Contract Laboratory has received the following incoming Laboratory Testing and Scientific Research Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Labs to perform their Laboratory Testing and Scientific Research. If you need a Laboratory, please Submit a Laboratory Testing Request. If you need assistance or have questions email us or call toll free 1-855-377-6821.
MULTIPLE TESTS Contract Laboratory needed for wind turbine testing for Mechanical Properties Testing and Analysis, a Cyclic Load Test, Dynamic Load Test for a wind turbine alternator, please contact me at your earliest convenience. Test needed for the AC and DC sides of the alternator.
LONG-TERM TESTING MULTIPLE TESTS MULTIPLE PRODUCTS USA Electrical Laboratory needed to run water intrusion testing per CS.00056 1.4.10 to an IP4K protection level. This requires special equipment that we currently do not possess and I would like to know how much money it makes sense to spend on this test to run in house.A few parameters:We would be doing all pre/post testingWe would provide all monitoring equipment for the DUTFixture envelope with DUT will be less than 12x12x12Warrants will be for 4 samples at a timeOver the life of the product we could expect to run this test anywhere from 8 to 25 times,
MULTIPLE TESTS Contract Laboratory needed for the following IEC Joint box testing
1. Temperature cycling test: EIA 455-20 / IEC 60794-1-C10
2. Humid heat test: IEC 60794-1 or EIA/TIA 455
3. Rain withstand test/ water immersion test: IEC 60068
4. Vibration test: IEC 60794-1 or EIA/TIA 455
5. Bending and torsion test: IEC 60794-1 or EIA/TIA 455
6. Tensile test; IEC 60794-1 or EIA/TIA 455
7. Drop test: IEC 60068-2-32
8. IP 66 as per IEC 60529:1989 + A1:1999 + A2 : 2013
Company needs Contract Laboratory for thermal testing job on containers for industrial batteries with fire retardant material that has very high thermal expansion characteristics. We are looking to accurately map out the thermal expansion characteristics of these containers, specifically how temperature effects the height of the container. The test set up will be similar to what is shown in the attached photo but in a thermal chamber. There needs to be a surface plate at the bottom, a height gauge with an indicator attached. The product will have a 35-40lbs weight placed on the bottom to make sure it's flat to the surface plate. The temp will be lowered to 60°F, allowed to equalize for at least 4 hours, then the height measurement will be taken. Then the temperature will be increased by 10°F, allowed to equalize for at least two
USA LABORATORY (Continential USA Only) MULTIPLE PRODUCTS MULTIPLE TESTS Electrical Laboratory needed for IEC testing of hybrid cable and overall jacket of the cable for the following tests according to IEC Test Standards: attenuation (dB) of an hybrid cable we after the damp test IEC 60068-2-30. Also this customer is requesting that the overall jacket of the cable complies with the Environmental Testing from IEC 60068-2-18.
CANADA LABORATORY (Montreal) Consultant pour une chaine de franchise et nous aimerions connaître les ingrédients et les proportions afin de reproduire un produit essentiel à la préparation des recettes et qu'on doit utiliser, selon le contrat de franchise. Nous aimerions également pouvoir prouver, en établissant la liste des ingrédients éventuellement qu'un franchisé n'a pas utilisé « notre » produit, et n'a donc pas respecté le contrat de franchise. Nous aimerions pouvoir prouver, en analysant un de ses produits, qu'il est en défaut contractuel.
USA LABORATORY MULTIPLE PRODUCTS Electrical Laboratory needed for life and reliability testing of two primary items: 1. Batteries - we are replacing cells manufacturers and need to qualify new supplier. 2. large 10 and 15 gallon extractors. We are looking for assistance in life and reliability testing.
Electrical Laboratory needed for IEC Testing of lightning rod to IEC 62561-1 Lightning Protection System Components (LPSC) - Part 1: Requirements For Connection Components . Please include the estimated time to get the test result. If possible, please divide the cost into the cost only for testing and other expenses.
Prompt reply will be highly appreciated.
BUDGET APPROVED ($25K - 50K) Electrical Laboratory needed for enclosure testing to UL 2043 Standard for Fire Test for Heat and Visible Smoke Release for Discrete Products and Their Accessories Installed in Air-Handling Spaces We will be providing sample test units that are roughly 12 W x 24 L x 6 D. We will have a unit like the attached image with a lid including a key lock for it. Here is a web link to more information about the enclosure that is like what we are looking at.
USA Electrical Laboratory needed for testing for investigation project where fire damage occurred. We need to perform a full test on an existing 20 amp 1 pole circuit breaker feeding the equipment that may have started the fire. We need to verify that this breaker is working as intended. Could you provide a proposal for this service? Do you collect the equipment by yourself or need a third party to collect it?
URGENT BUDGET APPROVED ($5,000+) MULTIPLE PRODUCTS MULTIPLE TESTS Large Power Corporation needs USA Contract Laboratory urgently to perform the following multiple tests on 20 varnish insulation over stator core segments:
1. Interlaminar resistance test Two segments are used to measure the resistance between them. Stack the two segments on each other and put under a pressure of 1.5 MPa +- 0.1 MPa. Segments shall be insulated from the press. Voltage is applied on a raised corner of each segment from which varnish has been removed. Therefore only 2 layers of varnish are tested. The average interlaminar resistance over the segment surface is measured with a ohmmeter.
Minimum interlaminar resistance criteria for the interlaminar resistance test: 10 000 Ohm.cm2 on at least 90% of samples 1 000 Ohm.cm2 on the 10% remaining
Electrical Laboratory needed for current surge test as per below condition This test is intended to demonstrate that externally grounded closures can safely conduct an accidental current surge on the cable through a controlled metal path to ground. The internal current carrying components shall with stand a current surge of 1000 Amps for 5 seconds.The test shall be considered to have passed if there is no visible damage to metallic parts.
Contract Laboratory needed for multiple tests after leaching and impurities removal of crushed battery powder: pH, temperature, pressure profile from the reaction and hazardous by-products assessment.
The testing will be conducted after the following procedures: 1. Leaching of crushed battery powder with sulphuric acid. 2. Impurities removal (Ti,Al,Cu,Fe) with hydrogen peroxide 3. Metal precipitation
USA LABORATORY MULTIPLE PRODUCTS USA Contract Laboratory needed for MIL STD semiconductor testing of 265 custom designed and manufactured diodes per 19500 and mil std 750 DEPARTMENT OF DEFENSE TEST METHOD STANDARD: TEST METHODS FOR SEMICONDUCTOR DEVICES. Testing similar to JAN S requirements
USA LABORATORY MULTIPLE TESTS Water Treatment Plant needs Environmental Chemistry Laboratory to conduct the following chemical, contaminants and radionuclides tests on water: .Volatile Organic Contaminants (VOCs)Synthetic Organic Contaminants (SOCs) Inorganic Contaminants (IOCs) Nitrate (NO3) Nitrite (as N)Asbestos, Radionuclides Radionuclides Total Organic Carbon (TOCS)/AlkalinityTotal Organic Carbon(TOC)
USA LABORATORY NEW PRODUCT DEVELOPMENT MULTIPLE TESTS USA Environmental Laboratory needed for analytical chemistry and microbiology testing of a new water treatment system developed for a group of villages. We are very confident in our design but wish to verify our confidence with tests to make sure we have not missed anything. We are looking to conduct the following tests on water samples collected from our well site: pH Dissolved Oxygen Nitrogen/Sulphur/Phosphorus/Chlorine Turbidity Copper/Zinc/Iron/Lead Arsenic E. Coli/Enterococcus Giardia Cryptosporidia
USA, CANADA OR EUROPE LABORATORY MULTIPLE TESTS USA, Canada or Europe GLP Certified Contract Laboratory needed for the following physical properties testing for a clear, liquid solution (ethanol-based) according to the most appropriate ASTM test methods
- Appearance - Color (Colorimetry) - Density - Boiling Point - Conductivity - Vapor Pressure - Viscosity
Europe Contract Laboratory needed for determining the properties of an optics we designed for a small single LED solar light already in production. The optics (a non-imaging optics) is moulded together with the front case of the product as a single piece in ABS plastic. Due to some production process instability we'd need to better understand its basic optical properties and have suggestions on how to limit defects.
