing for playgrounds, driveways, pool decks etc.

Closed

19-00904

Plastics and Polymers

USA Materials Laboratory needed for AASTM D5511 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions

Closed

19-00902

Plastics and Polymers

Experienced Polymer Laboratory needed for ISO and ASTM oxygen index testing of polyurethane foam to ISO 4589 Plastics Determination of burning behaviour by oxygen index Part 2: Ambient-temperature test and ASTM D 2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

A brief description is below:

Definition Oxygen Index Test is widely used to measure burning performance of plastics, rubber, fiber, foam, softening sheet, film etc.,

Test Method A small test specimen is supported vertically in a mixture of oxygen and nitrogen flowing upwards through a transparent chimney. The upper end of the specimen is ignited and the subsequent burning behavior of the specimen is observed to compare the period for which burning continues, or the length of the s

Closed

19-00881

Plastics and Polymers

Industrial Laboratory needed for ISTA Transportation testing of millworked architectural elements and construction materials.

Submit Response

19-00865

Plastics and Polymers

USA Materials Laboratory needed for of cross link density analysis on a polyester resin crosslinked with an isocyanate.

Closed

19-00860

Plastics and Polymers

Materials Laboratory for polymer testing of laundry liquid and laundry pods for identification and level on the polymers present in these consumer products. Some possible polymer can include polyvinylpyrrolidone, polyethylene imine, polyacrylates.

Closed

19-00827

Plastics and Polymers

Contract Polymer Laboratory needed for production of polyethylene furanoate (PEF) in gram scale.

Closed

19-00816

Plastics and Polymers

{Polymer Laboratory needed for Polyurethane rigid foam (2.5lb/ft3 density) certification to the following standards.

- US Coast Guard Code ARTICLE 183.114 - MIL-P-21929C - UL 94 HBF, UL 94 HF-1, UL 94 HF-2 - ASTM E-84 - ASTM E-96

Closed

19-00809

Plastics and Polymers

Polymer Laboratory needed for SASO PVC Testing edge band on PVC - polyvinyl chloride polymer- to show fulfimnent to Saudi Arabia technical regulation SASO 156-16-03-02

Closed

19-00791

Plastics and Polymers

Large Corporation needs Materials Laboratory for surface energetics testing with a surface tensiometer on several glass and polypropylene fibers They are approximately 10-20 µm in diameter.

What would be the approximate cost and time?

Closed

19-00788

Plastics and Polymers

Plastics Company needs Polymer Materials Laboratory for the following testing:

LT transmission EN 1794-2 Annex F Road traffic noise reducing devices - Non-acoustic performance - Part 2: General safety and environmental requirements

Color difference as per BS EN ISO 11664-4 Colorimetry

Closed

19-00777

Plastics and Polymers

Automotive Laboratory needed for polymer grades (resins) testing to multiple Automotive Standards ( Toyota, Nissan, Honda and BMW) including

Toyota test TSM0500G FMVSS302 DIN 75201

The firs thing I would like you to know is if you have all of them or if you could specify which one of them do you have?.

The second thing is if you could tell me which of these tests you perform to the thermoplastic pellets (material) and which of these you perform to the final piece made by the thermoplastic material.

I really appreciate your answer as soon as possible.

Thanks,

Laura Pico

Closed

19-00745

Plastics and Polymers

Materials Laboratory needed for ASTM Outgassing Testing 3 different products 1) 3M 560 Polyurethane, 2) 3M 94ET, and 3) Sikaflex 221 Outgassing per ASTM E-595 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environmentat 2 different test conditions: 1) as called out in specification (125 C at 5E-5 Torr), and 2) 50 C at 5E-5 Torr.

Closed

19-00732

Plastics and Polymers

Environmental Microbiology Laboratory needed for ASTM testing of Polyethylene PE film of landfill biodegradation application on a PE film as to ASTM D5569

Closed

19-00726

Plastics and Polymers

Materials Laboratory needed for ASTM Biodegradation Testing of PVC and PVC-ABS film according to ASTM D-5511 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions at 45 and 60 days.

