Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Construction Laboratories to perform their Construction Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Construction laboratory that would like more information on these Construction projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Construction laboratory needed for materials and toxicity testing of naval thermal insulation testing to various standards including: NCD 1427 : SPECIFICATION FOR MINERAL WOOL MARINE BOARD FOR THERMAL AND ACOUSTIC INSULATION ON BOARD INDIAN NAVAL SHIPS
NCD 1433 : SPECIFICATIONS FOR ELASTOMERIC NITRILE THERMAL INSULATION FOR USE ONBOARD INDIAN NAVAL SHIPS
LEGAL Materials laboratory needed for performance, weathering and failure investigation testing of potentially defective, two coat, acrylic elastomeric liquid coating used for roofing on commercial building. Polymer coating that instead of coating and drying within two hours discharged into storm drain causing notification of Fire department and Hazardous Materials units.
Engineering company needs materials laboratory for environmental simulations testing of GRP (Glass-Fibre Reinforced Plastic) ground anchor for UV stability testing in accordance with ES ISO 4892-2 , performance at elevated temperatures is in accordance with ACI440.3R-04 Section B.6 Accelerated test method for alkali resistance of GRP bars, and suitability, Durability,
Construction company needs materials laboratory needed for ASTM testing of insulation material to ASTM C1371 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers , emissometer, emittance and ASTM C1549, Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer. Company from Turkey.
Materials Laboratory needed for AASHTO testing of Architectural coating Material to Chloride penetration test (AASHTO T259, T260) Rapid chloride Permeability AASHTO T277 C02 Permeability Coatings and Films Materials laboratory for ASTM paint testing 1. Anti-carbonation: Test method EN-1062-7 2. Liquid water permeability: Test method EN-1062-7 3. Acid Resistance . 4)SRI
Urgent Need by Large UAE construction company for testing of foam materials per BS EN 13468 (Thermal insulating products for building equipment and industrial installations. Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH) and (AGI Q135).
Building Supply company needs laboratory to test thermal insulating products for building equipment and industrial installations. Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH per BS EN 13468 test for insualtion foams
Laboratory needed for multiple testing on tape product AAMA 713 AAMA 711 AATCC 127 ASTM D412 ? Tensile Strength ASTM D 1970 Water Penetration ASTM D 3300 Adhesion and accelerated aging (multiple Tests) ASTM E331 For Exterior breather membrane : - ASTM D-1117 ASTM-D882 ASTM E2178-11 ASTM E2357-11 ASTM E96 Method B AATCC 127 per AC38, ASTM E84 and UV exposure/aging NFPA 285,
Airtight interior membrane: - http://www.astm.org/Standards/E2178.htm
ASTM D-1117 ASTM-D882 ASTM E96 Method B AATCC 127 per AC38, ASTM E84
ASTM Testing of aluminum honeycombs to multiple ASTM standards: .ASTM C273 - Standard Test Method for Shear Properties of Sandwich Core MaterialsASTM C365 - Standard Test Method for Flatwise Compressive Properties of Sandwich CoresASTM C297 - Standard Test Method for Flatwise Tensile Strength of Sandwich ConstructionsIf you offer testing of aluminum honeycomb core, please provide a quote the three tests and for multiple honeycomb cell size.
Materials Laboratory needed for ASTM Testing of Processed woodcore Panel Board assemblies (using core material such as MDF / Particle Boards, Laminates, Edge Banding etc etc ).We are looking for Test Certification for ?ASTM E84-06a? for surface burning characteristics of the Finished Panel Board assemblies (where we would like for the Test to make specific reference to the actual assembled components for Wood-core Panels including core, Laminates and Edging.
Large company needs materials laboratory needed for accelerated aging study on thermoset material with for yellowing index and light transmitting to identify the relationship between the hours accelerated test and the years of outdoor exposure.Please, send me the costs for tests and measurements and samples dimensions.
Construction Buildings Materials company needed for ANSI or ISO adhesive testing to ANSI A118 or ISO 13007 Test adhesive tensile strength at normal temperature and water immersion *Determination of tensile adhesion strength - C *Determination of open time * Determination of slip
Independent laboratory needed for LED comparison study of 4 manufacturer's underwater LED light components to evaluate Quality of construction ? Quality of LED components ? Quality of LED Drivers ? Color Temperature output from each ? Lumens output from each- Underwater Lumens from each ? Projected beam angles from each ? Thermal temperature from each - Are the LED?s in spec with required approvals - I would also like the ability to test the results both in air and under water? I would also like to determine a baseline for which colors travel furthest in salt water or brackish water conditions. I prefer the test to be completely independent.
Materials laboratory needed for DIN and ASTM Testing of thermal insulations foam board. Testing to To meet out the requirement of Density: DIN 53420(ASTM D 1622 Thermal conductivity :DIN 52612 OR 52616 Compressive strength :DIN 53421 (ASTM D 1621 Water vapour diffusion resistance factor: DIN 52615 Water vapour permeability : ASTM C355 Heat soaking : DIN 52328 Water absorption by submersion : DIN 53428 (28 days submersion) ASTM D 2842
Electrical Laboratory needed for battery testing for charges of following test as per IS 1651, Stationary cells and batteries, lead-acid type (with tubular positive plates)
Cell Details : 2V, 100Ah.
1. Test for capacity 2. Test for voltage during discharge. 3. Ampere hour and watt hour efficiency test. 4. Test for loss of capacity on storage. 5. Endurance test, 1500hr cycle testing. 6. Verification of constructional requirement. 7. Verification of marking. 8. Verification of dimensions.
Accredited UK laboratory needed for construction building products testing of flexible sheets for waterproofing to BS EN 12691, Determination of resistance to impact BS EN 12730. Determination of resistance to static loading and EN 1847 for building products. Methods for exposure to liquid chemicals, including water
Construction Buildings Laboratory needed for ASTM Testing for Prefabricated Vertical Drains 1. Width ASTM D 3774 2. Thickness ASTM D 5199 3. Discharge Capacity qw , straight & folded ASTM D 4716 4. Tensile strength, elongation at break, elongation at 1kN (full width test) ASTM D 4595 5. Apparent Opening Size O95 ASTM D 4751 6. Permeability, permittivity ASTM D 4491 7. Grab tensile strength ASTM D 4632 8. Trapezoidal tear strength ASTM D 4533
Larg Construction Building Materials company needs certification laboratory for ANSI Testing of tile adhesives & grout accoding to ANSI standards. FK10W Cementitious tile adhesive C1T EN 12004 GM1 Cementitious tile adhesive C2T EN 12004 FLS1000 Cementitious tile adhesive C2TES1 EN 12004 DB2000 Cementitious tile adhesive C2TE EN 12004 COLORFILL Cementitious joint grout CG2 EN 13888
Please provide pricing for quots.
Marble quarry need laboratory for ANSI testing of 4 products. Quarry makes marble blocks, as raw material in order to produce high quality building materials of ready mixed mortars, tile adhesives, waterproofing materials, additives and amplifying fluids. o increase our export possibilities we have chosen the 4 following adhesives and joint grout products for testing under the ANSI standards (Standard and optional performance characteristic). ? tile and marble adhesive, tile and marble adhesive, tile and marble adhesive, Colorfill, Joint grout, 2-8 mm, for tiles and slabs, ceramic or natural stone. Please inform us about the cost, payment terms and all the details and the accompanying documents that are necessary to send the test samples such as packaging, quantity of the sample, testing time
Geology laboratory needed for geophysical testing: Size, abrasive index, moisture content, bulk density, gradation
These tests need to be done on limestone and gypsum rock samples.
Noise control company needs RFQ from India acoustics laboratory to provide a quote for noise level testing of acoustics treated product: insider bench test room at outside ambient noise levels.
ISO Materials laboratory needed for ASTM PMMA panel testing to US Standards, ISO and EN standards. ASTM E90 and E413, ASTM D-638 : tensile properties, ASTM D-790 : flexural properties, ASTM D-1003 : luminous transmittance, ASTM D-635 : burninjg of plastic, ASTM D-1929 ignition temperature. We also need to do the TL-4 inside the Report 350 (crash test safety performance). Thank you so much. Regards.
Physical Laboratory needed for acoustics testing of Light Weight Hollow Core Precast Cement Wall Panels for sound absorption and transmission
INDIVIDUAL Analytical Chemistry laboratory needed for asbestos testing in insulation.
Large company needs Canada Laboratory for Sound Transmission loss testing of an exterior residential wall assembly
Calgary analytical chemistry laboratory needed for Asbestos testing for house. Popcorn ceiling, drywall, and flooring sample.
Accredited Laboratory needed for the Testing of Earthing Enhancement Compounds. Laboratory needed that is able to do all the tests listed below:
a) Leaching test according to EN12457-2 and EN12506 b) Sulfur test according to ISO 14869-1 c) Determination of resistivity according to ASTM G57 d) Corrosion test (Linear Polarization Resistance (LPR) according to ASTM G59-97 and G102-89)
Corporation with quarry needs quartz ore tested for different properties including gloss, clearness, color, density and else.
USA UL certification laboratory needed for conveyor system testing (brand hytrol), with 3 electrical control panels the individual components in the panel box are all ul listed but the panel box is not we need a certificate for our final inspection that requires the box to be safe
Europe accredited laboratory needed with accreditation for the scope of the test method in accordance with
- EN 13500 - Thermal insulation products for buildings. External thermal insulation composite systems (ETICS) based on mineral wool. Specification - Sample to be tested: Plastic - Qty: 4 Please send sample size required and turnaround time expected.
For further information, please feel free to contact me. Your prompt support would highly appreciate.
Southeast USA electrical laboratory needed for electrical control panel testing of installed a conveyor system (brand hytrol), with 3 electrical control panels the individual components in the panel box are all ul listed but the panel box is not we need a certificate for our final inspection that requires the box to be safe
EPA LEED, USGBS Environmental Laboratory needed for Formaldehyde Testing in building products. Laminate truss, urethane foam adhesive, wallboard, blown in fiberglass insulation Looking for off gas rates and comparison with accepted limits vis a vis EPA, LEED, USGBC, and the like.
