Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Plastics Laboratories to perform their Plastics Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Plastics laboratory that would like more information on these Plastics projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Physical Laboratory needed to perform weathering testing on our plastic according with VW standard PV 3930. Exposure time should be 1500 h. We do not need evaluation after test. Second specimen should be tested according with Nissan standard (NES) M0135: Table 3 Method 1-II-2 for 1000 h, without evaluation. Please send us an offer for these two tests. Thank you.
Laboratory needed for study on the compatibility of slotted HDPE pipe (for horizontal wells) through a groundwater contaminant plume over time and with variable temperature while injecting steam. The product is multi-phased, consisting of jet fuel, trichloroethylene and stoddard solvent.
LONG-TERM TESTING Packaging Laboratory needed for packaging testing of In flexible packing materials like double laminated , triple laminated & other flexible packaging material for: Flex crush resistance Water vapor transmission rate Oxygen transmission rate Optical density Lamination bond strength
LONG TERM TESTING Materials Laboratory needed for Polyamide Tube testing to prove compliance with DIN73378, DIN74324-1 and SAEJ844 Many different tests covering material mechanical properties, hydrostatic burst pressure, impact testing, moisture absorption, stiffness, cold temperature flexibility, chemical resistance, extractables, heat aging, thermal stability, artificial weathering and UV resistance.
Medical Device Company needs medical technology laboratory for packaging/ product /development of developing a disposable medical cable assembly that will require sterilization. ABS plastic housing for connectors Silicone vs PVC for cable assembly I have questions about cost, materials, packaging and logistics.
Accredited UK laboratory needed for construction building products testing of flexible sheets for waterproofing to BS EN 12691, Determination of resistance to impact BS EN 12730. Determination of resistance to static loading and EN 1847 for building products. Methods for exposure to liquid chemicals, including water
Construction Buildings Laboratory needed for ASTM Testing for Prefabricated Vertical Drains 1. Width ASTM D 3774 2. Thickness ASTM D 5199 3. Discharge Capacity qw , straight & folded ASTM D 4716 4. Tensile strength, elongation at break, elongation at 1kN (full width test) ASTM D 4595 5. Apparent Opening Size O95 ASTM D 4751 6. Permeability, permittivity ASTM D 4491 7. Grab tensile strength ASTM D 4632 8. Trapezoidal tear strength ASTM D 4 ...
Materials laboratory needed for ASTM Testing for compatiability of plasticizers to ASTM D3291 Testing (Standard Practice for Compatibility of Plasticizers...).Lab would need to accept samples of the plasticizer, and then formulate into the PVC, then perform the analysis.Approximately 10 samples.
Laboratory needed for quantitative analysis of DEHP and DEHT. Must extract a resin from peristaltic pump tubes and then within that resin find the DEHP and DEHT levels in ppb. The resin is approximately 3% of the tubing composition and the DEHP and DEHT is approximately 1% each of that.
e-liquid company needs packaging laboratory for packaging teting of glass and LDPE Plastic bottles to Title 16, Part 1700.20, Testing procedure for special packaging.We have glass and plastic bottles. Our plastic bottles are LDPE. We have 3 different caps and 12 bottle sizes.
Microbiology laboratory needed for microbiological testing of production facility including water testing and air testing of various areas around production lineincluding plastic closures, preforms and conveyors.. Microbiology testing to include mold/yeast, total bacterial, and coliform separately. Tap water in the production area will also be tested in the production area. How do you go about and do these test. Does one of your technicans ...
Accredited Food Laboratory needed for extractables and migration testing of Food grade (LLDPE Cling) film testing to U.S. FDA CFR 21 177.1520 clauses (c ) (2.1) Extractable fraction in n-hexanes Extractable fraction in xylene and FDA Migration on PE (Density; Melting point; n-hexane extractives or Xylene extractives) U.S. FDA CFR 21 177.1520 clauses (c ) (2.1) Cling plastic is intended for food wrapping application for contact with aqueous & ...
Materials laboratory needed for independent third party testing of laminate flooring for 1) Test for ortho phthalate plasticizers 2) Following tests with relevant ASTM test parameters (for vinyl flooring) - Stain and chemical test - Static load limit - Dimensional stability - ASTM 648 - fire test - ASTM 662 - smoke test 3) Following tests for EN / ISO parameters i) ISO 10581: Homogeneous Flooring including all the sub standards - ...
Polymer laboratory for PVC Testing. Test PVC powder its physical , chemical & identification test. 1) Identification of PVC 2) Viscosity, ml/g 3) No of impurity particle 4) Appearing Density, g/ml 5) Residual chlore thylene content ug/g I am providing details of test to be perform for PVC resin powder.
Exporter of rubber,plastic bathroom accessories needs physical laboratory for physical testing including prformance and biodegradability: 1 Tensile strength ISO 527 1 2 Elongation 3 Tear strength 4 Density / sp. gravity 5 Hardness 6 Breaking strength in fabric ASTMD 4632 7 Low temp. bending test in butyl mansjett D 2136 Chemical test for rubber, plastic comp ...
Materials Laboratory needed for Biodegradation testing of Plastics as per ASTM D5511, Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions and ASTM 5526, Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions etc..
Consumer Products Laboratory needed for ASCM (?) and the US Product Safety Commission testing child safety consumer panel testing of plastic grocery bag with locking mechanism that prevents children five and under from entering it. The bag also needs to be tested on adults to see if the can open and close it.
Contract Laboratory needed for microscopy on polymers for comparisons with image & measurements obtained with a Laserlec Optilec H1200 confocal microscope. Appears imaging software was used to discern the differences between the shading from the blended polymers & it calculated the average width or thickness of the different phases of the two blended polymers.
Third-party laboratory needed for biodegradability testing of plastic fishing baits for fishing potentially to ASTM D6691Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum as the most appropriate test.
Materials laboratory needed for rubber testing for Hexane extract, Thermal analysis (DSC, DMA, TGA) , EDX analysis (REM) of the material for heavy metals (Pb, Cr-VI, Hg, Cd), TDS-GCMS analysis of the material for softeners, Extractable matter (extration agent: n-hexane) % (Max) Tg (tan ? max) on sheet material (°C), Shore A Hardness on sheet material @ -40°C For 144 Hrs, Corrosion resistance @ 100°C for 24 Hrs.
Automotive laboratory needed for ASTM Testing and testing to norm MS211-47 Type A2 (KIA/HIUNDAI): ASTM D792, Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement , density, relative density, specific gravity, D638 - 14 Standard Test Method for Tensile Properties of Plastics , modulus of elasticity, percent elongation, plastics, Poisson&rsquo,s Ratio, tensile properties ASTM D790, Standard Test ...
Polymer Materials laboratory needed to conduct isothermal viscosity testing of sealants and estimate working life at various temperatures. I know this cannot done by regular Brookefield viscometers. At 75 F for 2 hours at 85 F for 2 hours 100 F for two hours 120 F for 2 hours 135 F for 2 hours 150 F for 2 hours.
LONG-TERM TESTING Clinical Central Laboratory processing blood and plasma needed for product development and optimization studies microfluidic devices and their components to study the effect or interference of devices on blood chemistry and overall specimen integrity. Initially, we would like to send a few samples (n=10) for a complete blood count (CBC) and comprehensive metabolic panel (CMP) to determine baseline values. After we have iden ...
FDA and GDUFA compliant Pharmaceutical laboratory needed for USP Testing performing the tests under new chapters <661.1> and <661.2> from USP 39, regarding plastic analysis. Please send a quotation at your earliest convenience. Thanks in advance for your support and looking forward for your reply.
Mechanical Laboratory needed for electrical and mechanical properties testing of 0.40 PVC Shielded cable with 8 22 AWG conductors , we need to get the measures for below: Measure below Mechanical Properties Minimum permitted bend radius Measure below Electrical Properties Conductor resistance @ -10, 20 , 60 deg C Insulation resistance core to core Shield resistance Mutual Capacitance core / core (symmetrical) Mutual Capaci ...
Consumer Products Safety Laboratory needed for General Product Safety Directive , GPSD EN 71-1, Mechanical and physical properties of Juvenile Products including: PAHs test (PVC) Formaldehyde test (textile) PCP test (textile) AZO Dyes test (textile)
FDA Food Laboratory needed for medium density polypropylene sheets testing to REACH, ROHS, and FDA foodcontact standards
Canada plastics laboratory needed for ASTM testing on tensile bars. The following tests we are interested in having done; Izod Impact (Notched) ASTM D256 Flexural Modulus ASTM D790 Plastics Tensile Testing ASTM D638 We are interested in getting a quote for the work. We have control bars, and two treatment groups of tensile bars for comparative purposes.
USA Materials Laboratory needed for Density testing according to ASTM D1505, Standard Test Method for Density of Plastics by the Density-Gradient Technique. Please provide me the following information: 1. standard & rush turn around time & fee 2. price 3. sample amount 4. Quality System (ISO 9001, GMP, GLP?)
Materials laboratory needed for DIN Testing of one rubber compound sample for testing: 1. DIN 53505 2. DIN 53507 3. VDA 675205 4. VDA 675303 5. VDA 675217
Mechanical laboratory needed that who does plastic film testing for mechanical properties.
India Laboratory needed for Mechanical Testing 1 Deflection temperature under load (1.80Mpa) ASTM D648 oC 2 Tensile Strength ASTM D638 M.Pa. Tensile Modulus ASTM D638 M.Pa. Elongation at break at 20 oC ASTM D638 % 3 Flexural Strength ASTM D790 M.Pa. Flexural Modulus ASTM D790 M.Pa. Our Samples will be Cured Unsaturated Polyester Resin.
Waste Management company needs USA physical laboratory for rubber pellet testing to determine how pellets react to burning at low temperature, electric induction furnace or crucible with the vacuum along with capturing and condensation of vapors
Third party laboratory needed for ISO testing of chemically cross linked foam for Ozone resistance as per ISO 1431, Rubber, vulcanized or thermoplastic -- Resistance to ozone cracking.
USA plastics laboratory needed for resin testing for Molecular weight determination for an oligomer resin
Microbiology Laboratory needed to test anti-biofilm activity of titanium discs uncoated and coated with a polymer. I need 3 assays with titanium discs uncoated and coated with a polymer to verify anti-biofilm activity for anaerobic bacteria involved in peri-implantite.
USA Materials laboratory needed for ASTM Testing for melt point determination to ASTM D789, and dimensional stability. My sample is type 66 molybdenum disulfide-filled nylon. Could you provide me the following: 1. Pricing 2. Standard and rush turn around time, and its fee.
India Laboratory needed for Poly tetra flouro ethylene testing to issue &certified authority products is free from Transmissible Spongiform Encephalopathy declaration.
Materials Laboratory needed for biodegradability testing of lab that an antifoam to determine if it is biodegradeable.
