Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Mechanics Laboratories to perform their Mechanics Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Mechanics laboratory that would like more information on these Mechanics projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Clinical Sports Performance laboratory needed for clinical biomechanical testing in humans to validate performance of university's sports biomechanics equipment Simi motion analysis system, Vertigo static and dynamic balance system, Bertec force platform, Myon EMG, IsoMed 2000-dynamometer.
Mechanical Laboratory Needs to carry out following tests 1. Cyclic Uniaxial Compression Data: for instance sample is loaded in compression to achieve 10% strain, then unloaded, then loaded to 20% strain, then unloaded, so forth until achieving 50% strain 2. Volumetric Test Data Please review specification below and let me know of your questions or comments. Elastomer made from Polyurethane Nominal 92, UTEX Compound 50396 S.G. 1.19 ...
Mechanical laboratory neede for certification testing of NEMA-G11 insulating washer that we purchased from India.But our client needs a UAE based third party certificate for the same.Kindly advise us whether you are having the facility to do the same.Expecting an early reply from your side.
Mechanical Laboratory needed for Aluminium honeycomb core testing
Materials Laboratory needed for ANSI / ISA Testing to ANSI/ISA-12.27.01-2011, section 5.2.3 Fatigue Cycling, UUT are 8 typical pressure transdcuers, 4 at 1psig, 4 at 300 psig. More of same testing planned after this.
Canada Metallurgical Laboratory needed for metallurgical testing/chemical testing SEM-EDS , EDS and evaluation of a gear cracked tooth that will point to the defect root cause, ie. raw material defect, heat treat process defect, or any other cause.The part is forgedand normalized,turned (OD) and broached (gear profile), induction hardened, and furnace tempered. Part length is 130 mm; diameter (at gear OD) is 165 mm; gear tooth width is 12mm, thic ...
Mechanical Laboratory needed for mechanical testing: test one sample ACSR Zebra conductor as per BS EN 50182 for Type Test ,the detail as per below; 1) Breaking Strength Test 2) Stress-Strain Test
Mechanical Laboratory needed for load testing
USA Mechanical Laboratory needed for ASTM Testing, ISO Testing and Dynamic Mechanical Analysis for a number of mechanical tests. The tests would be as follows: 1) DMA testing of Pure Resin samples (Specimens will be cut by Materia-Inc. and sent to you for testing). Number of Specimens: 9 Please follow ISO 6721-5, with a temperature ramp from -50 C to 50 C 2) V-Notch Rail Shear testing of composite panels (Specimens will be ...
India physical laboratory needed for vibration testing
INDIA MECHANICAL LABORATORY NEEDED FOR QUALITY CONTROL MECHANICAL TESTING
India Mechanical Laboratory needed for Mechanical Testing: Dynamic Mechanical Analysis(DMA)
India or Asia Mechanical Laboratory needed for Mechanical Testing on Diesel engine: ESC, ETC and Durability on Transient Engine Dynamometer capable to run engine upto 520 HP and 2300Nm peak torque. Emissions measurement capability for NOx and NH3 @ Euro 5 levels
Mechanical Laboratory needed for Sealing Pressure Testing using method 3211 of FED-STD-601
Large mechanics company needs oil laboratory for ASTM Testing: fuel lubricity testing (according to ASTM D6079-11). Please quote for 1 fuel sample and 4 samples. Also, what is they typical turn around time?
Singapore Mechanical Laboratory needed for ISO Testing and ASTM Testing to ISO 527-1ASTM E1461ASTM D150 Tensile Testing for: Tensile Modulus, Tensile Strength and Nominal Strain @ break Dielectric for Dieletric constant and dielectric strength Thermal Conductivity
Eastern USA physical laboratory needed for Thermal Shock testing and cycling testing -40C to +55C - optical beam stability (movement and placement), mechanical shock and vibration - 1064nm free space optical component
Dubai or UAE Mechanical Laboratory needed for ASTM, API EOLCS, and ILSAC Testing: chemical,viscosity, cold cranking, NOACK Volatility, High shear viscosity Sequence test Ball RUST TEST, EOFT, EOWTT, Homogenity & Miscibility, TEOST MHI
Pune India Mechanical Laboratory needed for cleanliness testing of catalytic converter set up to determine the cleamliness/residual dirt level of catalytic coverters . Each pipe of the caton is to be evacuated by a vacuum cleaner/vacuum pump of power 2kW keeping rest of the openings air tight except one.The dirt thus collected in the filter bag is weighed to determine the mass of the residual dirt. The particles of > 1mm size are to be separat ...
Soil Mechanics Laboratory needed to conduct soil errosion, land slide, slope testing for a land in Senlangor state, Malaysia.
Europe Mechanical Testing Laboratory needed for for heavy duty metallic substrate size of D=334 mm and L=150 mm, weight being 10 kg. The test should include thermal cycling and gradients, having T max 700-1000 °C and T min 200-500 °C. How the temperature is generated, is not crucial. Exhaust gas flow would be 1000-2000 kg/h. Test could include vibration, if that's possible, but it's not mandatory. ...
US laboratory for certification of lifting appliances for lifting beams. Typical of CDE equipment pull test and NDE test
ASTM laboratory to test soft baby carrier that uses a weight, 5" diameter ball. cyclic testing with different loads.
