Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Materials Laboratories to perform their Materials Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Materials laboratory that would like more information on these Materials projects, please visit Register Laboratories or call toll free 1-855-377-6821.
ASTM Testing of aluminum honeycombs to multiple ASTM standards: .ASTM C273 - Standard Test Method for Shear Properties of Sandwich Core MaterialsASTM C365 - Standard Test Method for Flatwise Compressive Properties of Sandwich CoresASTM C297 - Standard Test Method for Flatwise Tensile Strength of Sandwich ConstructionsIf you offer testing of aluminum honeycomb core, please provide a quote the three tests and for multiple honeycomb cell size.
Materials laboratory needed for IEC and ASTM Testing of insulators (several tests) : ASTM C177: Standard test method for steady-state heat flux measurements and thermal transmission properties by means of the guarded hot-plate apparatus. (We only have the similar test as per attachment.) · IEC 60383-2 (Equivalent to JIS C 3801-1:1999): Insulators for overhead lines with a nominal voltage above 1000 V - Part 2: Insulator strings and ins ...
Materials laboratory needed for NATO coatings testing of chemical agent resistant coating (CARC) to North Atlantic Treaty Organization NATO AEP 64 standard fo Performance Requirements for Paint Systems Resistant to Chemical Agents and Decontaminants, for the Protection of Land Military Equipment and 65 coded Standard, described as Performance Requirements and Test Method for Paint Systems Resistant to Chemical Warfare Agents, for new new coatin ...
Materials Laboratory needed for ASTM Testing of Processed woodcore Panel Board assemblies (using core material such as MDF / Particle Boards, Laminates, Edge Banding etc etc ).We are looking for Test Certification for ?ASTM E84-06a? for surface burning characteristics of the Finished Panel Board assemblies (where we would like for the Test to make specific reference to the actual assembled components for Wood-core Panels including core, Laminates ...
Materials Laboratory needed for ANSI Testing of Latex Coated Multipurpose Work Glove to be ANSI rated for Cut and Abrasion Resistance as demonstrated by an independent laboratory testing report (if certified to ANSI/ISEA-2016, Cut Level A2 and Abrasion Level 3). Thank you so much for your assistance in this matter.
Large company needs materials laboratory needed for accelerated aging study on thermoset material with for yellowing index and light transmitting to identify the relationship between the hours accelerated test and the years of outdoor exposure.Please, send me the costs for tests and measurements and samples dimensions.
Materials Laboratory needed for Material characterization of metal with Polymer thinfilm - Mechanical properties characterization of flat thin steel (0.1 x 5 x 30mm) - Mechanical properties characterization of bent thin steel (0.1 x 5 x 30mm) down central axis - SEM imaging and cross sectioning of of metal+polymer thin film for thinfilm measurement
Nanotechnology company needs materials laboratory for conducting studies on nanoparticles effect on the base polymers. polymer composite testing on various polymers, including PP, PE, Nylon, TPU, and others. In particular, we are interested to learn the mechanical performance (Tensile Strength, Izod Impact, Young's Modulus), Gas Permeability, Colorant Properties, Coefficient of Friction reduction, creep properties, thermal conductivity, and elect ...
LONG-TERM TESTING Packaging Laboratory needed for packaging testing of In flexible packing materials like double laminated , triple laminated & other flexible packaging material for: Flex crush resistance Water vapor transmission rate Oxygen transmission rate Optical density Lamination bond strength
Materials laboratory needed for surgical gowns testing - NFPA Standards - Standards for the use of Inhalation Anesthetics. - ASTM 1670, Standard Test Method for Resistance of Protective Clothing Materials to Synthetic Blood. - ASTM 1671 Test Method for Resistance of Protective Clothing Materials to Penetration by Bloodborne Pathogens Using Viral Penetration as a Test System. - ANSI/AAMI PB70:2012, Liquid Barrier Perfrmance and Classifi ...
Bioanalytical Laboratory needed for cell viability (MTT), cell proliferation studies (flow cytometry to characterize CD) and self-renewal studies including tagging of stromal vacular factor (SVF) cells using superparamagnetic iron oxides (SPION) and characterize the tagging using colorimetric assays such as Prussian blue staining. In addition,cell viability, studies (MTT), self-renewal studies (flow cytometry to characterize CD) and cell proli ...
LONG TERM TESTING Materials Laboratory needed for Polyamide Tube testing to prove compliance with DIN73378, DIN74324-1 and SAEJ844 Many different tests covering material mechanical properties, hydrostatic burst pressure, impact testing, moisture absorption, stiffness, cold temperature flexibility, chemical resistance, extractables, heat aging, thermal stability, artificial weathering and UV resistance.
Construction Buildings Materials company needed for ANSI or ISO adhesive testing to ANSI A118 or ISO 13007 Test adhesive tensile strength at normal temperature and water immersion *Determination of tensile adhesion strength - C *Determination of open time * Determination of slip
Materials laboratory needed for thermal conductivity testing of thermal paste used in computers, and we need to measure the actual thermal conductivity for the sale of goods. Currently developed several modifications to the calculated thermal grease thermal conductivity in the range of 0.7 - 6 W / (m * K).
Materials laboratory needed for DIN and ASTM Testing of thermal insulations foam board. Testing to To meet out the requirement of Density: DIN 53420(ASTM D 1622 Thermal conductivity :DIN 52612 OR 52616 Compressive strength :DIN 53421 (ASTM D 1621 Water vapour diffusion resistance factor: DIN 52615 Water vapour permeability : ASTM C355 Heat soaking : DIN 52328 Water absorption by submersion : DIN 53428 (28 days submersion) ASTM D 2842
Large petroleum company needs materials laboratory for ASTM Testing of terephthalic acid to ASTM methods ASTM D8031-16 ? Acid number for TA by potentiometric titration ASTM D1209-05 ? Color of clear liquids (Pt- Cobalt Scale) Please provide - Cost/analysis - Turnaround - Sample amount required
FDA compliant food laboratory needed for characterization of a natural extract (including microbiological analysis and analytical support) with the goal of filing a petition of new color additive with the FDA on 5 different batches of materials for total aerobic count, Salmonella, E. coli, yeast, and mold. We are also interested in analytical support for carbohydrates, proteins and lipids content of the same extract batches.