USA Materials Laboratory needed for ASTM Testing: gel content of polyethylene samples using ASTM D2765-11, Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics (xylene or Decalin extraction, boiling solvent, sample in wire mesh cage, weight loss after 6-12 hours in boiling solvent, then vacuum oven).
Polymer laboratory needed for molecular weight testing by mass spec analysis of the polymer. It is new inert ingredient submission to US EPA under their low risk polymer exemption rule.
India NABL accredited laboratory needed for abs and san plastic product materials testing
Materials laboratory needed for Thermal Conductivity testing of DIN EN ISO 8497 for our rubber insulation
Food laboratory needed for food contact surface testing for FDA 176.170 CERTIFICATION FOR OUR EMULSION POLYMER WHICH IS USED IN COATING THE BOARD USED FOR PACKAGING OF LIQUIDS like FRUIT JUICES We will be sending you the list of inputs in our polymer emulsion so testing may not be required.
USA Contract Laboratory needed to provide Polynuclear Aromatic Hydrocarbon (PAH) testing according to EPA 8310. It involves determining the concentration of PAH in ground and wastes using HPLC. The sample is graphite powder. Could you provide me the following information: Price per sample Minimal sample quantity Turnaround option (standard and rush, what surcharge) Shipping address
Materials laboratory needed for IEC electrostatic testing of polyethylene sheet to to IEC 61340-4-4, Electrostatics standard for its electrostatic properties.
FDA GMP Polymer Laboratory needed to assist to file GRAS and/or FCN for our product(s), as well as capable in conducting all the FDA required test in order to obtain the FDA approval on polymer product. Pls enlighten us on the details of phases/process, analysis, cost and lead time.
Contract Laboratory needed for testing to EN1621-2 Level 2, Protective clothing for professional motorcycle riders. Jackets, trousers and one piece or divided suits
Materials laboratory needed for f PROPYLENE GLYCOLtesting for appearance, PG content, moisture, density, index of refraction, acidity, distillation range, color (Pt ? Co).Please provide the price of this analysis? What the minimum amount of material and packaging is necessary for research sample?
Plastics Laboratory needed for ASTM Testing: Brittleness Temperature testing performed to ASTM D746 on thermoplastic urethane. I need baseline number so am looking at measuring 2 lots.
Materials Laboratory needed for analysis for total chlorine content on DVB-Styrene crosslinking gel samples.
Third-Party Microbiology laboratory needed for ASTM microbial degradation of Polyethylene using a multi-strain inoculum and searching for a third party lab to confirm degradation using ASTM D7475 ? 11.
URGENT United States Materials Laboratory needed for DBL 5404 Odour Test for PPT40 Grade Resin... Please provide cost of this test ASAP.
Manufacturer needs Consumer Products Safety Toxicology Laboratory for product safety and toxicology testing of fabric-based product.for - Cytotoxicity testing. - Sensitization testing. - Irritation or Intracutaneous Reactivity Testing - Specific testing on Urethane materials: 0 mmHg for 3s to 150 mmHg and hold for 3s for a minimum of 100,000 cycles.
Coatings Company needs polymer lab that can test National Fire Protection Association NFPA via ASTM D6668. Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 1 Samples are water based polyurethane resins.
Materials Laboratory needed for ASTM E84, Standard Test Method for Surface Burning Characteristics of Building Materials Lab testing quote for Flame Spread. One sample
Materials Laboratory needed for Thermal testing for BTU levels of bag house dust
Environmental simulation laboratory needed for accelerated simulation testing that simulates ocean shipping environmental conditions experienced shipping from Asia to us on the ocean. The material is a molded EVA that I need to understand dimensional stability before and after the shipment process. Please reply with contacts who could provide this in an accelerated manner. South east Asia based would be good. Thanks tom
Polymer Laboratory needed for polymer synthesis project
India polymer laboratory needed for quality control testing: Polypropylene sheet testing is required for judging its quality. we are planing to manufacture effluent treatment plant equipments from PP sheets.
Polymer lab needed for film testing that can run ASTM E 2178 but using CMU blocks instead of a thin film. The coating we are wanting to test is a water based air barrier which we are trying to certify to ABAA criteria.
Texas Materials Laboratory needed for Flash point testing
Plastics Materials Laboratory needed for Polytetrafluoroethylene PTFE Testing of PTFE UV transmittance in the 250 - 260 nm range Objective: To establish the % transmittance of a PTFE sample of : 1) 0.50 mm thick; Sample size = 1. 2) 0.30 mm thick; Sample size = 1. 3) 0.10 mm thick; Sample size = 1. Deliverable: A 1-to-2 page report in electronic format. The report should include methods and results. The results to be presented in a graph ...
Plastics (Plasticised PVC) flooring manufacturer needs physical laboratory for combustion analysis of condensate from manufacturing operation that produces condensate. I am interested to have this liquid evaluated for future combustion purposes i.e. a power train or oil heating system
Materials Laboratory needed for ASTM Testing of Erucamide slip counts in polyethylene pellets to ASTM D6953, Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC) or other test methods
University Researcher needs India materials laboratory for NiTi thin films of thickness 300 nm on silicon wafer size 1 cm x 1 cm. I need to characterize these samples using TEM. Please send the quotation.
Materials Laboratory needed for ASTM LEAP test as per ASTM standard ASTM D6499-12 (Inhibition ELISA.) to certify the product is latex free.
United Arab Emirates Materials Laboratory needed to test our plastic product Polypropylene granules for the following Composition *Appearance *Density *Melting point/Range *Melt Flow Rate *Ignition Temperature *Hazardous Status *Solubility *Molecular weight distribution
Middle East Plastics company needed for plastics laboratory for PVC and PPR Pipe testing for ISO International Certification
Materials Laboratory needed for ASTM Testing: Mullen burst test on rubber according to ASTM D751, Standard Test Methods for Coated Fabrics
Materials Laboratory needed for Ultra Violet testing of panels used for contact staining for rubber per ASTM D 925
Asia materials laboratory needed for Tensile strength and water resistance testing of crab shells bioplastics
India or United Arab Emirates FDA and ISO Materials Laboratory needed for xenon arc exposure testing of polyester film and polyester chip & film . The xenon arc exposure test of our UV polyester film for 1000hr.
Middle East Materials Laboratory needed for Gel Permeation Chromatography for HDPE Material GPC Testing
Materials Laboratory needed for Synthesis of candidate catalysts and verification of activity in lab validation tests. Able to handle lpg olefin monomers. Calcination at 250-700 deg C. Catalyst activation with Lewis acids. Conduct small scale batch pplymerization reaction to verify catalyst suitability. Analyze by GC but more preferably by C13 NMR.
Materials Laboratory needed for ASTM outgassing testing to ASTM E595, ASTM E595 - 15 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
Midwest USA laboratory needed for halogen lamp degradation study of plastic joining technology for measuring the infrared output of a halogen bulb used in a joining technology for Infrared radiation to melt a plastic boss, which is then formed by a metal punch, joining two plastic parts together. Our intent is to learn more about the degradation of a halogen lamp and how that degradation affects the Infrared wavelength. Ultimately we would like t ...
FDA Plastics and Polymer Laboratory needed for ASTM Testing of Polypropylene (FDA-CFR-177.1520) Test: Density (ASTM method D1505?68); Melting point (ASTM method D2117?82); Hexane Extractables; Xylene Extractables Material: Polyethersulfone (FDA-CFR-177.2440) Test: water, 50% alcohol, 3% acetic acid, N-heptane extractables Material: Polytetrafluoroethylene, perfluoroalkoxy (FDA-CFR-177.1550) Test: water, 50% alcohol, N-heptane, ethyl ...
Plastics Laboratory needed for Polyurethane Testing of Polyurethane foam Polyurethane elastomer and Polyurethane Thermoplastic
Europe or USA Materials Laboratory needed for research study for Removing Unwanted VOC's through vacuum stripping. Testing vacuum stripping under different conditions to optimise removal of VOC's in a recycled polymer compound
UAE plastics laboratory needed for Gel Permeation Chromatography testing for HDPE manholes used in sewerage network project. Material is PE100
India materials laboratory needed for test the parameters of HDPE,POLYPROPYLENE and ABS samples as follows 1.density 2.Melt flow index 3.Grade name(purity) 4.Tensile Elongation and flexural test 5.Melting point 6.Yield stress 7.Elastic modules kindly send the quotation as early as possible.
Materials laboratory needed for polyurethane foam testing
Materials Laboratory needed for ASTM Testing: Accoustic Impedance ASTM E1050
Startup developing new polymer material for fibers and textile needs complete UV degradation tests wfor different polymers (before extrusion process, not a fiber/fabric). Can you send me a quote for 3 samples testing.
Midwest materials laboratory needed for ASTM testing of multiple reinforced adhesive tape samples for tensile testing
Manufacture of rubber parts and seals for industrial applications needs materials laboratory for certificaiton testing of seals
Medical Device Materials Laboratory needed for ASTM biodegration testing to support biodegradable claim for a patient belonging bag. We're hoping to get the test done per a standard; we've identified ASTM D5511 (Anaerobic Biodegradation of Plastics) or ASTM D6954 (Oxo-Biodegradable Plastics).
Large Consumer Products Company needs polymer physical chemistry laboratory for Pore size distribution and porosity Pore characterization of hollow fiber polymer membranes
Large plastics company needs polymer laboratory for polypropylene testing: measure MFR of polypropylene but of very high MFR (~ 1200 g/10'). Measument of such a high MFR requires smaller sized die opening.
USA Materials Laboratory needed for complete analysis of a sample of an antifoam based on these specific tests FLASH POINT °C ASTM D-93 POLIAROMATIC AND AROMATIC SOLVENTS CONTENT % Weight ASTM D-6730 PH ASTM E- 70 VISCOSITY Cp ASTM D-445 ORGANIC CHLORIDES CONTENT % ASTM D-4929 IR INTERPRETATION-CHEMICAL GROUP ASTM E-1252
Large electronics company needs United States, Japan or Europe Physical Laboratory for ASTM D2628 neoprene testing: Physical Test for Polychloroprene(Neoprene) Elastic Joint Seal Following ASTM D2628 - Tensile Strength - Elongation - Hardness - Oven Aging - Oil Swell - Ozone Resistance - Low Temperature Stiffening - Low/High Temperature Recovery
USA ISO 9001 certified materials laboratory needed for ASTM Lubricant or Plastics Testing: thermal conductivity testing on lubricants, ASTM D2717 or ASTM D5930
Plastics Laboratory needed for plastics materials process chemistry research study to perfect a reliable, fast and economical method for creating a thermoset plastic-type compound from rosin and the oil of the flax seed plant. Probable involvement in ASTM testing, NFPA, ISO.
Plastics Laboratory needed for residual Low-density polyethylene LDPE testing of LDPE in Vitamin E TPGS? Our raw material (Vitamin E ) is packaged by LDPE bag.