Electrical Performance Laboratory needed for IEC Standard Class C fire resistance testing on solar module and to generate a fire test report for us. The fire resistance test shall be carried out according to the standard IEC 61730-2, and verify whether the solar module can achieve the minimum fire resistance class C.Should you need any further information, please do not hesitate to contact me. I appreciate your quick response. Thanks.
MULTIPLE TESTS North America Materials Laboratory needed for the following military-standard requirements testing of needle mat material:
Hot surface performance(Fusing temp > 1300F or no melting, no significant at 1200°F (650°C) shrinkage (max 5 %) also Flame spread and smoke-developed, Thermal Conductivity, at mean temp. at 25°F; 25°F;50°F (24°C) ;300°F (149°C) ;500°F (260°C) ;700°F (371°C) . At this moment, we are looking for a quote and the fastest possible time for these tests and how long time will take for tests.
ISO 17025 Contract Laboratory needed to subcontract the following battery testing:
1) lithium-ion battery cathode, anode and electrolyte characterizations such as XRD, XPS, SEM-EDX, MS, ICP-OES, etc.
2) vent gas analysis when a battery undergoes thermal runaway, something along the lines of combustion testing.
We would like both of the above-mentioned tests to be per ISO 17025.
MULTIPLE TESTS Contract Laboratory needed for analysis of tallow used for biofuels as per the following AOCS, ISO and ASTM Test Methods: . Sr.No Parameters Methods 1 Free Fatty Acid AOCS Ca 5a-40 (OLEIC) 2 Phosphorous ISO 10540-3 3 Sulphur ICP-AES Spectroscopy 4 Nitrogen ASTM D5762 5 Iodine 6 MIU(Combination of Moisture & Volatiles, Insoluble impurities and Unsaponifiable) AOCS Ca 2b-38(Moisture & Volatiles) AOCS Ca 3a-46 (Insoluble Impurities) AOCS Ca 6a-40 (Unsaponifiable)
If all the test is feasible, kindly send us the service offer quotation for the same along with TAT.
Contract Laboratory needed for OECD435 testing of strontium to determine if it is a skin corrosive 1A under CLP (H314: Causes severe skin burns and eye damage) without testing, but based on pH>11.5. For transport, pH is not considered, so we would like to test to define if we need to classify or not. In Europe we are already classifying it as corrosive for transport (UN3131); in Asia they don't (UN 3208 - by lack of corrosivity study results) and that causes marketing disadvantages in Europe.
So therefore our request for a study to define the corrosivity for once and for all. Only for transport - as the CLP rules continue to apply.
Sr reacts with water. The reaction is exothermic but not violently. So there is no problem accumulating explosive concentrations of H2 gas when working under the hood.
Contract manufacturer needs Automotive Laboratory for quoting on a large order of custom hinges (end use military application) first article inspection including longitudinal and transverse loading per FMVSS 206 Federal Motor Vehicle Safety Standard 205 ? Glazing Materials and SAE J934.Vehicle Passenger Door Hinge Systems
Large Corporation needs Contract Laboratory needed for characterization of test structures on 12: Complementary metal oxide semiconductor CMOS wafer:
- MOM cap leakage current at 25/85C (0-40V, <1pA noise floor), ~30 units - Reverse junction leakage/breakdown voltage (0-100V), ~30 units
Are you able to do this type of measurements? We can expand it to more but this are the highest importance for us.
Large Power and Energy Company needs Europe ISO 17025 Accredited Laboratory for ISO 21702 anti-virus testing using SARS-CoV-2 or equivalent 2) ISO 21702 method should be included in their accredited laboratory certification of ISO 17025 3) Anti-virus test should be done in accordance with ISO 21702:2019. Laboratory should be used SARS-CoV-2 or equivalent.
LONG-TERM TESTING Independent Contract Laboratory needed for semiconductor TEM and FIB analysis for 20 semiconductor samples/month. Our requirements are as follows.
1. Need regularly - few times a month to almost every other day. 2. Imaging features (holes and channels) from 20 nm to 1 nm. May require FIB sample prep. 3. Fast turnaround is crucial (2 days). Please provide pricing for different turnaround times also - it will be useful for other clients.
Large Electronics Company needs Electrical Laboratory for the UL maximum size high power kVA or current for single phase and three phase transformers for temperature testing at an elevated ambient of 50C in a chamber according to UL 1561Standard for Dry-Type General Purpose and Power Transformers
Environmental Laboratory needed for testing to support research study on multi-tracers in groundwater. In addition, we intend to analyze the occurrence of artificial sweeteners in order to determine anthropogenic-driven pollution in aquifers within urban settlements. As we establish the amount of samples to be analyzed, we would like to know if your laboratory can test for the following parameters:
Name of Artificial Sweetener Artificial Sweetener code Sucralose SUC Cyclamate CYC Saccharin SAC Acesulfame ACE Aspartame ASP
Upon confirmation response, we can send you more information regarding the artificial sweeteners analysis in order to submit
Independent Laboratory needed for SAAMI Chamber and velocity testing for 200 samples of a 12 gauge door breaching round according to Sporting Arms and Ammunition Manufacturers' Institute Saami's standard SAAMI Z299.2 Pressure And Velocity Of Shotshell Ammunition For The Use Of Commercial Manufacturers.
Start-up technology company needs Laboratory to re-conduct tests with hydrogen and high-voltage-current electricity (DC up to 600 V; 900 A). We would like to rent a lab that would provide adjustable DC up to 600 V and 900 A. One test will run up to five minutes. During the test high-voltage level (close to 600V) has to be maintained over the five minutes, but high-level amps are needed only for the first 10 seconds. We intend to rent the rooms for 2-3 days and run a couple of tests per day. The standard lab room size (min 30m2 / min 3m height) and conditions for the hydrogen tests will work. We will bring all the other assets and equipment required in the experiment. In addition to our team, we plan to hire independent scientists and specialists to measure energy efficiency and certify the results of the tests. Also, any
ISO 9000 USA Electrical Laboratory needed for testing 2 or 3 small (roughly 8 cubed max) devices which are 24VDC loop powered, and generate a 4-20mA output. We need them tested at about -30C, room temp, and maybe 70C, monitoring/logging the 4-20mA output throughout those temperatures. We also need a report generated to state the findings (output data) at temperature. Time is also a factor, so we would need to know how quickly this could all be accomplished and how much testing would cost. We would hope to be able to get units in your hands by mid-January if price and leadtime are acceptable. Please call to discuss any questions about this. Thank you.