Mechanical Laboratory needed for ASTM Testing, Tension steel according to ASTM E8M
Very large company needs USA mechanical laboratory for ASTM materials testing, fracture strength and toughness according to ASTM 1161-94
USA MECHANICAL LABORATORY NEEDED FOR ASME B31.3 CODE -320 F CHARPY TESTS, LOW TEMPERATURE CHARPY, FOR B31.3 AUTOGENOUS TUBE WELDS. .035 WALL 1/4" O.D. AND .049 WALL 1/2" O.D. (TP-316L)
Canada, USA Physical Laboratory needed for vibration testing rubber isolator that requires the natural frequency to occur at 11Hz under load. We need this verified.
Mechanical Certification Laboratory needed for ANSI, ISEA Mechanical Ratings Testing, certificate through your esteemed laboratory for our gloves as follows ; Item : Safety Gloves Description : HPPE fiber(yarn) knitted gloves, Polyurethane coated gloves
USA Analytical chemistry Laboratory needed for Dynamic mechanical analysis (DMA), FTIR gel permeation chromatography (GPC),Differential Scanning Calorimetry (DSC)
Central NJ mechanical laboratory needed for eddy current testing of stainless steel castings"
Eastern USA Mechanical Laboratory needed for ASTM F648 Testing on UHMW-PE fabricated forms, including density, ash, tensiles and double notch izod and charpy testing.
Mechanical Laboratory urgently needed for ASTM1894-93 Coefficient of friction testing. Please advise. Urgent.
NJ physical laboratory needed for ASTM A578 level B S-1GE Spec B50A656C testing of plate 1s 2 thick x 52" OD ring
A2LA Mechanical Laboratory needed for ASTM mechanical properties testing for a turbine engine compressor blade that is very small in size. Need to be able to make test specimen from the final blade configuration.
India Product Safety Laboratory needed for Product Safety Certification Kindly get us inoformation about such consultants in India Thanks
USA Physical, Mechnical Laboratory needed for Mechanical Testing: Tensile AND Torsion Testing required for Friction Welded Joint. I have 3 different companies supplying samples. I want to compare welds.
Mississauga Mechanical Physical Laboratory needed for ASME Testing of Boilers to MIL-PRF-25567E Appendix A from the asme boiler and pressure section V To test our leak detector fluids to determine if the support mold growth,
Israel physical weathering laboratory needed for optical testing of substrate that contains ~ 700 millimeter sized CPC optical elements. Whish to test actual performance under one sun conditions and compare to reverse ray analysis.
Mechanical Laboratory needed for thermal, combustion testing, glycerol combustion experiments and would like to measure the acrolein emission in the exhaust. I have following questions. 1. Do you do acrolein measurements? 2. What sampling procedure you recommend us to use? (molecular sieves or trapped gas in a container or anything else). 3. Whether you provide sampling equipments material necessary or we have to procure from other source and sen ...
Mechanical Laboratory needed for ANSI B71.1 Testing of new lawnmower
USA analytical chemistry laboratory needed for testing specific gravity, kinematic viscosity, ppm iodine, ppm hydrogen peroxide, and rheology description (e.g. newtonion or thixotropic) for mechanics company
Mechanical laboratory needed for ACSR Moose conductor testing: 1 salt-fog test 2 AC resistance & reactance test at 75deg C 3 Self Damping Test & 4 Stiffness test
Mechanical Laboratory needed for ASTM testing, ASTM D5500 and D6201 of engine deposits, while ours does not. We want comparative data to support this. (We will not publish the name of the competitor, of course) How much does this kind of testing cost?
Europe Weathering Laboratory needed for GMW 3417 natural weathering exposure test
Mechanical Laboratory needed to test newly invented rotary mechanical system without energy support.
Toronto Mechanical Laboratory needed for Rockwell Hardness Testing, material check, tensile and yield strength on fastener-type parts.
Manufacturer of compressed air filters and elements needs physical mechanical laboratory for ISO12500 validation testing of the filtration performance of our products according to ISO-8573.1
Asia Mining Laboratory needed for geomechanical testing for mineral dressing, exploration, rock analyze, geomechanics, anythings about mining software 6.metallurgy lab 7.surveying lab 8.mineralogy lab 9.blasting lab 10.structure geology lab 11.geophysics lab please send me the price and the spec. of the equipment soon..
New England bioengineering laboratory needed for testing of fracture mechanics of fresh/frozen cadaveric bones.
USA Mechanical laboratory needed to Analyze output: Oxide mass over time Method:parabolic rate
Eastern USA Geotechnical Laboratory needed for Grain Size Testing, Soil Mechanics characterization, Compressibility Testing, Total Shear Strength Testing, Effective Shear Strength Testing, Consolidation Testing, and other basic geotechnical lab analysis.
Eastern USA, California Biomechanics Testing Laboratory needed for ASTM D4020, F648-00, F2003-00, F22102-01, ASTM F2183-02 Testing for FDA 510(k) for implant orthopedics. The contractor should provide all the biomechanics testing required by FDA's Design Control Requirements, Title 21; Code of Federal Regulations Part:820.30 + ISO 5832-9:1992, ISO 5832-2:1999, ISO 5832-1:1997, ISO 5834-2:1998 The products consist in orthopedic acetabular compo ...
Geotechnical laboratory needed for Typical Soil Mechanics Testing. 1) The testing laboratory should be for both undergraduate teaching and postgraduate research. 2)The 6 months is for delivery but the offer is needed as early as possible. 3)As the funds would be from the Japanese loan to Iraq, the suppliers should be Japanese Companies.