Submit Response

19-00714

Plastics and Polymers

Polymer Laboratory needed for ASTM Biodegradation testing of polymeric film samples under (Aerobic & Anaerobic conditions to -ASTM- 6400/5338 and 5511 Standard), characterization in your lab. Please include price quotation.

Submit Response

19-00704

Plastics and Polymers

$5000 BUDGET APPROVED Materials Laboratory needed for flammability (Close to UL94 test) of our Polymer Matrix Electrolyte (PME) in a hood located inside a dry room. Our sample is sensitive to normal air. Flammability test using modified UL94 standard in a battery grade dry room condition for Polymer Matrix Membrane (PME) of 100 micron thick

Closed

19-00701

Plastics and Polymers

Materials Laboratory needed for fire properties and thermal conductivity testing of corrugated plastic products including: Thermal conduction coefficient: (EN 13165) ?D: 0.022W/(m.K) FIRE PROPERTIES: - Fire class according to EN 13501-1: Class E - Fire class 'end use' according to 13501-1: B-s2,d0 (steel deck) - Fire class according to BS 476-p7 (1997): Class 1

Closed

19-00675

Plastics and Polymers

LONG-TERM TESTING USA Polymer Laboratory needed by company working on a novel experiment to study polymer mixtures for material science research. Company and needs lab space that meets the standard safety requirement to test our system.

Closed

19-00652

Plastics and Polymers

Contract Analytical Test Laboratory needed for bead testing for the following ingredients (not dye)

Ingredients: Glyceryl rosinate, Beeswax, Rosin, Ethylene/VA copolymer, Lanolin, Triethanolamine, Hydroabietyl alcohol, Green 6, Violet 2

Closed

19-00648

Plastics and Polymers

India Contract Materials Laboratory needed for TiO2 and ZnO film testing by XRD,SEM and FTIR

Closed

19-00641

Plastics and Polymers

LONG-TERM TESTING Large Composites Manufacturer looking to forge a partnership with a certified laboratory that can give timely results on composite leaf springs (carbon and glass reinforced plastic) cycle and impact resistance testing on a regular basis. In addition, we are looking to evaluate impact on sample parts as well.

Closed

19-00624

Plastics and Polymers

Consumer Products Laboratory needed for harmful chemicals testing in the plastics packaging of a headphones product that comes in a plastic tube. We are possibly changing vendors and want the new plastic tested for it's chemical makeup. But mainly would like to know if there are harmful chemicals in the plastic. Let me know what can be done and cost. Thank you,

Corey

Closed

19-00615

Plastics and Polymers

Materials Laboratory needed for PET Laminate testing for UL94 certification (ASTM E85), and NFPA-286, for use in decorative furnishings and wall coverings in addition to adding an FR additive for this type of PET product that would help us pass the Flammability and Smoke Spread tests to achieve UL94 rating (V0, V1, or V2)? And also see if we can achieve AHJ approval with a Class 1/A, or B, or C rating in ASTM E-84).

Closed

19-00590

Plastics and Polymers

Materials Laboratory needed for ISO testing to ISO 1856 Flexible Cellular Polymeric Materials - Determination Of Compression Set

Closed

19-00536

Plastics and Polymers

Construction Laboratory needed for weathering testing for plastic tiles. The test must include the affect of sun ray specially the UV ray on the tiles, along with the affect of heat and moisture on its properties. I would like to get an approximated result of the product's age. Potentially done to ISO 4892 or ASTM D4329-99

Closed

19-00504

Plastics and Polymers

Polymer Company needs Materials Laboratory for refractive index testing at difference wavelength? 1100nm, 1306nm, 1550nm

Closed

19-00472

Plastics and Polymers

Polymer Manufacturer needs Polymer Laboratory for Polystyrene Analysis through polymerization process from monomer to polymer. 1-we need international certification of ESCR Grade , for our HIPS (High Impact polystyrene ) which is ESCR grade. 2- Resistivity of our HIPS to Cyclo Pentene, polyols and other solvents use in refrigeration industry. As from our raw materials refrigeration industry makes liners of refrigerator , so we need certificate Resistance to these chemicals.