Physical Laboratory needed to perform Salt Spray (fog) test for PTFE coated bolts (Fastener) as per ASTM B117
University Researchers need Asia sensory laboratory for slow release fragrance technology testing for markets in Asia.
Manufacturer a counter top material with recycled window glass and an epoxy resin binder needs physical laboratory for NSF / ANSI / ASTM Physical Properties Testing Food Safety:NSF/ANSI 51 compressive strength, tested to ASTM C39 Absorption, tested to ASTM c-97-02 Sctratch Resistance/Mohs Hardness Modulus of Rupture, tested to ASTM c-99 Radon Emissions, compared to EPA-402-r-92-004 PH Miscibility(in water) Density Bending Stress Coefficient of thermal expansion Autoignition Temperature Fire point
Materials Laboratory needed for Physical Testing of Chromadek faced, EPS filled, sandwich panels. Load testing Strength testing Air/water permeability Fire resistance Acoustic behavior and more to SANS 54509:2014 / EN 14509: 2013
USA Materials Laboratory needed for ASTM Testing ASTM D2137-11 brittle point determination done on EPDM and TPO samples, as our machine currently broke down. I would like a quote for 1 sample, but I'll likely have between 5-10 samples for testing.
Road construction company needs India environmental laboratory for black trap stone aggregate testing
Materials Laboratory needed for ASTM Testing: Thermal Emittance ASTM C 1371 and Solar Reflectance ASTM C 1549. I need information of the price for each test and the time it will take to make the test. And of course the specification of the sample you will be needing to test.
ISO 17025 certified Laboratory needed for conducting some tests on new metal roof shingles that would be distributed to the US market. These certification tests need to be done in the next few days All testing shall be done per ICC AC166 specifications and they are:
- Wind Uplift Test per UL 580 and UL 1897 - Fire Resistance (Class A Material) per UL 790 and ASTM E108 - Impact Resistance (Class 4 Material) per UL 2218 (To include Foot Traffic Testing) - Blowoff Resistance Test per ASTM D3161 - Moisture Protection Test per AAMA 501.1 and ASTM E331
Please provide us with quoted amounts for the aforementioned tests, the amount of time and material required for their completion at your earliest convenience. And also include a breakdown of the cost for each test performed as described above. In addition, a summary of your accredita
URGENT: Materials Laboratory needed for ANSI fiberglass panel testing for 2 different fiberglass panels. Burn test, flex test, and drop ball test.
Physical Weathering Laboratory needed for Awning testing for snow and wind load. Determine load carrying capacity
Physical Laboratory needed for UV testing of plastic roof vent . We want ton know how this vent will age and/or long it will it the life expectancy is for this product.
Materials Laboratory needed for ASTM Testing; SRI Value Reflectance value which is measured according to ASTM E 903, ASTM E 1918, or ASTM C 1549. Emittance value which is measured according to ASTM E 408 or ASTM C 1371.
California construction materials laboratory needed for ASTM waterproofing testing of liquid applied to foundations for - functionality - thickness - de-lamination/ adhesion - bubbling
European manufacturer needs Florida or USA Physical Laboratory for ANSI Testing: System testing to the US Market. Their systems are describe below: 1. Prop formwork system for slab. 2. Load-bearing scaffolding system fro slab. 3. Frame formwork system for walls and columns.
Asia materials laboratory needed for thermal insulation testing or r-value measurement of concrete wall panel
Europe, Holland or Germany Construction Materials Laboratory needed for test method development. Lab that is capable of developing compressive strength test, moisture content, bulk density, drying shrinkage, and modulus of elasticity to ASTM C1693-11
Materials Laboratory needed for NFPA Testing of Wood Panel to pass testing to meet the NFPA 701 fire retardant requirements
Third Party Acoustic Laboratory needed for ASTM Testing:acoustics test on Acoustic Wall, Ceiling and Floating and the test are; 1. Field Sound Transmission Class (FSTC) 61 in accordance with ASTM E413-87 2. FIELD IMPACT INSSULATION CLASS 46 in accordance with ASTM E 1007-97.
Texas Certified Laboratory needed for Tex 1001-S, evaluating pavement ride quality. Testing laboratories need to be certified or validated in this area of expertise
Physical Laboratory needed for coatings testing of Bituminous waterproofing membrane for concrete bridge decks. Number of sample: 1 type We need laboratory tests according to standards: ? EN 13596 ? EN 13653 ? EN 14691 ? EN 14692 ? EN 14696 ? EN 14694
Materials Laboratory needed for ASTM Testing : Solar Reflectance Index (SRI) test report of granites according to one of the following methods.
ASTM E903, ASTM E1918, ASTM C1549.
Waiting for your revert.
Waterproofing company needs physical laboratory for weathering testing: insulation properties test for concrete in minus 30 degree
Engineering Laboratory needed for BS 6853: 1999 Code of practice for fire precautions in the design and construction of passenger carrying trains-passenger train design and construction of General Specification for Fire
- Smoke Density - Toxicity
Large engineering firm needs Middle East Laboratory for Acoustics Testing for GRP (Glass Reinforced Gypsum) panels will be used on the project. These panels must be fulfilled NRC=0.9 requirement.
Samples are available for testing. Drawing might be shared if it's required.
Preclinical COntract Research Organization needed for preclinical studies and biocompatiability testing of medical device implant: implantable membrane for breast reconstruction (tissue reinforcement matrix, class III device), to be associated with tissue expanders and breast implants.
The membrane is a modification of an already implantable silicone membrane, which is modified on the surface by plasma treatment. We would like to know if possible an estimation of the costs and timeframe for the biocompatibility tests in your facility.
Germany materials laboratory needed for ABNT and ASTM Testing: Routine test for galvanized material according ABNT (Brazil), standards, or you can propose ASTM or ISO -DIN, equivalent standard.
Product: Transformer base ( 900x900 mm,20 mm thicknes), test no.1 and 2. For test no. 3 : sample of 100 x 100 mm
Europe accredited ad member of NANDO materials laboratory needed for flooring system (polyurethane), test on dynamic crack bridging ability in acc. EN 1062-7, method B, class B3.2
URGENT: Asia forensics laboratory needed for drilling project failure analysis. 3rd party lab which can analyze the reason of broken pipe and swivel.
This is one of the urgent issue on a large Drilling work. This is a work making the underground tunnel for pipeline. (make the underground tunnel and put at there the pipeline by pulling) Unfortunately, one of drilling pipe was broken during the drilling work and a swivel was broken during the pulling time.
Now we try to found out the exact root cause why the equipments are broken for the preventive any more incident.
If you want more detail I will give to you the drawing and picture.
Russia Mechanical Laboratory needed for ASTM Testing: Tensile strength for fiber-reinforced polymer bars to possibility using this product in construction Engineering. Number of samples -5.
Puerto Rico geology laboratory needed for rock testing. Iron testing for the amount of iron and other minerals present in the sample. Can you do this and how would it cost?
Florida materials laboratory needed for ASTM Testing: testing permeability of material to ASTM C1701
Middle East, Asia or Europe materials laboratory needed for ASTM Testing. Concrete Paver test is required as per ASTM C 67: Freeze-thaw resistance
Physical Laboratory needed for stress testing: Need load/stress analysis testing on welded support I beam
India Materials Certification Laboratory needed for PPGL sheet testing certification
Physical Laboratory needed for DIN Testing: HVAC Hydronic radiant ceiling panel testing
California Materials Laboratory needed for construction materials testing of Concrete Aggregates to ASTM E228-11, Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
Physical Laboratory needed for weathering testing of sheds: accelerated weathering test according to the Sub-Clause 9.3.2 of IEC 62217:2012 standard which refers to ISO 4892-2:2006 standard ->Xenon Arc method. The test object is the shed and housing material of polymeric HV insulator. 3 samples (~10x10x0.5cm)
Europe materials laboratory needed for cement testing: analyse the physical and chemical differences we are observing in the GRINDING AID we are using in cement mills
Pakistan materials laboratory needed for BS Testing: Fire Proof testing of paint to BS STandard BS476, Method of Determination of the fire resistance of non-load bearing elements of construction Fire Proof Paint
India electrical laboratory needed for IEC Testing Cable tray/ladder system as per International Electrotechnical Commission IEC 61537, Cable management - Cable tray systems and cable ladder systems in india.
Large corporation needs materials laboratory for Cement Testing. Tests performed to standard IEC62561-7.1. Resistivity2. Corrosion Material to be tested:
Carpet Company needs Materials Laboratory for ASTM Testing: ASTM E 1477 Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers? Please advice me about sample size and the fee for test.
Northeast USA Materials Laboratory needed for ASTEM Testing to ASTM D3018, Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules
North America materials laboratory needed for DIN Testing of hydronic radiant heating and cooling panels per DIn standards
Canada Materials Laboratory needed for Aggregate testing. Electrical Resistivity Testing on Aggregates in Ontario or Canada.
Materials Laboratory needed for ASTM Testing on dry wall for the following ASTM standards: ASTM International standards ASTM E 72 strength ASTM E 96 water vapor transmission ASTM C518 Thermal transmission ASTM E 2099 structural transmission ASTM E331 water penetration ASTM D3273 mold mildew growth ASTM E 84 surface burning flame spread zero I need to know if your company can do? Please specify the cost for the testing
Construction materials laboratory needed for acoustical testing: ISO and ASTM Testing for sound transmission Loss and absorption for building products ASTM E90 or ISO 140-3ASTM C423 or ISO 354
Materials Laboratory needed for strength testing to compare rotating beam corrosion fatigue strength of stainless steel with that in air. Specifically testing to 10,000,000 cycles at stress levels in the range of 35ksi to 90 ksi in concentrated chloride solutions at elevated temperatures (80°C) Specimen preparation is required with sub microm surface finish.
Europe chemistry laboratory needed for chemical analysis for chemical composition by X-ray fluorescence spectrometer EXPERT-4L and ICP spectrometer OPTIMA 2100.Determination structure XRD method (DRON 4-13.01 Cuka radiation) and single crystal diffraction method ( BRUKER APEX II Mo radiation).Phase identification ASTM PDF6 database.5 samples of citrates: selenium germanium, zinc, copper, molybdenum sent via postal-services in glass bottle in a paper box.