Middle East materials laboratory needed for ASTM Testing: barcol hardness test glass reinforced plastic to ASTM D 2583, Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impresso
Bioanalytical Laboratory needed for Biological sample characterization testing
United States materials laboratory needed for ASTM Testing of foam to ASTM D3575-BD, Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers compression/deflection, and compression set.
Plastics Laboratory needed for ASTM Testing of plastic samples tested for scratch resistance, crack resistance and wear resistance of ASTM D7207-13, D5628, E11-15
Middle East, Asia or Europe Materials Laboratory needed for Plastics Testing: ASTM Testing to ASTM D746, Brittleness Temperature of Plastics
Materials Laboratory needed for foam testing
Asia polymer laboratory needed for HDPE Testing: Test 3D filaments made of recycled HDPE flakes
Plastic manufacturing factory needs Saudi Arabia materials laboratory for plastic analysis.
Midwest USA physical chemistry laboratory needed for materials Testing to measure specific gravity of dry soy flour / powder
URGENT: Large Hydrocarbon company needs Physical Laboratory for ASTM C518 and ASTM C177 testing on Polyurethane foams. Also require thermal conductivity testing at -165degC for the same. Urgent requirement.
Polymer Laboratory needed for Polymer Identification. A polymer sample in form of a circular disc needs to be identified by ATR/FTIR/RAMAN
UNIVERSITY RESEARCHER NEEDS LABORATORY FOR POLYMER HYDROGEL STUDY TO ANALYSE BIOCOMPATABILITY TEST AND CYTOTOXICITY TEST
Polymer Laboratory needed for third-party testing of polymers
Materials laboratory needed for ASTM or ISO Testing for for plastic technology softening point for toner resin, using capillary rheometer
Plastics Laboratory needed for plastics testing.Test contents in plastic parts. Ethylaminobenzoate Heptaoxacyclopentatriacontane Hexaoxacyclotriacontane Tetraoxacycloeicosane Pentaoxacyclopentacosane N, O cmpd MW=>193 For a pre-test purpose of NSF61 re-submission
USA Certified A2LA ISO 17025 laboratory needed for Gravimetric Particle Analysis to ISO 16232-7 Plastic Injection Molded Back-up Sensors 2 Part Numbers 16 pieces part number Parts are plastic with metal inserts Part dimensions are approximately 2" X 1".
Europe Plastics laboratory needed for polymer testing of transparent Polycarbonate Sheets to UNI 13468-2 which thickness are around 100 micron.
Polymer Laboratory needed for PSTC or IEC Testing toPSTC-56 or IEC 60454-2: A resistance to penetration at elevated temperature test carried out on up to 10 different polymer film. A ball of 1.5mm diameter is pressed into the surface under a 10N load. Temperaure when the ball penetrates throught the film is recorded
East Coast USA polymer laboratory needed for PMMA Testing: 6 samples of PMMA that we need the following tests performed on: DSC - under Nitrogen -10 deg. C to 350 deg. C TGA - 40 - 500 degrees C
USA laboratory needed to distill a per fluorinated poly ether for us. Initial volume 1 gallon, with follow on work. CAS 69991-67-9 We have done this the past, but our company no longer as the capabilities. Complete work instructions can be provided.
Electrical laboratory needed for materials testing: Dielectric Constant according to ASTM D150, - DC Resistance & Conductance according to ASTM D257 - Electrical Resistance according to ASTM D257 OR D991.
Plastics Materials Laboratory needed for material tests for ash ,viscosity and melt flow in plastics most tests will be virgin material and a variety of plastic
Microscopy Laboratory needed for scanning electron microscope SEM images taken of a 2 denier Acrylic fiber to look for evidence of fiber finish on the surface or in cracks in the fiber surface. Please specify costs.
Saudi Arabia Materials Laboratory needed for Plastic film testing of EVA sheet.All laboratory test required in plastic film industry as will as reporting and SOP development, high skill in PC software word excel..etc
East Coast Polymer laboratory needed for ASTM Testing for Polymer Testing: Physical Properties of Poly-nitrated Oxetane such as density, viscosity, average molecular weight, molecular structure if possible, flammability, or other data needed to flesh out an MSDS safety sheet.
Europe polymer laboratory needed for ANSI Testing of polyurethane slab stock foams for Volume resistivity&Surface resistivity according ANSI/ESD S 20.20 ANSI/ESD S 541 We need test protocol with international validity. The lab must be Accreditation. Thank you in advance. With our best regards. Simeon
Materials laboratory needed to test UPVC fittings for ISO 1452-2 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure
India materials laboratory needed fr ASTM Testing. Test our Rigid Polyurethane Foam for the Thermal Conductivity as per ASTM- C - 177 or IS:3346, Method of the determination of thermal conductivity of thermal insulation materials
Asia polymer laboratory needed for reverse engineering of polymer material for material identification and reproduction
Polymer Laboratory needed ASTM plastics testing: ASTM D7573 (Total Organic Content) We have Plastic Tubing that requires the following test: ASTM D7573 ? Total Carbon & Organic Carbon in water by High Temperature Catalytic Combustion & infrared Detection Deionized water or ASTM Type II Water Hose Leachable material preparation: A 12 inch min section of tubing should be filled with deionized water or ASTM Type II water, then sealed & ...
USA Materials laboratory needed for plastics testing: RoHS quote on plastic components. 3 assemblies Tests seeking: 1.Lead (Pb) 2.Mercury (Hg) 3.Cadmium (Cd) 4.Hexavalent chromium (Cr6+) 5.Polybrominated biphenyls (PBB) 6.Polybrominated diphenyl ether (PBDE) A. assembly has 4 plastic components B. assembly has 2 plastic components, and 1 brass component C. assembly has 4 plastic components
Industrial Hygiene laboratory needed of ASTM elemental trace analysis of the indoor air in our manufacturing building using ICP-MS or GC-MS. Mainly we're most concerned about sulfur. There will be 7-8 samples.
Polymer Laboratory needed for Permeability test of PET (Plastic 120 ml size) bottles.
Asia Laboratory needed for Desert Climate (Natural weathering test) follow standard ISO 877 method A,Plastics - Methods of exposure to solar radiation for 2 years and evaluate every 1 years
USA polymer laboratory needed for rubber testing: Max load test on rubber deflector 5 piece test on what is the max load these rubber components can withstand.
Russia Mechanical Laboratory needed for ASTM Testing: Tensile strength for fiber-reinforced polymer bars to possibility using this product in construction Engineering. Number of samples -5.
New Jersey Laboratory needed for Microstructure steel / Tungsten testing including: Mount parts. polish, etch and picture the micro structure.
Asia / India Materials Laboratory needed for ASTM Testing: Thermal aging of rubber in n propane pressurized container ASTm D 471
United States polymer laboratory needed for REACH compliance testing: project that has been approved that will use our reprocessed Copolymer Polypropylene black pellets. In order to move forward with this project, our customer is requiring us to provide them with a REACH compliance letter along with test data. I am in search of a company that will be able to provide this information for us.
USA Materials Laboratory needed for ASTM polycarbonate testing to ASTM G153 test cycle 1 environmental weathering testing: 15 flat samples (2x2 inch) 15 curved samples (2x2 inch) All samples are directional requesting 500hr and/or 1000hr evaluation visual for color change, hazing, optics
North Carolina laboratory needed for OECD biodegradability testing to determine OECD 302 biodegradability understand the biodegradability of our biopolymer that is made with a starch and hemicellulosic backbone.
USA electrical laboratory needed for ASTM Testing: Dialectric constant of polymer film
East Coast USA Mechanical Laboratory needed for polyurethane testing with ~ 400% elongation. The testing requires an extensometer attachment to a tensile tester. each test will consume three samples. we will need between 10 to 20 test performed over a 1 month period.
Middle East Polymer laboratory needed for UN certification testing for polypropylene Woven Jumbo bags (FIBC) ,
India analytical chemistry laboratory needed for Glycol testing. The following test results are required. 1. Name of the Glycol used. 2. Concentration of the Glycol with water 3. Viscosity of the glycol.
Manufacturer of polymer film used in the food packaging industry needs ISO FDA GMP and NABL Packaging Laboratory for ASTM and ISO heat seal coating testing of heat seal product which is used in packaging of wet and dry product like pickles, Jams, Ketchup?s etc. We would like to carry out the test which shows is the chemicals present in the liquid products can react with the coating done on film or not. Please send quotation to perform . ...
USA packaging laboratory needed for polymer testing: determine index of refraction of 2-8 micron polymer on 100 micron substrate by prism coupling methods
USA Materials Laboratory needed for ASME Testing of Water vapour permeability according to ASME-E96, product Polypropilene NonWoven laminated with Polyethilene Breathable film
Europe or Middle East Laboratory needed for materials testing : Coating testing to EN10290 for Qualification of polymer pipe coatings
Resin manufacturer needs packaging materials laboratory for polymer testing of the film laminate with other substrates like PE, etc to make a test sample of laminate film used in packaging industries..
University Researcher needs India polymer laboratory for polymer research TGA,2- DSC.
Polymer Laboratory needed for NORSOK Testing: NORSOK M-710,Qualification of non-metallic sealing materials and manufactures. what is the price for one material?
University Researcher needs Materials Laboratory for polymer composite testing including microtome into cross-sections of interface of composite with epoxy and fiber and AFM testing.
Plastics Laboratory needed for peel strength test machine according to BS EN 13121-3;2008 and other relevant standard to check the peel strength of thermoplastic lined frp laminate.
Spain Materials Laboratory needed for ASTM Testing to ASTM D471 and ASTM D413: Materials, mechanical (Polyurethane Layflat Hose for fuel transfer) MIL-PRF-370J 126.96.36.199.3 Adhesion after fill test (type C hose only). A 12-in. section of hose shall be stoppered and filled with reference fuel B as specified in ASTM D471. The section of hose with the test fluid shall be maintained at a temperature of 160 ± 2°F for not less than 46 hours. At the ...
Malaysia or United States materials laboratory needs polymer laboratory for epoxy testing of one customized epoxy to evaluate the dielectric value for this part. I suspect the dielectric constant will be approximately 10+/-10% at 50 kHz. For samples, I will send to your company for testing. Samples size will be less than 5 pieces.
Materials Laboratory needed for plastics ASTM Testing to ASTM D785-08 Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
Plastics Laboratory needed for polymer composite testing to determine diffusion coefficient in compostes and polymers.
Pultrusion company looking for Europe plastics laboratory for ISO mechanical, electrical and heat testing s for pultruded FRP profiles. Would help, if most of the test could be done at the same test lab.
United States Materials Laboratory needed for DIN Testing to DBL 5555, DaimlerChrysler AG 70546 Stuttgart Standards Car Interior Materials Testing and DIN 53435, Testing of plastics; bending test and impact test on dynstat test pieces. standard by Deutsches Institut Fur Normung E.V JCS-3709
Analytical Chemistry Laboratory needed for water testing for Acrylamide and Polyacrylamide.