I am looking for a Contract Laboratory for Acoustic testing performed on a QTY 5 Earphones H-87B/U type 2 Earphone per MIL-DTL-18239 REV. E for frequency response per Paragraph 3.4 ,3.4.1, 220.127.116.11 & 4.6.1 & Test Circuit Figure 4 & 6cc Coupler Figure 5 (see attachments)
3.4.1 One thousand (1,000) Hz sound pressure output. The normal sea level sound pressure versus frequency characteristics of the earphone shall be 103 ± 2 dB above a reference level of relative to 20 µPa (micro-Pascal) (0.0002 dyne/cm2) with 1 milliwatt rms power at 1,000 Hz applied to the earphone terminals, when tested in accordance with 4.6.1.
18.104.22.168 Sound pressure output versus frequency. The normal sea level sound pressure versus frequency characteristics of each earphone shall not deviate from the 1,000 Hz response by more than the v
Contract Test Laboratory needed for EPA and ANSI testing of earmuffs and earplugs we plan to source from two vendors and resell. Our understanding of the testing required is the EPA's 40 CFR211 Subpart B, which references ANSI S3.19-1974. We also need clarification of our responsibility vs. the original manufacturer.
Electrical Engineering Laboratory needed for the design and design verification for 10,000A as well as 7,000A panels according to IEC 61439-1/2 standard for low voltage switchgear and controlgear assemblies
Specification calls for IP54 panel & ambient temperature of 50 Deg C.
Can you support us on the design as well as commercial quote for the testing.
We are looking for a one off test capacitors for following standards: IEEE Stds: STD 18-2002 (Standard-duty ratings), Std 18-2012 (Heavy-duty ratings), Std 18-2012 (Extreme-duty ratings) Capacitors we need to test: 200KVAR, 7200 VAC, 60HZ, 95kV BIL, heavy duty and/or extra heavy duty capacitor cans. We could also use 300 KVAR units with same technical information.
START-UP New Energy Efficiency Company needs Electrical Laboratory to run studies to show Effective Power Consumption (kWh) of electrical equipment with and without device usage. The goal of the device is to help reduce electricity costs by eliminating losses associated with the transfer of power from the power source to the end user device.
Objectives: 1. We need to test and verify how much the effective power consumption (kWh) of an electrical equipment decreases by when device is installed. - When the power factor of a load (with starting PF of 0.6/0.7/0.8/0.9) is raised to 0.95 after devices is installed. 2. We need to measure the extent to which the harmonics are stabilized, and if/how this affects the overall reduction of power consumption. 3. We need to figure out how much reactive power is reduced for each device that i
$10,000 BUDGET APPROVED Energy Company needs Electrical Laboratory for comparison of test devices before and after Irradiance: ZM1 x1 Dimension: 8 x 7 x 4 MM3 x1 Dimension: 10 x 6 x 5 UM3 Kraken 1 x1 Dimension: 5x 5x 4 UM3 Kraken 2 x1 Dimension: 7x 7x 3
Test evaluation: No evaluation during the testing period. Just visually compare before and afte UV exposure
Cycle 6 (used for high irradiance exposures of coatings and plastics): Lamp - UVA-340 Typical Irradiance - 1.55 W/m2/nm Wavelength - 340 nm Exposure Cycle - 8 h UV at 60 (+/-3) °C Black Panel Temperature; 4 h Condensation at 50 (+/-3) °C Black Panel Temperature.
Total test duration: 90 days (=90x24=2160 hours)
Defense Laboratory needed for Chemical, biological, radiological, and nuclear CBRN material to be tested to NFPA standards NPFA 1991-16 Standard on Vapor-Protective Ensembles for Hazardous Materials Emergencies and CBRN Terrorism Incidents and NFPA1994-18 Class 1 Standard on Protective Ensembles for First Responders to Hazardous Materials Emergencies and CBRN Terrorism Incidents
Solar Energy Company needs Electric Laboratory for IEC Testing to IEC62561-7 grounding enhancing materials test Standard:IEC62561-7:2018 Test Section: Sec5.2: Leaching Test,(General elementals according to EN 12457-2),Fe,Cu,Zn,Ni,Cd,Co,Pb; Sec5.3:Sulphur determination ,<2%; Sec5.4:Determination of Resistivity? Sec5.5: Corrosion tests?
Environmental Microbiology Laboratory needed to grow bacteria in a controlled and sterile environment, which will then be used in wastewater treatment. All bacteria are group 1 and pose no harm to human health.
Looking for a laboratory with access to the following: 1. Very cold storage facility (<80 degrees C) for storage of inoculate 2. Incubator with sufficient space for several trays with broth mixture to be added 3. Autoclave for destruction of perishable materials after process is complete
Company involved in the lightning protection and grounding business would like Electrical Laboratory for IEC 62561-1 Lightning protection system components (LPSC) - Part 1: Requirements for connection components and IEC 62561-2 Lightning protection system components (LPSC) - Part 2: Requirements for conductors and earth electrodes
Industrial Laboratory needed for IEC Testing of overhead lines according to IEC 61284 Overhead lines - Requirements and tests for fittings. The following tests should be applied : 1. Visual test 2. Dimension and material examination 3. Clamp bolt tightening test 4. Tensile test
URGENT: Due to recent emergency storm conditions, company is seeking Laboratory immediately for investigational study of the quality of several metals used in steel towers including several ASTM chemical, mechanical and metallurgical tests including: Chemical composition analysis; Mechanical (tension testing); and Bending (shear strength and elasticity).
The test should be based on the following ASTMs:
a. ANSI/ASTM A 572 - 79 (Grade 50): Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Steels of Structural Quality; and b. ANSI/ASTM A 36/A 36 M-01: Standard Specification for Carbon Structural Steel.
Industrial Laboratory needed to perform the following IEC tests on resins: Relative permittivity, 1 Hz and 100 Hz (IEC 60250) Dissipation factor- 1 Hz and 100Hz (IEC 60250) Volume resistivity (IEC 60093) Surface resistivity (IEC 60093) Electric Strength (IEC 60243-1) Comparative tracking Index CTI (IEC 60112) CLTE, parallel and transverse flow (ISO 11359-2)
High Tech Firm needs Laboratory with a HALT and thermal chamber to conduct ALT thermal cycling tests We require the thermal chamber to be capable of a ramp rate of 5-10 °C/min and a HALT chamber capable of at least 45°C/min. IMPORTANT NOTE: Please provide dimensions and chamber availability for the month of August
Third-Party Laboratory needed for EPA testing of several semi-volatile organics to EPA Method 625. Testing is needed for a chlorine dioxide generator for NSF 61 certification. This is for a chlorine dioxide generating system for water treatment. The semi-volatile organics are: semi-volatile organics as below: CAS 31736-62-6 CAS 2588-77-4 CAS 3602-55-9 CAS 73286-69-8
Performance Laboratory needed for testing ten 60 Amp rectifier regulators at 80% load for 2000 hours. A testing rig will need to be created to hold the rectifier regulator and a fan that will be needed to cool the rectifier regulator to make sure it does not exceed 45°C. The three phase AC signal required to run the test will need to be about 94 Vpp and 360Hz to match the stator output at 3600RPM. The output voltage from the regulator will be around 12.6 to 14.2 VDC. For data acquisition, temperature, voltage and current will need to be recorded every hour.
