Contract Laboratory has received the following incoming Laboratory Testing and Scientific Research Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Labs to perform their Laboratory Testing and Scientific Research. If you need a Laboratory, please Submit a Laboratory Testing Request. If you need assistance or have questions email us or call toll free 1-855-377-6821.
19-01752
Large oil company needs Toxicology Laboratory for six pack toxicity testing needed for registration of the product with the EPA
19-01738
Oil Laboratory needed for ASTM oil treatment testing based on ASTM D6201 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation or ASTM D5500 Standard Test Method for Vehicle Evaluation of Unleaded Automotive Spark-Ignition Engine Fuel for Intake Valve Deposit Formation.
19-01671
Materials Laboratory needed for ASTM testing of pipeline coating to the following ASTM Test Standards:
ASTM D 4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers ASTM G 8 Standard Test Methods for Cathodic Disbonding of Pipeline Coatings ASTM D 543 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents ASTM G 14 Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test) ASTM D 522 Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
19-01483
Materials Laboratory needed for aging studies on polyurethane insulation used on pipelines to the following ASTM Test Methods: 1) ASTM C335, 2) ASTM D2126
3) Assembly bond shear strength at 73°F ± 4 °F (23 °C ± 2°C) un-aged and thermally aged (pipe heated to 320F (160C) for 3600hrs or heated to 338F (170C) for 1450hrs)
4) Assembly bond shear strength at 284°F ± 4 °F (140 °C ± 2°C) un-aged and thermally aged (pipe heated to 320F (160C) for 3600hrs or heated to 338F (170C) for 1450hrs)
Please note that #3 and 4 involve heating a 10 foot long assembly and then cutting out three chunks for each test and utilize hot fluid pumped through the pipe with the jacket at room temperature. So that would be atmospheric pressure.
I will need an idea about turnaround time and cost.
19-01472
Large Automotive Company needs Third-Party Laboratory for ASTM Testing to ASTM D7096 Standard Test Method for Determination of the Boiling Range Distribution of Gasoline by Wide-Bore Capillary Gas Chromatography . Please provide cost per sample.
19-01418
ISO 17025 Accredited Oil Laboratory needed that has Kinematic Viscosity accreditation within their scope of accreditation needed testing of one oil sample. The expected result is 39 cSt @ 25 deg. C. The specific Gravity of the oil is 1.07 @ 25 deg. C.
19-01414
Third-Party Laboratory needed for certified assay done on tungsten ore. Can you please send info on pricing and required time. Thank You!
19-01388
USA Microbiology Laboratory needed for microbial bacterial contamination invertigation testing on liquid lubricant made of raw materials such as propylene glycol. The finished products appears to have black molds forming on the inside surface of the container. Please send me a quote for a sample analysis.
thank you
19-01379
PRODUCT DEVELOPMENT New Technology Laboratory needed for assistance in development of a petroleum oil technology that repairs/ restores old asphalt shingles.that 100% safe, plant-based roof rejuvenating spray treatment
The idea being to restore the original petroleum oil that was in the shingles when they were first created.
19-01361
PRODUCT DEVELOPMENT Contract Research Laboratory needed for studies for the development new eco-material (hydrocarbon) using a treatment with supercritical CO2. The main goal is the extraction of different organic and metalorganic substances from a complex organic matrix.
We would like to make 3-5 tests on 50 grams samples. A reference methodology is described on EPA method 3561 (Supercritical Fluid extraction of polynuclear aromatic hydrocarbons). We would like to make short supercritical CO2 extractions (approx. 10 minutes) varying conditions (temperature and pressure), including the addition of a second solvent. We would need to get an isolated extracted material and the treated matrix. A secrecy agreement is needed for a full disclosure of the material characteristics and minor test conditions.
If this treatment proofs succes
19-01350
Oil Laboratory needed for oil testing after filtration. We would also include sample kits.
19-01320
Large Oil Company needs Materials Laboratory for Vapor pressure osmometry for molecular weight measurement of polymers
19-01307
19-01279
Materials Laboratory needed for ASTM testing of samples of Distilled coal tar as per ASTM D1078 Standard Test Method for Distillation Range of Volatile Organic Liquids.
19-01238
Contract Test Laboratory needed for Beeswax quality and testing of possible adulterants.
19-01199
Analytical Laboratory needed to conduct wax extraction from a waxed sheet of paper to determine the basis weight of the paper
19-01186
Contract Laboratory needed to characterize the refractive index of oil samples and rubber samples. I would like to do the measurement at elevated temperature (35C) for a few different wavelengths across the visible spectrum
19-01066
Oil Laboratory needed for fuel testing/ Cat 1k test on F-24 fuel for submission to DoD. Please provide quote.
19-01007
Oil Laboratory needed for petrol analysis of ULG 95 (special) -Petrol: 1. Composition Test 2. C1 to C40 hydrocarbon analysis 3. Paraffin wax content in sample 4. Residue on evaporation
19-00944
India Analytical Chemistry Laboratory needed for analysis of 10 different types of pure essential oil
19-00920
Oil Laboratory needed for bitumen extract testing of 25 bitumen samples for the following: 1. Penetration test 2. Ring and ball (softening point test) 3. Viscousity test 4. Pour point test 5. Heavy metal concentration test
19-00903
US Engineering Company needs Russia Federation Metallurgical Laboratory for field metallography and replication testing.
19-00853
Oil Laboratory needed to perform ASTM testing for a number of products and their effectiveness in sorbent performance of adsorbents for use on crude oil, other chemicals and related spills.
19-00834
Oil Laboratory needed for ASTM Lube oil testing to ASTM 7419 , Standard Test Method for Determination of Total Aromatics and Total Saturates in Lube Basestocks by High Performance Liquid Chromatography (HPLC) with Refractive Index Detection
19-00771
Large Oil Company needs Oil Laboratory with the ability to measure softening point temperature using ring and ball per ASTM E28
19-00750
Oil Laboratory needed for hydrocarbon residue testing after cleaning two medium fuel oil tanks we are having cleaned by high pressure jetting prior to use for Molasses and an organic poultry oil .
19-00747
Oil Laboratory needed for purity testing of glycerol distillate by GC/MS or LC/MS. This contains NO inorganic (it is a distillate). Please provide a quote for cost.
19-00691
Off-shore oil drilling company needs UAE Physical Laboratory for compressive testing.
19-00619
Large Chemical Company needs Contract Analytical Laboratory for ASTM Biodegradability testing of five base oils to (ASTM 5864). What is the process? How much sample is needed and cost per sample?
19-00549
Small chemical company looking for USA Oil Company for vapor pressure testing on petroleum and alcoholic fuel blends. ASTM D323 or OECD Method 104 (or both!).