NJ MATERIALS LABORATORY NEEDED FOR ASTM TESTING: STONE TESTING OF LIMESTONE TILES USED AS A BUILDING MATERIAL TO LIMESTONE BUILDING MATERIALS SPECIFICATION
LIMESTONE WAS IMPORTED FROM THE MIDDLE EAST
NEW JERSEY MATERIALS LABORATORY NEEDED FOR ASTM TESTING: SPECIFICATIONS OF LIMESTONE TILES (BUILDING MATERIALS)
Europe Materials Laboratory needed for Construction Products & Building Materials Testing
California Laboratory needed for physical testing on asphalted Kraft paper (building product)samples, 3 different basis weights on the following: DRY TENSILE STRENGTH (ASTMD828) WATER VAPOR TRANSMISSION (ASTME96 Desiccant method at 74.3) WATER RESISTANCE (ASTMD779) *ALL PER REFERENCE AC38 SECTION 3.1 & TABLE 2 acceptable to ICC-ES
Materials Laboratory needed for mechanical testing: Average Bending Strength - AS/NZS2908.2- Density (oven dry) - AS/NZS2908.2- Watertightiness - AS/NZS2908.2- Water Absorption - ASTM C1186- Moisture Content - ASTM C1186- Dimensional Conformance - AS/NZS2908.2- Warm Water Resistance - AS/NZS2908.2- Freeze-Thaw Resistance - AS/NZS2908.2- Soak-Dry - AS/NZS2908.2- Average Specific Extinction Area - AS/NZS 3837- Thermal Conductivity - ASTM C518- Non-Combustibility - AS 1530: Part 3- Abrasion Resistance - AS 1580 Method 403.1- 450 Degree Board Fire Test - In-house Method- Heat-Rain Durability - AS/NZS2908.2- Moisture Content - ASTM C1186- Dimensional Conformance - AS/NZS2908.2- Warm Water Resistance - AS/NZS2908.2- Freeze-Thaw Resistance - AS/NZS2908.2- Soak-Dry - AS/NZS2908.2- Average Specific Extinction Area - AS/NZS 3837- Thermal Conductivi
India materials laboratory needed for physical testing for trussless roof sheeting by galvalume sheets
Physical Laboratory needed for AASHTO Testing. mass concrete volume stability testing for hydraulic structure for Coefficient of thermal expansion: AASHTO T336
Toronto environmental laboratory needed for material testing of HVAC vent in condominium.
Materials Laboratory needed for ASTM Testing: Conduct Bidirectional Reflectance Distribution Function (BDRF)analysis on a proprietary daylight redirecting window film
Manufacturer of UPVC roofing sheets needs materials laboratory for ASTM Testing to ASTM D4434/D4434M-11 ?Standard Specification for Poly(Vinyl Chloride) Sheet Roofing ? - ASTM D6878/D6878M-11a ?Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing? - CAN/ULC-s107-10 ?Standard Methods of Fire Tests of Roof Coverings? - A123.21-10 ? ?Standard test method for the dynamic wind uplift resistance of membrane-roofing systems? - ANSI/UL 790, "Standard Test Methods for Fire Tests of Roof Coverings" (ASTM E108 and ANSI/NFPA 256). - UL 2218, "Impact Resistance of Prepared Roof-covering Materials." Kindly inform us if you can perform the above mention test. and please quote us. regards dharmik shah export manager email: phonenumber:
Canada or USA physical laboratory needed for NFPA Testing: Fire testing on textiles used in the production or roller type window shades to NFPA 701
Toronto materials laboratory needed for stone testing a new type of stone - chemical testing, durability testing, toxicology testing for any environmental toxins, etc. (stone needs to be proven Ok for construction - building houses; the stone need to be durable enough to surive (not to crack) during temperature changes (from hot to cold and vice versa).
Large multinational corporation needs New York materials laboratory for ASTM Testing: geotechnical analysis Testing for construction design and permitting for same.
Large Manufacturer needs physical metallurgical laboratory for metallurgical testing: ASTM Testing to measure fracture energy of drop weight tear test (ASTM E 436) on high strength pipe grades 13 mm thick.
Materials Laboratory needed for ASTM Testing to ASTM D5385. Hydrostatic pressure resistance testing per ASTM D5385Multiple samples of various construction details that we wish to determine the hydrostatic pressure resistance. We would need to know capacity - how many tests can be performed at a time, What the turn around time would be including 28 day concrete cure.
NY physical materials certification laboratory needed for plywood testing for age and or date of manufacture. Carbon test to broad need date to be as close as possible. Maybe material that holds veneers together or some other method of course you would know better than I. Thank you for your time and consideration.
India construction laboratory needed for failure analysis of factory building to analyze each existing building factory building for durability and strength.
Canada analytical chemistry laboratory needed for Canola oil contamination testing on an EPDM roof that is going to be repaired. The tenant paying for the repairs and the property manager dispute the size of the repair area. The size of roof area to test is approximately 100' by 80'. We just need to know if the contamination extends to the boundary of the size I listed, or how far approximately. This would require some test samples from various points towards the outside of the test area, say within 40' of the perimeter. ay ten tests. Oil there yes or no from visible wind blown oil drops? Building in Richmond, BC, Canada.
Middle East Materials and Physical Chemistry Laboratory needed for cement testing: 1- PSD: Particile size Distripution test of cement 2- Grind ability test: of clinker & Gypsum thanks
South Florida Materials Laboratory needed for ASTM Testing for PSI and adherence of an additive to cement/stucco mix.Need ASTM approval.
South Africa Laboratory needed for ISO testing to ISO 2531, Ductile iron pipes, fittings, accessories and their joints for water applications hydrostatic pressure testing of ductile iron pipes with a concrete lining. The pipes are 1.4 m long and 500 mm diameter. Two pipes are to be tested.
Sweden, Finland, Lithuania, Estonia, Poland Physical Laboratory needed for acoustic testing for construction materials and fire resistance testing for construction materials
Environmental Laboratory needed for salt testing of river sand. The sand is to be used for construction purposes in concrete work
NY construction laboratory needed for air quality testing, mechanical systems testing, plumbing testing, life safety systems testing, building interconnect testing, structural connections testing
Canada Materials Laboratory needed for ASTM Polymer Testing E90 ASTM (Measurement of Airborne Sound Transmission Loss) test for a polymer-wall panel and we are looking for a acoustic laboratory which is able to do so, preferably in Ontario or closet distance to London ON. (Except NRC,ottawa)
China Physical Laboratory needed for building material structural testing of light weight concrete wall panels test for structural behaviour in compression and bending
California physical laboratory needed for stress testing to find the maximum foot pounds that the apparatus is good for. The apparatus is designed to pull wire from a location where it is stuck.
Middle East Physical laboratory needed for acoustics testing: lab testing of acoustic panels (specimens - wooden panels, fabric panels), absorption coefficient, noise reduction coefficient
China physical laboratory needed for stuctural behaviour testing of wall panels for structural behaviour in compression and bending to find a role as loadbearing walls in general building applications
USA Physical Radiochemistry Laboratory needed for radiation emissions testing from foam with Tourmalin
Asia mechanical laboratory needed for cable joint testing to BS EN 50393/HD631 Test methods and requirements for accessories for use on distribution cables of rated voltage
Qatar physical laboratory needed for relaxation testing: 1000 hours relaxation test for prestressing strands
USA Materials Laboratory needed for ASTM Testing of flat coupons to ASTM E408, Standard Test Methods for Total Normal Emittance of Surfaces Using Inspection-Meter Techniques
Europe physical laboratory needed for ASTM Testing: Hydrostatic pressure testing test for waterproofing material as per ASTM D5385
Asia Physical lightning certification laboratory needed for certification testing for early streamer emission(lightning protection system)
USA Physical Laboratory needed for physical testing. Need about 5 different metal construction brackets tested 3 trials each test. most brackets will be tested in 1 direction. 2 brackets will be test in more 2 directions. This would be load testing until failure or deformation.
USA Materials Laboratory needed for ASTM Testing to ASTM D7490-08 to Measure surface tension - energy of glass windows
Canada physical materials laboratory needed for ASTM Testing: thermal & fire testing for 2 construction materials: an insulation material and a flooring underlay.
Environmental Laboratory needed for Air conditioner testing according to AS/NZS 3823.2:2011, GB21455-2008"
India materials laboratory needed for water proofing testing totest water resistivity of Water proofing membrance at specified pressure at different movement(radial movement & tangential movement)
USA Southwest or Southeast Acoustics Laboratory needed for ANSI Testing to ANSI S3.1 (Ears covered) Maximum Permissible Ambient Noise Levels for Audiometric Test Rooms
INDIA MATERIALS LABORATORY NEEDED FOR INDIA STANDARDS CODE TESTING: TESTING OF ALUMINIUM CABLES,COPPER CABLES , ITS INSULATION/COPPER CONTENTS (as per INDIAN STANDARD CODE)
Physical Laboratory needed for ASTM testing foam insulation for tensile strength to ASTM D1623, Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics at cryogenic temperatures (-265 F / -165 C). Can you do such testing? If so, can you provide me a rough budgetary cost to perform this testing in 3 directions on one type of foam insulation? The foam is polyisocyanurate with a density of 2.5 lbs/ft3 (40 kg/m3). The expected tensile strength is around 265 kPa (38.4 psi). The foam samples would probably need to be glued to a metal fixture for the testing since grips would be unlikely to work.
If you cannot do this type of testing, do you know of any labs that can? Thank you for your time.
Pacific Northwest USA Materials Laboratory needed for ASTM Testing to ASTM C 423, Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method 8 x 8 sqft samples
Construction Materials Laboratory needed ffor insultation testing:Sound absorption of various insulation materials. Materials such as fiberglass insulation.
Asia Materials Laboratory needed for ASTM Testing Thermal Insulation Material to ASTM C303, ASTM C411, ASTM C356, ASTM C177, ASTM C167, ASTM C612, ASTM C1104
USA forensics laboratory needed for Furfurylamine testing - one sample of construction debris collected from a fire.
Materials Laboratory needed for ANSI Testing of masonry bits need testing of products to meet ANSI standards.
UK physical laboratory needed for optical testing.. Compare light transmittance between two touch sensor variants.