Biofuel company needs Bioanalytical Laboratory needed for molecular weight determination of soluble protein fragments to help determine the type (pore size) of membrane to be used to concentrate the newly soluble protein fractions. There is a heavy salt background in the solution of urea and sulfate.
URGENT Large Industrial Machinery Company needs Materials Laboratory for impact, failure analysis and identification of the cause of filtration liquid turning yellowish with use of white felt bags used for filtrating liquids We need to understand the cause and if there's any impact to the liquids being filtered
Electrical laboratory needed with the capability for testing specialized circuit breakers at 600VDC, 16kA, 50ms duration. Inductance <30uH, 50uH, 100uH. Data acquisition: Voltage and current at source and unit under test. Response time <.20ms, sampling >20/ms. Please indicate what type of source you have (DC source, rectified AC, etc) and details including expected source and circuit inductance.
Electrical laboratory needed for IEC testing to the following 6 IEC Standards: IEC 61000-4-9,Electromagnetic compatibility (EMC) , IEC 60529 Degrees of protection provided by enclosures ,IEC 60255-27, Measuring relays and protection equipment ,IEC 61000-6-4, Rent Conducted RF Immunity?, IEC 61000-4-9,Electromagnetic compatibility (EMC) , CEL E4N 55022
LONG TERM TESTING Oil laboratory needed for ASTM testing of petroleum / petrochemical products to determine hydrocarbon types present in middle distillates via mass spectrometry (ASTM D2425) as well as testing for fluorine and chlorine via combustion ion chromatography (CIC) (ASTM D7359).
Electrical laboratory needed for electrical certification and acceptance testing of transformers, arresters, and switches including current transformers 72.5KV and 145KV MR 200-400-600-800-1000-1200/1/11/5; surge arrester 72.5 and 145 KV; central opening switch 72.5KV and 145 KV 3150 Amp; voltage transformer 72.5KV and 145KV; power switch tanks monopolar live tension for 145KV SF6 gas insulated; power switch tanks tripolar for dead tension 72.5Kv and 145KV SF6 insulated. China
Electrical communications laboratory needed for IEC 61537 Cl. 10.2-10.8 testing of cable tray and ladder systems with respect to the following:
1. SWL loading IEC 61537 Cl. 10.2-10.8 (and Annex D.1) (to residual deflection measured by instruments with a resolution of 0.5mm or better and a precision of 0.1 mm or better in all range of the equipment per cl. 5.9).
D.1 states Trays mesh, solid, perforated to use load distribution plates that are rectangular, 120 mm by 40mm with a tolerance of 1mm.
Large cabling company needs a laboratory for fire resistance cable testing to BS 6387 Cat C W & Z.
1) Copper conductor, Mica tape, XLPE insulation, LSHF Bedding, Galvanized SWA and LSHF final Sheath.
3) Copper conductor, Mica tape, XLPE insulation, LSHF Bedding, AWA and LSHF final Sheath. This cables will be tested as per ( BS 6387 Cat C W & Z ).
Automotive laboratory needed for ASTM D5500 (Standard Test Method for Vehicle Evaluation of Unleaded Automotive Spark-Ignition Engine Fuel for Intake Valve Deposit Formation) or D5598 (Standard Test Method for Evaluating Unleaded Automotive Spark-Ignition Engine Fuel for Electronic Port Fuel Injector Fouling) testing of a liquid. Quote and turnaround time needed.
Electrical laboratory needed for ASTM & IEC Testing of ground enhancing compound to IEC 62561 Lightning protection system components 1. Leaching test - Based on EN12457 - 2 Part 2 and EN - 12506 2. Sulfur test - Based on ISO 4689-3 : 2004 3. Determination of resistivity : ASTM G57-06 4. Corrosion test - Based on LPR method (Linear Polarization Resistance Method)
Research laboratory needed for optimization study on ozonators used for water treatment to define the optimal ozone amount for treatment of customer's water including chemical analysis of water to calculate how much ozone we need to decrease quantity of needless organic and inorganic compounds to acceptable level.
LONG-TERM TESTING: Renewable ENergy company needs Environmental laboratory for environmental monitoring stack analysis on regular interval Source emission (PM, SO2, NOX), HCL, CO, NH3, TOC, HF, CD Th their compounds, Hg and their compounds, Sb As Pb Cr Co Cu Mn Vi their compounds, Dioxins and Furans.Kindly provide detailed quotation for sampling and analysis for the same.Looking for positive and quick reply.
Oil Laboratory needed for product development testing of diesel and gasoline additive combination with methanol. Previous studies showed the Binding of the emulsion proved elusive plus other problems were hard cold starts, check engine light, corrosion, swelling of fuel system seals and poor fuel mileage.
URGENT Oil Laboratory needed for American Petroleum Institute API light, medium, heavy and extra heavy oil testing. Need 15 samples analyzed 5 initial, 5 mid level refinement; 5 final refinement. What volume is needed. What is the cost. This is going into a pre-approved contract today.
Large aerospace company needs laboratory for SAE fuel system testing to 3 SAE Standards: SAE J2260, Non-metallic Fuel System Tubing with One or More Layers, SAE J2044 Quick Connect Coupling Specification for Liquid Fuel and Vapor/Emissions Systems and SAE J2045, Performance Requirements for Fuel System Tubing Assemblies
LONG-TERM TESTING Analytical Chemistry Laboratory needed for qualification testing to determine inhibitor (MeHQ) and PTZ (Phenothiazine) in acrylates by HPLC. We expect to have 2 samples ready for this test the week of 11/14-18. These first two samples are to qualify us for a major customer, and it will be ongoing work.
Electrical Laboratory needed for conformance testing of automotive spark plug cables: ISO 3808 (or SAE J2031) for Spark Plug Cable. ISO 3808 or SEA J2031 when imports ?Spark Plug Cable?. There are two kinds of Spark Plug Cables need to get tested, 5mm (in diameter) cable and 7mm (in a diameter) cable. ?Spark Plug Cable? is component part of ?Spark Plug Cable Set? that comes with connector plugs On both end of cables, But we only need test data for cable part only, not on ?entire spark plug cable assembly set?. QT Request: If possible, I would appreciate you qt me following 3 versions. ISO 3808, SAE J2031 and Partial Test of ISO 3808.(9 testing categories) (Most likely, I like to test with most reasonable way) . ISO 3808: 5mm Spark Plug Cable 7mm Spark Plug Cable: SAE J2031 5mm Spark Plug Cable 7mm Spark Plug Cable Partial Test for ISO
Laboratory needed for multiple tests on Oil Cooling System including crash, vibration, contamination, fire, oil leakage, thermal cycling, etc:
1. Temperature & latitude test as per DO 160 Section 4 Category -B3.
2. Temperature Variation test as per DO 160 D Section 5 Category-A.
3. Fluid Suceptability test as per DO 160 D Section 11 Category-F.
4. Humidity test as per DO 160 D Section 6 Category-C.
5. Fungus test as per DO 160 D Section 13 Category-F.
6. Salt Spray test as per DO 160 D Section 14 Category-S.
7. Water Proofness test as per DO 160 D Section 10 Category-S.
8. Icing test as per DO 160 D Section 24.
9. Operation shocks & crash safety test as per DO 160 D Section 7 Helicopter Category.
10. Constant Acceleration test test as per MIL-STD-810 Method 513.5.
11. Vibration test as per DO 160 D Sec
Oil laboratory needed hydrocarbon testing with it's interaction with various solvents an process streams including analysis of hydrocarbon solutions with elemental sulfur. Also, sulfur purity tests and the ability to work with pure elemental sulfur and its interaction with various solvents and process streams.