19-00527
North Americal Oil Laboratory for lubricant testing to the following standards: :Vapor Pressure of Petroleum Products (Reid Method). ASTM D27834 Standard Test Method for Sulfur in Liquefied Petroleum Gases (Oxy-Hydrogen Burner or Lamp) . CEC L-07-A-955 Load-carrying capacity test for transmission lubricants FZG gear machine. IP 239 Determination of extreme pressure and anti-wear properties of lubricating fluids and greases - Four ball method (European conditions)
19-00524
Refinery needs USA Analytical Chemistry Laboratory for mercury level testing in a sample of 93% sulfuric acid.
19-00416
Oil Laboratory needed for testing sludge contaminated with crude oil for the total amount of petroleum hydrocarbon in the soil.
19-00414
Large Chemical Company needs Oil Laboratory to provide a quote for the cost per temperature to determine the following physical properties of a naphthalene based fluid, either ExxonMobil A150 or A200. 1. thermal conductivity, 2. density, 3. heat capacity, 4. viscosity, and 5. vapor pressure? I am looking to have determined the physical properties at four or more temperatures, 640 F, 600 F, 550 F, and 30 F. We are thinking of using one of the above products as a heat transfer fluid with an operating bulk temperature of 610 F. We currently use a naphthalene based oil, Sure Sol 180. We need a replacement for Sure Sol 180 as this fluid is no longer available.
19-00364
Oil Laboratory needed for Discous Oil Analysis of Machinery Fundamentals lubrication.
19-00257
Oil Laboratory needed for Research Study on the performance and emission characteristics of plastic diesel and Jatropha blend in internal combustion engine at a Density at 150°C, kg/m3,
Kinematic viscosity at 400°C,
Carbon residue % (M/M), on 10% residue,
Flash point a) Abel, °C, Min b) Pensky Martens closed cup, °C, Min,
Water content, % (v/v), Max
Ash, % by mass, Max
Carbon residue (Ramsbottom) percent by mass, Max
Total sulphur content mg/kg,
Max Pour point °C, Max a) Winter b) Summer
Total acidity (mg of KOH/gm),
Max Inorganic acidity
Cetane number, Min
Cetane index, Min
Copper strip corrosion for 3 hours at 100°C
Distillation percent (v/v) recovered: a) At 350°C, Min b) At 370°C, Min
Cold filter plugging point (CFPP), Max a) Winter b) Summer
Oxygen content, per
19-00227
Petroleum Laboratory needed for Diesel Density testing, Calorific Power testing and Lower heating value testing. .Please send us your quote
19-00108
Large Chemical Company needs materials laboratory conduct a study of the physical properties of polyurethane samples before, during, and after an oil soak, in both lubricant and diesel oil, at 140 degC.
19-00093
LONG-TERM LABORATORY PARTNER Oil Laboratory needed for a variety of ASTM, ISO, GOST and Chinese standard testing of liquefied petroleum gas , Petroleum products, gasoline, diesel fuel, others
19-00058
Oil Laboratory needed for diesel engine lubricants testing and in low emissions internal combustion engine and high performance tests with the latest API Classification. Viscosity @ 40c,ASTM D445 , ISO , Fundamentals machinery lubrication. Wear Metal , Soot , Water Content, API test , TBN , Viscosity Index , Sulphate ash , Dispersion .
19-00053
Oil Laboratory needed for fuel contamination testing of fuel used in light trucks
19-00012
Industrial Laboratory needed for lubricant testing to determine if lubricants meet the wear, load and weld requirements imposed by the relevant standards. 1. FZG Load-carrying capacity/Failure load stage (CEC L-07-A-95 | 6 min.)
2. 4-Ball wear prevention after 60 mins at 40 kg load/Mean wear scar diameter (IP 239 | 0.60 mm max)
3. 4-Ball extreme pressure properties/ Weld load (IP 239 |120 kg min.)
19-00001
Geology Laboratory needed for testing on Core Samples, Tensile strength, Poisson's Ratio, Shear Parameters
18-01909
Oil Laboratory needed for Evaporation Loss% testing at 250 C max in SAE 10W lubricant.
18-01908
Oil Laboratory needed for SAE 15W40 lubricant testing 1: High temp high shear viscosity @150 C 2: Low temp pumping viscosity, mPas -30 C max Regards
18-01898
Large Mining Company needs ISO 17025 Laboratory to analyze petroleum coke and ore samples by X-ray fluorescence (XRF) and Atomic Absorption Spectrometry for : Ni%, Fe%, SiO2%, MgO%, Al2O3%, Co% CaO% Cr2O3%.
For petroleum coke samples we need to analyze for Total Sulfur content expressed in %, Moisture %, Ash %, Volatile matter %, Burning matter %, Coke %.
18-01879
University Engineering Researcher needs Biodegradability Testing of lubricant with oil and sand to Coordinating European Council?s CEC L 33 A 93
18-01840
LONG-TERM TESTING Laboratory needed for verification of the contents of 2-3 gas samples/ a week (in 500-1000 mL Tedlar bags) via gas chromatography. The gas is created in a hydrogen reformer that creates a H2 rich gas from oxisteam reformation of methanol. The reformat gas that we produce consists of the following: H2 (37%) N2 (45%) CO (6%) CO2 (12%)
We would like to have gas samples tested (via gas chromatography) by an independent lab so as to verify results.
18-01837
Laboratory needed for OECD Biodegradation testing of synthetic ester oil sample by OECD 301 F method-I Biodegradation Test ? O2 Consumption. Please provide quote asap.
18-01784
Geology Laboratory needed for kerogen (a solid organic matter in sedimentary rocks) analysis using FTIR, TOC and NMR for the chemical and structural charcterization of kerogen and its relationship with microporosity using shale (pulverised) samples.
18-01777
India Laboratory needed for % of Gibberellic acid (mainly GA3) testing in extracted crude. The Gibberellins in Butanol from fungi .
18-01773
Oil Laboratory needed for OECD oil biodegradability testing of our oil by OECD 301F Biodegradation Test ? O2 Consumption
18-01624
Automotive Company needs Industrial Microbiology Laboratory needed for microbiological study in which the reproduction is determined on 6 different bacteria. The research study is similiar to ISO 22196 Measurement of antibacterial activity on plastics and other non-porous surfaces
18-01608
USA Third party Industrial Laboratory needed for ASME Testing of the quality of spiral wound gasket in accordance with ASME B16.20 Metallic Gaskets for Pipe Flanges
If so, please send me a quotation and hope to receive today.