Medical Device Company needs medical technology laboratory for packaging/ product /development of developing a disposable medical cable assembly that will require sterilization. ABS plastic housing for connectors Silicone vs PVC for cable assembly I have questions about cost, materials, packaging and logistics.
Materials laboratory needed for ASTM Testing to measure Hiding power of coated aluminum powder to ASTM D6441,Standard Test Methods for Measuring the Hiding Power of Powder Coatings, ASTM D 3451, ASTM D 3451, Standard Guide for Testing Coating Powders and Powder Coatings
Asia Materials laboratory needed for ASTM Testing to ASTM F1671, Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System and ASTM F903, Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Liquids
Europe Materials Laboratory needed for Paint film performance tests on mild steel panels Sr No Test 1 Salt Spray Test (504 hours) 2 Humidity Resistance (504 hours) 3 Pencil hardness 4 Dry Adhesion 5 Elongation 6 Impact Resistance (direct) 7 Impact Resistance (indirect) 8 Colour Matching (Visual) 9 Colour Matching (Instrumental) 10 Metamerism Index 11 Gloss 12 Wet Adhesion 13 Chip resistance 14 Immersion Primer 15 Machinability 16 ...
Materials laboratory needed for ASTM Dielectric Testing: Dielectric Strength and Water Absorption (RT 24h) to ASTM D149, Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid. The material is 30% glass filled Peek. What test sample size and qty is needed? What is price and delivery?
Materials laboratory needed for ASTM Testing for compatiability of plasticizers to ASTM D3291 Testing (Standard Practice for Compatibility of Plasticizers...).Lab would need to accept samples of the plasticizer, and then formulate into the PVC, then perform the analysis.Approximately 10 samples.
Materials laboratory needed for paints testing for accelerated aging, hiding power, the spatter resistance, the scrub resistance, the washability, the sag resistance, the blocking resistance, the hiding change, the heat gain, the viscosity, the whiteness-yellow index, the washability, the resistance to water and the resistance to accelerated ageing.
Physical Laboratory needed for flammability pre-testing of carbon fibre samples to CS 25.853 Flammability Requirements for Aircraft Seat Cushions Appendix F, Part I, (a)(1)(ii) (i.e. 12sec vertical burn with 305mm x 70mm samples). The objective is to try 2 or 3 different materials to assist material selection and build up some confidence before testing at the lab required by our customer.
University Researcher needs materials laboratory for rheological testing of EPDM rubber compound which include viscosity vs shear rate ,dynamic modulus loss and storage moduli and tan delta. I need these data for material characterizing and extract material parameter required for rubber extrusion.
Materials laboratory needed for paints testing for accelerated aging, hiding power, the spatter resistance, the scrub resistance, the washability, the sag resistance, the blocking resistance, the hiding change, the heat gain, the viscosity, the whiteness-yellow index, the washability, the resistance to water and the resistance to accelerated ageing.
Materials Laboratory needed for biomechanical / biophysical testing for medical device burs: ¬Mechanical force of d¬evices test (compress¬ion, Torsion) Biomechanical property of dental burs is important for safety usage so test should assure torsional yield strength, torque, breaking point of dental burs moreover determine compression load force of device on rigid test block. Test apparatus should be arranged for axial force. 5.¬ ...
Medical Device Manufacturer needs medical device laboratory for sterilization validation of device sterilization process. 1.¬ ¬Sterilization method: ¬ We will supply instr¬uctions for a method ¬with step by step ins-tructions and we need¬ to get the steriliza¬tion validation ? the¬y will be autoclaved Yes it is correct but you should validate your steam sterilization parameters, temperature,duration,pressure etc. After you sterilize your ...
Materials laboratory needed for independent third party testing of laminate flooring for 1) Test for ortho phthalate plasticizers 2) Following tests with relevant ASTM test parameters (for vinyl flooring) - Stain and chemical test - Static load limit - Dimensional stability - ASTM 648 - fire test - ASTM 662 - smoke test 3) Following tests for EN / ISO parameters i) ISO 10581: Homogeneous Flooring including all the sub standards - ...
FDA cGMP Pharmaceutical analytical chemistry laboratory needed for identity testing for the following drug and excipient materials that may be used in production of clinical grade biological drug products: Pluronic F-68 1X Phosphate Buffer Saline L-Glutamine Plasmids F-17 Serum Free Media CDM4HEK293 Media Sterile water WFI Clinical 293 Suspension Cell Bank Polyethylenimine (PEI) Max. MW 25,00010X Phosphate Buffer Saline 1M Tris, pH 9. ...
Aerospace company needs materials laboratory for investigation study of delamination problem with decor laminating application.by coupled TGA-MS (Thermalgravimetric Analysis and Mass Spectrometry) to detect if offgassing occurs. We often see delamination or air bubbles popping in the interface between decor film and surface of honeycomb sandwich panel. We would like to know if there offgassing of film affecting the strength of adhesive causing ...
Larg Construction Building Materials company needs certification laboratory for ANSI Testing of tile adhesives & grout accoding to ANSI standards. FK10W Cementitious tile adhesive C1T EN 12004 GM1 Cementitious tile adhesive C2T EN 12004 FLS1000 Cementitious tile adhesive C2TES1 EN 12004 DB2000 Cementitious tile adhesive C2TE EN 12004 COLORFILL Cementitious joint grout CG2 EN 13888 Please provide pricing for quots.