Materials laboratory needed for NATO coatings testing of chemical agent resistant coating (CARC) to North Atlantic Treaty Organization NATO AEP 64 standard fo Performance Requirements for Paint Systems Resistant to Chemical Agents and Decontaminants, for the Protection of Land Military Equipment and 65 coded Standard, described as Performance Requirements and Test Method for Paint Systems Resistant to Chemical Warfare Agents, for new new coating project to:
Screening Test (Resistance to Tri-n-Butyl Phosphate) onAluminium Alloys: 2024-T3 unclad, 5083 and 7020-T8
Optical Characteristics: *Visual comparison of the colour of the paints *Specular Gloss *Colorimetry on Aluminium Alloy 5083 or 7020-T6 and Steel
Scratch Hardness on Aluminium Alloy 5083 or 7020-T6 and Steel
Flexibility (Cupping test) on Aluminium Alloy 5083 or 70
Materials laboratory needed for thermal conductivity testing of thermal paste used in computers, and we need to measure the actual thermal conductivity for the sale of goods. Currently developed several modifications to the calculated thermal grease thermal conductivity in the range of 0.7 - 6 W / (m * K).
Large petroleum company needs materials laboratory for ASTM Testing of terephthalic acid to ASTM methods
ASTM D8031-16 ? Acid number for TA by potentiometric titration ASTM D1209-05 ? Color of clear liquids (Pt- Cobalt Scale)
- Cost/analysis - Turnaround - Sample amount required
Laboratory needed for Feasibility study for syn-gas production using a new catalyst, Catalytic activity of NixA1BEA and NixSiBEA. Fixed bed reactor with a fixed total gas flow run until catalyst activity is significantly reduced First test: a 2:1 molar ratio CH4 and O2 Second test: a typical LNG gas run with similar carbon ?C? to O2 molar ratio Third test (optional): a typical natural gas mixture with similar carbon ?C? to O2 molar ratio We only provide the catalyst
Oil technology development company needs toxicology laboratory LC 50 and LD 50 testing with some controlled versions of HF acid. Essentially, the blends we want to test are compounds that control the acidity of HF and show an ambient pH value of as high as 4 or 5 in aqueous solutions.
We are interested to know if your firm can help us carry out this kind of testing to effectively prove that our controlled versions of HF are inherently safer than neat versions of HF acid.
We are looking for labs that can conduct both LD50 as well as LC50 testing for us.
Fuel system company needs laboratory experienced in aggressive fuel fuel system compatibiligy for chemical analysis of sour/contaminated gasoline to detect presence of the following: - POM plastic - stainless steel - flourocarbon elastomer - flourosilicon elastomer - 90copper-10Ni brass - copper conductor - conductor insulation (Electrisola I220) - filter mesh (we can give you a raw sample and/or maybe a more helpful description) An estimate of the relative amounts of contaminants would also be helpful.
Oil Laboratory needed for gas testing to be done on the gas sample with operating pressure 80 ? 124 Kg/cm2g & Operating temperature 152 Deg C (Temperature will become ambient due to equalization with surroundings). . Please find the brief description about the Gas sample
Brief Description about Gas Sample : The well fluid is directly coming from the wells mostly consists of Condensate, Gas & H2O at operating pressure of 124 kg/cm2g & operating temperature of 152 Deg C. This Gas sample is from the common production manifold where well fluid from all the respective wells join and send to further processing.
Petroleum research & development laboratory needed for natural gas treatment research study. Our requirement is to check the efficiency of chemical for H2S Scavenging for crude natural gas. The natural gas stream contains H2S Concentration in crude natural gas is 150 PPM, The same needs to be treated by the chemical to achieve 0-5 PPM of H2S after treatment.
EPA Microbiology Laboratory needed for EPA microbiology testing. We are looking for EPA testing for heterotrophic plate counts, E. coli and Enterococci (preferably using IDEXX kits), and Vibrio cholerae testing. Samples would be collected from ship ballast water. We would like to specifically get information on labs in or near Vancouver, BC area as we would be shipping samples overnight from the Vancouver area.
ELECTRICAL CERTIFICATION LABORATORY NEEDED FOR POWER GENERATOR TESTING: EMISSION TEST, INPUT/OUTPUT TEST (WATTS - 50KVA), TORQUE/HP TESTCERTIFICATION AND ENVIRONMENTAL COMPLIANCE OF PRAE (PROCESS FOR REGENERATION AND AMPLIFICATION OF ENERGY) - GENERATOR THAT CAN EXCEED 100% EFFICIENCY.
URGENT Materials laboratory needed for physical and microbiology ASTM testing of tape bituminous wrapping tape used in petroleum pipelines Property Values Test method Tensile strength 12 N/mm2 BS 2782 Elongation 300 ASTM D 1000 Tear resistance >50 ASTM D1004 Adhesion to steel >2 ASTM D1000 Adhesion to Self >1.8 ASTM D 1000 Impact resistance >15J DIN30627 Dielectric strength >30000 total systemASTM D149 Insulation resistance2.5x1012 Ohm.cm ASTM D257 Water Absorption <0.1% ISO 62 Water permeability 0.01g/100inch2/24h ASTM F1249 Bacterial Growth - No Mic
Shipping vessel owner needs Spain laboratory for bunkered fuel analysis ?Asphaltenes, Ash, Carbon Residue ?Density, Flashpoint ?Sulfur Content, Hydrogen Sulfide ?Microbes Contamination ?Pour Point, Stability ?Total Sediment Potential (TSP) ?Viscosity, Water Content ?ISO 8217 Bunker Fuel Testing ?H2S Testing for Bunker Fuels ?Bunker Fuel Chemical Contamination Screening ?Chlorinated Compound Contamination of Bunker Fuel
EPA Environmental laboratory needed for bench-scale testing of a client?s wastewater treatment procedure. Client runs a metals finishing operation where they apply a chromate conversion coating to aluminum. Their wastewater is high in hexavalent chromium which they are able to remove by reducing it to Cr(III) and precipitating it as a hydroxide. Their current procedure seems to work well for this purpose. Recently they have been having some issues with high total cyanide results in their treated effluent, I suspect that the cyanide is coming from their chromating solution which contains potassium ferricyanide as an accelerant. Based on what I have read, the ferri- and ferrocyanide complexes can be difficult to treat since they are very soluble and are not amenable to chlorination. I did find some promising literature that suggests t
Large oil company needs electrical laboratory for electrical compliance inspections. At our facility we use hot sticks, release hooks, and other equipment for electrical repair would need certified inspections . Our protective gear and equipment that needs required certified inspections under NEC would be involved also.