18-01598
18-01403
Oil company needs Laboratory to study the vapor pressure behavior of a mixture (80% H2O, 20% CO2 and 300 ppm ethylene glycol) at various pressures between 80 kPa and 250 kPa and various temperatures between 80 and 120 degrees C. The objective is to determine if with a slight pressure increase, slight temperature decrease from current conditions can we get most of the EG to condense but not the water.
18-01390
Oil Laboratory needed for crude oil testing for the percent of vanadium in a crude oil residue
18-01320
Oil Laboratory for testing 3 diesel bottles for the following tests: Kerosene test, Sulphur test, Velocity, test Density test, Flash point test, Copprt test. and Purity test
18-01317
Oil Laboratory needed for petroleum distillate testing one and/or two type to the following two methods IP346/96 Determination of polycyclic aromatics in unused lubricating base oils and asphaltene free petroleum fractions - Dimethyl sulphoxide extraction refractive index method EN ISO 3104 Determination of kinematic viscosity and calculation of dynamic viscosity of transparent and opaque liquids Pls provide quote for each separate method
18-01302
Europe Analytical Chemistry Laboratory needed for physico-chemical propertiy testing of Epoxidated Oils and derivatives for REACH compliance.
18-01291
Oil Refinery needs USA Oil Laboratory for OEC 302 CO2 Evolution (Modified Sturm Testing) on oil. Please procide , how much sample is needed, what is the cost per sample, and what is the turn-around time?
18-01176
Oil Fields Company needs Oil Laboratory for analysis and testing for hydrocarbons
18-01118
Large Corporation needs Third-Party Laboratory for ASHRAE Testing of refrigeration oils for sealed glass tube test as per latest ASHRAE-97 test procedure. 1. Refrigeration oil -57 2. Servofriz N57 3. Servofriz 57Plus The testing has to be carried out at 200 degree cent for 14 days and observations after 14 days with R22 refrigerant. The test parameters are 1. ASHRAE 97-2007/ latest ASHRAE method. 2. All test parameters should be evaluated after 14 days of exposure at 200 degree cent. 3. Pre / Post analysis of oil for TAN, Moisture , ICP analysis . 4. Photographs of before and after exposure . 5. Percentage formation of other refrigerants after 14 days exposure at 200 degree cent. 5. Sample preparation before testing: Please insure that samples should have less than 35ppm moisture before charging refrigeration oil in seal
18-01115
Veterinary Medicine Company needs Laboratory for ASTM testing of Mineral oil to the following 7 ASTM methods: ASTMD445 - Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity), ASTM D2161 - Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity, ASTM D4052 - Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter, ASTM D156 - Standard Test Method for Saybolt Color of Petroleum Products (Saybolt Chromometer Method), ASTM D565 - Standard Test Method for Carbonizable Substances in White Mineral Oil, ASTM D1533 - Standard Test Method for Water in Insulating Liquids by Coulometric Karl Fischer Titrationm, ASTM D2269 Standard Test Method for Evaluation of White
18-01007
Energy Company needs Oil Laboratory for Saturate, Aromatic, Resin and Asphaltene SARA Analysis
18-01000
ISO 17025 Oil Laboratory needed for JIS grease testing to Japanese grease standard JIS 2220:2013, Lubricating grease
18-00994
Industrial Laboratory needed for crude oil testing including Saturate, Aromatic, Resin and Asphaltene SARA analysis, Acid number and Base Number analysis
18-00991
Oil Company needs Environmental Laboratory for water analysis to ASTM procedures
18-00940
Oil Laboratory needed for standard Saturate, Aromatic, Resin and Asphaltene (SARA) SARA Hydrocarbon analysis and other ASTM testing of petrochemicals.
18-00936
Industrial Laboratory needed for aromatic and saturated hydrocarbon testing to IP368 or ASTMD7419 (HPLC) or ASTMD2007 (LC). Details of the test methods are as below: IP368 is performed for the determination of hydrocarbon types in lubricating oil basestocks - Preparative high performance liquid chromatography method. ASTM D 7419: Determination of Total Aromatics and Total Saturates in Lube Basestocks by High Performance Liquid Chromatography (HPLC) with Refractive Index Detection ASTM D 2007: Characteristic Groups in Rubber Extender and Processing Oils and Other Petroleum-Derived Oils by the Clay-Gel Absorption Chromatographic Method (LC Technique)
18-00934
Analytical Chemistry Laboratory needed for olefin wax purity testing by US Code of Federal Regulations §172.886 Standard for Petroleum Wax
18-00897
Oil Laboratory needed for EPA and ASTM testing of tire derived oil analysis to the following Test Methods:: EPA Test Methods 3040 Dissolution Procedure for Oils, Greases, or Waxes, part of Test Methods for Evaluating Solid Waste, Physical/Chemical Methods, EPA Test Method 3050 Acid Digestion of Sediments, Sludges, and Soils, D5291,Standard Test Methods for Instrumental Determination of Carbon, Hydrogen, and Nitrogen in Petroleum Products and Lubricants
D240 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter,
D189 D1796 D3228 D287,D93 D445 D97 D4294,D5291 D482 may require also D0021FR
Carbon black (granulated) properties test: BET Surface Area Nitrogen Adsorption Number DBP oil absorption number (OAN) DBP oil absorption number (COAN) Iodine adsorption Specific gravity (SG) V
18-00863
Oil Laboratory needed for a research study to turn Methane gas from Natural Gas reserves into petro-chemicals
18-00713
Materials Laboratory needed for ASTM Testing of several waxes to the following ASTM Standards: Melting Point, Ash Content, Congealing point (ASTM D938) Drop point (ASTM D3954) Penetration (ASTM D1321) Acid value (ASTM D1386) Particle Size (ASTM D185, <106 micron, >2000 micron)
18-00688
URGENT Automotive Laboratory needed for SAE testing service of a new additive for gasoline engine according to standard SAE-1321 using gasoline as baseline and then comparing statistical report to determine wjether there is gasoline savings or not in a small 4 cilinders car. Also include quotation to determine the CO2 emissions using this new additive.
18-00680
Materials Laboratory needed for ASTM Refractive Index Testing performed on a a hydantoin glycol used as a resin cross linker used in coatings and polymers to ASTM D 1218 Standard Test Method for Refractive Index and Refractive Dispersion of Hydrocarbon Liquids
18-00653
Materials Laboratory needed for DIN Testing to the following standards: TEST NORM DROPPING POINT DIN 51801, T. 2 DROPPING POINT DIN ISO 2176 BREAKING POINT (75 G/M²) DIN EN 12593 PENETRATION DIN 51580 PENETRATION (0°C) DIN 51580 CONDENSATED WATER CLIMATE, CONTAINING SO2 (KESTERNICH) DIN 50018 KFW 0,2S SALT SPRAY TEST DIN EN ISO 9227 FLASH POINT DIN EN 22719 VISCOSITY (100°C) DIN 53015 BEHAVIOR AGAINST WATER (AT 20°C AND 40°C) DIN 51807
18-00636
Toxicology Laboratory needed for reproductive toxicity study to Category 2 OECD 414, 443, 422 of lubricant product.