LEGAL Materials laboratory needed for measuring surface of a flexible thin film material to characterize a few topographical features such as surface roughness Ra. Contact mode AFM testing in ambient; non-contact optical interferometric profilometer such as Wyko profilometer. Capable to scan 200x200 um area of sample, with resolution down to 0.5 nm roughness for smoothest materials.
Materials Laboratory needed for ASTM tensile testing to ASTM E8.,Standard Test Methods for Tension Testing of Metallic Materials. Flat tensile specimen will need to be machined according to ASTM E8 from 6061-T651 slug that is 2.75 in diameter and 8 in length. Material should meet the requirements of AMS QQ-A-225/8A. Please provide quote and delivery time. Thank you.
Materials Laboratory needed for Biodegradation testing of Plastics as per ASTM D5511, Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions and ASTM 5526, Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions etc..
Laboratory needed for ASTM tensile testing to ASTM E8.,Standard Test Methods for Tension Testing of Metallic Materials Flat tensile specimen will need to be machined according to ASTM E8 from 6061-T651 slug that is 2.75 in diameter and 8 in length. Material should meet the requirements of AMS QQ-A-225/8A. Please provide quote and delivery time. Thank you.
Materials Laboratory needed for ASTM Testing: Stress corrosion Testing on titanium according to ASTM F945. Candidate solution is the lubricant Test specimens shall be made of AMS 4911 material. The traceability of the specimen shall be done with a metal tag attached to the specimen Please provide a quote.
Third-party laboratory needed for biodegradability testing of plastic fishing baits for fishing potentially to ASTM D6691Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum as the most appropriate test.
Biomaterials laboratory needed for in-vitro surgical sealant testing 1. Burst test of surgical sealant (2-PEGs) as per ASTM F2392. 2. Gel Time test - surgical sealant (2-PEGs) 3. Swell Test - surgical sealant (2-PEGs) 5. Gel Mixing test - surgical sealant (2-PEGs)
Materials laboratory needed for rubber testing for Hexane extract, Thermal analysis (DSC, DMA, TGA) , EDX analysis (REM) of the material for heavy metals (Pb, Cr-VI, Hg, Cd), TDS-GCMS analysis of the material for softeners, Extractable matter (extration agent: n-hexane) % (Max) Tg (tan ? max) on sheet material (°C), Shore A Hardness on sheet material @ -40°C For 144 Hrs, Corrosion resistance @ 100°C for 24 Hrs.
ENvironmental laboratory needed for waste oil , soil and water testing for Radium 226/228 & other Gamma Emitters EPA 901.1 modified Waste and Oil Samples 40 samples, Fluorescent or High Intensity Discharge Lamp Preparation ANSI/NEMA: C78.LL 1256-2003/C78.LL 3-2003 Waste and Oil 10 Samples, Volatile Organic Compounds TO14A Air and Soil Gas 50 samples, Volatile Organic Compounds TO15 Air and Soil Gas 50 samples, Mercury 7471A or NIOSH 8009 ...
Automotive laboratory needed for ASTM Testing and testing to norm MS211-47 Type A2 (KIA/HIUNDAI): ASTM D792, Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement , density, relative density, specific gravity, D638 - 14 Standard Test Method for Tensile Properties of Plastics , modulus of elasticity, percent elongation, plastics, Poisson&rsquo,s Ratio, tensile properties ASTM D790, Standard Test ...
Polymer Materials laboratory needed to conduct isothermal viscosity testing of sealants and estimate working life at various temperatures. I know this cannot done by regular Brookefield viscometers. At 75 F for 2 hours at 85 F for 2 hours 100 F for two hours 120 F for 2 hours 135 F for 2 hours 150 F for 2 hours.
Marble quarry need laboratory for ANSI testing of 4 products. Quarry makes marble blocks, as raw material in order to produce high quality building materials of ready mixed mortars, tile adhesives, waterproofing materials, additives and amplifying fluids. o increase our export possibilities we have chosen the 4 following adhesives and joint grout products for testing under the ANSI standards (Standard and optional performance characteristic). ? ...
URGENT Materials laboratory needed for physical and microbiology ASTM testing of tape bituminous wrapping tape used in petroleum pipelines Property Values Test method Tensile strength 12 N/mm2 BS 2782 Elongation 300 ASTM D 1000 Tear resistance >50 ASTM D1004 Adhesion to steel >2 ASTM D1000 Adhesion to Self >1.8 ASTM D ...
Marble quarry need laboratory for ANSI testing of 4 products. Quarry makes marble blocks, as raw material in order to produce high quality building materials of ready mixed mortars, tile adhesives, waterproofing materials, additives and amplifying fluids. o increase our export possibilities we have chosen the 4 following products for testing under the ANSI standards (Standard and optional performance characteristic). ? FLS 1000, tile and marble a ...
Geology laboratory needed for geophysical testing: Size, abrasive index, moisture content, bulk density, gradation These tests need to be done on limestone and gypsum rock samples.
Materials laboratory needed for physical testing of machine part that has Sulphuric Anodization on Aluminium that require following testing. a. Insulation of the oxide coating (Disruptive voltage test) b. Sealing quality ? to measure loss of the absorptivity of the anodic oxide coating c. Continuity of oxide coating d. Light resistance test
Materials laboratory needed for ASTM boat cleaner testing on fiberglass and wood to determine it is effective and non-harmful in cleaning grease, oil, gas, scum and marine growth from boat hulls that comprise of fiberglass and wood and will not harm the surface as well. Our product is biodegradable and safe for the environment.
Russia Materials Laboratory needed for ASTM Testing for determination of iodine adsorption - ASTM D1510-13 The lab must be accredited by a single national accreditation system. The lab must be provided with equipment in accordance with the methods described in ASTM
UK cosmetics laboratory needed for full quality control testing and analyses needed for the soap industry including all raw materials (oil, water...) and finished products to to assure that the soap production is controlled and meet the EU standards and regulations
India materials laboratory needed for testing red and yellow ochre
Fittings company needs India analytical chemistry laboratory for raw material testing: Spectro (Chemical Analysis,) Micro, Mechanical,sand testing( No-Bake and Green sand) and in-coming raw materials testing etc.