Laboratory needed for DOT Jerrican (2.2-gallon portable fuel container) Testing per Department of Transportation (DOT) ?Subpart M: Testing of Non-Bulk Packaging and Packages CFR / I / C / 178 ? Specification of Packages, Sections 178.603, 178.604, 178.605, 178.606, 178.608 and 178.609
Large petrochemical company needs laboratory for measurement of the accurate density of a molten solid. The density of a molten solid (melting point of 185C) is needed between 195C and 230C. The density at 200C is approximately 1.14 gr/cc. It is estimated that the density at 210 will be ~1.13 gr/cc. The measurement ideally be good to three decimal points. Error limits on the measurement is also desired. Is the measurement even possible if the container used for the device expands at these temperatures?
Petroleum company needs NABL Accredited Laboratory for grease testing as per Indian Standards IS 507 : 1993 Grade 2 (https://law.resource.org/pub/in/bis/S11/is.507.1993.pdf) : 1. Glycerine content, percent by mass, MAX 2. Low temperature pumping properties 3. Water content, percent by mass, MAX 4. Corrosion preventive test, Max NABL Accredited Laboratory required.
Geology Laboratory needed to provide a bid for the following cor analysis : porosity and permeability analysis of 15 1x2 cores (we supply the core); two (2) of those samples will also have MICP analysis after initial P&P results; 15 thin sections from 1x2x.25 billet (supplied)
Energy company needs laboratory for fuel testing. I have three samples (Light Ends, Solvent, and Industrial Diesel Fuel) that would require the tests the following tests: ? Appearance (physical state, color, etc.); ? Upper/lower flammability or explosive limits; ? Odor; ? Vapor pressure; ? Odor threshold; ? Vapor density; ? pH; ? Relative density; ? Melting point/freezing point; ? Solubility(ies); ? Initial boiling point and boiling range; ? Flash point; ? Evaporation rate; ? Flammability (solid, gas); ? Partition coefficient: n-octanol/water; ? Auto-ignition temperature; ? Decomposition temperature; and ? Viscosity ? Reactivity; ? Corrosivity All three samples are petroleum based.
Description: Analytical laboratory needed for wide range hydrocarbon gas chromotagraphy to determine gas composition test on the natural gas coming from gas field for composition of the hydrocarbons right up to C16, the Gross and Net Heating Values of the gas, the Molecular Weight, the compressiblity factor and the adiabatic coefficient.
Analytical laboratory needed for wide rande hydrocarbon gas chromotagraphy to determine gas composition test on the natural gas coming from gas field for composition of the hydrocarbons right up to C16, the Gross and Net Heating Values of the gas, the Molecular Weight, the compressiblity factor and the adiabatic coefficient.
University Scientific Researcher needs Contract Laboratory for conducting science experiments for Research Study on comparison of synthetic oil to common crude oils. Methods for the conversion of lignites, subbituminous coals and other carbonaceous feedstocks into synthetic oil are researched. The results are expected to be compared to the results of other experiments.
Contract laboratory needed for radiation test in hydrocarbon samples. Below is some information about the samples
Propane samples ,which is a liquefied petroleum gas (LPG), will be pressurized hydrocarbons gas in liquid state. The samples are in a steel sample cylinder. Vapors samples, which is mainly consists of Methane, Ethane and a little of Propane plus, could be (or not) pressurized hydrocarbons in vapor or gas state. The samples are in a steel sample cylinder. Natural Gasoline samples, which is a liquid hydrocarbons in atmospheric pressure, are in a Boston bottles.
For Propane and 3 inlet vapor samples:
? Gross Alpha ? Gross Beta ? Radium 226 ? Radium 228 ? Strontium ? Thorium ? Uranium
For one liquid natural gasoline sample:
? VOC ? SVOC ? RCRA metals including Hg+ ? Radium 226 ? Radium 228 ? Gamma
INDIVIDUAL Oil laboratory needed to test to car engine oil for Oil quality, Oil age, approximate usage, . I would require a written statement into age of oil, how long approximately have been used, and test of quality? This is a Land Rover genuine part. I would provide sample of brand new oil vs a test to an oil used in the car to determine if they match?
H2S compatibility test for water based mud lubricant used in oilfield. Product needs to be exposed H2S gas to see the product's reaction towards the gas. Target is to see if the product is compatible and good to use in sour gas environment. I am looking for a quote for this test.
Australia university researcher needs laboratory for DHA (Detailed Hydrocarbon Analysis) test for commercial gasoline standard knocking test in CFR engine fueled by Australia 91 gasoline. In order to interpret experimental results, we want to get detailed composition information of the commercial gasoline. Hao
URGENT: USA environmental laboratory needed for two European Union studies on compound tetrakis (hexylmethyl)phosphonium sulfate (THPS), which they registered for use for bacterial control in recirculating water handling systems for wells associated with oil and gas pipelines We will need quotes for work on each of two studies as follows: 1 - A price quote for an EU Aerobic Biodegradability Study as described on Attachment #1; and 2 - A price quote for an EU N-Octanol Water Partition Coefficient Study as described on Attachment #2. We would appreciate receipt of these quotes by 3:00 pm on Thursday, December 10, 2015
EDUCATION PROJECT High School Science Students studying algae biofuel needs genomic lab that will test my algae culture to see if it is axenic or there are other organisms present.Please provide cost. As a student, cost is a very important aspect. The algae that I am using is Chlorella vulgaris UTEX 2714.
Environmental Laboratory needed for OECD biodegradability testing of water insoluble chemicals. (used in the oilfield industrythat require biodegradability analysis (OECD 301B: CO2 Evolution Test or other similar method). I would like to request a quotation for such testing Please contact me at your earliest convenience. I look forward to hearing from you.
FDA Food laboratory needed for food packaging contact surface testing of high quality kerosene normal paraffines n-Paraffin C13, which is used for rolling aluminum foil. As it is generally known foil can be used for packaging food, for that reason we need appropriate analysis of the substance(n-Paraffin C13) and certificate. So I kindly ask you to give information on following questions .Please tell the time needed for conducting the analysis FDA Packaging & Food Contact Substances (FCS). 3. Please tell the price for conducting the analysis. 4.How it is possible to get the FDA certificate? 5.What amount of the substance we should provide for the analysis.
Testing laboratory needed testing on fire arrestor caps which are used for gelled alcohol fuels and barbeque/fire lighter fluids.The objectives of this testing would be to determine the effectiveness of these fire arrestor caps in preventing flashback of flame into the plastic container and hence causing the container to catch alight.