India polymer laboratory needed for ASTM Testing and BIS Testing: Epoxy Testing of more than 200+ samples to be tested of epoxy components. having resins and hardners.
Polymer Laboratory needed for PET resin sysnthesis and characterization testing to synthesize, characterize and synthesize PET resin. We have ethylene glycol (EG), and we would like to compare PET synthesized from our EG with conventional PET"
Plastics Laboratory needed for cryogenic testing: cryogenic tests for Thermoplastic multilayer (non-vulcanized)hoses and hose assemblies according to BS EN 13766:2010?Temperature -50 degrees centigrade If you need further details please ask Thank you very much
India polymer laboratory needed for polymer testing: Thermal Conductivity Testing for 'K' value Polyurethene Foam (PUF)
Canada Plastics Laboratory needed for ISO Testing: Heat deflection temperature for 2 injected plastic bars for each materials to ISO 75 Heat Deflection Temperature
Texas plastics laboratory needed for DIN Testing performed on plastic sheeting to DIN 53370 DIN 53378 DIN 5388 DIN 53455
USA MicrobioogyMaterials Certification Laboratory needed for ASTM Certification Testing to ASTM D6413, Antibacterial Analysis. Type of Product: cetinete of tissue (90.4% Polyamide, 9.6% Spandex).
India Polymer Laboratory needed for polycarbonate analysis of powder.
Polymer Laboratory needed for ASTM Testing: Polymer Testing for Minimum Film Forming Temperature one sample of all acrylic polymer emulsion materials
Plastics Laboratory needed for plastics comparison testing: Compare two different plastics to a burned plastic to indicate which plastic in contained in the burned materials.
Polymer Laboratory needed for polymer testing. Test polymers for iodine number for unsaturation? Please specify what will be the cost for each sample?
Plastics laboratory needed for textile fiber testing. Form plastic pellets into textile fibers for testing/analysis and carry out testing on those fibers.
Materials laboratory needed for ASTM Testing. Plastics Testing to ASTM D256-06 Determining the Izod Pendulum Impact Resistance of Plastics
Plastics materials needed for analytical chemistry testing: deformulation of 1 part hybrid epoxy. Can you tell me the cost ?
US testing laboratories for OECD Biodegradation Testing - specifically Biodegradation of Plastics Testing and other ingredients used in personal care. Looking for labs that currently run OECD 301 and OECD 306. Please advise how long till I am able to receive a response. Thank you!
computer Manufacturer needs Plastics Resin Testing of computer keyboard's one plastic part: it is manufactured from ABS resin, but we need proofing that it does not has included Polyvinyl Cloride (PVC)?
Polymer Laboratory needed for polymer testing studies and failure analysis study: ECE (R-110 and R-67) requirement testing on several polymers and plastics used in parts we produce. The following tests include: -Compressed natural gas (CNG)/Liquefied petroleum gas (LPG) compatibility, which involves exposing a sample of a given material to pentane at a certain temperature and pressure for a period of time, observing the volume and mass change. -R ...
Africa plastics laboratory needed for polymer testing of 10 samples of organic powder (prepared from poly (ethylene terephthalate). For these samples, the following tests are required: 1. GPC 2. NMR 3. FTIR I need to know the compounds present in the samples
Materials laboratory needed for polymer testing 1- Tests for colour fastness of surface, according to DIN EN 20105-A02 2- Emission Behavior, according standard VW501 80. 2.1- Fogging PV3015 2.2- Emission of organic compounds according to PV 3341 2.3- Odor test according to PV 3900 3- Lightfastness: Green glazing; 5 periods of exposure according to PV1303.
Plastics Laboratory needed for ASTM Nylon 66 material analysis testing and product in cold chamber at -20C. Faced nylon 66 molded product breakage problem. Used Nylon 66 molding product material analysis testing and product in cold chamber at -20C.
South California Materials Laboratory needed for plastics testing: intrinsic viscosity test needed on plastic resin water bottle gradeIV test on 3 sample of plastic resin in pallet form.
Plastics Laboratory needed for polypropylene testing of 6 samples of PP and I would like them tested for the following characteristics:- 1. MFI (/10 min) 2. Density g/cm3 3. Tensile strength MPa 4. Tensile elongation MPa 5. Fexural modulus Mpa Please confirm the cost of doing these tests for the 6 samples, and please state how long it takes.
Plastics laboratory needed for validation testing for XLHDPE and LLDPE material used in the manufacture of DEF tanks for Navistar. As described; 1. Soak 10 tensile bars of the LLDPE material (and XLPE material for a baseline) in room temperature DEF solution for 1000 hours (6 weeks), measure the stress strain curves of 10 samples not soaked as well as the 10 soaked samples and compare loss of strength and modulus. Compare the two grades of materi ...
Mechanical Laboratory needed for mechanical Standard testing for a plastic pallet/skid, including static and dynamic load
Polymer Laboratory needed for plastics Testing of PVC product Identification Testing of PVC
Canada Polymer Laboratory needed for polymer verification for the NCO and OH levels verified in polymers
URGENT: Europe physical materials laboratory needs quotation for the following physical analysis (in accord to PSA B67-7050 specification, look the attachment) done ON THE UV AGING FOAM (after 100 hours of UV Aging). Density D45 1045 Resilience D45 5128 Indentation Hardness (P25/5, P50/5, P65/5) D41 1003 Elongation at break D41 1050 Friction Resistance D451010 It's very important for us to be rapid. Please send us the quotation for accel ...
Europe Plastics Laboratory needed for plastics testing
Materials Lab needed for testing according DIN 30643 (Resistance to wiping and wear of lettering)on a material for identification, a polyester nameplate
University Researcher needs Asia Materials Laboratory for LDPE materials evaluation: TGA analysis on samples of :pure LDPE, solutions formed from solvation of LDPE in benzene (gel-like compounds)
India NABL Accredited Analytical Chemistry Laboratory needed for PET Testing: AA and IV test reports for PET preforms (10 SKUs). Please mail your offer with details."
India mechanical laboratory needed for DIN Testing. Mechanical load testing of mechanical wheel to din 76051 or if any compatible mechanical load test method wheel clocks load testing as per din 76051
India analytical chemistry laboratory needed for distillate testing of distillate made as output(fuel) from plastic. address: Mahatma Gandhi University College of Engineering, Thodupuzha, Idukki, Kerala, India.
Africa materials laboratory needed for plastics testing : plastic migration kinetics with computational and analysis
USA Microbiology Laboratory needed for ASTM biodegradability testing of prototype soy-based polymeric surfactant to assess biodegradability in anaerobic conditions. It will come in form of aqueous solution of dry (whichever will suit your facility)
Asia materials laboratory needed for polymer testing to test the polymer tube samples to analyze the composition of the material and any additives.
Materials Laboratory needed for California Proposition 65 materials testing
Materials Laboratory REACH testing of PSA masking films.
Plastics Laboratory needed for physical testing: UV and moisture resistance testing on Black HDPE pails as well as 4 mil polyethylene bags.
India Plastics Laboratory needed for plastics testing of Laminated plastic Films
Polymer Laboratory needed for UV and moisture resistance testing on Black HDPE pails as well as 4 mil polyethylene bags.
India Plastics Materials Laboratory needed for plastics testing: 1 DOP (DI OCTYL PHTHALATE ) AS PER ATTACHED ANALYSIS REPORT - SPECIFIC GRAVATY - DENSITY - FLASH POINT - EVOPRATION POINT - FREEZING POINT SO CAN YOU PLEASE HELP IN THIS CASE ? AND ALSO DO YOU HAVE TEST FACILITY FOR LIQUID STABILIZER , TIO2 , PVC RESIN , LUBRICANT GMS , LUBRICANT 316a, AND CALCIUM UNCOATED ???? JAY PATEL H.O.: 12,4th Floor, Kalapurnam,Near ...
Europe or USA Materials Laboratory needed for polymer testing: comparative testing of radiopacity ASTM F640Comparative radiopacity to ASTM F640 testing of filled polymers. Specimens consist of injection molded Plastic plates approx 50mm x 80 mm with different wall sections. Possibly tube samples. 5 different materials. No special handling requirements. Samples could be cut.
Canada or USA Polymer Laboratory needed for plastics testing: PET testing for 1. Measuring melt flow index of PET samples 2. Molecular weight evaluation of PET samples using size exclusion chromatography 3. Thermo gravimetric analysis (TGA) on PET samples with analysis of the gaseous products
Accredited Plastics Laboratory needed for PET Testing for intrinsic viscosity of the preform PET. Please let me know whether the method of study is accredited; it is essential eventual report would come from an accredited laboratory. We would like to examine 7 samples taken from 5 preforms and two ready bottles.
Polymer Laboratory needed for ASTM Testing. Polyethylene plastic testing for water vapour permeability of polyethylene plastic sheets , directional reflectance and luminous Transmittance ASTM E96, ASTM E1347, ASTM D 2103
India Polymer Laboratory needed fro uPVC Testing: Certification Testing for uPVC certificates (Pipe 160mm dia, class 5) for advanced vision company-airport project
Polymer laboratory needed for ASTM Testing: Polymer testing of the Liquid Oxygen Compatibilty in a polymer (PTFE)to ASTM D2512 (LOX Mechanical Impact Test)ASTM D4809 (Heat Combustionb TEST) .
Physical Laboratory needed for NORSOK Testing: Physical testing for elastomeric materials Ageing (sour fluid exposures) to NORSOK M-710, Qualification of non-metallic sealing materials and manufacturers RGD resistance
Polymer Laboratory needed for polymer testing: Chromatography Testing to determine the Molecular weight Distribution of PET polymer, 2 samples,
Middle East Manufacturer needs polymer laboratory for ASTM Testing: PVC Tests for mechanical and chemical testing on material of uPVC pipe,according to ASTM D 1785-D 1784 and related fabrication standards. Pipe is class 5 , schedule 80 ,Pipe diameter size is 150mm ,6 inches and (40cm length). Please provide to us the required tests and your quotation asap.
Manufacturer of PVC Conduits Pipes and fittings , needs approved laboratory for materials testing: British Standard tests in the British Standard BS 6099 Part1 , BS 6099 Part 2, section 2.2, BS 4607-1 and BS 4607-5 which incluled following: 1- Dimensions and Visual Inspection 2- Bending Test 3- Compression Test 4- Impact Test 5- Collapse Test 6- Resistannce to Heat 7- Resistance to Burning 8- Electrical Insulating Strength 9- Insulation Resistanc ...
Polymer Laboratory needed for polypropylene testing of polypropylene resin two times per year for test results on melt flow and yellow index. We are looking to verify the test results given to us by our suppliers on their certifications.