Certified Materials Laboratory needed for coating testing of Three (3) mixed adhesive coating samples tested for the following: 1. Volatile Organic Compounds (VOC) content per ASTM D-3960, Section 8.2.4. (Determining Volatile Organic Content of Paints & Related Coatings) and/or SCAQMD Annex to ASTM D-3960) 2. Weight Fraction of non-volatiles (solids) per ASTM D-2369-81 (Volatile Content of Coatings). 3. Density of coating pe ...
India Materials Laboratory needed to provide a quote of rates for testing shear strength Flatwise of Fabric base Phenolic sheet as per Bureau of Indian Standard, BIS 2036 Phenol Sheets
Materials Laboratory needed for Formulation and testing of flame retardant epoxy and unsaturated polyester compositions using customer supplied additives.
ISO Materials laboratory needed for ASTM PMMA panel testing to US Standards, ISO and EN standards. ASTM E90 and E413, ASTM D-638 : tensile properties, ASTM D-790 : flexural properties, ASTM D-1003 : luminous transmittance, ASTM D-635 : burninjg of plastic, ASTM D-1929 ignition temperature. We also need to do the TL-4 inside the Report 350 (crash test safety performance). Thank you so much. Regards.
ISO 17025 Materials Laboratory needed for mechanical testing of polymers
Technology Laboratory needed for new panel design tests including theArc Resistant testsWe also need a Arc resistant test for a MCC, but for this MCC we already have the certifications for design tests. What information do you need to inform me the commercial conditions for these tests? Scope: 1 ) Design test for MV Metal Clad panel- tests According to IEEE C37.20.2-2015 6.2.1 Dielectric tests 184.108.40.206 Power frequency withstand tests 220.127.116.11 Light ...
Materials Laboratory needed for ANSI glove cut testing
USA Materials Laboratory needed for Density testing according to ASTM D1505, Standard Test Method for Density of Plastics by the Density-Gradient Technique. Please provide me the following information: 1. standard & rush turn around time & fee 2. price 3. sample amount 4. Quality System (ISO 9001, GMP, GLP?)
Food Laboratory needed to assist engineering company on project to determine the purity of a Parmesan Shredded cheese product. We are looking to determine the percentage of non-Parmesan cheese constituents in the product. These may include Cellulose, other fiber based materials, as well as other cheese species.
Jewelry manufacturer of gold or rhodium plated fashion jewelry over brass needs US Materials laboratory for material composition testing and plating thickness testing of these pieces.
Materials laboratory needed for DIN Testing of one rubber compound sample for testing: 1. DIN 53505 2. DIN 53507 3. VDA 675205 4. VDA 675303 5. VDA 675217
FDA / GMP laboratory needed for nutraceutical testing to ensure raw materials listed on the box are the only items in the finished product.
Materials Laboratory needed for ASTM Testing of Single coated tape testing for adhesion Per ASTM D3330 or PSTC 101 using 180 degree peel on polypropylene. Value to be reported in the VALLEY (lowest adhesion result) per sample. Will provide 20 samples in total, 10 now and 10 in two weeks.
Materials laboratory needed to provide a quuote for radioactivity testing on one solid sample of an epoxy coating
Geology company needs India environmental laboratory for soil and sediment testing: the stream sediment and soil samples are needed to test for multi-elemental chemical analysis in connection with preparation of certified reference materials. the samples are collected from different parts of India
Materials Laboratory needed for ASTM Testing to ASTM E-84, Standard Test Method for Surface Burning Characteristics of Building Materials
Medicinal chemistry laboratory needed for testing plant materials to determine the active ingredients for potential medicinal use or Chemical characterization of bioactive constituents. The chemical characterization of plant raw materials is to find out any major or bioactive constitutes/phytochemicals, particularly major components or bioactive components, such as flavonoids, terpenoids, phenols, saponins, coumarins, and alkaloids.
India Materials Laboratory needed for glove testing for ANSI ASTM F1790: Level 4 certification for our gloves.
Materials Laboratory needed for ASTM Testing: ASTM Closed cup flash point test (Tag or Martens, etc.) on a thin liquid material. Estimated FP is 140 F. One sample will probably suffice.
India Materials Laboratory needed for ISO Testing to ISO-105-DO2, Textiles -- Tests for colour fastness -- Part D02: Colour fastness to rubbing: Organic solvents
Materials Laboratory needed for impurities testing: the impurity, or impurities, we are removing from a crude monomer with an aluminum oxide column. H NMR does not provide a complete picture for this determination as it may possibly be an inorganic substance. How much would it cost to analyze 3 samples (neat and 2 purified) via atomic absorption? T
Materials Laboratory needed for Thermogravimetric Analysis TGA and Dilatometry on YSZ - YttrIa Stabilized Zirconia (powder) used for ceramic processing. Dilatometry (DIL 402 preferred) Thermogravimetric Analysis TGA (RT-1450C) in air in 1450C in powder form but may want pellet form.
USA Materials laboratory needed for ASTM Testing for melt point determination to ASTM D789, and dimensional stability. My sample is type 66 molybdenum disulfide-filled nylon. Could you provide me the following: 1. Pricing 2. Standard and rush turn around time, and its fee.
Eye wear company imports eyeglass frames from Italy and would like FDA GMP laboratory for certification testing that frames are made from FDA approved raw materials.
Materials Laboratory needed for biodegradability testing of lab that an antifoam to determine if it is biodegradeable.
USA Materials Laboratory needed for ASTM Testing: gel content of polyethylene samples using ASTM D2765-11, Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics (xylene or Decalin extraction, boiling solvent, sample in wire mesh cage, weight loss after 6-12 hours in boiling solvent, then vacuum oven).