Construction 1: 4mm plain glass 125µm PSA PET hard coat film AR film
Construction 2: 4mm AG glass 125µm PSA PET hard coat film
International mining company producing aggregates for the construction needs oil laboratory for scheduled oil sampling (SOS)of our crushing and screening Equipment.
US Construction Engineering Laboratory needed for salvage structural stell testing of World Trade Center salvage. We would like to know what melted the structural. Nanothermite are what
Northern Virginia Certified Laboratory needed for ASTM Testing to ASTM 1274, Standard Test Method for Measuring Pavement Roughness Using a Profilograph. Testing laboratories need to be certified or validated in this area of expertise.
INDIA MATERIALS LABORATORY NEEDED FOR ASTM TESTIN OF POWDER FORM, NON-HAZ, CONSTRUCTION MATERIAL WHICH IS USED WITH CONCRETE TO ASTM C1240, Standard Specification for Silica Fume Used in Cementitious Mixtures STANDARD: AS PER THE ASTM C1240 STANDARD PACKING: JUMBO BAGS OF 900 KGS WITH SHIPPING MARKS, PALLETIZED SHIPMENT: CONTAINERIZED QUANTITY: 500 MT INSPECTION REQUIREMENT: PRE-SHIPMENT (VISUAL CHECK OF PACKING & MARKING, RANDOM SAMPLING 10%, APPLYING OF SEAL ON ALL (500MT) JUMBO BAGS, WEIGHT CHECK, LOADING SUPERVISION, CONTAINER SEALING)
Physical Laboratory needed for EN Testing: Fire rating Testing of MDF Boards as per european standard
Middle East ISO 17025, UKAS Materials Laboratory needed for proficiency testing for cement(chemical test, loss on ignition, setting times, compressive strength), we want two samples for our labs the headquarter and our lab branch
Physical Chemistry Laboratory needed for ANSI and ASTM Particle Size Distribution Testing to detect size, shape and distribution.Cementatious products. Polyblended Grouts, Self Leveling mortars, Water Resistant Membranes. CBP is a provider of tile and stone installation systems. Products are used within setting, grouting and care. ICP/MS Elememtal Analysis. NIR composition identification
Engineering laboratory needed for security glazing, BS EN 356-2000 axe testing to BS EN 356-2000 Glass in building. Security glazing. Testing and classification of resistance against manual attack
Clinical Cytology and Histology Laboratory needed for human pathology testing in soil and water. We want a specific analysis that can provide us with a broad spectrum of results.
Physical, Mechanical Laboratory needed for physical BS EN testing to BS EN 50182: ACSR Bison Type Test 1(One)sample .
1.Verification of construction 2.Stress - Strain test 3.Tensile Breaking Strength 4.Stringing Test 5.Tests on The Alu. Wires 6.Tests on Steel Wires 7.Grease mass per unit length 8. Drop point test of grease 9.CreepTest 10. Corona/RIV Tests
Materials Laboratory needed for ASTM Testing for Facing material properties 1 Vapor Permeance ASTM E 96, Procedure A 2 Bursting Strength ASTM 774 3 Puncture Resistance ASTM C 1136 4 Tensile Strength ASTM C 1136 5 Mold Resistance ASTM C 655/ C 1338 6 Dimensional Stability ASTM D 1204 7 Emissibility ASTM E 408 8 Fire Testing ASTM E 84 9 Fire Testing BS 476
USA materials laboratory needed for biomaterials finishes testing on bio level 3 lab which can act as acoustical absorption to reduce noise build up in the lab. PVF is what is used in Clean Room 100 labs, but there is not much on biolab level 3. Is there material finishes tested for use in the biochem lab finishes, or is there a test to certify a material meets biochem level 3 labs?
Materials Laboratory needed for ASTM Testing to ASTM E1980,Standard Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque Surfaces.?? I am working on a LEED-EB:O&M certification of a project in Toronto and wish to prove that the concrete sidewalks of the building have a SRI value of greater than or equal to 29. Do you do testing on-site or do I have to send a sample it to you?
Africa Materials Laboratory needed for SANS Concrete Testing to SANS 1083S ATCC Fine aggregates for concrete Water for concrete
Asia physical laboratory needed for British Standard Testing: Abrasion Resistance testing for concrete paving blocks to BS 1338:2003
Construction Materials Laboratory needed for building materials testing before importing from China
Construction Forensics Laboratory needed for failure investigatio testing of "tile" with a blister "about the size of a nickel." The subcontractor denies using a mastic remover. Determine the nature of the solvent/substance from this small sample.
Physical Laboratory needed for SLS Testing abrasion resistance for concrete paving blocks, accordance with BS EN 1338: 2003 and SLS 1425:2011
Eastern USA and Canada Geotechnical Laboratory needed for ASTM Testing, Materials and Physical Testing: Conductivity Testing thermal and hydraulic on mix of sand and bentonite for geothermal application
Los Angeles Physical Laboratory needed for ASTM Testing to ASTM D1195/D1195M Static Plate Load Test
India Physical Materials Laboratory needed for Abrasion Resistance Testing for paving blocks Accordance with BS EN 1338:2003
India Materials Laboratory needed ASTM Testing to ASTM C1363/ASTM C518: Hot Box testing to calculate U-Value as per ASTM C1363/ASTM C518. This is to enquire and confirm the necessary details to carry out U-value test for our roofing system.
Please be informed that our standing seam is comprised of Liner profiles, Vapor Control layer, Clips, Mineral wool insulation and Kalzip profile.
Please let us know the required size of the sample for testing and please quote the cost for the test.
India materials laboratory needed for option testing of Tempered Glass by optical and light
USA railing products manufacturer needs physical laboratory for accelerated uv testing to determine how much a new powder coated hand sample will fade.
India Materials Laboratory needed for BS EN Testing of Surface Coating for concrete Crack Bridging testing to BS EN 1062 part 7
Plastics and Polymer Analytical Chemistry Laboratory needed for plastering compound testing. 1.Total Calcium content 2.Total Magnesium content 3.Loss on Ignition 4.Percentage silica 5.Polymer extraction and identification 6.Test results and its interpretation. If you could do this test please send me chargers etc.The sample i could be sent you soon.
GOVERNMENT IS REQUESTING ELECTRICAL LABORATORY FOR ASTM ELECTRICAL TESTING ON FIBERGLASS MATERIAL #ASTM-D-150 -AC LOSS CHARACTERISTICS AND PERMITTIVITY (DIELECTRIC CONSTANT) OF SOLID ELECTRICAL INSULATING MATERIALS THAT WE HAVE PROCURED FOR THEM.
ISO Physical Laboratory needed for cyclic analysis of the steel beam to column joint ( 'T' shape). No of samples 6
California Textile Laboratory needed for ASTM Testing, fabric construction testing to ASTMD1777 & ASTMD3774 (thickness and width) 10 samples machine laundered at 160F for 25 min. 5 machine dry @ Low in laundry bag for 30 min and 5 air dry. Please quote 5, 10, and 15 wash cycles performed.
Construction, Engineering, Geology Laboratory needed for geotech survey for a proposed factory site in Dammam, KSA.
Plastics Laboratory needed for Quality COntrol Testing, acrylic testing of acrylic used for the see-through tank wall of a new shark tank to be installed within a new world class aquarium under construction in the Salt Lake City area. The manufacturer is a Chinese firm providing their own quality control testing data. We would like to obtain indpendent testing results of some key material parameters to verify. We can provide samples of their acrylic. The parameters to be tested are: KEY PARAMETERS - STRENGTH, CHEMICAL RESISTANCE, CLARITY Density (D792) Modulus of Elasticity (D790) Tensile Strength (D638) Flexoral Strength (D790) Elongation at Break (D638) Impact Strength - Izod and Charpy (D256) Coefficient of Thermal Conductivity (C177) Deflection Temperature (D648) Softening Point - Venig (D1525) Coefficient of linear the
Large Construction Company needs Saskatchewan Materials Laboratory for ASTM Testing Site inspection of cementitous fireproofing testing to ASTM E605 and ASTM E736
California Materials Laboratory needed for ASTM Testing, testing sound attenuation of existing walls and ceiling assemblies in a medical office building.
West Coast USA Materials Laboratory needed for ASTM Testing: Sound Transmission Testing - E989 Flooring ISO sound testing done, but need IIC numbers for architects here in the US. E989 appears to be the test we need performed.
Materials Laboratory needed for ASTM Testing and ISO Testing of Glass Samples: 30 Glass samples to be tested for: - Compressive Strength - Thermal Cycling - Leachability - Product Consistency Test (PCT) - Vapor Hydration Test (VHT)
Rough glass samples produced by thermal waste treatment process will be provided, thus sample prep (cutting, polishing, etc.) to correct size will be required.
Materials Laboratory needed for radiation absorption tests performed on a few 8.5" x 11" sheets of zeolited coated fiber glass wallpaper.
Physical Laboratory needed for physical testing of Elastomeric bridge bearings to be tested in your laboratories according to the British Standards. I will be thankful if you would send me the cost of each test ,time of testing & the time period it will take from your side from receiving the sample tell beginning in the process of testing. The size of the first sample is 600 x 500 x 69mm & the size of the second sample is 500 x 400 x 69mm
North America Physical Laboratory needed for Thermal cycling testing: Heat exchanger construction/forestry Thermal cycle aluminum tube and fin radiator. Max temp 80 C; Min temp 18 C; ramp 3.5 to 4.5 C; pressure 10 to 12 psi; flow TBD
DUBAI PHYSICAL MATERIALS LABORATORY NEEDED FOR BS TESTING: SOUNDNESS OF CEMENT TESTING TO BS-12-1996 (42.5N) ON AUTO CLAVE & LE CHATLIER.
Materials Laboratory needed for ASTM testing of cement based construction chemicals which give concrete water impermeability character. Our products must be tested as perodically at acreditation certificated laboratories. We would like to determine their effectiveness as a waterproofer according to current standards like ASTM,CRD etc. The tests which we would like to have done are capilary water absorption, water impermeability under pressure, chloride penetration, duration against sulfate, chemical resistance against untreated concrete and then the results could be reported.