Closed

19-00469

Plastics and Polymers

Asia Materials Laboratory needed for polyurethane foam testing to the following standards: ASTM C518 Thermal Conductivity Of polyurethane Foam, ASTMC1058 test for Foam, ISO 844 U Value of the system

Closed

19-00445

Plastics and Polymers

Third-Party Laboratory needed for EVA Foam Testing for physical and electrical properties: 1 Compression Strength, 2 Resiliance property for Impact Energy 73 J 3 Energy absorption for Specific Thickness (test specimen material thickness) 4 Elastic limit 5 UL 94 V0 6 Vicat Softening Temp, Rate B/50 7 Vicat Softening Temp, Rate B/120 8 Rate of Thermal Conductivity 9 Coefficient of Thermal Explansion (@ Condition) 10 Specific Gravity <1.1 g/cm^3 11 Moisture absorbtion rate (%) 12 Chemical Resistance (No impact on chemical contact). - Soap and water - 10% bleach solution - 3% hydrogen peroxide - 90% isopropyl alcohol - Ethanol. 13 Electrical Property (Dielectrical strength, Resistivity, Relative permitability) 14 Compression Set

Closed

19-00441

Plastics and Polymers

Polypropylene manufacturer needs Automotive Laboratory for testing thermoplastic pellets to automotive standards from Toyota, Nissan, Honda and BMW including: JCS-3305 TSM0500G TOYOTA JCS-C291 HES C206 HONDA BMW GS 97038 BMW TSM0503G TOYOTA DBL.5404.20 WSS-M4D932-B1 FORD GB-8410 TS-INT-001 NES-M0403 NISSAN NES N0161 NISSAN TSM0503G TOYOTA NES M0094 NISSAN BMW GS 52 011 BMW ESB-M25P4-A FORD GMW 15702 FMVSS302 NES N0301 NISSAN DN 75201 GMW32323 BSDM0505

Closed

19-00437

Plastics and Polymers

Construction Materials Laboratory needed for ASTM testing of a plastic sheet in accordance to ASTM E96, method B Standard Test Methods for Water Vapor Transmission of Materials and to have the water permeance measured in perms.

Closed

19-00408

Plastics and Polymers

Construction Materials Laboratory needed for ASTM rating testing of polyolefin products to ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials 25/50 rated. Would you please help provide a price quote, sample requirements and lead time to get test results once samples arrive in your lab please.

Closed

19-00372

Plastics and Polymers

Manufacturer needs Materials Laboratory for biodeqradation activity testing in natural rubber threads.For this analysis we are requesting to send quotation and how much sample quantity required for analysis.

In the meantime, do not hesitate to contact us with any question about our request.

Thank you for your prompt attention to this request.

Regards K.Ramesh R& D Engineer

RUBBERFLEX SDN BHD Lot 2,Kawasan perindustrian bentong, Bentong 28700,Pahang darul Makmur, Malaysia. Tel: 609 222 4611 Fax: 609 222 5300

Closed

19-00370

Plastics and Polymers

Accredited Environmental Microbiology Laboratory needed for ASTM Biodegradability Testing of plastics to ASTM D5511. Determine Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions

Closed

19-00354

Plastics and Polymers

North American Cargo company needs UAE Polymer Laboratory for confirmatory testing to ensure that powdered form of a PET sample is the same as granular form. Polymer is Polyethylene terepthalate - material used to make plastic bottles.

Closed

19-00353

Plastics and Polymers

Materials Laboratory needed for NRC testing and fire rating of acoustical polyester fiber sheets.