Medical Device Company needs laboratory to provide quote for testing of DEHP, Latex and Phthalates on catheter. Catheter is composed from various materials: Gray Pellethane - proximal hub, Yellow - pellethane - body, Air valves - PVC, Blue & yellow Pebax - distal end, Grey Pebax - distal hub.
Microbiology laboratory needed for pyrogen testing for a medical device and components. the active ingredient is photosensitive and testing under yellow lighting would be required. None of the materials used in the device have radioactive properties
India NABL accredited laboratory needed for abs and san plastic product materials testing
North America Materials Laboratory needed for Migration test of Bisphenol A BPA and other possible constituents under 21 CFR 175.300 (d) table 1
Materials laboratory needed for Thermal Conductivity testing of DIN EN ISO 8497 for our rubber insulation
Mumbai materials laboratory needed for Low migration study of Adhesive material
University Scientific researcher needs a Middle East laboratory for conducting science experiments on fuel cells including preparation and characterization of cathode materials based oxides and thin layer of doped and undoped by chemical and electrochemical method for fuel cells, for a thesis entitled: synthesis and characterization of the doped and undoped ceria electrochemically.
URGENT Los Angeles Materials laboratory needed for material composition for a textile type material. Validation that its leather.
India materials laboratory needed to perform Tests required for Material of Gland Packing. Glass Ply OR Carbon Fibre Ply, Silicon OR Made of Ceramic Fibre. FT - IR Analysis require.
Food Laboratory needed to provide a complete quotation for heavy metal analysis in food for 4 elements (As,Cd Pb and Hg) in food materials
Materials laboratory needed for IEC electrostatic testing of polyethylene sheet to to IEC 61340-4-4, Electrostatics standard for its electrostatic properties.
Materials laboratory needed for f PROPYLENE GLYCOLtesting for appearance, PG content, moisture, density, index of refraction, acidity, distillation range, color (Pt ? Co).Please provide the price of this analysis? What the minimum amount of material and packaging is necessary for research sample?
Materials Laboratory needed that performs ASTM D6703, Standard Test Method for Automated Heithaus Titrimetry
Large piping company needs East Coast North America materials laboratory for ASTM Testing of six o-ring elastomer samples for DMA analysis to measure Glass Transition Temperature (tg values) following ASTM E 1640. Basically I need to dynamically compress the samples at starting temperature of -70 C with 1 hz frequency up to 60 C with 2 c/min heating rate.
Materials laboratory needed that is capable of running Alberta Transportation Specification B388 tests for type 3 concrete sealers
Materials Laboratory needed for ASTM Testing of hdpe/pp woven grocery bags from used hdpe/pp woven sacks including peel testing as per ASTM F88 & F2824; creep test as per ASTM F1140 & F2054;tensile testing/hermetic seal/plastic bag/shrink wrap plastic welding etc. etc.
Materials laboratory needed for Residual Gas Analysis, Raman Spectroscopy or Electron Spectroscopy for Chemical Analysis on our test parts. The sizes of the residues are typically 0.20 mm x 0.40 mm for studying the long-term effects of potential out-gassing of epoxies on the lifetime properties of modules. First trace chemical analysis provider showed that the residues are not inorganic molecules, but they were not set up to delve any deeper. ...
Materials Laboratory needed for film testing of a film structure for testing outgassing and refractory Components.
Materials Laboratory needed for microelectronics testing for collected volatile condensable materials and Total Mass Loss
Materials Laboratory needed for analysis for total chlorine content on DVB-Styrene crosslinking gel samples.
India Materials laboratory needed to provide quotation for astm e 84 testing charges of composite material
Chennai Materials Laboratory needed to measure the flank wear of a drill bit using a scanning electron microscope. Require to measure the flank wear and surface roughness of a drilled composite material
Healthcare company needs polymer laboratory for materials testing of Polytetrafluoroethylene PTFE membrane for alkalinity as per 40 CFR part 50 Appendix L
INdia materials laboratory needed for Carbon Residual Test As Per EN 723 For Brass And Copper Tubes
Materials laboratory needed for analysis for kitchen paper and wet towel, (analysis such as paraben, alcohol, eligibility for health, migration, recycle ratio...) Please provide price and turn-around time
Paint manufacturer needs Materials laboratory for IS or ASTMTesting 500 Kg jumbo bags (FIBC) to be tested for specification parameters as per the standards applicable to them.Please let us know the IS or ASTM Standards relevant to Kg jumbo bags.
Europe accredited laboratory needed with accreditation for the scope of the test method in accordance with - EN 13500 - Thermal insulation products for buildings. External thermal insulation composite systems (ETICS) based on mineral wool. Specification - Sample to be tested: Plastic - Qty: 4 Please send sample size required and turnaround time expected. For further information, please feel free to contact me. Your prompt support ...
Materials laboratory needed for Mineral Identification testing in asphalt
Materials laboratory needed for IS or ASTM Testing of bags purchased from vendor: FIBC of 500 Kg capacity made up of HDPE to be tested for Elongation and breaking strength as per the IS or ASTM Standards applicable
University researcher needs India Materials Laboratory for ASTM Testing to ASTM D445 ASTM D93-94 ASTM D5453-93 ASTM D524 ASTM D482-91 ASTM D2015-85 GAS CHROMATOGRAPHY ASTM D4052-91 AOCS CD1-25 AOCS CD3 ASTM D2500-91 ASTM D97-93 ASTM D613 Kinematic viscosity Flash Point Sulphur Carbon Residue Ash content Higher Heating Value Fatty acid profile Density Iodine value, Saponification Value Cloud point Pour Point Cetane No. ...
Large oil company needs materials laboratory to perform Soil Cleaning Test by FED-STD-791 Method, 7502. Testing to be done on an isoparrafinic solvent with flash point ~ 220F.
