Contract Laboratory has received the following Laboratory Requests which need to be fulfilled! These Laboratory Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Labs to perform their Laboratory and Scientific Research. If you need a Laboratory, please Submit a Laboratory Request. If you need assistance or have questions contact us online or call toll free 1-855-377-6821. Please log in to see more.
Contract laboratory needed to run side-by-side comparison testing with three to five ship auger drill bits so we could see where ours stood in the competition.
We are looking...
Contract Laboratory needed for SAE testing of 25 male and female connectors used on a Fuel Oil or JP5 Jet fuel Purifier as per SAE-AS7413 Coupling Assemblies, Quick Disconnect...
Contract Laboratory with NADCAP Approvals needed for NASM Fastener testing of a part that has diameter of .7480-.7490 and a length of 1.860 inches as per NASM1312-13 Fastener ...
INDIA LABORATORY
India Commercial Laboratory needed for ASTM Testing via spectroscopy of O-RIngs to ASTM E1086:22 Standard Test Method for Analysis of Austenitic Stainless S...
USA/CANADA LABORATORY
MULTIPLE PRODUCTS
MULTIPLE TESTING
Materials Laboratory needed for a variety of fastener products testing for quality and performance in North America...
ASIA LABORATORY
Asia Physical Laboratory needed for bolt testing to determine the differences between grade 8.8 bolts and S45C bolt
Contract Laboratory needed for ANSI Testing of screws for the following on 1700 screws.
TEST METHOD: MAGNETIC PERMEABILITY SHALL
BE MEASURED IN ACCORDANCE WITH ASTM A342/...
ISO 17025 Accredited Laboratory needed for testing of AS85449/3 Saddle clamps per Table 1A and 1B except ozone test. Test has to be accredited by Nadcap ISO/IEC 17025 and AC70...
Industrial Laboratory needed for qualification testing of Dome Nuts to NAS1473
CANADA LABORATORY
Hardware company needs Contract Laboratory for comparison study of Shank Hardness of 12 different drill bits. Thanks in advance.
Consumer Products Laboratory needed for performance testing Zipper for Walmart
MECHANICAL LABORATORY NEEDED FOR TESTING OUR HEX BOLT AND NUT.
Mechanical Laboratory neededfor CSA testing of rubber (CR) gasket as per CSA B602 Mechanical couplings for drain, waste, and vent pipe and sewer pipe
EUROPE LABORATORY
Europe Contract laboratory needed to carry out high temperature tensile testing (around 300°C) as per customized requirements on metal screws.Minimum of fur...
Mechanical Laboratory needed for zerk fittings quality control hardness testing. The print calls for a microhardness spec and the vendor claims in-spec according to the print....
URGENT TESTING
MULTIPLE TESTS
Contract Laboratory needed for Thread Cutting Screws testing for the following :Surface hardnessCore hardnessDrill
MULTIPLE PRODUCTS
MULTIPLE TESTS
Contract Laboratory needed for standard test method testing on the bimetal connector and cable washer.
Aerospace Laboratory needed for AMS, Boeing and ISO testing of Tack Fabric that is Aerospace Material Specification AMS 3819C, Class 2, Grade A
INDIA LABORATORY
MULTIPLE TESTS
India Metallurgical Laboratory needed for all chemical and physical testing of metal door hinge.
MULTIPLE TESTS
MULTIPLE PRODUCTS
Large Company needs laboratory for the following EN Standard Tests for edging and seals used in transportation sector:
en6049 Aerospace s...
Contract Laboratory needed for certification testing on M12 stainless steel eyebolts including pull testing
USA LABORATORY
MULTIPLE TESTS
MULTIPLE PRODUCTS
Contract Laboratory needed for ASTM Comparison Testing on fittings to ASTM F1387 on two types of fittings. .
ASIA LABORATORY
Asia Laboratory needed for screw metal testing.