India Materials Laboratory needed for materials testing Wooden Euro pallets no.of samples- 2
USA Plastics and Polymers Laboratory needed for Hydrolytic Stability Testing of Polurethane
Physical Laboratory needed for DIN Testing: Slip resistance to determine R value for ceramic tile
MECHANICAL LABORATORY NEEDED FOR SLIPPAGE TESTING OF CABLE WALL SYSTEM THE REASON FOR THE TEST IS SLIPAGE I HAVE A VARIANT IN CABLE THICKNESS TO THIS WE FIX A CLAMP THEN PROCEED TO LOAD THE CLAMP TO THE POINT OFF SLIP
Australia analytical chemistry laboratory needed for biodegradability testing of Water based, organic liquid form release agent to prove it biodegradable and low VOC . if successful a certificate of performance will need to be supplied to us.
Large, multinational infrastructure company needs physical laboratory for for Crack Tip Opening Displacement Tests ( CTOD ).The testing should be in accordance with ASTM E 1290. Test temperature shall be -40ºC.
2.) S-5(Low sulfur steel for improved Through Thickness properties) and S-4 (Through Thickness Z- Direction Tensile Testing) in accordance with API 2W/2Y and Option 13 of EN 10225.
Material Type: Maximum Thickness 100mm Type PL1z EN 10225 S460G1+Q/+M EN 10225 S460G2+Q/+M API 2W Gr. 60Z API 2Y Gr. 60Z
Maximum Thickness 65 mm Type PL2z EN 10225 S355G7+N/+M EN 10225 S355G8+N/+M API 2W Gr. 50Z API 2Y Gr. 50Z
Construction Laboratory needed for ASTM Testing: astm d4787-08 continuity verification of liquid or sheet linings applied to concrete substrates.
Physical Laboratory needed for ASTM testing to ASTM E 408 of aluminium foil and metalized polyethelene(MPET) to ASTM E 408. Aluminum Foil isfor elaminated aluminium foil radiant barrier. Our product is to be used by construction industry intended for roofing insulation.
USA Materials Laboratory needed for DIN Testing Fire classification of construction products and building elements to DIN EN 13501-1 standards
South Africa Materials Laboratory needed for ASTM Testing Sorptivity test, Chloride conductivity test and heat of hydration test on concrete
Physical Laboratory needed for ASMT Testing to ASTM 325: High strengh bolt test ,shear test wedge test hardness test rotational tests,chemical composition,mechenical properties
Texas Materials Laboratory needed for ASTM testing of Grout as per ASTM C 307 and ASTM C 580
Hong Kong Physical Laboratory needed for BS Testing to BS EN 1338:2003 (E) standards.
Texas construction laboratory needed for LEED certification testing of Construction Building Materials to ASTM C1549: Concrete Solar Reflective Index (SRI) Value for Concrete for LEED Certification Dallas Texas SRI Value Concrete
Electrical Laboratory needed for EMI shielding effectiveness testing and surface resistivity testing of Glass fiber mat (wallpaper)
Canada environmental laboratory needed for water testing. Four samples: untreated cold water, untreated hot water, treated cold water, treated hot water: from multi-family system with copper piping. Water treated with zinc orthophosphate and sodium hydroxide to reduce copper corrosion.
Hong Kong Physical Laboratory needed for BS EN 138 Testing of concrete interlocking paver Product testing to comply with BS EN 1338 Standards
West Coast USA analytical chemistry laboratory needed for H2S testing for the removal of H2S in bunke
Puerto Rico materials laboratory needed for weathering testing for installation of a presumed hydrocarbon treatment in several wood beams.
USA Materials Laboratory needed for mechanical testing to develop a "me too" product, I have a sample of the competitors package which is made up of three components, I need to identify the components and find sourcing who can provide or replicate.
Eastern USA environmental laboratory needed for boiler and cooling tower sample testing
Physical Materials Laboratory needed for DIN Testing, IEC Testing of High pressure laminates for Industrial use . These laminates have IEC 60893 , DIN 7707 standards. We want to get them tested in a renowned labratory which has international recognition.
Eastern USA Certification Laboratory needed for ASTM Testing, Certification Testing ASTM F1561-96 Class A&B and ASTM F1988-99 Class A&B
Physical lab needed for testing waste asphalt shingle materials: 1. BTU analysis; 2. Asphalt oil content
India Materials Laboratory needed for ASTM Testing, durability tests like RCPT , Chloride bulk diffusion test to ASTM C1202 , for our Btech project on filling (ggbs) material alcofine1203 for our B.Tech project (COE,PUNE)
California Physical laboratory needed for wind tunnel testing of construction componetsMetal Panels attached to a steel frame. Would like to test to determine if they will whistle under high wind conditions
Materials Laboratory needed for All mechanical, electrical , physical, chemical properties testing to DIN 7735 , BSEN/IEC 60893 hp 2061.5
Saudi Arabia construction and building, engineering laboratory needed for vibration test of a building in which Air Conditioning Equipments are operating
West Coast Materials Laboratory needed for elemental analysis for Two samples, rock salt lumps. analysis listing trace elements.
Mechanical Product Safety labroatory needed for ANSI fall protection testing of fall protection device to OSHA standard 1926.502 and possibly ANSI standard Z359.1-2007. We are also looking for consultant/s to help with labels and manuals.
Electrical Laboratory needed for DIN 51953 Electrical conductivity testing of flooring
Middle East Construction Laboratory needed for Field and Laboratory testing of Soil, Concrete, Steel Reinforcement & other miscellaneous items for our project:
New Jersey analytical chemistry laboratory needed for CAS TESTING for Aziridine (ethylene imine) DML <100 to CAS 151-56-4
USA Physical Laboratory needed for strand relaxation test of 1000 hours relaxation test for a strand which is used in tensioned anchor construction.
Los Angeles Mechanical Certification laboratory needed to inspect Slide gate operator UL label, cannot be read he states it's too faded, needs to be inspected.
USA Physical Acoustical Laboratory needed for SRPT IIC Testing of Flooring system (adhesive and engineered hardwood flooring) on concrete slab. Measure sound and impact dampening effect of floor system. Number of samples: 1 - 4, depending on cost of testing.
Vancouver Materials Laboratory needed to test underlay sample whether it meets the standard of 63FIIC (ASTM E492)
West Coast Physical Laboratory needed for Load testing of expanded aluminum walkway products (grating)to determine max. load between supports and max.allowable deflection.
Taiwanese rubber tile manufacturer requires a Laboratory (preferably Asia) that can perform Impact Absorbing Playground Surfacing testing according to EN1177 standard.
USA Materials Laboratory needed to perform a strength test of a plastic structure that will be buried under a thin layer of concrete in a concrete floor.
India ISO Environmental Laboratory needed for ASTM aerosol concentration testing and certification of bio technology laboratory
Asia Laboratory needed to test acoustical properties of plaster board ceiling tiles.
USA EPA Environmental Laboratory needed for wastewater testing or effluent testing for surfactants presence. Concentrations levels are not as critical as the ability to distinguish and report surfactant types. Multiple surfactants are likley present within a given sample.
India ASTM Textiles Laboratory needed for Radiant panel test Smoke density static electricity as per ASTME648 ASTM662AATCC134
Materials Laboratory needed for BOCA testing fiberglass railing system as per BOCA requirements.
MIDDLE EAST ASTM MATERIALS LABORATORY NEEDED FOR TESTING AS FOLLOWS: POLYISOCYNARIDE BOARDS DENSITY 45KG/M3 TEST FOR FIRE TEST ASTM 1620 SELF EXISTINGUSING WEIGHT RETATION 90% TEST
Contract Research Organization needed for performing project in the field of adhesives, sealants, construction chemicals. Emulsion polymerization, Polyurethane dispersion (PUD).
Liberia Materials/Engineering Laboratory needed for testing road construction material and construction quality.
India Occupational Health and Hygiene Laboratory needed for performing asbestos testing on construction building materials.
Materials Laboratory needed for sealant testing of Tile adhesives, grouts, render, and other construction products.
USA Materials Laboratory needed for ASTM C1549- Testing for Solar Reflectance Index Values (SRI) for Heat Island reflectance with paving surface of synthetic grass. usually an albedo method is used
Southeast Africa Soil Engineering Laboratory needed for testing: (a) DCP (b) Test pits, maximum depth 1.5m (c) CBR testing (d) Soil indicators (e) UCS testing (f) ITS testing (g) Wet and dry durability test (h) Erosion test
CANADA METALLURGICAL LABORATORY NEEDED FOR TESTING SOLID BRASS HINGES -IN NON RUSTING AND NON CORROSIVE SPRAY TEST - PLEASE QUOTE COST.
Eastern USA Non-Destructive Metallurgical Laboratory needed to test a piece (1/2" by 1/2" triangle shape) of corrugated metal roofing material taken out from one of the roofs at West Point, NY to identify the type of materials. The description in Building Information Database indicates as "Hand-Hammered Tin Metal roof" and it was built in 1816. The purpose of testing is to determine metal characteristics such as tin, stainless steel, steel, or tin/lead.
West Ky, Southern Ill Environmental Laboratory needed for TEM / PCM testing (% asbestos on TEM) (need prices and chain of custody document)
NEC/UL/CSA ELECTRICAL LABORATORY NEEDED TO PROVIDE ELECTRICAL SAFETY CERTIFICATION / RECOGNITION FOR ELECTRIC HEAT TRACED EXTERIOR WINDOW PROTOTYPE TO BE USED IN 88 EXISTING DOUBLE AND TRIPLE GLAZED EXTERIOR WINDOW APPLICATIONS. THIS PROVISION WAS DEVELOPED TO ALLEVIATE EXCESSIVE AND UNACCEPTABLE MOISTURE CONDENSATION @ THE INTERIOR WINDOW AND GLAZED SURFACES IN THE CRITICAL CARE PATIENT AND FUTURE SURGERY ENVIRONMENTS.
HIGH R.H. MUST BE CLINICALLY MAINTAINED IN THE RANGE OF 40 % TO 60 % IN COMPLIANCE WITH VA CODE. BOTH HIGH R.H. AND THE ELIMINATION OF CONDENSATION ARE CLINICAL NECESSITY.