Southeast USA electrical laboratory needed for electrical control panel testing of installed a conveyor system (brand hytrol), with 3 electrical control panels the individual components in the panel box are all ul listed but the panel box is not we need a certificate for our final inspection that requires the box to be safe
Washington geology laboratory needed for gold testing.
Materials Laboratory needed for Oil Flashpoint Testing to ASTM d93, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Testerflash point
Materials laboratory needed for ASTM flexible laminate testing to check the WVTR and UV transmission rate to ASTM F1249. If yes, please provide the details of sample size, cost, time period..etc.
URGENT United States Materials Laboratory needed for DBL 5404 Odour Test for PPT40 Grade Resin... Please provide cost of this test ASAP.
Materials laboratory needed for ASTM Testing of laundry additives to ASTM 2274 Standard Test Method for Oxidation Stability of Distillate Fuel Oil
Manufacturer needs Consumer Products Safety Toxicology Laboratory for product safety and toxicology testing of fabric-based product.for - Cytotoxicity testing. - Sensitization testing. - Irritation or Intracutaneous Reactivity Testing - Specific testing on Urethane materials: 0 mmHg for 3s to 150 mmHg and hold for 3s for a minimum of 100,000 cycles.
Materials laboratory needed for ASTM testing of roof coating to ASTM D 6083Standard Specification for Liquid Applied Acrylic Coating Used in Roofing or to ASTM C 1549 or ASTM E 1918
Materials Laboratory needed for ASTM Testing of paint and coating to ASTM D7855, Standard Test Method for Determination of Mold Growth on Coated Building Products Designed for Interior Applications Using an Environmental Chamber and Indirect Inoculation
Materials laboratory needed for Fabric Testing required for anti radar on fabric used for camouflage nets as per MIL/BS standards.
Materials laboratory needed for ASTM Testing: Abrasive resistance test on our Abs Glass filled material as per ASTM D 1044. Please specify testing feasibility and time duration and quote to proceed further .at earliest. Immediate replay on this will be highly appreciated and looking forward
Materials Laboratory needed for ASTM E84, Standard Test Method for Surface Burning Characteristics of Building Materials Lab testing quote for Flame Spread. One sample
Materials Laboratory needed forISO footwear testing: abrasion test on footwear outer soles based on International Organization for Standardization test method 20871, which is an abrasion resistance test intended for all outer soles irrespective of material? If so, is your lab performing this test located in the United States?
India materials laboratory needed for coatings testing: 1. Polyester Fabric PU Coating Test. 2. Polyester Fabric PVC Coating Test.
Materials Laboratory needed for Thermal testing for BTU levels of bag house dust
Materials Laboratory needed for ASTM Testing of porous pipes to ASTM D638 Tensile Test, Elongations test Fluid friction coefficient test and Consistency factor (Cv) test
FDA polymer materials laboratory needed for FDA compliance testing for resinous and polymeric coatings FDA Title 21 Section 175.300. Under (a) - (2) Coatings cured by polymerization, condensation, and/or cross-linking without oxidation.
Electrical laboratory needed for materials characterization for characterizing a commercial coaxialspecialty cableliterature.Resistance, loop resistance, capacitance, inductance, voltage rating, propagation velocity, shield coverage, operating temperature range.
Packaging laboratory needed for Food Packaging testing to comply with EU food Packaging requlations. We make a water based coating that can be alternative replacement for PE, PP, PET or CPET plastic films or plastic materials. Need to have microwave heating testing and high temp ovenability ratings for coated paper board packaging products. Would prefer a Euro based lab for familiarity with EU food packaging regulations and compliance. May nee ...
Materials laboratory needed for testing mixture of rosin, beeswax and activated charcoal heated on a open flame to determine malleability and ability to be cast into shapes at low temperatures
Tyre manufacturer needs rubber testing of natural & synthetic rubbers,carbon black,silica SiO2,sulfur,zinc oxide,stearic acid,process oils,micro wax,rubber chemicals(accelerators,antidegrading materials,steel wires etc.
Physical Laboratory needed which has an accreditation for the scope of the test methods in accordance with IEC 60754-1 - Test on gases evolved during combustion of materials from cables for raw material of Silicon electric wire. I would appreciate if you could send me a ROM quote including sample size and turnaround.
Materials Contract Test Laboratory needed for ASTM / or ISO Cloud Point Testing of 9MOL(nonyl phenol exoxylate) to ISO 3015:1992 and/or ASTMD2500
EPA LEED, USGBS Environmental Laboratory needed for Formaldehyde Testing in building products. Laminate truss, urethane foam adhesive, wallboard, blown in fiberglass insulation Looking for off gas rates and comparison with accepted limits vis a vis EPA, LEED, USGBC, and the like.
Materials laboratory needed for breakdown voltage bdv testing of coatings
EU or USA Food Safety Laboratory needed for Food Contact Materials FCM safety testing of silicone baking tray to see if it meets EU and/or FDA regulation standards on FCM safety. We buy in the trays from China and want to ensure they are compliant with the regulations. They are sold to customers and used in a domestic environment.
Physical Laboratory needed to perform Salt Spray (fog) test for PTFE coated bolts (Fastener) as per ASTM B117
Materials laboratory needed for LEED and ASTM color testing of color supplied to the decorative cement market: 40 colors tested torASTM E 1980 to obtain the Solar Reflectance Index. This would be to comply with LEED 7.1 Urban Heat Island effect
USA Pharmaceutical analytical chemistry laboratory needed for USP testing on raw materials - Sodium Fluoride, USP (Identification A, Heavy Metals, Fluosicilate, & Acidity/Alkalinity) & Cetylpyridinium Chloride, USP (residual solvents).