Independent, accredited Plastics Laboratory needed for plastics testing: failure analysis of sealant material for failure on site that might be structural silicone, weathering silicone or polyurethane. We are looking for the following: Confirmation of the material itself. Any analysis of deterioration if it can be compared to a fresh sample.
UK Laboratory needed. Polymer Laboratory needed for Specific Melt Resistivity Testing of polyester film chips to define its conductivity level."
Accredited Polymer laboratory needed for plastic testing of plastic pellets. Gas chromatography testing on a number of extruded tubes and resin granules. The granules/ tubing are essentially PVC with a number of plasticizers to increase their flexibility for content of DEHP, DEHA and DEHT in the tubing and or granules provided. Please advise regarding turnaround times, costs, limits of detection, sample requirements etc.
Materials Laboratory needed for rubber testing large quantity of samples of rubber available. We simply need to find out the composition of the rubber we are working with (i.e. is it EPDM, Acm, ect.) We can ship all samples
Polymer Laboratory needed for ASTM Testing: Electrical conductivity testing of some polymer composites to be tested to ASTM D 257 (Electrical conductivity or surface resisitivity of polymer composites) the range is 10-2 to 10-17 S/cm the range is 10-2 to 10-17 S/cm
US Plastics Laboratory needed for plastic ASTM Testing. A full package of information for HDPE material including: 1.Stress-Strain data for (tensile, compression, shear) 2.Strain rate sensitivity parameters identification 3.The graph of strains in lateral and longitudinal directions
Plastics Laboratory needed for carbon black testing for amount of carbon black in rubber hose.
Plastics Laboratory needed for ASTM Testing : Polypropylene resin testing to ASTM D1238,Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer , melt flow rate, melt index, volume flow rate ASTM D6290, Standard Test Method for Color Determination of Plastic Pellets. from lots to compare to supplier information Polypropylene resin, 1 lb. samples to verify melt flow and color (YI)
Materials Laboratory needed for ISO Testing to ISO 354, DETERMINATION OF SOUND ABSORPTION to carried out acoustic test for a material made of recycled PET. Thickness is 9mm and sheet size is 4' x 8'
Plastics Laboratory needed for plastics testing of test Microwave use plastics laminated bags that under 21 CFR 177.1390 (Laminate structures for use at temperatures of 250 deg . F and above) Our microwave steam bag is made of Polyester (outside layer) and Cast Polypropylene (inside layer- food contact) laminated with Polyurethane adhesive.
Petrochemical firm needs middle east plastics materials laboratory for ASTM Testing 2 samples of PET polymer granules to ASTM D5511-02 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditionsor equivalent
USA Polymer Laboratory needed for injection molding of six different polymers injection molded to ASTM D 543, Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents , chemical reagent, dimensional changes, exposure, mechanical property(referencing ASTM D 543, 188.8.131.52 for weight and dimension change). The standard specimens are supposed to be disks that are 2 inches in diameter, 0.125 in thick with a total surface area o ...
Materials Laboratory needed for Toxicology Testing, ASTM Testing, Biodegradability Testing: oxo-biodegradation tests on plastic bags to ASTM-D6954 standard. These bags have been manufactured using an additive. 1. Chemical composition 2. Abiotic degradability 3. Biodegradability in soil 4. Eco-toxicity
West or Northwest USA materials laboratory needed for polymer testing by SIMS or Raman. Need to analyze some defects in a polymer film. Our analysis hasn't been able to isolate any obvious contaminates. Our results just return sample matrix material. I was thinking SIMS or Raman to determine whether material within the defect area is in fact part of the original matrix or is foreign.
Polymer Laboratory needed for polymer testing of composite filling (polymer)by 3D profilometer and vicker microhardness tester.
Materials Laboratory needed for FEDERAL MOTOR VEHICLE SAFETY STANDARDS AND REGULATIONS FMV Flammability Testing to FMVVSS302,
FDA GMP US analytical chemistry laboratory needed for plastics Extraction testing outlined by FDA 21CFR177.1520 and 21CFR176.170 for molded parts based on polypropylene.
US Polymer Laboratory needed for molecular weight testing by X-ray Photoelectron Spectroscopy (ESCA) Trying to assess approx molecular weight for roughly 3 organic polymer (singly-charged) high mol weight populations on surface of material.
US polymer laboratory needed for Polymer Testing: Small Angle Xray Diffraction. Trying to assess approx MW (very high) for 3 different organic polymer populations on surface of material.
US polymer laboratory needed for spectroscopy testing: tip enhanced raman spectroscopy TERStwo (2) samples to compare; trying to assess approx high mol weights of 3 different organic polymer populations on surface of material
Polymer Laboratory needed for polymer testing of PE film with trace amount of additive. Could you identify the additive?Any spectroscopy or thermal analysis may be working?
Materials Laboratory needed for DIN Testing of Rubber Closed Cell Elastomeric Thermal Insulation in Tube and Sheet Form to DIN 4102-1, DIN 1988/7, DIN 4109, Closed Cell Content Test, etc.
Plastics laboratory needed for forensic analytical chemistry testing: UV Inhibitor testing for amount levels based on 2 baseline samples. Material is polyethylene netting.
US Materials Laboratory needed for ASTM Testing to ASTM D648: Need Heat Deflection Testing of 1/8' to 1/4' diameter foam rod
Materials Laboratory needed for plastics testing: identification of few ppm of additive in poly(ethylene) film from none additive PE film? I tried the subtraction of spectra, but failed to identify the material because too small amount of additive.
Plastics Laboratory needed for SAE polymer testing of Fluoro polymer to SAE AMS 2491 Rev E.Surface Treatment of Polytetrafluoroethylene (PTFE), Preparation for Bonding
Plastics manufacturer needs environmental toxicology laboratory for plastics toxicology testing of manufacturer's UPVC Pipes (certification testing) which are used in a variety of ground applications.
Manufacturer of Fiber reinforced plastic products like tanks, vessels, scrubbers etc. needs plastics laboratory for ASTM Testing: the coupon testing in mumbai as per our specified astm standards as mention below 1) Flexural Strength & Flexural modules- ASTM D 790 2) Tensile Modules - ASTM D 5063 3) Peel test & Lap shear test for dual laminate - BS 4994
ISO Middle East plastics laboratory needed for polymer testing: thermal conductivity of polymer coating 1-4 mm thickness.
Oregon plastics laboratory needed for polymer testing: crosslinking of acrylaminde polymer sheet.
India or UAE materials laboratory needed for ASTM Testing (Thermal Conductivity Testing ) for Thermal Insulation foam samples to ASTM C518: 3 No.Measuring range 0.001 to 0.1 W/m.k
Materials Laboratory needed for ASTM Testing: Thermal Conductivity Test as per ASTM C518 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus. Insulation Material is : 25MM thick, foam density of 25 kg/m3, Closed Cell, Cross linked Polyolefin Foam with factory fused pure reinforced Aluminum Foil and acrylic double sided adhesive. My test parameters are at mean temperature of 23 deg ...
Plastics Laboratory needed for ASTM Testing: Darmstadt Pipe Tilting Jig Test)on pipe pvc pipe liners:DIN 19565 200,000 cycles. High Pressure Cleaning Resistance: DIN 19523 Thermal Movement:EN 1055 Heat Deflection Temperature (ASTM D648 Method A Izod Impact Value (ASTM D256 Method A)
Materials Laboratory needed for thermal testing: Thermal conductivity tests
Plastics Laboratory needed for plastics testing: Basic plastics tensile testing of plastic chain lengths approximately 1 metre long. Anticipated tensile less that 8000lbs. Multiple samples to establish Average Ultimate Strength. no special handling required.
USA GLP Toxicology Laboratory needed for GLP OECD Toxicology Testing. Biopolymer Testing. 1 sample (more to follow) of a bio-polymer (DfE criteria set as chelant) to be tested for data used in an independent review for CleanGredients. Test must be inhalation (not oral). Please provide quote for: OECD 422, 421, and 412.
Saudi Arabia, UAE, India, Middle East, GCC Plastics analytical chemistry laboratory needed Analytical Chemistry Laboratories for carbon black testing of recycled tyres and to analyze the chemical characteristics/specifications/ Contents of the recycled tire derived products such as Pyrolytic Oil and Pyrolytic Carbon Black. Product samples shall be sent to the qualified laboratory upon receipt of acceptable price quote.
ILAC certified Asia mechanical laboratory needed for Mechanical testing as per : as per MS2086(BS EN1746, or BS3212 requirement)is accreditated.
Canada materials laboratory needed for physical Testing of lighting for physical and optical properties: Hardness, specific gravity, tensile strength, tensile elongation, flexural modulus, melt index, impact strengthOptical: transmission loss, refractive index, numerical aperture
Asia Plastics Laboratory needed for Plastics Testing to BS EN1746: EMSD gas authority not allow due to MS2086 which is equivalent to BS EN1746 is not listed in accreditation list although we product certification license.
NABL India Laboratory needed for raw material and coating pipe testing of fusion bond for accreditation purpose . fusion bond epoxy, polyethylene,polypropylene
India Materials Laboratory needed for ASTM Standard Testing for Physical properties of Flurosilicone and silicone. Properties are Heat aging, low temperature brittleness, Fuel test.
India Plastics Laboratory needed for glass testing: fiber orientation of the injected molded component of material N66 composed of 65% polyamdie ,35%Glass fill.
Canada or USA Plastics Materials Laboratory needed for Ford / SAE J2302 thermal effectiveness testing. BMW/SAE 2302 thermal effectiveness testing. Need testing on wire harness tapes.
India Accredited Environmental Laboratory needed for ISO 14855 for bio-degradation testing to ISO 14855, Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions -- Method by analysis of evolved carbon dioxide -- Part 1: General method
Plastics Laboratory needed for ASTM Testing of Polyethylene lined material to establish various measures. 1. Physical tests? a. Hardness test (ASTM D 2240), b. Density test (ASTM D 792 or ISO 1183-1), c. Thermal expansion test (with Netzsch dilatometer), d. Erosion resistance test (at different angles and temperature), 2. Gas permeation, diffusion & solubility (PDS) test with CO2 gas at temperatures 60, 75 and 90 C, 3. Hydrocarbon uptake & PDS da ...
Israel, USA or China plastics laboratory needed for glass fiber testing: Silica Glass Fiber Cord Polyethylene terephthalate fiber Silicone covered Fiberglass tubing Nickel Chrome heating wire Various materials used for labeling Rubber plugs for sealing
ISO Accredited Africa Laboratory or Europe Laboratory needed for bio-degradability Testing of bio-degradation of plastic packaging material.
India, Karnataka, Bangalore plastics laboratory needed for plastics testing of polythene covers bags. we need to test our biodegradbale plastic polythene bag
USA Materials Laboratory needed for ASTM Testing, PTFE creep test to ASTM D2990-09
India Materials Laboratory needed for ASTM Testing: Plastics Testing profile to astm e84-70,astm e84-81A.