Asia environmental laboratory needed for hydrocarbon testing.Soil and groundwater sample analysis:
? Total petroleum hydrocarbons diesel-range organics; ? Total petroleum hydrocarbons gasoline-range organics; ? Volatile organic compounds; and ? Semi-volatile organic compounds
and the following analyses for just soil samples:
? Arsenic, barium, cadmium, chromium, lead, mercury, selenium and silver; ? Polychlorinated biphenyls; and ? Pesticides and herbicides
ONGOING TESTING Independent Contract Lab needed for oil transformer sample testing of Electrical Transformer Oil Samples, The tests required are: Table-1: Tests & Test Frequency for Transformer Oil Analysis Sr. No. Test Transformer Type 400 kV TX 220kV TX 132kV TX 33kV EAT Transformer Catg. O A B C Standard Freq. Freq. Freq. Freq. 1. Breakdown voltage IEC 60156 1 1 1 1 2. Color and Appearance IEC 60422 1 1 1 1 3. Water content IEC60814 1 1 1 1 4. Acidity (Neutralization value) IEC 62021-1 1 1 1 3 5. DDF at 90°C including Resistivity IEC 60247 1 1 1 3 6. Interfacial Tension ISO 6295 1 3 3 3 7. Inhibitor content IEC 60666 1 1 1 1 8. Oxidation Stability (Induction IEC 61125 (B,C) 3 3 3 3 9. Oxidation Stability (Acidity and Sludge) IEC 61125 (A) 3 3 3 3 10. Particle Count IEC 60970 3 3 3 11. Flash Point NEN-ISO 2719 3 3 3 3 12. PCB's EN127
Materials Laboratory needed for ASTM Testing of a single oil sample for Wear Metals and Additive Elements to ASTM D-5185, Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
Middle East Laboratory needed for Sewage Testing of sewage samples for BOD,COD,PH,Oil/grease ,Total soluble solids,Total suspended solids,Phosphate,Ammonia ,Nitrogen,Total recoverable phenols Fluorides,Sulfides ,Chlorine,Disabled oxygen (DO),Hydrocarbons Floatables,Aluminum ,Arsenic,Barium,Boron,Cadmium ,Chromium Nickel,Mercury,Cobalt,Iron,Antimony,Copper,Magnesium Lead,Zinc,Most probable number of total coliform Most probable number of faecal coliform,Egg parasites,Worm parasites
Sludge analysis Arsenic Cadmium Chromium Copper Lead Mercury Molybdenum Nickel Selenium Se 100 Zinc Cobalt Total Coliform Faecal coliform Salmonella Viable Helminth Eggs Enteric viruses
Materials laboratory needed for propane testing for behaviors and properties of propane when pressure drops from 2000 bar to 300 bar, 80 bar, 50 bar and 3 bar within milliseconds, what the temperatures of propane would be within 0,5 milliseconds during this transitive pressure drop.
Materials Laboratory needed for ASTM Lubricant Testing to ASTM D4172 four-ball wear testing analysis. Lubicate will have "friction reducing concentrate" additive designed for all lubricant-based applications were wear and fatigue is a potential problem at all operating temperatures and needs to be lessened, alleviated, or guarded against. Needed to expand market to US and Canada so needed to be certified independent lab testing done in the area of wear analysis, i.e., ASTM D4172, et al. Could you please send a schedule of any wear-related lubricant analysis tests you perform, including pricing schedules, along with any other interrelated information.
Asia geotechnical laboratory needed for ASTM Borehole Drilling Core testing Cerchar Abrasivity Index (CAI)-abrasiveness for cutter wear during raise boring and drilling tools (blast holes) ? Multistage Triaxial Test in rock; ? Further UCS and point load tests; ? Further tensile strength tests. ? Triaxial testing of soils sampled from road alignment (R1-R10)
URGENT: Forensic Laboratory needed for natural gas testing for analysis of contaminants we are finding in our natural gas fuel at a power plant. These contaminants are black in color and are liquid, semi solid and solids. They are causing damage to jet engines. We need to identify the materials and possible sources. Samples are available now.
ISO / IEC 17025.2005 Certified Europe Laboratory with QA System to ISO 9001:2008, ISO 140001:2004) needed for Calcium Sulphite hemihydrate solubility limit (precipitation temperature) of the recirculation brine. I would like to request for a quotation including the following:
- Description of the testing procedure - Required brine sample (possibility of using seawater feed to determine the circulation brine precipitation temperature) - Required additional information - References in similar tests and other work at Sabiyah - Laboratory certifications - Price and planning
Thank you very much in advanced
Looking forward to hearing from you.
California materials laboratory needed for ASTM Materials testing of Phase Change Material (PCM) coolers. Humectants, Sodium Hydrates, Higher MW Paraffins.ASTM methods Melting Point, Heat of Fusion, Thermal Conductivity, Density using perhaps modulated DSC, Thermal Conductivity Meter, etc.
University Researcher needs Biotechnology Laboratory needed for biomass testing:Hydrogen and Nitrogen Analysis CHNOS analysis of two biomass ( switchgrass and tall fescue) Please send information about the amount of material which you need for this type test and price per each test.
Manufacturer of electric power connectors needs US laboratory for ANSI Testing to ANSI c 119.4,Connectors For Use Between Aluminum-To-Aluminum And Aluminum-To-Copper Conductors Designed For Normal Operation At Or Below 93 Degrees C And Copper-To-Copper Conductors Designed For Normal Operation At Or Below 100 Degrees C Please let us know how and where we can get this done in the USA.
URGENT: Environmental laboratory needed for water testing that has the capability to receive samples delivered from overseas, test samples urgently according to the list below and report results.
Samples from 2 sites in Asia would be sent twice per month for testing, perhaps for the next 6 months. The laboratory would need to arrange all logistics on arrival in their country to allow prompt analysis of the samples. Please supply a quotation for these services.
TEST UNIT SUGGESTED METHOD
pH Value at 25 deg C - APHA 4500 H+B
Conductivity @ 25°C ?S/cm APHA 2510
Total Suspended Solids mg/l APHA 2540 D
Total Dissolved Solids @ 180°C mg/l APHA 2540 C
Turbidity NTU ASTM D6855 / ISO 7027
Chloride mg/l APHA 4500 Cl -B
Sulphates mg/l APHA 4500 SO4²-E
Calcium mg/l APHA 350
Utility company needs laboratory for reliable condition assessment, investigation and IEC Testing on a utility transformer corrosive sulphur problem to assist us with understanding of our problem, assist with identifying causes and possible solutions. Various different test were performed on the oil (DIN, IEC and ASTM D 1275B). All test come back negative. (flash over in tap selectors) due to corrosive sulphur. Our problem is mainly associated with silver, therefore caused likely by the more reactive sulphur compounds. When we had the failure we took various samples to the CSIRO for test. CEM testing were performed and it was found that we have silver sulphide and copper sulphide on tap selector silver contacts. On LV brazed joints (silver used for brazing) there was also silver sulphide and copper sulphide. Both silver sulphide and cop
USA Materials Laboratory needed for development of an alternative to DGA analysis transformer oil testing for high levels of gas. We don't need to know exact concentrations in PPM, only if certain gasses (e.g. H2) are abundant (pass/fail). If levels are low, we move to the next transformer; if they are high we note that the transformer needs a full . Test Criteria: Performed in the field, small oil sample volume, immediate results, low cost, gas level specifics not needed (simple pass/fail test; fail status warrants full DGA) I understand that this is very specific and challenging and may not relate to any type of work or research you perform.