18-00607
Oil Laboratory needed for ASTM substance identification testing on petroleum samples to ASTM D5292 (NMR) Aromatic Carbon Contents of Hydrocarbon Oils by High Resolution Nuclear Magnetic Resonance Spectroscopy. The petroleum samples are: Distillates (petroleum), hydrotreated heavy naphthenic having CAS sample Distillates (petroleum), hydrotreated heavy naphthenic having CAS#64742-52-5. Below is the test we would like to perform on our petroleum sample: Test Name Method Description
18-00565
Laboratory needed to do benchmark/comparison testing of patio lamp fuels. We would like to test/video a number of patio lamps simultaneously, videoing the overall burn time, assessing flame height and soot formation, and perhaps providing analysis of the fuel composition.
18-00557
Oil Laboratory needed for petrochemical testing to analyze the end product of downstream petroleum products (diesel, gasoline, LPG, Lubricants, kerosene )
18-00522
Oil Drilling Operation needs Oil Laboratory for mud chemicals (drilling fluid) quality and cementing additives quality testing:
In order to verify the cementing additives dosage & effectiveness to give us accurate measures for the slurry properties ( rheological , thickening time, compressive strength?.) by Conduct lap test for cementing formula given from actual wells data (under wellbore condition). ? Quality test for the cementing additives as per API standard 10A. Quality test for the drilling fluids chemicals as per API specification 13 A.
18-00498
Industrial Laboratory familiar with ASTM and ISO standards for measuring hydrocarbon samples needed for gas analysis to the API 617 datasheet which offers the standard composition format against which all centrifugal OEMs: As a reference, the template for the Gas Fuel Suitability tool includes the API standard list of components that the lab should measure for as applicable: We would generally prefer the lab report constituents in Mol% (as in API datasheet), along with their estimation of relative density (SG), average MW, HHV, and the sampled pressure and temperature. If the sample is raw/production gas, it would be ideal if the lab could measure and report wet and dry analyses. Dry gas analysis results can occasionally be misleading as they are not taking into account the typical fraction of water in the flow stream.
18-00495
18-00472
Oil Laboratory needed for physical properties testing of crude oil including 1-Crude oil API & Specific gravity. 2-Crude oil salt content. 3-crude oil sulfur content. 4-crude oil Bs & W(i.e Basic sediments and water/ centrifugal. 5-crude oil viscosity. 6-crude oil flash & fire points. 7-crude oil pour point. 8-H2S content detector. 9-crude oil ash point.
18-00471
Forensics Laboratory needed for identification of contaminant in SAE10W-30 oil hydraulic fluid that caused hydraulic system in a farming machine became contaminated.
18-00377
Chemical Manufacturer needs MPA Testing and OECD Biodegradability Testing of chemical as per OECD/ASTM D 2667-95(2008) Standard Test Method for Biodegradability of Alkylbenzene Sulfonates. MPA Testing is basically product content water ,glycol , surfactant . appearances of product colorless liquid , ph -7 to 8, specific .gravity -1.020
18-00357
Environmental Laboratory needed for biodegradability testing for oil spill chemical concentrate product
18-00345
Microbiology Laboratory needed for testing for Hydrocarbon utilizing microorganisms or HUM Bugs/HUB bacteria
18-00328
Oil Laboratory needed for testing 30 samples for the rheological and organic geochemical analysis on oil from oil sand.
18-00295
18-00255
Materials Laboratory needed for REACH compliant testing to the following 3 ASTM Standards
1.ASTM -D86, Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure 2.ASTM D3710 Standard Test Method for Boiling Range Distribution of Gasoline and Gasoline Fractions by Gas Chromatography 3.ASTM-6730, Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100?Metre Capillary (with Precolumn) High-Resolution Gas Chromatography
18-00231
18-00177
LONG-TERM TESTING Aerospace Laboratory needed for ASTM Jet fuel testing (Jet-A) for its lower heating value (net heat of combustion) using experimental methods. There would be roughly 15-20 samples and if possible, someone located close to southern california would be preferred.
18-00157
Oil Laboratory needed for grease testing to the following standards: - V2F grease leakage, EN-14865-2 - mechanical stability, EN-14865-2 - mechanical stability, NF F 19-502 - ability to lubricate, EN 14865-1 - R2F, NF F 19-504 - dynamic bleeding, NF T 60-189 - oxidation, NF F 19-503
18-00118
Oil Laboratory needed to conduct petroleum testing to a large number of Institute of Petrleum IP testing methods including: IP 599, IP 590, IP 577, IP 564, IP 524, IP 475, IP 447, IP 424, IP 373, IP 367, IP 243, IP 225.
18-00078
Oil Analytical Chemistry Laboratory needed for ASTM Testing of ethanol to ASTM D7347 Standard Test Method for Determination of Olefin Content in Denatured Ethanol by Supercritical Fluid Chromatography. This test method is an analytical method is therefore necessary to determine total olefins in denatured ethanol intended for spark ignition engine fuel use.
18-00062
Organic geochemical laboratory needed to analyse oil sand for its bitumen content, saturate, aromatics, resins and asphaltenes content (using SARA analysis) and heavy metals present in them.
17-02001
17-01989
ISO 17025 Automotive Laboratory needed for interlaboratory comparisons according to ISO 16232 Road vehicles Cleanliness of components of fluid circuits/ ISO 4405 Hydraulic fluid power Fluid contamination Determination of particulate contamination by the gravimetric method/ ISO 4406 Hydraulic fluid power Fluids Method for coding the level of contamination by solid particles
17-01985
Organic geochemical laboratory needed to analyse oil sand for its bitumen content, saturate, aromatics, resins and asphaltenes content (using SARA analysis) and heavy metals present in them.
17-01980
PRODUCT DEVELOPMENT Laboratory needed for pilot plant scale polymerization trials to develop new products of a reactor system of 50-100 gallons size capacity. Since the pentane addition is necessary to the polymerization, the reactor needs to be pressurized and to be in a safe environment for pentane manipulation.
17-01975
URGENT Materials Laboratory needed for ASTM Testing of mineral and steam turbine oil to the following ASTM Standards: ASTM D665 Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
ASTM D2272 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
17-01897
Large corporation needs laboratory for testing of lubricating oils for example: viscosity, ICP metals, KF Water, flash point, pour points etc..