Closed

19-00341

Plastics and Polymers

Microbiology Laboratory needed for MIC for polymeric sample for particularly E. coli, S. auerus, Mycobacterium smegmatis and C. albicans. The polymer has biocidal property, so the samples has to be evaluated for reduction in number of microbial colonies.

Closed

19-00322

Plastics and Polymers

Polymer Materials Laboratory needed for ASTM SIV and AAC testing in PET Plastics sample as per ASTM D 4603 and ASTM F 2013.

Closed

19-00316

Plastics and Polymers

Medical Device Laboratory needed for compatibility testing of medical devices, tyvec tubing and plastics for compatibility with chemo drugs

Closed

19-00297

Plastics and Polymers

Materials Laboratory needed for polymer analysis for HPLC determination of unreacted monomer and additive in a viscous liquid polymer. Specifically looking to quantify levels of an alkylphosphite in a polymer for a TSCA/PMN filing with EPA

Closed

19-00282

Plastics and Polymers

Materials Laboratory needed for testing the adhesion of a glue to ABS to ABS and ABS to Metal Clips including Clip Pull test, and Lap Shear Testing at 140F and -30F

Submit Response

19-00239

Plastics and Polymers

Aerospace Company needs Polymer Laboratory for ASTM Polyurethane testing: ASTM D4274 Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols or ASTM E222 Standard Test Methods for Hydroxyl Groups Using Acetic Anhydride Acetylation or ASTM E1899 Standard Test Method for Hydroxyl Groups Using Reaction with p-Toluenesulfonyl Isocyanate (TSI) and Potentiometric Titration with Tetrabutylammonium Hydroxide A

Closed

19-00237

Plastics and Polymers

Automotive Laboratory needed for General Motors Corporation GMW Testing of ABS sheet to GMW16853 Comprehensive Standard for Overall Emission Testing of Interior Materials and Parts (Fogging, Odor, Emissions, Carbonyls, Amines)(odor, fogging, emissions).

Closed

19-00222

Plastics and Polymers

Materials Laboratory needed for ASTM Testing of Relative Viscosity for Nylon Polymer Pellets and Zip tie samples per ASTM D789.

Closed

19-00217

Plastics and Polymers

OPEN TO LOCATION India Chemical Company needs Materials Laboratory for testing for a Phenol resin project where they need to analyse Flow Distance, Gelation Time and Softening point of Phenolic resin.

If you can perform the study according to ASTM standards, please let them know the slot availability and price details.

Closed

19-00206

Plastics and Polymers

Polymer Laboratory needed for impact strength and UV additive testing of Styrene material.

Closed

19-00197

Plastics and Polymers

ISO17025 Certified Test Laboratory applying GLP standards for full analysis of Poloxamer 338 according to Pharm Eur monography for Poloxamers

Closed

19-00188

Plastics and Polymers

Accredited Laboratory needed for ASTM Biodegradability testing of Polyethylene PE films after changing the additives for the film properties. Please provide test price and time .

Closed

19-00181

Plastics and Polymers

Toxicology Laboratory needed for ISO Genotoxicity testing a silicone part ussed in a medical application to ISO 10993 (Body contact: Tissue / Contact Duration: B - prolonged)

Closed

19-00165

Plastics and Polymers

Materials Laboratory needed for phenol formaldehyde testing to include the following 10 tests 1.specific gravity 2.water absorption 3.tensile strength 4.compressive strength 5.impact strength 6.thermal expansion 7.Moulding temperature 8.dielectric strength 9.refractive index 10.inflammability

Closed

19-00158

Plastics and Polymers

India NABL Materials Laboratory needed for materials analysis on 10 types of phenolic resins.