THIS PROTOTYPE WAS SOUGHT AS A PRACTICAL AND VERY EFFECTIVE MECHANISM TO ACHIEVE THESE CRITERIA.
USA Materials Laboratory needed for testing concrete material for water permeability, compressive strength, freezing & thawing, etc. as per CRD C48-73 - Making a concrete with our product for waterproofing concrete.
PHYSICAL LABORATORY NEEDED FOR PUF FIRE RETARDATION TESTING OF FIRE RETARDING MATERIALS
CANADA PLANT GENETIC ENGINEERING LABORATORY NEEDED FOR CONSTRUCTION OF A GENE FROM GENBANK AND TRANSFECTING THIS GENE INTO TURF GRASS (PREFERABLY VIA AGROBACTERIUM), GROWING TRANSGENIC GRASS TO MATURITY AND POSSIBLY EXPAND ITS POPULATION VIA CLONING
Geotechnical Laboratory needed for testing rocks which are used as building materials in molding,for roads..with grade of 6mm,12mm,20mm 40 mm
Environmental Toxicology Laboratory needed for mammalian toxicology testing using one of the listed protocols-need to determine the LD 50 of waste stream I am generating: Weil, Carrol S., "Tables for Convenient Calculation of Median - Effective Dose (LD50 or ED50) and Instructions for Their Use", Biometrics, September 1952. Thompson, William R., "Use of Moving Averages and Interpolation to Estimate Median - Effective Dose", Bacteria Review, November 1947. Thompson, William R. and Carrol S. Weil, "On the Construction of Tables for Moving Average Interpolation", Biometrics, March 1952. Hodge, Harold C., "The LD50 and Its Value", American Perfumer and Cosmetics, 1965.
Analytical Chemistry Laboratory needed for chemical composition testing of marble mastic
Russia Analytical Chemistry Laboratory needed for Composition Analysis & Purity Testing of Aluminum Hydroxide AlO(OH))- 1 sample
USA ASNI Mechanical/Materials Laboratory needed for Performance characteristics testing of a cast, nonporous filled polymer counter top material in accordance to Gloss ANSI Z124 , Wear and Cleanability ANSI Z124.3 and 124.6 , Stain Resistance ANSI 124.3 and Z124.6 , Izod Impact ASTM D256 Method A , Ball Impact NEMA LD 3-2000 Method 3.8 , Weatherability ASTM G155.
Kelowna, BC, Canada Environmental Laboratory needed for testing Asbestos in popcorn ceiling, which has come loose and is falling from ceiling.
Abu Dhabi, UAE Electrical Laboratory needed for Electrical Continuity test in Bored Piles
EN Materials/Mechanical Laboratory needed for testing TERRACOTTA Tiles for soluble salts, absence of blooming component, frost resistance, tensile bending strength, and color preserver in accordance to European Standard specification .
Midwest USA Mechanical Laboratory needed for nail and screw withdrawal resistance testing.
Large Fencing Manufacturer needs Metallurgical Laboratory for testing variety of Steel wires Galvanized, Aluminized and PVC Coated. These are used by us as a raw material (feed stock) into wire weaving machine to produce Chain Link Fence Fabric Rolls.
Hillsboro, OR Optical Laboratory needed to test light transmittance or solar module glass
Guinea Liberia Geotechnical Laboratory needed for testing typically CBR, compaction, shear strength, borrow materials testing
Central Africa Materials Laboratory needed to test 5 samples of Soilgates, soil, aggregate,and bitumen as per BS Standards
Hong Kong Consumer Products Safety Laboratory needed for product safety testing on release agent for concrete construction - 1 sample to be analyzed. We need to demonstrate that this product is safe for the workers and safe for the environment. We already have made this product tested in France (by CRAM organization)
USA ISO Physical Laboratory needed for moisture vapor transmission rate for a foam underlayment pad.
Asia BS EN Materials Laboratory needed for testing in accordance to BS EN 12320 Building hardware - Padlocks and padlock fittings Requirements and test methods.
Occupational Health and Hygiene Laboratory needed for testing samples for analysis for Respirable Dust, Asbestos and Silica.
California Environmental/Microbiology Laboratory needed for testing fiberglass concentration in air/house;mold
India ASHTO Laboratory needed for transportation testing to obtain certification for geo-textiles for the construction industry.
ASTM/MIL Physical Laboratory needed for testing on Welding materials, liquids as follows: testing to be done to MIL-PRF-25567E including mold growth in appendix A of MIL-PRF-25567E, ASTM D1177-07, freezing point of Aqueous Engine coolants, ASTM D92 Cleveland Open Cup flashpoint testing
Kansas City, MO or Kansas City, KS AWS, ASME Mechanical Laboratory needed for mechanical tensile and bend testing for welding qualification.
Malaysia ISO Materials Laboratory needed for EN-196, ASTM Testing, cement testing - required analysis of (compression & fluxtral test- setting time- sulfate resistance- loss on ignition) of cement
Europe Mechanical Laboratory needed for EN impact testing, EN 13964, ball impact resistance as described in the European standard EN 13964
ASTM Physical Laboratory needed for emissivity testing on powder paints as per ASTM.
USA Physical Laboratory needed for Whole window U-factor testing according to ASTM C236 and AAMA 1503
Seattle, Washington Area AASHTO Laboratory needed for concrete sampling, test cylinders and compression testing.
Acoustics/Mechanical Laboratory needed for testing noise absorption and mechanical strength to ZTV-88 or BS EN-1794, highways noise barrier.
UAE ASTM or BSI Physical Laboratory needed to check the Glass Transition Temperature of the Fiberglass Material by Differential Scanning Calorimeter.
Middle East ISO Laboratory needed for spinal construction cyclic test as per ISO 12189.
USA/Asia Materials Laboratory needed for DIN 18032- part2 testing with and without black rubber underlayment 0.032lbs/in3 for the 5.2 shock attenuation test
Australia/Hong Kong AS Materials Laboratory needed for testing to obtain certificate of AS 4992 (Australian Standard,for tile adhesive and grout) Two Samples
ASTM, AASHTO Materials Laboratory needed for evaluation of Reclaimed Asphalt Pavement, Recovery of Aged Asphalt Binder from RAP, Determination of amount and grade of Rejuvenating Agent required using Viscosity Blending Chart, Recycled Hot Mix Asphalt Design Development
USA Analytical Chemistry Laboratory needed for Flash Point testing on 4 samples of an epoxy type paint type mixture. 2 contain toluene and 2 contain xylene.
Analytical Chemistry Laboratory needed to perform testing for tribromoanisole/tribromophenol in paper (destructive testing) and on aluminum can liners.
Toronto, ON ASTM Materials Laboratory needed to assist with testing of construction waterproofing materials in accordance to ASTM C1305, C1246, C957 and other standards.
India Materials Laboratory needed for testing in accordance to ASTM or ISO for measurement of thermal conductivity and fire retardancy/ resistance of wood based panels. Please specify no of panels needed for testing.
Analytical Chemistry Laboratory needed for dry cellulose ether viscosity in accordance to ASTM.
Product Safety Laboratory needed to test a product that decreases scratches and damage to roof gutters that attaches to an extension ladder.
USA Electrical Laboratory needed for testing in accordance to CCC. 1.Marking and instructions 2.Electric construction 3.Earth leakage current 4.Electric strength 5.Ground resistance 6.Dimension of plug of direct plug-in AC power adapter 7.Disturbance voltage at Mains part 8. Radiated disturbance 9. Harmonic current
USA, Canada, UK Materials Laboratory needed for testing in accordance to Din 4102 Part 15, 16 Brandschacht for B-1 Rating of product
India ASTM Geotechnical Laboratory needed for in-situ permeability tests and Laboratory permeability tests on undisturbed samples for clay samples in accordance to ASTM D-5084.
UK ASTM MATERIALS LABORATORY NEEDED FOR ROOFTEX POLYURETHANE WATERPROOFING MEMBRANE TESTING IN ACCORDANCE TO ASTM.
Toronto, ON Physical Laboratory needed to test paint applied to a building corridor to determine whether the installed product is in accordance with specifications. ie. is the paint a primer or finish coat? how many coats? type of finish? quality of paint?
Ontario Canada Materials Laboratory needed for Solar Reflectance Index testing as per ASTM C1980. Results should be acceptable for LEED credits
USA Physical Laboratory needed for testing Polish Stone Value of coarse aggregate in accordance to ASTM, recommend the use of BS Series/doc. No BS BS 812-114: Polished Stone Value - Test Procedures and Equipment - [ Traducir esta pÃ¡gina ] Aggregate Abrasion Value Polishing Stone. ... American Society for Testing Materials (ASTM), recommend the use of BS Series/doc. No BS BS 812-114 to determine Polish Stone Values. ...
Eastern USA ASTM Laboratory needed for Triaxial compression or direct shear, unconsolidated undrained, consolidated undrained, consolidated drained,sodium sulfate soundness test ASTM C88, asbestos, total petroleum hydrocarbons, BTEX, PCB's temperature probe reading
Optical Laboratory needed for measurement the light transmission of four samples of PMMA acrylic panels in accordance to BS EN 2155-5.
Chicago, IL Toxicology Laboratory needed to test one sample for marijuana. Simple confirmation or denial of substance as controlled or not.
USA NES LABORATORY NEEDED TO TEST ONE STYLE OF AUTOMOTIVE CARPET FOR CONSTRUCTION REQUIREMENTS ONLY - NO COLOR REQUIREMENTS - USING A SPECIFIC TEST METHOD NES MOO76 SUPPLIED BY THE AUTOMOTIVE MANUFACTURER
Large Door Products Manufacturer requires UK CE/EN Laboratory to test 4" x 3" Stainless Steel Hinges manufactured to the specs laid down in the standards. The tests required are CE13 for Endurance test and Fire Rating test to BS EN 1935.
We are accredited to the CE manufacturing standard as well as ISO 9001, ISO 14001 and OHSAS 18001. Certificates attached.
We are accredited to CE marked Hinges manufacturing and certificate attached. I would appreciate if you can provide me with the following information to proceed further.
1: The scope of your accreditation?
2: Do you have facilities such as test rigs etc to carry out the tests I require?
3: An estimation of costs for testing the same hinge in three different finishes.