17-01865
Oil Laboratory needed for conducting a research and stability study on Propane (LPG) to determine it's emission reduction through the use of a propane additive. Additionally looking at stability as a test also. Before and after treatment with the additive.
17-01863
Oil Laboratory needed for ASTM hydrocarbon testing of petroleum products to IP 436 / ASTM D6379 Determination of Aromatic Hydrocarbon Types in Aviation Fuels and Petroleum Distillates?High Performance Liquid Chromatography Method with Refractive Index Detection
17-01812
Large oil company needs Laboratory for OECD 301B; CEC L-103-2 or CEC L-33-A-93 biodegradability testing for lubricant/grease products. CLP certification is preferred.
17-01801
Mining company needs Geology Laboratory for core testing of 30 core samples for mines
17-01762
URGENT Large oil company needs GLP laboratory REACH testing services for the full suite testing required for a substance at the 1-100 tonne category. We are already completing the analytical substance sameness testing so just need the full suite of phys chem and other testing required under Annex VII and VIII under REACH.
17-01654
LONG-TERM TESTING Engineering company needs oil laboratory for oil testing and studies to support Master Service Agreement (MSA) qualification with a major oil company. The analysis required is
1- Chemical/Geochemical Analyses 2-:Elemental Sulfur/Sulfur Speciation Studies.
17-01513
17-01438
Refinery needs materials laboratory needed for determining Mettler melt point in wax
17-01356
Oil laboratory needed for fuel additive testing for efficacy concerning lowering of Diesel Particulate Matter and other emissions such as NOX. We would also like to have them conduct a fuel efficiency test as well to ascertain if and how much the additive is affecting the fuel consumption of Diesel.
17-01197
Research facility needed to determine the reaction kinetics for the thermal cracking of a petroleum oil
17-01157
Environmental toxicology laboratory needed for OECD testing to classify water soluble, anhydrous PAG lubricant hydraulic oil as Environmentally Acceptable Lubricants (EAL) according to 4 OECD standards: OECD 301F Ready Biodegradability OECD 201 Freshwater Alga and Cyanobacteria, Growth Inhibition Test OECD 202 Daphnia sp. Acute Immobilisation Test OECD 117 Partition Coefficient (n-octanol/water), HPLC Method
17-01146
Physical laboratory needed for SAE testing on fuel lines to SAE J2027 Standard for Protective Covers for Gasoline Fuel Line Tubing
17-01139
Laboratory needed to measure thermo-physical properties of fuel additive mixtures containing ethylene, vinyl acetate and cyclohexane. Properties to measure include: critical point determination, viscosity of mixtures, density of mixtures, vapour pressures, compressibility factor, specific heat capacity, pressure-vapour temperature in liquid (supercritical and vapour phase), Vapour-liquid equilibrium data of mixtures
17-01087
Analytical chemistry laboratory needed for hydrocarbon testing in wood chips used in wine making for mineral oil saturated hydrocarbons (MOSH) and mineral oil aromatic hydrocarbons (MOAH).
17-01073
Oil laboratory needed for analysis via 2D GC/MS (GC-GC/MS) gas chromatography with mass spectrometry of synthetic hydrocarbon oil mixture for the molecular weight of the components and to determine whether the components are (a) linear (b) methylated (c) di methylated (d) tri methylated or (e) containing a cyclic group. There should be no aromatics, no metals, no S, N, O,... just hydrocarbons that are linear, methylated, dimethylated, trimethylated, or containing a cyclic group
17-01060
LONG-TERM TESTING Large corporation needs laboratory for ASTM and ISO Testing of natural oil to the following standards: ASTM D5185 (total phosphorus content), ASTM D4629 (total nitrogen content), AOCS Official Method Cc 13i-96 (chlorophyll pigments), ISO 15304M (total fatty acid content), ISO 3961 (iodine value), ISO 6321 (slip melting point), EN ISO 2719 (flash point), UOP 779 (chloride), ISO 662 (moisture and volatile matter), AOCS Ca 3b-87 (VOC), and ISO 663 (insoluble impurities).
17-01052
Large oil company needs laboratory needed for gas analysis to determine the water content in gas. Gas water content expected to be around 2-3,5 %vol. H2S - 2-4%Vol
17-01040
Oil and petroleum laboratory needed for contamination analysis of an oil used for rust prevention on engine parts,
17-00992
Laboratory needed for EPA fuel efficiency certification testing of truck and large engine as well as emissions testing with use of a liquid organic engine surface agent. EPA certification and industry certification required proving that emissions are lowered and fuel efficiency is increased.
17-00953
University researcher needs analytical chemistry laboratory for chemical composition of diesel fuel including analysis for BTX (Benzene, Toluene, and Xylene)
17-00929
Oil and petroleum laboratory needed for moisture analysis of gasoline used as fuel.
17-00925
Oil and petroleum laboratory needed for ASTM testing of ten hydraulic oils to ASTM D3427 Air Release Properties of Hydrocarbon Oils. The viscosity range requires that they be tested at 50C.
17-00918
Oil and petroleum / microbiology laboratory needed for jet fuel (Jet A1) testing for microbial growth and presence of fungi.
17-00899
Analytical chemistry laboratory needed for castor oil testing percentage range of the following chemicals: ricinoleic acid, oleic acid, linoleic acid, stearic acid, palmitic acid and others.
17-00884
LONG-TERM TESTING Geotechnical laboratory needed for drill core testing for open thin section preparation from drill cores including EMPA analysis in open thin sections, whole rock chemistry analysis (+REE), zirkone, ortite, monazite, and apatite.
17-00870
LONG TERM TESTING Oil laboratory needed for ASTM testing of petroleum / petrochemical products to determine hydrocarbon types present in middle distillates via mass spectrometry (ASTM D2425) as well as testing for fluorine and chlorine via combustion ion chromatography (CIC) (ASTM D7359).
17-00775
Materials laboratory needed for ASTM testing of grease / lubricant for carbon residue. Reference samples as per MRC Test / ASTM D-4530, Low Carbon 0.3 %c
17-00771
Laboratory needed for research experiment for the evaluation of an agrocrop-based absorbent's effect on the flash point of oils.
17-00763
Environmental microbiology laboratory needed for OECD biodegradability testing of industrial lubricants to OECD 301B Biodegradation Test CO2 Evolution
17-00743
Automotive parts manufacturers needs laboratory for accelerated againg of test oil sa including GC-MS headspace and GC-MS direct injection (after dilution by dichloromethane) 2 test oil sa) 0 days and after 7 days heat agingb) 0 days and after 7 days heat aging and 21 days heat aging
17-00658
Petroleum analytical chemistry laboratory needed for deformulation and reformulation of liquid aliphatic hydrocarbons fuel additives.