ISO Analytical Chemistry Laboratory needed for DIN Testing of inmolded part for 1,3 Butadiene per DIN EN13130-4, Materials and articles in contact with foodstuffs - Plastics substances subject to limitation
Southern California Plastics Laboratory needed for random third party testing: quality control testing of our production line for: tensile, impact, heat distortion, moisture, etc. for engineering resin
Asia Mechanical Laboratory needed for SAE Testing of Fuel pipe for engine, would like to be tested from SAE.
Plastics Laboratory needed for plastics testing: Size Exclusion Chromatography Service needed. Quotation on a per sample basis. Phenolic Resins, molecular range 100-10,000. Polystyrene Calibration, plotted chromatograms, calculated molecular weight and number average for resins.
Texas certified physical laboratory needed for MIL-STD airline seat testing. The specifications are: MIL-S-23190 50 pounds per AS23190-1 sh 5 (note 6) Would like to know what labs are in the area for various testing including material properties testing for aluminum, steel, and plastics.
USA Plastics Laboratory needed for polyester testing : Test Polyester Sewing Thread Test Thread per Fed STd-191 Method 4804&5804.
USA Plastics Laboratory needed for Fiber reinforced Plastic coupon testing 1) Glass content, wt percentage. 2) tensile strength, 3) flexural strength, 4) tensile modules, 5) flexural modules 6) peel test & lap shear test for Pvc Frp coupon.
India Plastics Laboratory needed for Testing as per IS 12866:1989 for light diffusion of Fibreglass Reinforced Polymer Roofing Sheet
Europe or UK plastics laboratory needed for PVC testing in PVC materials for medical device. Determination of: 1.Jellification degree2.K-Value3.Shore A hardness
Toronto Plastics Laboratory needed for plastics Testing of sample pieces of HDPE and LLDPE plastics to ASTM E1354 at an incident heat flux of 50KW/M^2 in the horozintal Orientation.
Government needs North Carolina laboratory for raw material testing nylon testing.
India Toxicology Laboratory needed for toxicity testing of latex from Wrightia tinctoria plant has toxic effect on humans taken in any quantity with curd
United Arab Emirates Materials Laboratory needed for ASTM Testing Mechanical, Material and Analytical Analysis of Polyethylene: Cross Linked Closed Cell Polyethylene FOAM; primarily used for Thermal Insulation. We want to perform some tests as per ASTM standards.1. Compression deflection as per ASTM D3575 D 2. Flammability as per ASTM D3575 M 3. Energy absorption as per ASTM D3575 R2 4. Buoyancy as per ASTM D3575 AA 5. Constant compression creep ...
India Plastics Laboratory needed for plastics testing: Tensile testing of cotton based fibre rainforcement plastic Breaking load,Strain & Stress at failure,%Elongation,Elastic modulus,Stress Vs Strain Plot,Load Vs Deflection Plot
South Africa plastics laboratory needed for lastics testing: Relative Viscosity on plastics Vicat
India analytical chemistry laboratory needed for oil testing of highly viscus oil
Florida materials laboratory needed for Peel and Shear testing for HDPE or XR-5 liner mateirals.
Plastics Laboratory needed for polypropylene testing: % etyhlene in PP and how much is cost per sample.
USA Plastics Laboratory needed Melt Flow Index or Melt Volume Ratio of thermoplastic urethane pellets. Looking for impartial testing for discrepancy between manufacturer and customer results.
Plastics laboratory needed for ASTM Testing of 7-8 samples of vinyl sheet piling. Tensile strength, IZOD impact, transmissivity and equivalent permeability, heat deflection, and UV stability degradation.
Middle East materials laboratory needed for teflon testing of samples of teflon rods and sheets in dubai for the exact composition of the mixture in it.
USA Materials laboratory needed for polyethylene foam testing to FMVSS Standards: CMVSS/FMVSS 302 horizontal burn rate testing on Cross-linked Polyethylene Foam.
Saudi Arabia Plastics laboratory needed for ASTM Testing: MELT FLOW INDEX OF HDPE & PP 5 SAMPLES
Europe plastics labroatory needed for DIN antistatic testing to DIN 53482 to determine the antistatic feature of artificial leather we are going to develop
Plastics Laboratory needed for ASTM Plastic Testing of injection plastic components of PBT Valox, particulary. Fusion point, Fuid point, specific weight, hatdness, tensile strenght.
Asia UKAS physical laboratory needed for ISO color fastness testing in air vent made out of ABS . as now it get yellow from white in 6 months.need test to meet uka nd eu standerd.need specification to produce and test. "
Materials Laboratory needed for Rubber Certification Testing to Density acc. to DIN EN ISO 1183-1Hardness acc. to DIN 53505 Tensile & Elongation acc. to DIN 53504 Permanent deformation acc. to PV 3307Low temperature behaviour acc. to VW 2.8.1 Electric insulation properties acc. to PV 1015Condensation atmosphere with constant humidity acc. to DIN EN ISO 6270-2I . one sample of EPDM rubber certification testing
USA materials laboratory needed for polymer testing of R&D polymer sample for screen Anti-microbi ability of polymer solution2. DSC of Melt and Tg transion temperature3.surface tension in 0.1% solution4. foam height by Ross-Miles test.
Europe Materials Laboratory needed for ISO Testing or ASTM Testing: mechanical stability for nathural and synthetic latex
Materials Laboratory needed for petrol octane buster testing on rubbers.
Materials Laboratory needed for rubber testing: Thermal Conductivity of a 13 Ply Rubberised canvas belt at your facility. If yes, please inform the charges for the same with lead time and sample size you required for the same.
Asia plastics laboratory needed for plastics testing: Oxygen Transmission Rate (OTR) for plastic film Laminate plastic film
Plastics Laboratory needed for ASTM Testing: creep analysis for a plastic material per ASTM D2990, Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics.
USA physical laboratory needed for flammability testing to UL 94 Standard for Safety of Flammability of Plastic Materials for Parts in Devices and Appliances testing. 5VA and V-0 at 2.5 mm, V-0 at 1/16"
UAE plastics laboratory needed for rubber testing: quality checking of rubber used in conveyor belts for maximum long life . for stone crushing company in uae . We would like to know if you provide services for testing of the quality of material used in conveyors depending on which we will decide whther to purchase the conveyors belts of a particular brand or a dealer . This is important to us as we spend a large amount of money on purchasing co ...
Asia and India plastics laboratory needed for Delta Y of Purified Terephtaliec Acid 2-3 samples of PTA, Required test named as delta Y .
Materials laboratory needed for ASTM Degradation Testing plastic anaerobic degradation testing based on ASTM D5210 in south-east Asia region (singapore, thailand, malaysia,
India Polymer Laboratory needed for chromatography testing : Liquid polymer composition alalysis Gel permeation chromatography
Europe Materials Laboratory needed for plastics testing: Determination of the coefficient of thermal expansion (TMA - ISO 11359; or dilatometry) -40ºC to +80ºC
Physical Laboratory needed for ASTM testing foam insulation for tensile strength to ASTM D1623, Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics at cryogenic temperatures (-265 F / -165 C). Can you do such testing? If so, can you provide me a rough budgetary cost to perform this testing in 3 directions on one type of foam insulation? The foam is polyisocyanurate with a density of 2.5 lbs/ft3 (40 kg/m3 ...
Polymer Laboratory needed for polymer testing of polymer membranes for fuel cell research, and are looking for an analytical lab to measure proton conductivity of membranes. The polymers are organic/inorganic materials.
Safety Laboratory needed for BS EN Testing to BS EN388 Protection against Mechanical Hazards and BS EN422, Rubber and plastics. Machines. Safety
Plastics Laboratory needed for polyester testing. Determination of nitrogen and /or sulfur content in the range of 0.1ppm up to approx. 10ppm Sample is a thermoplastic polyester (solid at RT)
Plastics Laboratory needed for polymer testing to determine the molecular weight and polydispersity index of an insoluble polymer (insoluble in commonly used organic and aqueous solutions)
Plastics Laboratory needed for ASTM Testing, ISO Testing and DIN Testing of 25 kg capacity Plastic bag which used for packing polypropylene or polyetheylene pellets inside the bag to be tested for its fitness
Rubber manufacturer exporting rubber products to Europe needs rubber testing of rubber mat for electrical resistance testing to: EN 13501-1/DIN 4102 B1, BS 921 and ISO 1853. Please inform us the possibility of doing this test in your laboratory and offer us your most favorable quotation for the test.
Mechanical Laboratory needed for plastics automotive testing to test painted plastic parts test for VW TL 211 Specification.
Plastics laboratory needed for epoxy testing: "LONG TERM FLEXURAL CREEP TEST" for epoxy resin CIPP liner use in pipe rehabilitation.
Plastics laboratory needed to test water vapour transmission rate and oxygen transmission rate in some flexible films. I have 16 samples to test it.
Plastics Materials Laboratory needed for polyethylene testing of 12" O.D. corrugated polyethylene wastewater drainfield pipe for 15 years and we would like it tested for H-20 wheel loads and for burial to 8 feet deep.
America Microbiology Laboratory needed for antibaterial testing of "Anti-bacteria & Anti-Fingerprint Coating Agent" for electronic devices to ISO 22196 Antimicrobial Activity of Plastics "Measurement of Antibacterial Activity on Plastics Surfaces "Anti-bacteria & Anti-Fingerprint Coating Agent" for electronic devices. (we apply to window of smart phone, camera, tablet PC, E-book and so on.) Thickness of Coating is very thin(10~20nm) and char ...
USA Plastics Laboratory needed for plastics testing. Test Acetaldehyde in Bottle grade resin for PET manufacturer. We are looking for a third party to independently test our resin.
UAE Materials Laboratory needed for ASTM Testing: Properties of Polyethylene:- Brittleness Temperature - as per ASTM D 746 Dielectric breakdown voltage as per - ASTM D 149
India Packaging Materials Laboratory needed for packaging testing: Optimized temperature and compression pressure or torque for induction heat sealing of wax coated liners with sealant layers of plastics on aluminium foil laminated with pulp or foam backing.
India Polymer Laboratory needed for reverse engineering product
India polymer laboratory needed for testing plastic materials
cold crake temperature test for PVC Compound(Solid)
Materials Laboratory needed for polymer testing of 20% talc filled PP. New color is brittle. I want to see if degradation occur and compare the microstructure. I was thinking of Molecular weight and distribution and dynamic rheometry but not sure. could you please suggest the best method for this reason?