If you require any further information at this stage then please feel free to give me a call.
East Coast USA - DE/MD Environmental Laboratory required for testing a hard foam substance sprayed on ceiling in Municipal Police Dept.'s vehicle bay. It is believed to be a fire retardant. Need to determine if it contains asbestos.
India Materials Laboratory required for: fire rating test on masonry blocks stc rating test on masonry blocks thermal u value test on masonry blocks
ASTM LABORATORY REQUIRED FOR ASTM E 662 SMOKE DENSITY TEST AND ASTM D 635 FLAMABILITY TEST
ASTM Physical Laboratory required to test the material in SRI - 78 uder ASTM C 1549 & ASTM C 1351.
Pacific USA construction materials testing laboratory needed for metallurgical, stainless steel testing to determine if it meets the 316 stainless steel requirements
WESTCOAST USA ASTM MATERIALS LABORATORY REQUIRED FOR R- VALUE (THERMAL TRANMISSION PROPERTIES ON CONCRETE ASTM C-177
Physical Laboratory needed for Interlab comparison to be conducted on cement and require z score to be calculated.
Materials Laboratory needed for ASTM Testing of COncrete to ASTM C1602/C 1602M C114 chlorideC114 sulfateC114 alkaliesC1603 total solids
Physical Laboratory needed for acoustical testing, ASTM E492 test report from qualified acoustical test lab on hardwood flooring with the under mat for use in 2nd floor of a building. The acoustical test report must be for an open web wood truss floor / ceiling assembly. Test reports for concrete, steel, or other types of construction are not sufficient.
Montreal NETA laboratory needed for AIS Acceptance Testing: resistance test, relay synchronization and protection (including calibration and configuration) Controls and adjustments. visual inspection of elements to determine damaged goods. Verification of connexions to relays. There will be a Technical Specifications book summitted to the contractor. Isolation resistance test high and low voltage. MALT test. HI-POT test. Simulation of protection fonctions of relays. Relays sheets, including characteristics, tolerances, type of arrangements, final relay ajustements, etc. Fonctional test of elements
If such a test exists, I am looking for a laboratory that can determine the age of a cured California Forensics Laboratory needed for material age determination testing of cement/mortar sample. The material is no older than 60 years old, but an exact date is needed +/- a reasonable testing error.
USA Biophysical Laboratory needed for Medical Product Stress Testing for construction of the product and weight limitations, (weight support specs) and tox clearnace concerns
KSA Physical Laboratory needed to certify the load capacity of the tirak and its accessories in a yearly basis and inspections in 6 monthly basis.
Physical Laboratory needed for bolt testing up to 48mm - assembly (bolt,nut and washer strength).
Physical Laboratory needed for migration testing of laminate under US FDA and EU parameters.
Physical Weathering Laboratory needed for testing treat Ipe (wood) decks and have them weathered, in a lab, for a year to judge results.
Middle Eastern Physical Laboratory needed for testing cable trays and cable ladders as per IEC 61537.
India Physical Laboratory needed for NFC 33020 routine testing of insulation piercing connectors as per NFC 33020 standards. Mechanical tensile strength, electrical current carrying capacity, enviornmental testing (corrosion/water immersion test etc).
US Physical Laboratory needed for testing for ANSI IEC 61537 certification for steel cable trays, cable ladders, and channel support systems.
USA Physical Laboratory needed for ASMT D92 testing for fire point of a water-base concrete curing compound.
Canada Physical Laboratory needed for BS EN 13823 flammability testing for wood siding
Building Company needs Southeast USA, IAS, A2LA mechanical laboratory for Weld testing
MATERIALS LABORATORY NEEDED FOR MECHANICAL TESTING COMPOSITE MATERIALS, AS FLY ASH FURTHER CRUSHED IN BALL MILLS AND THAT MICRON SIZE FINE POWDER HAS TO MIX WITH DUCTILE METAL BY STIR CASTING TO STUDY THE MECHANICAL PROPERTIES OF THAT FINAL PRODUCT
Materials laboratory needed for ASTM aggregates testing ASTM C 289 Potential Reactivity Please send me a quote if possible or contact me with information listed below. Your lab must also be accredited to run the test.
Saudi Arabia physical laboratory needed for ASTM Physical properties testing FRP materials
Middle East Materials Laboratory needed for External Stone Cladding Testing, Pull-Out Test required for replaced Granite Panel fixed with 4 Nos. of S.S. Angles.
Plastics and Polymers Laboratory needed for polyurethane testing wood floor to determine what finish was used. i.e. polyurethane or moisturecure
Construction Company needs environmental laboratory for asbestos PLC point light count to see if the samples are less than 1% or are higher.
Japan environmental laboratory needed for mold testing (using air samples)in Sapporo building
India ASTM E1980 Building Materials Laboratory needed for SRI value for the chemicals coating on the terrace of building with waterproofing and insulation properties and white in color
California Metallurgical Laboratory required for testing urethane and steel structural panels
USA GLP Toxicology Laboratory required to perform AMES test - I need quote and approximate turn around time (less than 6 weeks)
South Central US Geotechnical Laboratory required to do repeated load triaxial testing of aggregated solids
ANALYTICAL CHEMISTRY LABORATORY NEEDED TO TEST A SAMPLE OF SPRAY INSULATION FOR FORMALDEHYDE.
Materials Laboratory needed to test Surface Emittance No CEN Norm Flame Spread NF EN 13501-1 Smoke Developed NF EN 13501-1 Water Vapor Transmission NF EN 12086/ NF EN 1931 Temperature/ Humidity Resistance Bleeding and Delamination NF EN ISO 11339 Pliability NF EN 13859-1 / NF EN 1109 Fungi Resistance / Ergosterol NF EN ISO 846 / NF V 18-112 Weight per unit of surface area NF EN 13859-1 Length and width NF EN 822 Thickness NF EN 823 Linear dimensions NF EN 12085 Apparent density NF EN 1602 Tensile strength parallel to faces NF EN 1608 Strength and elongation to break (roof applications) NF EN 12311-1/ NF EN 13859-1 Resistance to tearing (nail shank)NF EN 12310-1 T-peel test for flexible bonded assemblies NF EN ISO 11339 Thermal resistance (guarded hot plate) NF EN 12667 Water tightness NF EN 1928 / NF EN 13111 Dimensional stability NF EN 1
U.S. ASTM Materials Laboratory needed to test Caulks and Sealants using methods included in ASTM C834 and C920
South Africa Geology Laboratory required for borehole geological testing of mud and sand for 5 storey building.
Tucson Arizona ASTM E1980 - 01 Construction Materials Laboratory required for testing concrete pavement in place for Solar Reflective Index. Two to three seperate sites need to be tested.
Texas Fire Testing Laboratory required for Textiles Product Safety Testing to test the internal heat of a fire jacket and/or pants with and without the application of a product that retards burning potential and need results certified.
USA Local Land Development Regulations for Teton County, WY, require Building Materials Laboratory for testing "no reflective materials" it is our intention to objectively obtain the reflectivity of various siding materials. We are looking for 10 quick tests. We feel that glare may be an important test result; however, we are open to expert opinions of other test results that may objectively represent said above intentions.
NABL Materials Laboratory required for testing of physical and chemical properties of construction material
West Vancouver B.C Non-Destructive Laboratory required - I want cut a hole on the concrete roof about 2'x2'square ,Could You help me to do the nodestructive inspection and make a working scheme ? so we can work according to your scheme.
USA Preclinical Contract Research Organization required for short term biopersistence test by inhalation - it has been shown that fibers longer than 20 pm have a weighted half life less than 10 days. Related to the EU directive 97/68/EC
Materials/Analytical Chemistry Laboratory needed for product testing. Semmes Inc has developed a process of introducing nano fibers into foam products now being marketed and achieving strength increases of 5X. The tests in the block below are required to determine suitablility for a number of applications. Sample Tests Required Tests Type Size per SampleRaw Polyol 100 ml 1 D4273 - Hydroxyl Content Raw Polyol 100 ml 1 D4274 - Hydroxyl NumberRaw Polyol 100 ml 1 D4672 - Water ContentRaw Polyol 100 ml 1 D4878 - ViscosityRaw Polyol 100 ml 1 D6342 - Hydroxyl NumberPUIR Foam 2
Asia, Australia, USA, India B.S.874 PART 2:2.1 :1986,B.S. 4370 Method 10 Materials Laboratory required for testing Building Insulation Materials for Thermal Conductivity Test, Closed Cell Content
Middle East Analytical Chemistry Laboratory required to perform Oil droplet size and distribution in Water samples. Please quote your rate per sample, turnaround time for the results and collection procedure for the samples pertaining to the type of bottles and preservatives.
Hawaii Metallurgical Laboratory required to test stainless steel on the bottom of 2 elevators to verify that the grade of stainless is 304. Also test the rust forming on the bottom of the elevator wall panel and determine the cause of the rusting, chemicals, salt water...etc.
Toronto CANADA Environmental Laboratory required to test Asbestos in construction materials - Random samples from each level in a home. (3)
USA Phystical Laboratory required to do IST 80.6, Standard Test Method for Water Resistance-THe Hydrostatic Pressure Test (INDA)
Orange park Florida Acoustics Laboratory needed to test sound level before and after construction
USA Materials/Toxicology Laboratory needed for testing fiberglass duct liner material: Specific Optical Density ASTM E662; Flammability ASTM E-162; Fire Gas Toxicity Pittsburg Method; Water Repellency IST 80.6-92; Acute Inhalation Toxicity of Thermal Degradation-NYS Modified Pittsburg Protocol
USA NFPA 701 and a DIN 4102 part 1 Product Safety Testing Laboratory needed for fire testing on a poly carb mesh.
South Africa bs4408 Non Destructive Laboratory required for Gamma Ray Radiography Testing for prestressed bridge beams grouting
India STC, NRC Acoustical Testing Laboratory needed for testing sandwich panels with PPGI sheet and EPS OR GLASSWOOL filled inside. we want to test its sound reduction capacity.
USA NFPA 286 MATERIALS LABORATORY NEEDED TO TEST SURFACE BURNING CHARACTERISTICS OF BUILDING MATERIALS.