Closed

19-00154

Plastics and Polymers

USA Materials Laboratory needed for Oxo-Degradability Testing on multiple plastic films by the following methods (but open to others)

? QUV Accelerated Weathering - ASTM D 5208-14 ? Heat-Aging - ASTM D 5510-94 (2001) ? Tensile Elongation - ASTM D 882-12 & D 3826-98 (2013) ? FTIR (Fourier Transform Infrared Absorption Spectrometer) ? ASTM D 5576 ? 00 (2013) ? Melt Index (ASTM D1238-13)

Closed

19-00150

Plastics and Polymers

Materials Laboratories needed to provide with some quotes for ASTM E595 testing on 1, 5, and 10 encapsulation resins and conformal coatings.

Closed

19-00139

Plastics and Polymers

BUDGET APPROVED Medical Device Company needs Materials Laboratory resin confirmatory testing of the parts used in 2 plastic disposable infusion sets.

Closed

19-00135

Plastics and Polymers

Materials Laboratory needed for ASME testing of plastic bags to ASME D6400 Standard Specification for Labeling of Plastics Designed to be Aerobically Composted in Municipal or Industrial Facilities

Closed

19-00131

Plastics and Polymers

United Arab Emirates Materials Laboratory needed for polymer film testing by Gel permeation chromatography .

Closed

19-00108

Plastics and Polymers

Large Chemical Company needs materials laboratory conduct a study of the physical properties of polyurethane samples before, during, and after an oil soak, in both lubricant and diesel oil, at 140 degC.

Closed

19-00103

Plastics and Polymers

Contract Sterilizer needed for sterilization and validation for plastic procedure tips for Sterrad low temp sterilization.

Closed

19-00087

Plastics and Polymers

University Researcher needs USA Materials Laboratory to measure the refractive indices of 8 polymer samples at various wavelengths. The polymer samples are 2cm*4mm*2mm dimension and are made of vinyl and thiol organic monomers.

Closed

19-00076

Plastics and Polymers

FDA GMP Packaging Laboratory needed for USP testing of pharmaceutical packaging material as LDPE, HDPE and different blister like PVC,PVDC, Aclar and Alu/Alu as per USP general chapter 661,662 and 671

Closed

19-00059

Plastics and Polymers

North America GLP Environmental Laboratory needed for conducting studies of several EPA Registered insect repellent formulations to determine whether there is any plasticizing or degradation of Fishing Lines, Other Synthetic Materials, gear and equipment, plastics and fabric.

Closed

19-00046

Plastics and Polymers

Materials Laboratory needed for ASTM and ISO oxygen transmission rate of flexible plastic film barrier materials to ASTM D3985 Oxygen Transmission Rate (OTR) and ASTM D3985, ISO 15105 Oxygen Permeation of Flexible Barrier Materials Using a Coulometric Sensor

Closed

19-00043

Plastics and Polymers

Third-Party Laboratory needed for environmental simulation and packaging testing of new foam composite packaging materials made from wood and nanocellulose. drop test, humidity (climate) test to measure the amount of moisture adsorption using the humidity chambers and the compression test. Please give us a cost estimation of these tests also how long time it takes for each test? What are the sample size and quantity requirements for the drop test, compression test and the climate test?

Closed

19-00006

Plastics and Polymers

LARGE CORPORATION NEEDS ELECTRICAL LABORATORY FOR COMPLETE PVC ELECTRICAL TAPE TESTING

Closed

18-01928

Plastics and Polymers

Materials Laboratory needed for Nitrile Glove Testing to Chemotherapy Drugs and Concentration ( Tested for Resistance to Permeation by Chemotherapy Drugs as per ASTM D6979-05 Standard Test Method for Polyurethane Raw Materials: Determination of Basicity in Polyols, Expressed as Percent Nitrogen

Closed

18-01917

Plastics and Polymers

Polymer Laboratory needed for Intrinsic Viscosity IV testing of PolyEthylene Terephthalate PET resin material.

Closed

18-01910

Plastics and Polymers

Polymer Laboratory needed for semicarbazide testing on polypropylene bottle caps.