17-00654
Oil Laboratory needed for ASTM testing of dielectric mineral oil to ASTM D 3487-09 Specification for Mineral Insulating Oil Used in Electrical Apparatus
17-00585
LONG TERM TESTING: Large corporation in India needs oil laboratory for various testing of petroleum products & chemicals samples
17-00564
Internationally recognized laboratories needed for benzene comparison study of fuel efficiency in engines A-80 & A-92 of gasoline imported from different countries for environmental and efficiency in engines.
17-00479
Environmental toxicology laboratory needed for OECD environmental fate study: biodegradation to OECD 301C / 301F method Ready Biodegradability Tests
17-00373
Oil refinery company needs analytical chemistry laboratory for silicon dioxide testing for determination of % purity (Silicon Dioxide) Sample is synthetic amorphous silica used as antiblocking agent
17-00293
Motor oil laboratory needed for JASO T903 (DFI, STI, etc.) testing of automotive oil.
17-00188
Large petroleum company needs Industrial chemistry laboratory for ASTM petrochemical testing to ASTM D8031-16 for acid number of terephthalic Acid (TA) by automatic potentiometric titration.
17-00156
LONG TERM. Oil and petroleum testing laboratory needed for ASTM testing of oil samples in the Middle East.
17-00129
17-00082
Oil Laboratory needed for Petroleum quality testing prior to export from Yemen
17-00063
LONG-TERM TESTING Oil Laboratory needed for hydrocarbon testing to quantify the amount of petroleum hydrocarbons (Semi volatile- kerosene, oil, diesel etc..) in soil and sediment samples.I
17-00001
Oil Laboratory needed for product development testing of diesel and gasoline additive combination with methanol. Previous studies showed the Binding of the emulsion proved elusive plus other problems were hard cold starts, check engine light, corrosion, swelling of fuel system seals and poor fuel mileage.
16-02424
Oil laboratory needed for hydrocarbon testing: surfactant/solvent formulation diluted in water at various concentrations to determine the surface tension as well as solvency of hydrocarbons - petroleum oil.
16-02317
Oil laboratory needed for ASTM gasoline testing for specific heat and thermal conductivity to: Specific Heat Capacity by ASTM D2766 versus temperature of gasoline sample. Thermal conductivity by ASTM D7896 versus temperature of gasoline sample.
16-02301
Ongoing opportunity to provide a transport company shipping Basis Jet A1 with Pre Discharge test and after discharge to conduct recertification test 'B '
16-02203
Renewable Energy Company needs pyro oil produced from tire pyrolysis tested for sulfur concentration.
16-02198
Large oil company needs Oil Laboratory for Quantitave diamondoid GC-MS analysis
16-02181
Large oil company needs Polymer Science Laboratory for polypropylene copolymer analysis for % ethylene content
16-02148
Large energy corporation needed materials laboratory for Corrosive Sulfur Test according to DIN 51353, Testing of insulating oils; detection of corrosive sulfur; silber strip test
16-02145
LONG-TERM TESTING Analytical Chemistry Laboratory needed for qualification testing to determine inhibitor (MeHQ) and PTZ (Phenothiazine) in acrylates by HPLC. We expect to have 2 samples ready for this test the week of 11/14-18. These first two samples are to qualify us for a major customer, and it will be ongoing work.
16-02119
Environmental laboratory needed for surface water testing of 4 acre lake displaying a very small diesel oil pollution bloom from run off surface water in the vicinity. Need lake water tested before stocking it with expensive carp.
16-02080
Laboratory needed for hazardous waste testing: Tar Fuel burn test for total nitrogen
16-02078
Oil laboratory needed for Fuel testing on a pump-grade gasoline: all tests need to be ASTM certified: Ethanol, Benzene, Total aromatics, oxygen, olefins, RON, MON, Dry Vapor Pressure Equivalent and Reid Vapor Pressure
16-02029
Laboratory needed for multiple tests on Oil Cooling System including crash, vibration, contamination, fire, oil leakage, thermal cycling, etc:
1. Temperature & latitude test as per DO 160 Section 4 Category -B3.
2. Temperature Variation test as per DO 160 D Section 5 Category-A.
3. Fluid Suceptability test as per DO 160 D Section 11 Category-F.
4. Humidity test as per DO 160 D Section 6 Category-C.
5. Fungus test as per DO 160 D Section 13 Category-F.
6. Salt Spray test as per DO 160 D Section 14 Category-S.
7. Water Proofness test as per DO 160 D Section 10 Category-S.
8. Icing test as per DO 160 D Section 24.
9. Operation shocks & crash safety test as per DO 160 D Section 7 Helicopter Category.
10. Constant Acceleration test test as per MIL-STD-810 Method 513.5.
11. Vibration test as per DO 160 D Sec
16-02018
Oil laboratory needed hydrocarbon testing with it's interaction with various solvents an process streams including analysis of hydrocarbon solutions with elemental sulfur. Also, sulfur purity tests and the ability to work with pure elemental sulfur and its interaction with various solvents and process streams.
16-01986
Laboratory needed for gas flooding-reporting on slim tube, gas injuction and flow assurance
16-01972
Oil Laboratory needed for cetane testing for additives including specific gravity density cloud point and flash point cetane number and cetane index
16-01952
Laboratory needed for ASTM Testing of aggregates used in oil pipeline operations to the following standards ASTM:Cement:ASTM C150 ? Standard specification for Portland cement Aggregates:ASTM ?294, ?295 - Standard Guide for Petrographic Examination of Aggregates for Concrete ASTM C33 - Standard Specification for Concrete Aggregates ASTM C637 -Standard Specification for Aggregates for Radiation-Shielding ConcreteWater:ASTM C1602 - Standard Specification for Mixing Water used in the Production of Hydraulic Cement Concrete.Steel wire:ASTM A82- Standard Specification for Steel Wire, Plain for Concrete ReinforcementEN 10080 ? Steel for the Reinforcement of Concrete. Weldable Reinforcing Steel. General (Option)
16-01942
Materials laboratory needed for propylene testing for the Purity of Liquid propylene
16-01864
GLP Toxicology Laboratory needed for petroleum/oil based organic pesticide testing:GLP tests in terms of Toxicology and Residue analysis.Please provide quotation
16-01861
Metropolitan New Jersey area laboratory needed for Butane Gas Testing for purity, aromatics, benzene, olefins per ASTM D2163 and sulfur per ASTM D6667-10. Two samples will be submitted each month through the winter.
