Incoming Fasteners Laboratory Test Requests

Contract Laboratory has received the following Fasteners Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Fasteners Laboratories to perform their Fasteners Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Fasteners laboratory that would like more information on these Fasteners projects, please visit our registration page or call toll us free 1-855-377-6821.

Below are our 50 most recent Fasteners laboratory test requests. Please log in to see more.

17-01294

Fasteners

Laboratory needed for complete failure analysis of bolts that failed ASTM F3125/F3125M-15a, Standard Specification for High Strength Structural Bolts, Steel and Alloy Steel, Heat Treated, 120 ksi (830 MPa) and 150 ksi (1040 MPa) Minimum Tensile Strength, Inch and Metric Dimensions

Closed

17-01091

Fasteners

Construction materials laboratory needed for physical testing of Fiber Reinforced Polymer (FRP) Reinforcing Bar including 160 samples tested for durability in accordance with the following standards:

-AC320 (an acceptance criteria from ICC)
-Conditioned for 1000 and 3000 hours using ASTM D 2247
-ASTM C 581 Standard Practice for Testing Water Resistance of Coatings in 100?% Relative Humidity

Closed

17-00094

Fasteners

Materials laboratory needed for screw DIN Testing: 1) Screw Type: DIN7500 PE M3X8
Properties Class: 8.8
Surface protection: DIN EN ISO9227-NSS 360h
Cleanliness requirement: TV-02023-EN SKII (166mm2)

2) Screw type: DIN7500 PE M4X10
Properties Class: 8.8
Surface protection: DIN EN ISO9227-NSS 360h
Lock washer type: DIN128A M4
Lock washer material: A2
Cleanliness requirement: TV-02023-EN SKII (356mm2)

Closed

17-00069

Fasteners

Materials laboratory needed for DIN fastener cleanliness testing to Screw Type: DIN7500 PE M3X8Properties Class: 8.8Surface protection: DIN EN ISO9227-NSS 360hCleanliness requirement: TV-02023-EN SKII (166mm2)2. Screw type: DIN7500 PE M4X10Properties Class: 8.8Surface protection: DIN EN ISO9227-NSS 360hLock washer type: DIN128A M4Lock washer material: A2Cleanliness requirement: TV-02023-EN SKII (356mm2)Please advise.Thanks.

Closed

16-02439

Fasteners

Materials Laboratory needed for Adhesion tape testing for confirming Adhesiveness of tapes

Closed

16-02321

Fasteners

International security lock company needs test of a Padlock per BS EN 12320 2012

Closed

16-02294

Fasteners

Materials Laboratory needed for 3000 hour accelerated aging testing of plastic connector made from polyamide 66+ 30% glass fiber, in order to see the status after 3000 hours of functioning for our plastic item ?Connector?.

Closed

16-02189

Fasteners

Manufacturer of rubber parts needs materials laboratory for UL certification testing for a gasket.

Closed

16-01958

Fasteners

MATERIALS LABORATORY NEEDED FOR ASTM TESTING OF HOOK AND EYE TO ASTM 5169 TESTING OF SHEAR STRENGTH OF HOOK AND LOOP
ASTM 5170 PEEL STRENGTH OF HOOK AND LOOP FASTENERS

Closed

16-01829

Fasteners

Physical laboratory needed to Burst & Proof Pressure Testing to ASTM A234 WPB

Closed

16-01611

Fasteners

Mechanical Laboratory needed for ISO mechanical testing to ISO 594 Testing of Conical Luer Fittings

1. Luer Assembly: Ensures that the Luer specimen can be assembled with minimum axial force and torque.

2. Separation Force: Ensures that the Luer specimen remains attached to the reference fitting when an axial load is applied.

3. Unscrewing Torque: Ensures that the specimen Luer remains attached under a specific unscrewing torque in the counterclockwise direction.

4. Resistance to Overriding: Ensures that the threads cannot be overridden by a specific screwing torque in the assembly clockwise direction.

Closed

16-01511

Fasteners

Certification laboratory needed for Copper and Aluminium Cable Lugs testing for UL Certification

Closed

16-00668

Fasteners

Contract Laboratory needed for IEC Testing of Copper tubular Cable lugs, Connectors to be tested as per IEC 1238-1:1993.
AS/NZS 4325.1:1995
.

Closed

16-00626

Fasteners

Non-Destructive NDT Laboratory needed to provide a quote for the failure analysis of a failed CW pump bolts.