Closed

18-01906

Plastics and Polymers

Polymer Laboratory needed for migration testing of polypropylene film as per standard IS-10910. Product is being used in flexible packing such as confectionery, bakery product, biscuit, chips, chocolate etc

Closed

18-01904

Plastics and Polymers

Consumer Products Safety Laboratory needed for Human Repeat Insult Patch Test HRIPT Study. Please provide cost.

Closed

18-01878

Plastics and Polymers

ISO 17025 Forensics Laboratory needed for failure investigation analysis of PET preforms. One PET preform has a grey shade and another PET preforms has a pink shade. Both preforms made from the same materials. Pink preforms overheated at the temperature that grey preforms not. In this case we think that investigation of carbon content in both preforms will help us to find the cause of problem.

Closed

18-01871

Plastics and Polymers

Footwear Company needs Consumer Products Laboratory for durability, flex and wear(with accelerated cycle) insoles footwear testing on polypropylene arch support

Closed

18-01832

Plastics and Polymers

PROCESS DEVELOPMENT Polymer Laboratory needed for working on a project that wants to create an optimized process of polyurethane injection, that´s including the simulation using finite elements, but we are stopped in the characterization of the foam for the input data in the software.

Closed

18-01831

Plastics and Polymers

Life Science Company needs Laboratory for standard assay evaluating the efficacy of a compound for nematode (M. incognita) inhibition. Method example; The effects of selected compounds on hatching were assessed with M. incognita in 96-well microtiter plates. Eggs (ca. 50 per well) were incubated at 26?Cin45mgmL-1 in ADW of Frac- tion F, Compound 1, or citric acid standard. Control eggs were incubated in ADW. Each treatment plus control was replicated 5 times in each of two experiments except for Compound 1 (limited quantity allowed use in experiment 1 only, 4 replicates). After 8 days (experiment 1) or 7 days (experiment 2), all J2 that hatched during the incubation periods were counted and scored for mobility (see below). Data were pooled within treatment across both experiments (N = 10 for all treatments except Com- pound 1, N = 4)

Closed

18-01819

Plastics and Polymers

Laboratory needed for OECD or ISO biodegradability testing of Flexible Polyurethane Foam for applications in footwear.

Closed

18-01816

Plastics and Polymers

Automotive Parts Supplier needs Materials Laboratory for Melt Flow Index analysis of a resins used in a plastic automotive part by Melt Flow Analyzer.

Closed

18-01797

Plastics and Polymers

Medical Device Company needs Microbiology Laboratory for ASTM Biodegradation of Plastic Materials to ASTM ASTM D5511 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions

Closed

18-01781

Plastics and Polymers

Food Company needs Microbiology Laboratory for anaerobic biodegradable testing on food contact plastic container

Closed

18-01772

Plastics and Polymers

Canada Laboratory needed for performing biodegradation testing of plastics.

Closed

18-01762

Plastics and Polymers

LONG-TERM TESTING US Plastics Laboratory needed for quarterly ASTM testing of thermoformed plastic food packaging with biodegradable additives for PP and PET to standard ASTM D5511-11 as required by our customers.

1.One treated PP sample - 19 gms (2-compartment tray) 2.One treated PET sample ? 10 gms (12oz PET cup )

Kindly send us your quotation, lead time and other inclusions/information needed. We would at least require a report every 3 months, if possible and a Certificate or Letter

Closed

18-01758

Plastics and Polymers

PRODUCT DEVELOPMENT Materials Laboratory needed for testing to certify a Plastic Child safety device to sell on Amazon. The device has already passed the initial pass on the prototype phase. Will need the first few hundred tested from a new mold manufactured in the US. I think 1 of every thousand to comply And to comply with Amazon.

Closed

18-01749

Plastics and Polymers

Pharmaceutical Company needs Packaging Laboratory for FDA and MHRA 16CFR1700.20 testing to some HDPE bottles and caps.