Texas Materials Laboratory needed for Flash point testing
Materials Laboratory needed for ASTM Testing of porous pipes to ASTM D638 Tensile Test, Elongations test Fluid friction coefficient test and Consistency factor (Cv) test
Materials laboratory needed for Biodegradability testing to determine if liquid cleaning product is readily or ultimate biodegradable with percentage
North America Geology Laboratory needed for Trace level analysis of As and Pb in fine grind nepheline syenite samples and low purity quartz materials
Apparel importer needs textiles laboratory for materials testing of waist trainer corsets: Style and compositiontesting on care label is 7023 latex 100% inner lining 96% cotton 4% elastano the outer lining is made of 90% Nylon and 10% elastan both lining glue to latex
ISO 17025 Materials Laboratory needed for paint testing to VW Standard VW TL211 Table 2 section 1.3 Evaluation of effect paints in terms of differences in sparkling and graininess per VW 5019 & 1.4. Structure measurement system: wave-scan plus?
Plastics Materials Laboratory needed for Polytetrafluoroethylene PTFE Testing of PTFE UV transmittance in the 250 - 260 nm range Objective: To establish the % transmittance of a PTFE sample of : 1) 0.50 mm thick; Sample size = 1. 2) 0.30 mm thick; Sample size = 1. 3) 0.10 mm thick; Sample size = 1. Deliverable: A 1-to-2 page report in electronic format. The report should include methods and results. The results to be presented in a graph ...
USA Materials Laboratory needed for ASTM Testing of Adhesion of Solid Film Lubricants to MCL F-23 and ASTM D2510-94
Analytical Chemistry Laboratory needed for Boron materials Testing with a purity in the range of 99% (1% are impurities, 99% is amorphous boron). On such material the testing laboratory should verify the actual purity percentage and the chemical composition of the impurities; for each impurity the result should include the amount found. A typical output would be a table including all impurities and, for each item, the quantity found in respect to ...
Materials Laboratory needed for Constituent components testing of oil product generated from pyrolysis of scrap tires. Need to know all components and percentage by weight or volume.
Materials Laboratory needed for ASTM Testing of Erucamide slip counts in polyethylene pellets to ASTM D6953, Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC) or other test methods
University Researchers need Asia sensory laboratory for slow release fragrance technology testing for markets in Asia.
ISO 17025 or FDA GLP Accredited Test institute needed for catheter and catheter accessory biocompatiability testing of these materials according to related standards to Test Standard: 10993-1. We will focus on products which will stay more than 30 days in body. 2. nd product: Implantable Gel material Please give me price and make me informed about the procedure and accreditation status
University Researcher needs India materials laboratory for NiTi thin films of thickness 300 nm on silicon wafer size 1 cm x 1 cm. I need to characterize these samples using TEM. Please send the quotation.
Materials laboratory needed for OECD biodegradability testing of aluminum complex greases to OECD 201-204, OECD 107 or 117, and OECD 301B. Please include pricing.
Materials laboratory needed for tape certification testing to a specific military requirement. A-A-59341, COMMERCIAL ITEM DESCRIPTION: TAPE, TWO SIDE PRESSURE SENSITIVE ADHESIVE, FLEXIBLE FOAM BASE (FOR USE WITH EXPLOSIVES) (29-SEP-1998) [SUPERSEDING MIL-T-60394A]., This CID covers the general requirements for a double coated flexible foam pressure sensitive adhesive tape in roll form wound on a core with a release liner. The tape shall consist ...
United Arab Emirates Materials Laboratoryneeded for ASTM Testing: ASTM G180 test for Corrosion inhibiting admixtures for steel in concrete by polarization resistance in cementitious slurries.
POLYMER LABORATORY NEEDED FOR SAE AND ASTM TESTING OF RUBBER MATS TO SAE J1400, Laboratory Measurement of the Airborne Sound Barrier Performance of Flat Materials and Assemblies and ASTM2611
India materials laboratory needed for aluminum foil testing: Water Vapour Transmission Rate Testing for Aluminium Foil (20-25 microns).
Materials Laboratory needed for ASTM LEAP test as per ASTM standard ASTM D6499-12 (Inhibition ELISA.) to certify the product is latex free.
Manufacturer a counter top material with recycled window glass and an epoxy resin binder needs physical laboratory for NSF / ANSI / ASTM Physical Properties Testing Food Safety:NSF/ANSI 51 compressive strength, tested to ASTM C39 Absorption, tested to ASTM c-97-02 Sctratch Resistance/Mohs Hardness Modulus of Rupture, tested to ASTM c-99 Radon Emissions, compared to EPA-402-r-92-004 PH Miscibility(in water) Density Bending Stress Coeffi ...
Physical laboratory needed for materials testing : 1 Min reflective index wavelength range 250 to 400 nm 60% 2 NIR reflectance ISC 220 ISO 7724 Wavelength - 680 nm ?10% 3 NIR reflectance ISC 278 ISO 7724 Wavelength - 680 nm ?14% 4 NIR reflectance ISC 220 ISO 7724 750 nm to 1200 nm ( 45 +/- 10)% 5 NIR reflectance ISC 278 ISO 7724 750 nm to 1200 nm ( 45 +/- 10)% 6 NIR reflectance ISC 386 ISO 7724 750 nm to 1200 nm ( 40 +/- 10)% 7 NIR refl ...
India NABL accredited laboratory needed for partial discharge testing
United Arab Emirates Materials Laboratory needed to test our plastic product Polypropylene granules for the following Composition *Appearance *Density *Melting point/Range *Melt Flow Rate *Ignition Temperature *Hazardous Status *Solubility *Molecular weight distribution
Materials Laboratory needed for certification testing of PIR Rigid cold insulation, PIR (Polyisocynurate) foam segments are high-quality insulating materials with excellent properties and are supplied in pipe sections and slabs. Other types available on request. Standard densities are 50 (PIR), other densities are also available. PIR are used extensively on equipment and piping operating at lower temperatures in power stations, marine vesse ...