USA analytical chemistry laboratory needed for wet-chemistry, acid digestion of two mortar samples for historic preservation purposes
Australia Materials Laboratory needed for ASTM Fire Safety Testing on Insulation product. Classification in accordance with ASTM E 84
US Environmental Laboratory for Testing for Chinese Drywall (sulfur emitting drywall).
USA A2LA Materials Laboratory needed for ASTM Optical Testing for 9 armor glass windows 12 X 24 X 3 inches that need Optical Deviation (ASTM F 801-96 Referance I) Optical Distortion (ASTM F 2156-06 Referance m) and Haze Test (ASTM FD 1003 Referance K).
Southeast USA Metallurgical Laboratory needed for ASTM Tensile testing of multi-stranded wire rope cable, from a crane. Diameter is 7/8 inch.
India Materials laboratory needed for ASTM Surface Burning Testing of Extruded Polystyrene Foam Boards Thermal Insulation according to standard ASTM E 84 for surface burning characteristics of building materials
Hawaii Analytical Chemistry Laboratory needed for ASTM D4327 Testing for chlorides and sulfates below 50ppb.
Plastics Manufacturer needs Tennessee Physical Laboratory for Load testing an undergroud box for stormwater detention
Indonesia Laboratory needed for SEM and Edax of aluminum sheet to know the chemical composition on the picture
Materials Laboratory needed for ASTM testing for Insulation R VALUE / K VALUE R value of sprayable insulating materials
Plastics and Polymer, Materials Laboratory needed for quality and longevity testing on water pipeline rubber rings
Eastern USA product safety laboratory needed for UL Testing of scotch marine boiler under ul standards 726 and 795 and or a MEA Test for NYC Building DEpt.
Europe Analytical Chemistry Laboratory needed for EN 197 Chemical Characteristic of cement.
PHYSICAL LABORATORY NEEDED FOR NON-DESTRUCTIVE TESTING, INSPECTION FOR FALLOWING STEEL CONSTRUCTION: I TYPE BEAM I10/22 WITH 50 FT LONG INSTALLED BETWEEN TWO CONCRET WALL IN DISTANCE FROM FLOOR 9FT 2 INCH. THIS BEAM WILL HOLD JUST LITHS.
New Jersey Physical Laboratory needed for testing to determine RMS reading on the I.D. of a piece of carbon steel tubing, 1.000" OD x .810" ID ( .095" wall ) x 1" Long. Must be tested in 4 places on the ID /rms smoothness reading
USA A2LA Construction Manufacturer needs Materials Laboratory to test surface tension (dynes/cm) on painted panel surface.
Excavating Company needs USA geochemical laboratory for ASTM soil mineralogy testing on clay to determine if bentonite Please determine if a fat clay sample collected from Hancock Co. MS and tested for classification under the unified soil classification as CH is bentonite
Western USA Microbiology Laboratory needed for microbial identifications testing for bacteria and fungi
Research Foundation needs Eastern USA biomechanical laboratory for Cyclic testing of allografts for ACL reconstruction involving a cadaver tibia, a tibial fixation device, and various allografts. This will be a pilot study (for the specific tibial fixation device in question).
AFRICA MATERIALS LABORATORY NEEDED TO TEST CONSTRUCTION MATERIALS(WOODEN, GYPSIUM, WATER PROOFING AND TEXTILE MATERIALS TO BE USED FOR A HOTEL CONSTRUCTION AND FINISHING.
Venezuela API, ASME Metallurgical or Mechanical Laboratory required for Charpy Welding test.
JIS A 1901 Materials Laboratory needed for a quote to run Japanese Industrial Standard JIS A 1901 and time to complete test and issue a report once samples arrive.
Asia IEC Electrical Laboratory required for certificate; type test for performance and type test of construction for the kind of fuse - disconnector - switchs - range (160A & 250A & 400A AND 630 A )
Ireland Metallurgical Laboratory needed to examine solder weld on copper heating pipe.
USA Materials Laboratory needed to identify the components and ratios of a marble polishing powder. I know the 2 main components are Oxalic Acid and Aluminum Oxide but I don't know the exact ratio or if there are other components to the formula.
USA Materials Laboratory needed for NFPA 701 Flammability testing of Construction tarps Is this something that you can do and what is the turn around time? where are you located?
Japan as per Japanese Standards Occupational Health and Safety and Environmental Laboratories needed for the following testing: Indoor Air Quality (IAQ) Testing Allergens Analysis Testing Noise Exposure Testing Audiometric Testing Pulmonary Function Testing Asbestos Analysis Testing Lead Paint Analysis Testing Aldehyde Profile Testing Aromatic Hydrocarbon Profile Testing Building Investigations Biosensor Testing Environmental Monitoring Inorganic Acid Profile Testing Organic Solvent Profile Testing Solder Operations Profile Testing Chemical Contaminants Testing Toxic Metals Profile Testing Vision Screening Biomonitoring Testing Radiochemistry Testing Bioaerosol Testing Amines Testing Antimony Testing Asphalt Fumes Testing Benzene Testing Cadmium Fume Testing Cadmium Dust Testing Carbo
WestCoast USA A2LA Analytical Chemistry Laboratory needed for testing to confirm the concentration of zinc taken from a galvanizing bath.
Westcoast USA A2LA Analytical Oil Testing Laboratory needed for testing grease to confirm the physical and chemical properties.
Indonesia Metallurgical Laboratory needed for testing age of corrosion on steel structure.
British Columbia Environmental Laboratory needed for testing Vermiculite attic insulation for Asbestos.
Asia UL 1715 Fire Testing Laboratory needed for Room corner test and a. IBC Section 803.3b. UBC Section 802.1 temperature test.
USA Metallurgical Laboratory needed to analyze zinc shavings for Al,Fe,Pb,Cd and Bi to .0000 %
Mexico Analytical Chemistry Laboratory needed for testing Glass fibers solubility in saline solutions. I need the ppm of Si, Ca and Mg that are solubles saline solutions
ISO West Africa materials laboratory needed for ASTM Testing for tensile strength,relative density,specific gravity,thermal resistance,colour and corrossion resistance tests [properties] of longspan aluminum roofing materils.
Central USA Physical Laboratory needed to aide in designing and testing an enclosure to UL 1203
Textiles laboratory needed to provide a written and visual representation of the weave construction and fiber content and yarn analysis.
Delaware lab needed to test soil compaction testing at a construction site in Newark, Delaware. The soil must be capable of sustaining a loading of 2000 psi. Concrete is being poured at the site. Concrete core tests are also needed for a slab & walls of poured concrete. Please contact me ASAP with cost & turn-around time. Please contact me ASAP by telephone
American lab to test construction of solid bamboo flooring, tongue & grooved planks. Looking for the following testing: Hardness ASTM D 1037 Janka Ball Dimensional stability ASTM D 1037 Flammability: ASTM E 648 Smoke density: ASTM E 622 Compressive strength: ASTM D 3501 Abrasion resistance: ASTM D 4060 Moisture content: ASTM D 4442 Formaldehyde Emissions: ASTM E 1333
Large COnsumer Products Company needs materials lab in India for analysis of asbestos in the cement tiles used for the roofing purpose.
Materials laboratory needed for failure investigation testing of engineered wood flooring. Need to determine if adhesive failed and why, and if moisture caused.
Analytical chemistry laboratory needed for non-destructive testing of 7 braided samples size #2, roughly a meter in length to to identify braid construction, identify fiber components (i.e. PET, polypropylene, polyethylene), if Spectra present, confirm it is chain extended UHMWPE or not.
Biotechnology laboratory needed for the following:
Construction and screening of partially random (15, site specific randomization in 45 nucleotide long sequences) oligonucleotide expression libraries for specific protein-protein interactions.
Testing Requirements: 1., Oligonucleotide (~ 40-50 bases long) syntheses, and random mutagenesis at every third (defied) positions. 2., Oligonucleotide sequencing. 3., Inserting oligonucleotides into vectors and expressing into oligopeptides. 4., Expression library screening for specific protein-protein interactions (phage display or bacterial two-hybrid methods) 5., Cloning, monoclonal protein production 6., Characterization of peptide interactions (Kd, specificity)
Lab Opportunity Type: lab licensure, contract R&D,
Lab Opportunity Description: We are looking for a numbe
Biotechnology lab needed for construction and screening of partially random (15, site specific randomization in 45 nucleotide long sequences) oligonucleotide expression libraries for specific protein-protein interactions
Environmental laboratory needed for lead levels testing in dust collected from building renovations
PHYSICAL LABORATORY NEEDED FOR DIN 4102 FIRE BEHAVIOR TESTING OF BUILDING MATERIALS, PP DRANGE PIPE
Physical Laboratory needed for ANSI testing for Compression strength, Tensile strength of adhesive mortars construction materials.
Microbiology laboratory needed for water testing from a new construction site and testing for bacteria.
Physical laboratory needed for EN 12320 testing on Building hardware. Padlocks and padlock fittings. Requirements and test methods
NABL Materials laboratory needed materials testing(Building and construction materials, Road and Highways materials)for our ongoing project . For that we want rate quotation and all terms and conditions.
Toxicology laboratory needed for testing African Mahogany sawdust from construction grade lumber that is causing blistering skin lesions in those exposed to it. Suspect the lumber was treated with a toxin.
Construction laboratory needed for IAQ testing and smapling including: Formaldehyde, 50 parts per billion, Particulates (PM10) 50 micrograms per cubic meter, Total Volatile Organic Compounds 500 micrograms per cubic meter, Carbon Monoxide (CO)9 part per million and no greater than 2 parts per million above outdoor levels
Electrical laboratory needed for Electro magnetic compatibility survey testing. The survey environment includes the comms systems, microwave facilities and emissions, television and radio transmitters/repeaters, radar systems., computer equipment and accessories, traffic control devices, magnetometers, electric motors, controls, x-ray equipment, power substations, aircraft, motor vehicles, high voltage cables and power lines.
The survey will basically identify all emitting devices (with the frequency range DC to 1 Ghz being assessed) or those that may be adversely effected by the surrounding electromagnetic environment. The survey will be along sections of the Dubai Metro Light Rail Transit System)
This will be a pre-construction survey.