This products are a Pharmaceutical drug product (Rx) to be commercialized in USA. The child resistant test report will be reviewed by FDA in our application.  Our package is : PUSH, DOWN AND TURN - CLOSE TIGHTLY.  The packages will be used for solid dosage form.

Closed

18-01717

Plastics and Polymers

Polymer Laboratory needed for plastic masterbatch organopletic testing. Please provide a quote.

Closed

18-01698

Plastics and Polymers

Coatings Company needs Polymer Laboratory for ASTM testing on polyurethane based membrane to ASTM C836 Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course Please send me quotation and the sample requirements. Thank you,

Closed

18-01691

Plastics and Polymers

Third-Party Polymer Laboratory needed for ASTM physical testing on 0.5 thick, high density, rigid for the following:

Compressive Strength - D1621 Shear Strength - C273 Shear Modulus - C273 Tensile / Elongation D1623

Closed

18-01690

Plastics and Polymers

USA Automotive Laboratory needed for elastomeric part testing to Ford Spec WSS-M9P8-C. The testing is for elastomeric parts the testing is environmental testing.

Closed

18-01675

Plastics and Polymers

Large Construction Materials Manufacturer needs Industrial Laboratory for DIN testing of plastic polyvinyl chloride PVC gutter systems to DIN EN 607 Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing

Closed

18-01658

Plastics and Polymers

California Materials Laboratory needed for confirmation testing on cut rubber ties. The original test report was done in Australia and can be provided for reference.

Closed

18-01651

Plastics and Polymers

India Industrial Laboratory needed for for quality control certificate of analysis for PET flakes made from pet crushing and washing business prior to selling to buyer

Closed

18-01643

Plastics and Polymers

Automotive Laboratory needed for accelerated testing for our plastic nameplates. Duration of 2500 hours. SAE J2527 Performance Based Standard for Accelerated Exposure of Automotive Exterior Materials Using A Controlled Irradiance Xenon-Arc Apparatus

Closed

18-01637

Plastics and Polymers

Large Chemical Company needs Germany Polymer Laboratory for Investigation of Polymer Materials in view of material characterization according to USP <661> and Reference EPA method.

Reference method is USP , <661>: Container plastic.

- Analysis for Metals

Closed

18-01609

Plastics and Polymers

Experienced Medical Device Laboratory needed for ICH shelf-life study of a medical device made of 100% Silicone. While we have a shelf-life for the raw material, we would like to do this again with the final product. We would like to see how aging affects the silicone. We are looking for a laboratory that has experience with testing silicone for aging and that can help us set up a protocol.

Closed

18-01599

Plastics and Polymers

Sports and Leisure Manufacturer needs Laboratory for analysis of rubber foam material sample for chemical composition.

Closed

18-01584

Plastics and Polymers

Europe Materials Laboratory needed for penetrability testing for rubber stoppers according to European Pharmacopoeia

Closed

18-01583

Plastics and Polymers

Large Polymer Company needs Materials Laboratory for ISO or ASTM polymer testing to determine the acid value of an oxidized Ultra high molecular weight polyethylene (UHMWPE)

Closed

18-01563

Plastics and Polymers

Company needs Polymer Laboratory for Canada Certification Testing of PET to get pre-shipment verification for PET food grade .

Closed

18-01551

Plastics and Polymers

Materials Laboratory needed for ASTM testing of Coatings to ASTM E-1795 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings

Closed

18-01529

Plastics and Polymers

Materials Laboratory needed for ASTM Testing to determine the electrical properties of cured rubber to ASTM D 991, D 257 Standard Test Methods for DC Resistance or Conductance of Insulating Materials

Closed

18-01512

Plastics and Polymers

Polymer Laboratory needed for % ash testing for in HDPE bottles.

Closed

18-01508

Plastics and Polymers

Materials Laboratory needed for ASTM testing of rubber flooring to the following ASTM Standards: ASTM E648 ASTM E662 ASTM E1354 ASTM D2047 ASTM F1344

Closed

18-01497

Plastics and Polymers

Europe Materials Laboratory needed for waterproofing testing as per EN 13948: 2007 Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roof waterproofing. Determination of resistance to root penetration.. Please provide an estimate on cost.