Materials laboratory needed for ASTM Testing mechanical testing to ASTM D638 Standard Test Method for Tensile Properties of Plastics. biaxial plaanr fatigue of composite materials, mo of samples:12 (almost)
India polymer laboratory needed for polymer synthesis required for 6 new novel bio-monomers plus polymer fundamental properties testing and polymer testing their ability to be used in PU, PE and PC's. Fundamental physical properties - mol weight, crosslinking, strength
India polymer laboratory needed for polymer testing: WVTR and OTR 1 water vapor transmission rate (for polymer) Standards WVTR test for polymer standards/conditions - 1 - IS: 1060 part-2 , 1960; 90 % RH gradient and 38 degree c. 2 - ASTM F 1249 - 06; 90 % RH gradient . OTR test standards/conditions - ASTM F 1434 ; 65% RH 27 degree c. ASTM F 1927-07 ; 65% RH 27 degree c.
USA Food Laboratory needed for ANSI 51 Testing. NSF/ANSF 51 (National Sanitation Foundation - Food Equipment Materials
USA Physical Laboratory needed for ASTM Testing to ASTM-D-2183 Test Method for Flow Properties of Adhesives.ASTM-D-2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index).20700071043 Chemical Agent Test for HD, Mustard Gas or GB, Nerve Agent. (attached)ASTM-D-1171 Test Method for Rubber Deterioration-Surface Ozone Cracking Outdoors or Chamber. (Triangular Specimens).UL9 ...
Chennai Plastics Laboratory needed for PVC Testing: UV light exposure weathering testing for a PVC material
India Plastics Laboratory needed for plastics testing. 3 Samples Need to be tested
Asia Materials Laboratory needed for ASTM Testing to ASTM 6954 - Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation comprises three Tiers of testing; oxidation, biodegradation and ecotoxicity. Tier 1- The determination of molecular weight (MW) of HDPE containing ReverteT exposed to a combination of UV and elevated temperature demonstrates that ReverteT for High Density ...
India POLYMER LABORATORY NEEDED FOR BIS TESTING FOR BIS APPROVED POLYCARBONATE SHEET TESTING
Product Safety Laboratory needed for OECD Testing, OECD Marine biodegradability testing to Organisation for Economic Co-operation and Development OECD 306, Biodegradability in Seawater
Ireland Materials Science Laboratory needed for IEEE testing : Polymer Testing, Differential Scanning Calorimetry, or similar. To test for changes in Crystalininty in an amorphous polymer due to forced degradation studies
Physical Laboratory needed for ASTM Testing to ASTM C1147 Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics. Tensile testing of 95 pieces of welded cpvp and pvc.
Middle East Materials Laboratory needed for ASTM polymer testing: self ignition temperature test of polyresin material (acrylic material) according to ASTM-D1929, Standard Test Method for Determining Ignition Temperature of Plastics address: Dubai, UAE
Plastics Laboratory needed for PVC compound testing to determine the Flammability temperature ( or Temperature Index) follow to BS ISO 4589-3 Plastics-Determination of burning behaviour by oxygen index
USA Plastics Laboratory needed for MALS Polymer Testing for measuring Intrinsic Viscosity and Molecular Weight of various polymers of hyaluronic acid formulations. Preferabley using MALS or other suitable/validated methodology.
Material Laboratory needed for ASTM Testing to ASTM F1927ASTM F1249ASTM D1434Oxygen Permeability Test Water Vapour Transmission Rate Test Carbon Dioxide Permeability
USA Analytical chemistry laboratory needed for polymer testing.Need Vapor Pressure tested on two liquid polymers. Need vapor pressure curves including 50F and 350F.
Asia Materials Laboratory needed for ASTM Testing: Flammability testing to ASTM E 1354 of natural composite reinforced polymer testing
Canada and USA Analytical Chemistry Laboraory needed for plastics/ rubber testing to ISO 13741-2:1998 (Plastics/rubber - Polymer dispersions and rubber latices (natural and synthetic) - Determination of residual monomers and other organic components by capillary-column gas chromatography).we need 2 samples to be tested according to the procedure ISO 13741-2:1998. The samples are styrene/divinylbenzene copolymers and we need to now the level o ...
India Plastics Laboratory needed for plastics testing of plastic sheets address: Karachi Pakistan
Materials Laboratory needed for materials testing: Vicat Softening and Melting Point testing and would like to know price and turnaround time address:
India Plastics Laboratory needed for polymer testing: mechanical properties of polymer film (thin) % elongation and tensile testing of oplymer films, five samples of films. Please send the film size and thickness information.
Plastics Laboratory needed for DIN Testing or ASTM Testing for properties of polyisocynate NCO Content, Non-volatile content Viscosity at 23°C Iodine color value Free TDI monomer, Equivalent weight Flash point approx. 5°C Density at 20°C
US Analytical Chemistry Contract Synthesis laboratory needed for organic chemistry synthesis: Esterification of a long chain alcohol (C7 to C10) to acrylic acid. Need 1 kilogram."
India Materials Laboratory needed for ASTM Testing of Plastics Film, Base Wt gm/m2 Width mm Avg. Tensile Strenth (CN/25mm) Avg. Elongation at Break (%25mm) WVTR(g/m2*24h) Water Resistance (mbar) Other MD CD MD CD
Packaging Certification Laboratory needed for Materials Certification Testing of PVC End caps white in clour and its been UV Stabilized we need certificate for that as our client in us
Plastics Laboratory needed for Polymer Testing, ASTM Testing to ASTM D6068, Standard Test Method for Determining J-R Curves of Plastic Materials
Packaging Laboratory needed for packaging testing: UN FIBC Flexible Intermediate Bulk Container bags.
Plastics Laboratory needed for analytical chemistry testing for chemical residue left by the laundry facility after washing
Materials Laboratory needed or SAE Testing for SAE AIR4170 and MIL-DTL-83054 testing
USA A2LA Laboratory needed for GC analytical chemsitry testing of two polyurethane-nylon fabric laminates materials tested using GC to measure the following substances: 1) Methylenediphenyl diisocyanate (MDI) down to 1 ppb 2) Bisphenol A down to 1 ppm 3) Nonylphenol down to 1 ppm. The product may be used to transport beverages (milk) and the customer wants to ensure that these SOCs are not present in the polyurethane film.
Materials Laboratory needed for ASTM Testing: Saybolt color analysis by ASTM 6045 method of our Polyethylene wax sample. If it is possible at your end then please let me know the analytical charges and how much sample is required for the same.
Acoustics and Plastics Laboratory needed for JIS testing to the standards methods below of a bonded plastic sheet with a tissue layer with 2mm of total thickness. * JIS K 6850 - Adhesives - Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies * JIS K 6854-3 - Adhesives - Determination of peel strength of bonded assemblies - Part 3: Adhesives -180? peel test for flexible-to-flexible bonded assemblies (T-peel test) * JIS ...
Plastics Laboratory needed for rubber testing: lab test compressive stress relaxation of rubber. There are two test conditions. One is in 150'C air for 1008 hours, the other one is in 150'C SF 105 fluid for 1008 hours.
West Coast USA Plastics Analytical Chemistry Laboratory needed for Flakes Contamination Testing for: PVC, PETG, Polyamide. Need to know if testing can be done on recyled bottle flakes for contamination Identification purposes. Contaminants in question are PETG, polyamide, polycarbonate, labels and polystyrene. Reason for identifying this contaminant is to determine if they contribute to higher Benzene ppm on the final product.
Europe Materials Laboratory needed for ASTM testing as per ASTM D5511 : ASTM D5511 - 11 Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions
Analytical Chemistry Laboratory needed for plastics testing: comparison testing of PvC Files: DSCDSC tests on two PVC samples
Europe Toxicology Laboratory needed for Acute toxicology studies for Daphnia similis and chronic toxicology testing for Ceriodaphnis dubia in wastewater.
Plastics Laboratory needed for ASTM Testing, Melt index testing
FDA GMP Optical Laboratory needed for plastics testing to determine ABBE number on a sample, sample is a thin circular plastic material.
Europe FDA product safety laboratory needed for USDA Acceptance Testing: (United States Department of Agriculture) Reference: 21 CFR 177.1550
Materials Laboratory needed for Optical Measurement Testing. Reflectivity value of plastic material solid surface, in visible spectrum
Plastic curtains and screens manufacturer that needs Optical Laboratory for AWS testing to AWS standard F2.3 determine how much light is passing through a welding curtain. The relevant standard is AWS standard F2.3. The test will require a spectrophotometer capable of reading transmittance from 200nm to 800nm. We need 2 to 5 samples tested."
USA plastics laboratory needed for ASTM Testing to identify a plastic pellet on an extruder screen.
Hong Kong or China materials laboratory needed for Plastics Testing: ASTM Testing to test ASTM D6954-04 in accordance with ASTM D6954-04 Tier 1 thru 3.
USA Plastics laboratory needed for materials testing to EN 1598 to test 13 oz PVC material to EN1598 for blockout out properties for use as welding curtain material.
Plastics Laboratory needed for ISO or ASTM Testing: polyethylene testing for Oligomer Content in Polyethylene Terephthalate (PET) chips using either HPLC, MAE or Soxhlet extraction technique.
Electrical Laboratory needed for DIN Testing: Dielectric strength testing, Dielectric dissipation factor (tanä) testing , Volume resistivity testing, Surface resistivity testing, Dielectric constant testing
Middle East Polymer Laboratory needed for polymer testing: GPC-IR analysis on LLDPE (ethylene 1-hexene copolymers) samples to have the following results: (1) Average molecular weight, (ii) Molecular weight distribution, and (iii) Side chain branching (SCB) distribution as a function of molecular weight. We appreciate if you could let us know the analysis cost per one(1), sample, cost per five(5) samples, and cost per ten(10) samples.
Europe, Japan, Korea, India Plastics Laboratory for PET Testing: Determination of P, S,Ag in PET polyester chips powder with XRf by Lucas-Tooth calibration method.
Asia Plastics and Polymer Laboratory needed for ASTM Testing to ASTM D6954.
USA Plastics Materials Laboratory needed for plastics testing: Contact angle on a curved surface Oxygen Transmission 4 samples +/-2
Plastics Physical laboratory needed for DIN Testing of PVC membrane to DIN 53370,DIN53455,DIN53454,DIN53363,DIN16726,DIN53495,DIN50014
Plastics Laboratory needed for PVC film testing: IMDG 184.108.40.206.1.2 test on rigid pvc film
Plastics and Polymer Analytical Chemistry Laboratory needed for plastering compound testing. 1.Total Calcium content 2.Total Magnesium content 3.Loss on Ignition 4.Percentage silica 5.Polymer extraction and identification 6.Test results and its interpretation. If you could do this test please send me chargers etc.The sample i could be sent you soon.
Las Vegas Polymer Laboratory needed for quality control testing of resin pellets contents. quality control under 10 samples
Nevada Polymer Laboratory needed for resin testing on resin pellets to determine the content. we would like to use a company in Las Vegas or nearby.