Laboratory needed for IEEE biofuel and biogas testing. Systematic experimental investigations are planned to study the thermal efficiency, fuel consumption, brake power and mechanical efficiency for 4-stroke C I engine for different loads and speeds. The experiment will be conducted by using 100% biodiesel and diesel blends the results will be compared and utilized to draw the performance curves.
Midwest laboratory needed for ASTM natural gas testing for electricity generation Once per year we collect natural gas samples in small cylinders provided by a lab. The lab analyses these samples by ASTM1945,Standard Test Method for Analysis of Natural Gas by Gas Chromatography D3246, and 3588.
California Electrical Laboratory needed for power switching box testing of: Short Circuit test to 10KA for an Auto Power Switching Box UL1008 approval but the samples failed the short circuit tests (close and withstand tests) at 5KA. The components themselves are rated min of 5KA; breakers are rated 10KA and Contactors are rated 5KA. I am building some other options by substituting the original components to diddferent components to find out the real reason for the failures. These samples were passed CE and I also received the CE certifications. Contact me and we will discussed further in details.
Large Energy Company needs electrical laboratory for electrical testing on grid system. Type Tests - ? Control Type Test?, Specified test will be performed on DUT as Grid proprietary set of cubicles called Overall dimensions and simplified list of I/O is provided on attached ADC Type Test setup.pdf document. Set of qualification tests is summarized in attached emc test list.pdf in three tables: EMC Test Summary table, Environmental Test Summary Table, Safety Test Summary Table. We are looking into startup of performing these tests in Novemeber 2014. Looking forward to your feedback, questions and availability of your test facility. Please contact me directly in case of any questions.
Environmental Consulting Firm needs Geochemistry Laboratory for material analysis on 2 samples . The first sample is what I think is fire brick with specific amounts of Alumina, Silica, and Oxides, am not familiar with a lot of the analysis techniques. So, I?m not really sure what I need done. The second sample is a loose bulk sample of ash. The ash came from the floor of a room in a buried archaeological site. We think this room was used as a rotary kiln dryer room in which they heated coal and wood to warm the air and dry clay. But, the room may also have been part of the adjacent clay storage building. It might be best to run a few smaller samples from within the larger bulk to get a range of results. Please call me if you are interested in working on this research with us. Right off the bat I?ll need to know how long analyzing these
Europe energy laboratory needed with environmetal simulation chamber for Solar Radiation Testing to According to MIL-STD-810G, method 505.5 Proc. II. OR According to Environment Condition appearing in Nature IEC 60721-2-4
Salt spray According to MIL-STD-810G, method 509.5.
This tests are to be performed on a sample of a Variable Message Sign. Maximum dimensions: 1000 x 1000 x 250 mm Material: Aluminium
We need urgently lab confirmation of availability to perform these tests and respective quotation.
Please also let me know the restrictions on dimensions of test chambers.
Europe analytical chemistry laboratory needed methane pyrolysis unit is to be tested with GC-MS for gas analysis and solid carbon for an analytical challenge We are supposed to assess the influence of different contaminants in the gas stream on the reactor performance and reaction products.
This means that we require analysis of the outlet gas composition and also analysis of the species adsorbed on the carbon catalyst from the reactor. The inlet (carrier) gas compositions is: carbon dioxide (up to 2-4 % vol or 33-66 g/m3) water vapor (up to 5,2 g/m3 or 30% RH at 20 C) N2: up to 28% vol or 327 g/m3 CH4: rest (> 67% vol or > 447 g/m3).
The list of contaminants is: Ethanol: 11 ppmv Carbon disulphide: 11 ppmv Tetrahydrofuran: 3 ppmv 2-methyl-2-butene 3 ppmv Toluene: 3 ppmv. In case of concentrations of contaminants being hard to me
Potable Water plant needs analytical chemistry laboratory for ASTM activated carbon testing for Atrazine - Microcistine - Geosmin removal of our Activated Carbon under ASTM D3860 norm,Standard Practice for Determination of Adsorptive Capacity of Activated Carbon by Aqueous Phase Isotherm Technique
China environmental laboratory needed for biomass testing and water testing: three samples which are primarily composed of biomass and water and also containing ethanol and acetic acid . We would like to analyze the samples using GCMS and/or LCMS to look for the possible presence of ppm quantities of Benzene Toluene Ethylbenzene Xylenes Phenol Naphthalene
Materials Laboratory needed for biodiesel testing of custom mixture of oil & clay slurry, it needs to be heated to 140F, stirred & checked for viscosity quickly before clay falls out of suspension, would like to send the sample in for testing, please advise if you can do this
Engineering Laboratory needed for physical Laboratory Testing of Concrete mixes: Density of Hardened Concrete Compressive Strength of Concrete Cube Compressive Strength of Concrete Core Making & curing of Concrete Cubes Slump Tests Air Content -Reinforced Steel. Steel Fabrication Testing
USA, Europe, UAE or Singapore Oil Laboratory needed for Heavy Fuel Oil Testing to check any adulteration along with testing for follwing prameters; (1) Strong acid number (mgKOH/gm), (2) Ash (wt%), (3)Gross Calorific Value (btu/lb), (4) Conradson Carbon Residue (wt%), (5) Flash Point, PMCC, (deg C), (6) Pour Point (deg F), (7) Specific Gravity, 60/60 deg F, (8) Sediments by Extraction (Wt%), (9) Sulfur (wt%), (10) Kinematic Viscosity, 50 deg C (cst), (11)Water by distillation (Vol%), (12) Hydrogen (%), (13) Wax (Wt%), (14) Asphaltene (Wt%), (15)Potassium (ppm), (16)Sodium (ppm), (17) Calcium (ppm), (18) Vanadium (ppm)
electrical Mechanical Laboratory needed for Abrasion testing: EN60068-2-70 (e.g. ABREX)abrasion test of totally four painted automotive samples (100 000 cycles, 100 000 cycles, 10 000 cycles and 10 000 cycles). I can provide test samples within 5 business days and expect assessment report including pictures (one common report is Ok). Please specify cost per test according to above cycle numbers.
USA Oil Laboratory needed for ASTM Testing to ASTM D130,Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test. ASTM D7095, Standard Test Method for Rapid Determination of Corrosiveness to Copper from Petroleum Products Using a Disposable Copper Foil Strip. 1 oil sample tested for determination of corrosiveness to copper.
Environmental Toxicology Laboratory needed for OECD Testing: Degradation OECD 301C 2 Fate and Behaviour in the Environment (IFF, 2005) Monitoring Study in Sewage Treatment Plants was performed under supervision of Royal Haskoning, supported by analytical work from Omegam Labs 3 Fate and Behaviour in the Environment OECD 314D 4 Degradation OECD 307 5 Fate and Behaviour in the Environment OECD 305 6 Fate and Behaviour in the Environment 1 year outdoor die-away in sludge-amended soils exposed to the elements. Levels below limit of detection after 1 year. Removal process undefined. < 1% leaching from soil.N2V2R2 Rel 2. (RIFM, DiFrancesco, 2002). 7 Long term toxicity to sediment organisms OECD Guideline 218 8 Long term toxicity to sediment organisms OECD 208 9 Long term toxicity to sediment organisms OECD 218