Contract Laboratory needed to perform an EIA Fretting Corrosion test for a custom connector EIA-364-110. It consist in introducing the connector with the device into a thermal...
Automotive Laboratory needed for SAE Testing for even-pin socket plug for car as per SAE J560 Standard test Primary and Auxiliary Seven Conductor Electrical Connector for Tru...
MULTIPLE TESTS
Large company needs Materials Laboratory for multiple ASTM and AATCC tests on hook & loop velcro product to the standard A-A 55126.there is multiple testing re...
USA MULTIPLE TESTS
USA Accredited Contract Laboratory needed for conducting all the tests for Hook and Loop Fastener Tapes (Velcro Type) in standard: A-A-55126x
as per t...
USA LABORATORY
LONG-TERM TESTING
MULTIPLE TESTS
MULTIPLE PRODUCT
Aerospace company will need Materials Laboratory for physical testing of different fastener parts such as ...
Experienced Laboratory needed for SAE testing of 11 PCs of sockets for SAE J560 Primary and Auxiliary Seven Conductor Electrical Connector for Truck-Trailer Jumper Cable
NADCAP Accredited Metallurgical Laboratory needed for NASM testing as per NASM 1312-13 made on Titanium alloy bars. The test as per NASM 1312-13 is normally made on fasteners ...
Contract Laboratory needed for Metallurgical analysis for failed bolts required.
MULTIPLE PRODUCTS
MULTIPLE TESTINGS
USA Metallurgical Laboratory needed for chemical content and alloy identification. of two parts including determination if the parts a...
Contract Laboratory needed for quality testing of Copper Nipples to find its strength, durability and the pressure rating.
Contract manufacturer needs Automotive Laboratory for quoting on a large order of custom hinges (end use military application) first article inspection including longitudinal ...
Contract Laboratory needed for testing and certification.of Aluminium Clamps in accordance with BS EN 62305:2011 Lightning Protection Standard.
Contract Laboratory needed for ASTM UV exposure testing for our bolts (15 samples) and weatherstrips (1 sample). to ASTM G154 Standard Practice for Operating Fluorescent Ultr...
Industrial Laboratory needed for cable compression connection testing on 750MCM cable with compression lug.
The test connections shall then be heated to 464 degrees Fahrenhe...
Laboratory needed for complete failure analysis of bolts that failed ASTM F3125/F3125M-15a, Standard Specification for High Strength Structural Bolts, Steel and Alloy Steel, H...
Construction materials laboratory needed for physical testing of Fiber Reinforced Polymer (FRP) Reinforcing Bar including 160 samples tested for durability in accordance with ...
Materials laboratory needed for screw DIN Testing: 1) Screw Type: DIN7500 PE M3X8
Properties Class: 8.8
Surface protection: DIN EN ISO9227-NSS 360h
Cleanliness requirement:...
Materials laboratory needed for DIN fastener cleanliness testing to Screw Type: DIN7500 PE M3X8Properties Class: 8.8Surface protection: DIN EN ISO9227-NSS 360hCleanliness requ...
Materials Laboratory needed for Adhesion tape testing for confirming Adhesiveness of tapes
International security lock company needs test of a Padlock per BS EN 12320 2012
MATERIALS LABORATORY NEEDED FOR ASTM TESTING OF HOOK AND EYE TO ASTM 5169 TESTING OF SHEAR STRENGTH OF HOOK AND LOOP
ASTM 5170 PEEL STRENGTH OF HOOK AND LOOP FASTENERS
Physical laboratory needed to Burst & Proof Pressure Testing to ASTM A234 WPB
Mechanical Laboratory needed for ISO mechanical testing to ISO 594 Testing of Conical Luer Fittings
1. Luer Assembly: Ensures that the Luer specimen can be assembled with m...
If your Laboratory or Lab Supplier is interested in quoting or finding out more about the above Laboratory Requests or the many others that we have, call us at 1-855-377-6821, e-mail us or view more Laboratory Requests