16-01847
Materials laboratory needed for thermal conductivity testing of thermal paste used in computers, and we need to measure the actual thermal conductivity for the sale of goods. Currently developed several modifications to the calculated thermal grease thermal conductivity in the range of 0.7 - 6 W / (m * K).
16-01815
Large petroleum company needs materials laboratory for ASTM Testing of terephthalic acid to ASTM methods
ASTM D8031-16 ? Acid number for TA by potentiometric titration ASTM D1209-05 ? Color of clear liquids (Pt- Cobalt Scale)
Please provide
- Cost/analysis - Turnaround - Sample amount required
16-01786
Laboratory needed for Feasibility study for syn-gas production using a new catalyst, Catalytic activity of NixA1BEA and NixSiBEA. Fixed bed reactor with a fixed total gas flow run until catalyst activity is significantly reduced First test: a 2:1 molar ratio CH4 and O2 Second test: a typical LNG gas run with similar carbon ?C? to O2 molar ratio Third test (optional): a typical natural gas mixture with similar carbon ?C? to O2 molar ratio We only provide the catalyst
16-01719
Oil technology development company needs toxicology laboratory LC 50 and LD 50 testing with some controlled versions of HF acid. Essentially, the blends we want to test are compounds that control the acidity of HF and show an ambient pH value of as high as 4 or 5 in aqueous solutions.
We are interested to know if your firm can help us carry out this kind of testing to effectively prove that our controlled versions of HF are inherently safer than neat versions of HF acid.
We are looking for labs that can conduct both LD50 as well as LC50 testing for us.
16-01660
Petrographical Analysis on 10 samples of Feldspar Geochemical Analysis ICP-AES + ICP-MS on 20 samples of Clay Geochemical Analysis ICP-AES + ICP-MS on 20 samples of Kaolin
16-01643
LONG-TERM TESTING Oil Laboratory needed for long-standing motor analysis for metal and physical properties on motor oil performed every 30,000 miles.
16-01616
Fuel system company needs laboratory experienced in aggressive fuel fuel system compatibiligy for chemical analysis of sour/contaminated gasoline to detect presence of the following: - POM plastic - stainless steel - flourocarbon elastomer - flourosilicon elastomer - 90copper-10Ni brass - copper conductor - conductor insulation (Electrisola I220) - filter mesh (we can give you a raw sample and/or maybe a more helpful description) An estimate of the relative amounts of contaminants would also be helpful.
16-01593
Oil Laboratory needed for gas testing to be done on the gas sample with operating pressure 80 ? 124 Kg/cm2g & Operating temperature 152 Deg C (Temperature will become ambient due to equalization with surroundings). . Please find the brief description about the Gas sample
Brief Description about Gas Sample : The well fluid is directly coming from the wells mostly consists of Condensate, Gas & H2O at operating pressure of 124 kg/cm2g & operating temperature of 152 Deg C. This Gas sample is from the common production manifold where well fluid from all the respective wells join and send to further processing.
16-01584
Petroleum laboratory needed for Texas Department of Transportation Testing to Tex-501-C, TEST METHODS FOR VARIOUS BITUMINOUS MATERIALS - Test for water content, % by mass.
16-01576
Petroleum research & development laboratory needed for natural gas treatment research study. Our requirement is to check the efficiency of chemical for H2S Scavenging for crude natural gas. The natural gas stream contains H2S Concentration in crude natural gas is 150 PPM, The same needs to be treated by the chemical to achieve 0-5 PPM of H2S after treatment.
16-01548
Oil Laboratory involved in proficiency testing needed for petrol analysis, diesel for distillation characteristics using optidistil
16-01494
Materials laboratory needed for ASTM or IEC Dielectric Constant Testing for Quench Water, Gasoline, Steam Condensate, Hydrocarbon, and other refineries/petrochemical product.
16-01482
Large oil company needs Materials Laboratory for ASTM Testing of Polyurea Electric Motor Grease that requires the ASTM D3336, High Temperature Bearing Test.
16-01422
16-01387
Oil laboratory needed for petroleum and oil testing. Checking mixed xylene and n-Heptane for sulphur content and tetra ethyl lead content
16-01318
LONG-TERM TESTING Company seeking leading Petroleum Laboratory for Petroleum Testing Laboratory for Gas/Petrol Stations
16-01282
Radiochemistry / Nuclear Science Laboratory needed for Nuclear radiation resistance testing on stainless steel. Resistance of Integrated dose for 10 years 10^6 Gy
16-01207
Microbiology Laboratory needed for ASTM bacteria resistance testing on a lubricant according to ASTM E2275, Standard Practice for Evaluating Water-Miscible Metalworking Fluid Bioresistance and Antimicrobial Pesticide Performance.
16-01183
16-01131
India conglomerate needs industrial hygience laboratory to conduct air & water quality testfrom 4 different places. Air samples to be collected and one water sample for testing. Please give quotation for the same.
16-01093
Oil Laboratory needed for lubricant testing: Quantitative Spectrophotometric Analysis QSA and RULER (Remaining Useful Life Evaluation Routine,
16-01067
16-01027
Materials laboratory needed for ASTM D7419-13 testing Standard Test Method for Determination of Total Aromatics and Total Saturates in Lube Basestocks by High Performance Liquid Chromatography (HPLC) with Refractive Index Detection
16-00985
LONG-TERM TESTING ISO accredited Privately held, Third-party laboratory needed for petrochemical testing by standard test methods for 'ethanol mainly for fuel applications.
16-00977
Materials laboratory needed for biodegradability testing to determine the biodegradation of organic solvents, Please specify costs and timeframe.
16-00952
Large corporation needs Physical Laboratory for Need bulk sample (~1,800-lb) jaw crushing of 12 x 6 dia. consolidated wet mix material (silica-alumina matrix) to 1/2 - 1 size.
16-00941
URGENT Materials laboratory needed for physical and microbiology ASTM testing of tape bituminous wrapping tape used in petroleum pipelines Property Values Test method Tensile strength 12 N/mm2 BS 2782 Elongation 300 ASTM D 1000 Tear resistance >50 ASTM D1004 Adhesion to steel >2 ASTM D1000 Adhesion to Self >1.8 ASTM D 1000 Impact resistance >15J DIN30627 Dielectric strength >30000 total systemASTM D149 Insulation resistance2.5x1012 Ohm.cm ASTM D257 Water Absorption <0.1% ISO 62 Water permeability 0.01g/100inch2/24h ASTM F1249 Bacterial Growth - No Mic
16-00929
Shipping vessel owner needs Spain laboratory for bunkered fuel analysis ?Asphaltenes, Ash, Carbon Residue ?Density, Flashpoint ?Sulfur Content, Hydrogen Sulfide ?Microbes Contamination ?Pour Point, Stability ?Total Sediment Potential (TSP) ?Viscosity, Water Content ?ISO 8217 Bunker Fuel Testing ?H2S Testing for Bunker Fuels ?Bunker Fuel Chemical Contamination Screening ?Chlorinated Compound Contamination of Bunker Fuel
16-00888
Large oil company needs electrical laboratory for electrical compliance inspections. At our facility we use hot sticks, release hooks, and other equipment for electrical repair would need certified inspections . Our protective gear and equipment that needs required certified inspections under NEC would be involved also.