US Plastics Laboratory needed for ASTM Testing: physical properties of a plastic resin tensile, elgongation, yield, flex modulus, melt index, impact - izod preferred charpy okay, hardness (shore A) SAMPLES NEED TO BE MOLDED
Polymer Laboratory needed for polymers testing: Softening point & brookfiled viscosity at 120 deg C of polymer
India Polymer Laboratory needed for PET Testing, intrinsic viscocity of pet lab testing
India Materials Laboratory needed for ASTM Polymer Testing, FTIR & TGA, of polymer for development
Plastics Laboratory needed for ASTM Testing, biodegradation testing to ASTM 5338 for 10 samples of polypropylene containing an additive which should facilitate their biodegradation.
Plastics Laboratory needed for Quality COntrol Testing, acrylic testing of acrylic used for the see-through tank wall of a new shark tank to be installed within a new world class aquarium under construction in the Salt Lake City area. The manufacturer is a Chinese firm providing their own quality control testing data. We would like to obtain indpendent testing results of some key material parameters to verify. We can provide samples of their a ...
Plastics Laboratory needed for ash testing on polyurethane foam.
USA EPA ENVIRONMENTAL TOXICOLOGY LABORATORY NEEDED FOR TOXILOGY RISK ASSESSMENT OF POLYVINYL ACETATE EMULSION
East Coast USA Analytical Chemistry Laboratory needed for Polyethylene testing: Dilute Solution Viscosity (0.02% at 135C) of UHMW-PE for determination of Intrinsic Viscosity. Number of Samples TBD.
West Coast USA or Pacific Northwest Polymer Laboratory needed for ASTM Testing to ASTM D4603. Viscometry for PET plastic 3 samples per week. Plastic PET preforms for intrinsic viscosity testing. Rapid turnaround is critical.
Government needs India Materials Laboratory for materials testing of materials used for fiberglass boats, which are currently being used.
Europe Mechanical Laboratory needed for GMW Air induction duct durability testing to GMW15143
USA or Canada Physical Laboratory needed for water repellancy testing for WATER REPELLENT TREATMENTS Compliance to Standards listed in testing requirements below. There will be three samples of products provided.
Malaysia Physical Polymer Laboratory needed for Durability Testing for Durability Dropping Impact - Dropping Impact Mass : 25kg -Input Load,F1 : 6kN ( Adjust the dropping height to achieve F1 ) -Room temperature : 20+/- 10degree C -Qty samples : 2 pcs -To measure spring characteristics and amount of permanent set in fatigue before,after test and target cycles
West Coast USA Mechanical Laboratory needed for Mechanical Strain Testing planar biaxial strain testing of thin film polymer specimens submerged in a saline solution. We are looking for the in-plane strain found through non-contact optical methods and the associated forces. There are about five different thin film membranes, each to be tested an appropriate sample-significant number of times.
USA Polymer Laboratory needed for polypropylene contaminant testing for percentage of polypropylene contaminant within a base HDPE material. 4 samples
Polymer Laboratory needed for polymer testing: thermal conductivity of polymer matrix composites and polymers? If so, 1. What kind of tests do you perform (guarded hotplate, flash diffusivity, etc)? 1. What is the price per specimen 2. What is the turn-around time? 3. What are specimen dimensions?
Food Laboratory needed for Food Packaging Testing, Migration Testing for Food Contact Surfaces (polymers, adhesives, metals, lubricants, colorants, plastics, papers)
Polymer Laboratory needed for ASTM Residual Testing: ASTM F 2013-10, Polymer residual testing in process samples and fabricated items.ASTM F 2013-10, Residual Acetaldehyde in PET by Static HS-GC-FID. We are seeking a back-up lab to handle sample overflow.
Polymer Laboratory needed for Plasticiser content testing in sample PA 11 tube of size 12x9 product in 12x 9 size. Due to crack issue we intend to check the plasticizer in the raw material granules.This is further extruded in the tube form extrusion process.Material and Tube validation data of the above grade as per DIN73378 & DIN74324 Can you help us to check plasticizer content.Pl send us quotation of time/cost and sample required to do so, ...
Europe Polymer Laboratory needed for hydrosoluble polymer testing. 5-10 samples Determination of Mn, Mw, Mp by SEC-UV-RI-MALS or A4F-UV-RI-MALS.
Canada or US Physical Laboratory needed for OECD Testing, Resin Testing to OECD 117 testing for one sample
USA Physical Laboratory needed for polymer testing at low temperature. stress-strain testing of polymers at -150C to establish stress-strain curve at low temperature -150C
India ISO Physical Laboratory needed for ISO acceptance testing of 1.1 kv 2.5sqmm pvc insulated 2rbice connection cablec Al se Acceptance Test
US Plastics Laboratory needed for rubber equivalency testing to show equivalency to component already used in product. We need to have rubber tested using this method and compare both lots. We will have 10 samples of each.
Asia, India or Europe Physical Materials Laboratory needed for ASTM Testing or ISO Testing: Thermal Testing Coefficient of Linear Thermal Expansion for Plastics
Plastics Laboratory needed for APET Sheet testing
India, Asia Materials Laboratory needed for ASTM Testing: 1) Heat Transmission coefficient 2) Rigidity - ASTM C393 3) Elongation - ASTM D638 4) Deflection Temperature under load - ASTM D648 5) Coefficient of Linear Thermal expansion : ASTM D696 6) Impact resistance - ASTM D732 7) Toxicity : should be within acceptable, TCLP 8) Colour change at 80degC : No visible change 9) Delamination at 80deg C : No delamination 10) Bending strength ...
ELECTRICAL LABORATORY NEEDED FOR IEC TESTING OF ELECTRICAL TAPES TO IEC93 AND 250JOINTS IEC 60502-4 AND IEC 1442 FOR PERMITIVITY, DISSIPATION FACTOR, SURFACE AND VOLUME REISTIVITY. ELECTRICAL JOINT COMPLIANCE TESTING.
USA Materials Laboratory needed for ASTM Testing adn FDA Testing of bioplastic materials : 1.Bio-content analysis - ASTM D6866 2.Food Packaging Contact Safety - FDA 178 3.Biodegradability - ASTM 6400 ASTM 4.As well as another biodegradability test for our durable bioplastic. This hould be some kind of controlled biodegration test that lasts between 4 to 6 months. Bioplastics used for food contact, apparel, interior automotive, toys, pet product ...
INDIA PLASTICS LABORATORY NEEDED FOR MATERIALS TESTING OF PLASTIC COMPONENT TO VERIFY WHICH IS MATERIAL AS WELL AS MATERIAL DEFINATION AS PER INDIA MARKET. REGARDS KOTEKAR
USA Plastics and Polymers Laboratory needed for Hydrolytic Stability Testing of Polurethane
India Plastics Laboratory needed for plastics testing of 2,2(1,2-ethenediyidi-4,1-phenylene bisbenzoxazole% for CaCO3% testing ,Al2O3% testing,Bulk density testing ,fineness testing
Plastics Laboratory needed for Mylar film testing for ultra-violet and visible light transmission using a spectrophotometer, or similar device.
Asia, Middle East, India Materials Laboratory needed for Plastic Jerrycan testing for UN number approval
India Materials Laboratory needed for ASTM Testing to determine the chemical and physical properieties of PTFE
Texas Materials Laboratory needed for ASTM Testing for coefficient of friction
Plastics and Polymers Laboratory needed for ASTM Testing to measure melt flow rate for epoxy according to ASTM 1238-10 or ISO1133.
USA Mechanical laboratory needed for AASHTO Testing joint to AASHTO M326-08 specification for HDPE liner pipe
Middle east Mechanical Laboratory needed for ASTM Testing to ASTM D3039, Tensile test & modulus of GRP laminates testing
Materials Laboratory needed for ASTM Testing Oxo-Biodegradable plastics testing to ASTM D 6954-04
Southern USA materials laboratory needed for high temperature GPC testing of polymer molecular weight and molecular weight distribution by GPC. There are 3 samples need to be tested. Please give us a quote on potential cost for the tests. Please note that the polymer has high molecular weight (Mn=60KDa).
India Plastics and Polymers Weathering Laboratory needed for Weathering testing for Plastic films (Humidity: 10% to 90 %) followed by tear strength.
Saudi Arabia plastics laboratory needed for plastics identification testing to identify the materials included and the percentage
Plastics Laboratory needed for analytical chemistry testing of polyethylene flame retardent concentrate (pellets) that have a make up of decabromomodiphenyl oxide & antimony trioxide and need to know the % of each
Polymer Laboratory needed for polymer testing of PET Chips imported from China (FOB Tianjin or Shanghai) 400MT per month of PET (CR-8828 - carbonated drinks) to Brazil. Please let me know how you can help us to verify this final product before the shipment!
Large Automotive Manufacturer needs India plastics laboratory for ASTM Testing ASTM D 955, % Shrinkage test for Plastics In this test, plastics molding is done in a mold cavity (dimensions of cavity are precisely measured) & after 24 hours, the dimensions of plastics molded test samples are measured. The difference between dimension of cavity to test specimen gives shrinkage & if it is divided by cavity dimension, it gives result in % shrinkage. ...
Large Medical Device Manufacturer needed plastics laboratory to verify a plastic materials part surface finish against a MoldTech Standard MT-11010 or an SPI standard SPI-B3
Large Multinational Corporation needs Canada Materials Laboratory for ASTM Flexural Modulus testing to ASTM D790 as -40°C 1 sample 5 specimens
India Polymer Laboratory needed for rubber testing for rubber compound percentage test
Europe Materials Laboratory needed for ASTM Testing: thermal conductivity measurement services to ASTM C-1461 or ASTM E1530 for fiber reinforced (glass or carbon fiber) polymer composite materials. (Number of samples: various number of samples will be measured through year 2012)
Analytical Laboratory neeed for cass test for our components .
UK Plastics Laboratory needed for PET Bottle grade Flakes testing- IV,color value, Moisture content, other plastics, PVC etc"
Asia Plastics Laboratory needed for JASO, JIS Testing, Poly Vinyl Choloride (PVC) Testing Auto Vinyl wires testing Laboratory.
USA Plastics and Polmers Laboratory needed for RoHS and REACH Certification Testing of pipette tips (Polypropylene) to certify that they compply with RoHS and REACH directives.
Plastics and Polymers Laboratory needed for plastic testing of plastic part to 21CFR177.2410
Israel Physical Laboratory needed for ASTM Testing: Burst Strength and peel strength test of plastic lidding film to tray to ASTM F1140 ASTM F2824-10 ASTM F2054
India materials laboratory needed for Polyurethane testing of tubes Parameters / Evaluation 1.Hydraulic pressure test @ 50 deg c for 1 hr (Pressure to be applied 10 bar then examine for bulging, elongation, and change in colour). 2.Bursting Pressure ( Pressure to be applied till it burst). No of samples: 2
India Materials laboratory needed for ASTM Testing for Comparative Tracking Index [CTI] for polyester film to ASTM D-3638-93