We require doing the following testing:

? Digital photography
? Visual examination
? Physical measurements
? Corrosion examination (Corrosion deposits)
? Fractographic examination
? Metallographic examination (Microhardness, microstructure characterization)
? Mechanical properties (Tensile and chemical analysis)

Your immediate response is highly appreciated




Regards,
Czar

Closed

16-00013

Fasteners

Mechanical Laboratory needed for Strength testing of welded eyebolts. Test to failure the tensile strength of 5/16" eyebolts with 3" diameter welded eyes. We have been asked to verify that the bolts will conform to ANCI B30.2 standard

Closed

15-01914

Fasteners

USA Laboratory needed to test aluminum washers according to ISO 16232-5/6/7/8/10 including metallic and non metallic parts, residue wt (mg/cm^2), number of particles / cm^2 (>100, 200,300,600 um)

Closed

15-00613

Fasteners

Physical Laboratory needed for UL Certification Testing for UL - CERTIFICATE (FIRE RESISTANCE CERTIFICATE) FOR Gypsum BOARD STEEL PROFILE (FASTNERS)Gypsum BOARD STEEL PROFILE (FASTENERS)
OMEGA, C-CHANEL, PERIMETER ANGLE

Closed

15-00390

Fasteners

FAA Aerospace Certification laboratory need for certification testing of fasteners to FAA form 8100 or 8130 for aircraft use to pass fire safety. Needs to pass FAA regulations 25.853(a) for flammability.

Closed

15-00233

Fasteners

Physical Laboratory needed for corrosion testing of Rubber rotary shaft seal for washing machine to material specification which include a rust mark test ,rubber compress between two stainless steel plates @95oC 48h in %1 persil solution ,the rust mark occur after the test.

Closed

14-00726

Fasteners

Ontario Canada A2LA or ILAC Materials Laboratory needed for ASTM Testing: Material testing of automotive fasteners. Hardness testing rockwell c and others. Thread verification, plating thickness, chemical composition of metals and coatings. Salt spray testing. Tensile and shear. Optical comparator for dimensional. Gauge calibration and Gauge R&R.

Closed

14-00651

Fasteners

Mechanical Laboratory needed for National Aerospace Standard Metric NASM Testing of brass nut products according to NASM 25027, Nut, Self-Locking, 250F, 450F, and 800F. Could have the quotation about the mechanical properties first.

Closed

14-00036

Fasteners

Metallurgical Laboratory needed for Metallurgy Testing: DIN microstructure testing on Titanium Fasteners manufactured to DIN 912 Hexagon socket head cap screws and DIN 963 Slotted Flat Head Countersunk. They are use in outer space.
There are 6 sizes and we need 1 or 2 samples from each size to be tested and the results to be presented by photographs and confirmation on whether the fasteners comply with the customers requirement.

Closed

13-01357

Fasteners

Materials Laboratory needed for Metallurgical Testing of Retaining rings made out of 303 Stainless Steel per Silver getter testing per Delphi DX900419

Closed

13-00223

Fasteners

Manufacturer of Fasteners need materials laboratory for JDS Testing: cleanliness per JDS-G169. What do you need to perform testing? How much is testing? How long does testing take? What do you need to perform the test? How many samples? What is involved with this test?


Closed

13-00198

Fasteners

Mechanical Laboratory needed for IEC Testing of COPPER TUBE TERMINAL IEC 61238Compression and mechanical connectors for power cables forrated voltages upto 36 kV (Um = 42 kV) -Part 1: Test methods and requirements

Closed

13-00150

Fasteners

Europe ILAC electrical laboratory needed for Type Testing on a 6.6kV trailing cable of open cast mining to Australian Standard AS2802Type 450.6 Trailing cable in an ILAC certified laboratory

Closed

12-2259

Fasteners

Physical Laboratory needed for DIN Testing Fogging Testing to DIN 75 201 Fogging Test

Closed

12-1026

Fasteners

Canada Mechanical Laboratory needed for ASTM Testing of threaded fasteners to astm f606-11a

Closed

11-01939

Fasteners

Power and Energy Company needs Metallurgical Laboratory for Metallurgy / Corrosion testing of #14 x 3" screws tested to determine the cause of corrosion (environment or dissimilar metals)

Closed

07-0334

Fasteners

Mechanical laboratory needed for fatigue testing of engine fasteners

Closed

07-0259

Fasteners

Asia Mechanical lab needed for CES Fatigue strength testing for fasteners as per CUMMINS Engineering standard CES 14250 and CES 14338

Closed

06-1058

Fasteners

A2LA mechanical laboratory needed for ASTM, IFI, and CNLA Dimensional and physical testing of fasteners(Nuts, bolts, screws)

Closed

Submit Fasteners Testing Requests for Fasteners testing and Fasteners Scientific Research