16-00871
Materials laboratory needed for ASTM and Lubrizol Testing for Test cloud point of water soluble ethoxylated product. Cloud point of a liquid detergent formulation to ASTM D2024-09 or TP-AATM-108A-a Lubrizol Test Procedure
16-00859
Laboratory needed for DOT Jerrican (2.2-gallon portable fuel container) Testing per Department of Transportation (DOT) ?Subpart M: Testing of Non-Bulk Packaging and Packages CFR / I / C / 178 ? Specification of Packages, Sections 178.603, 178.604, 178.605, 178.606, 178.608 and 178.609
16-00811
Oil Laboratory needed for sulphur testing in transformer oil to ASTM Test method D 1275 B, Corrosive Sulphur Test
16-00785
Large petrochemical company needs laboratory for measurement of the accurate density of a molten solid. The density of a molten solid (melting point of 185C) is needed between 195C and 230C. The density at 200C is approximately 1.14 gr/cc. It is estimated that the density at 210 will be ~1.13 gr/cc. The measurement ideally be good to three decimal points. Error limits on the measurement is also desired. Is the measurement even possible if the container used for the device expands at these temperatures?
16-00762
16-00712
Analytical chemistry laboratory needed for biodiesel testing. Analysis of the composition of biodiesel B5 95 % diesel 5% biodiesel
16-00696
Analytical Chemistry Laboratory needed for chemical analysis to determine composition of butyl reclaimed rubber to be able to assess the registration requirements of the EU REACH Regulation.
16-00691
Analytical chemistry laboratory needed for USP Testing of petroleum jelly to USP method standards
16-00665
India NABL Laboratory needed for natural gas testing of Calibration standard gas mixtures for natural gas analysis on gas chromatographs as per NABL accredition
16-00657
16-00637
Petroleum company needs NABL Accredited Laboratory for grease testing as per Indian Standards IS 507 : 1993 Grade 2 (https://law.resource.org/pub/in/bis/S11/is.507.1993.pdf) : 1. Glycerine content, percent by mass, MAX 2. Low temperature pumping properties 3. Water content, percent by mass, MAX 4. Corrosion preventive test, Max NABL Accredited Laboratory required.
16-00604
LONG-TERM India Laboratory needed for natural gas analysis on regular intervals as per OEM guidelines like hydrocarbons, CO2, nitrogen and contaminants in natural gas.
16-00557
Geology Laboratory needed to provide a bid for the following cor analysis : porosity and permeability analysis of 15 1x2 cores (we supply the core); two (2) of those samples will also have MICP analysis after initial P&P results; 15 thin sections from 1x2x.25 billet (supplied)
16-00528
Laboratory needed for testing ABS Rings for ASTM D5001, Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)
16-00442
Oil laboratory needed for ASTM testing of lube oil for ash, lead and water content to ASTM D874, E203, D5185
16-00386
Energy company needs laboratory for fuel testing. I have three samples (Light Ends, Solvent, and Industrial Diesel Fuel) that would require the tests the following tests: ? Appearance (physical state, color, etc.); ? Upper/lower flammability or explosive limits; ? Odor; ? Vapor pressure; ? Odor threshold; ? Vapor density; ? pH; ? Relative density; ? Melting point/freezing point; ? Solubility(ies); ? Initial boiling point and boiling range; ? Flash point; ? Evaporation rate; ? Flammability (solid, gas); ? Partition coefficient: n-octanol/water; ? Auto-ignition temperature; ? Decomposition temperature; and ? Viscosity ? Reactivity; ? Corrosivity All three samples are petroleum based.
16-00357
16-00288
Analytical laboratory needed for wide rande hydrocarbon gas chromotagraphy to determine gas composition test on the natural gas coming from gas field for composition of the hydrocarbons right up to C16, the Gross and Net Heating Values of the gas, the Molecular Weight, the compressiblity factor and the adiabatic coefficient.
16-00270
Large engineering company needs middle eastern laboratories that can determine the effectiveness of proposed asphaltene inhibitor chemicals at specified operating conditions using well samples and other well chemicals
16-00261
Petroleum company needs laboratory capable of testing Jet Fuel samples to detect the presence of additives specifically Metal Deactivator Additive and Thermal Stability Improver Additive. 8 samples
16-00186
University Scientific Researcher needs Contract Laboratory for conducting science experiments for Research Study on comparison of synthetic oil to common crude oils. Methods for the conversion of lignites, subbituminous coals and other carbonaceous feedstocks into synthetic oil are researched. The results are expected to be compared to the results of other experiments.
16-00162
Contract laboratory needed for radiation test in hydrocarbon samples. Below is some information about the samples
Propane samples ,which is a liquefied petroleum gas (LPG), will be pressurized hydrocarbons gas in liquid state. The samples are in a steel sample cylinder. Vapors samples, which is mainly consists of Methane, Ethane and a little of Propane plus, could be (or not) pressurized hydrocarbons in vapor or gas state. The samples are in a steel sample cylinder. Natural Gasoline samples, which is a liquid hydrocarbons in atmospheric pressure, are in a Boston bottles.
For Propane and 3 inlet vapor samples:
? Gross Alpha ? Gross Beta ? Radium 226 ? Radium 228 ? Strontium ? Thorium ? Uranium
For one liquid natural gasoline sample:
? VOC ? SVOC ? RCRA metals including Hg+ ? Radium 226 ? Radium 228 ? Gamma
16-00158
INDIVIDUAL Oil laboratory needed to test to car engine oil for Oil quality, Oil age, approximate usage, . I would require a written statement into age of oil, how long approximately have been used, and test of quality? This is a Land Rover genuine part. I would provide sample of brand new oil vs a test to an oil used in the car to determine if they match?
16-00109
Materials Laboratory needed that performs ASTM D6703, Standard Test Method for Automated Heithaus Titrimetry
16-00026
Asia company needs laboratory for microscopic testing of tube and shell type heat exchanger used in Liquified petroleum gas