Closed

18-01492

Plastics and Polymers

Materials Laboratory needed for failure analysis of plastic film used in agriculture industry that typically last 8+ weeks but is becoming brittle and tearing. We want to have two plastic films tested for ingredient constituents to compare good plastic with bad plastic.

Closed

18-01487

Plastics and Polymers

Gas Permeability on one polymeric geosynthetic barrier (HDPE). Gas Permeability (Oxygen, 23ºC, 1 atm) according to ASTM D 1434.

Closed

18-01471

Plastics and Polymers

FDA Food Laboratory needed for testing of food-grade silicone drinking straws for any FDA requirements including ROHS, BPA, heavy metals, lead, pthalates, etc.

Closed

18-01452

Plastics and Polymers

Materials Laboratory needed to determine the content and its percentages in flexible Polyvinyl chloride vinyl (pvc)

Closed

18-01427

Plastics and Polymers

Third-Party Laboratory needed for large scale flammability and other testing for a performance space including: CBC 2603.9 - Special approval. Foam plastic shall not be required to comply with the requirements of Section 2603.4 or those of the Section 2603.6 where specifically approved based on large scale test such as, but not limited to, NFPA 286 (with the acceptance criteria of Section 803.1.2.1), FM 4880, UL 1040 or UL 1715. Such testing shall be related to the actual end -use configuration and be performed on the finished manufactured foam plastic assembly in the maximum thickness intended for use. Foam plastics that are used as interior finish on the basis of special tests shall also conform to the flame spread and smoke-developed requirements of Chapter 8. Assemblies tested shall include seams, joints and other typical details

Closed

18-01410

Plastics and Polymers

Polymer Laboratory needed for quantitative composition testing (material identification) of 3 polymer samples

Closed

18-01378

Plastics and Polymers

Compression Stress Relaxation (CSR) SAE J2979 Test Method for Vulcanized Rubber and Thermoplastic Elastomer Determination of Compressive Stress Relaxation (CSR) Response

Closed

18-01367

Plastics and Polymers

Large Media Company needs food certified laboratory for leaching study testing of plastics single-serving coffee cup to give a detailed report about the type of plastics/any other chemicals and amounts of each.

Closed

18-01360

Plastics and Polymers

Materials Laboratory needed for FTIR microscopy analysis of coating defects, and determination of what the defect is. For example, if the defect is a fish-eye, what is the central spot composed of, e.g. not completely disssolved coating resin, pigment particle, silicone.

Closed

18-01338

Plastics and Polymers

Polymer Laboratory needed for ASTM testing of polymer additives to ASTM E2019 Minimum Ignition Energy (MIE). Testing for polymer additives (chemicals formulations) for minimum ignition energy testing.

Closed

18-01337

Plastics and Polymers

Polymer Laboratory needed for testing to determine the materials used in making a plastic product to determine if it is PA6 or PA66, Glass filled, Bead filled talk filled etc and what grade.

Closed

18-01326

Plastics and Polymers

Packaging Laboratory needed for spectral transmission testing on plastic containers to USP <671> Containers - Performance Testing

Closed

18-01314

Plastics and Polymers

LONG-TERM USA or Korea Polymer Materials Laboratory needed for ASTM Elastomeric Coating properties as per ASTM D6083

Closed

18-01307

Plastics and Polymers

Polymer Laboratory needed for deformulation of Polyurethane for individual diol component quantification and detail of additives, was, stabilizer, etc.. typically react with excess alcohol to depolymerize than GC or LC-MS. we can supply pellets and the solubles extract for component analysis

Closed

18-01296

Plastics and Polymers

Elastomeric Coating to ASTM D6083 Standard Specification for Liquid Applied Acrylic Coating Used in Roofing

Closed