Materials Laboratory needed for required Filter Testing (Directly from US Code of Federal Regulators, 40 CFR Part 50 Appendix L,Reference Method for the Determination of Fine Particulate Matter as PM2.5 in the Atmosphere ) 6.5 Filter thickness. 30 to 50 µm. 6.6 Maximum pressure drop (clean filter). 30 cm H2O column @ 16.67 L/min clean air flow. 6.7 Maximum moisture pickup. Not more than 10 µg weight increase after 24-hour exposure to air o ...
Los Angeles area materials laboratory needed for ASTM Testing of toy building kits
Mumbai India materials laboratory needed for quality control testing of prism from different vendors. Would like to quantify the quality of the prisms in terms of the quality in material and its reflective properties.
Materials Laboratory needed for Cone calorimetry studies
India Materials Laboratory needed for materials analysis of u-pvc,c-pvc,pvc pipe solvent cement solution.
FDA GMP Laboratory needed for FTIR-PAS for our GMP pharmaceutical raw materials testing of three different GMP raw materials that require this test
Materials laboratory needed for ASTM Testing: Solar Reflective Index(SRI) - ASTM E 1980,ASTM C 1549, THERMAL EMITTANCE -ASTM C 1371
California Materials laboratory needed for ASTM rheology Testing to determine levels of cure in samples of liquid silicone rubber to ASTM D6601-12, Standard Test Method for Rubber Properties?Measurement of Cure and After-Cure Dynamic Properties Using a Rotorless Shear Rheometer
Materials Laboratory needed for ASTM Testing: Mullen burst test on rubber according to ASTM D751, Standard Test Methods for Coated Fabrics
USA materials laboratory needed forGWP testing on a new HVAC/R refrigerant
Materials Laboratory needed for Ultra Violet testing of panels used for contact staining for rubber per ASTM D 925
Company needs Materials laboratory nfor Deformulation testing of a nail polish to identify Type pf polymer used to form a layer on the nail.
FDA GMP Analytical Chemistry Laboratory needed for raw materials testing of 16 ingredients that we need to test to verify that each component meets the specifications for identity, purity, strength and composition according to FDA Current Good Manufacturing Practices (CGMP): L-Glycine FCC L-Lysine L-Arginine Mono HCL L-Ornithine Mono HCL Hydrolyzed Bovine Collagen Glucosamine HCL Chondroitin Sulfate Sodium Boron Citrate 5% Magnesium Citrate Calc ...
India materials laboratory needed for specialty adhesive testing of adhesive which is used in pvc wire.
Large Medical Device Manufacturer needs materials laboratory for Haze and transmittance testing on a flexible polymer Sample size < 20
Asia materials laboratory needed for Tensile strength and water resistance testing of crab shells bioplastics
Advanced Materials Laboratory needed for BSEN 62561 testing for lightning protection materials Thank you very much.
India or United Arab Emirates FDA and ISO Materials Laboratory needed for xenon arc exposure testing of polyester film and polyester chip & film . The xenon arc exposure test of our UV polyester film for 1000hr.
Materials laboratory needed that can test ASTM E299 on petroleum oil. The lab needs to be able to test for the lowest range 0-40ug.
Materials Laboratory needed for polymer testing with MFR, MVR
Materials laboratory needed for leachable heavy metals testing in a ceramix matrix to EPA TCLP 1311 submethod SW-846 EPA 6010/7470 . Must have ability and track record of performing the EPA Test Method.
Middle East Materials Laboratory needed for Gel Permeation Chromatography for HDPE Material GPC Testing
Medical Device Materials Laboratory needed for ASTM Condom Testing to ASTM D7661 - 10 Condom Compatibility Test
Materials Laboratory needed for Physical Testing of Chromadek faced, EPS filled, sandwich panels. Load testing Strength testing Air/water permeability Fire resistance Acoustic behavior and more to SANS 54509:2014 / EN 14509: 2013
USA Materials Laboratory needed for ANSI certification accreditation testing for reflective tapes to ANSI 107-2004 High-Visibility Clothing Standards
Materials Laboratory needed for Synthesis of candidate catalysts and verification of activity in lab validation tests. Able to handle lpg olefin monomers. Calcination at 250-700 deg C. Catalyst activation with Lewis acids. Conduct small scale batch pplymerization reaction to verify catalyst suitability. Analyze by GC but more preferably by C13 NMR.
Materials Laboratory needed for ASTM outgassing testing to ASTM E595, ASTM E595 - 15 Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
URGENT: MANUFACTURER OF TRACTOR PARTS NEEDS MATERIALS TEST OF PPU & NYLONE ( SOLID IN WEIGHT)
USA Materials Laboratory needed for ASTM Testing ASTM D2137-11 brittle point determination done on EPDM and TPO samples, as our machine currently broke down. I would like a quote for 1 sample, but I'll likely have between 5-10 samples for testing.
Road construction company needs India environmental laboratory for black trap stone aggregate testing
USA Materials Laboratory needed for Intermittent testing of 3 foam sample hardness over 30,60,90,120, and 150 wash cycles. Machine wash warm, tumble dry low.Wash & Dry Equipment & Durometer to test foam hardness changes
Manufacturer of reflective tape needs materials laboratory for ANSI 104-2007 certification testing
Materials Laboratory needed for ASTM Testing: Test various tape skus against ASTM D5486-6 Standard Specification for Pressure-Sensitive Tape for Packaging, Box Closure, and Sealing and masking tape against ASTM D6123-97 Standard Specification for Pressure-Sensitive Tape for Light-Duty Packaging and General Purpose Masking
Materials Laboratory needed for Anti-Carbonization properties testing of Deep Penetrating Sealer
India Materials Laboratory needed for ASTM Testing to ASTM C177, Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
Europe or USA Materials Laboratory needed for research study for Removing Unwanted VOC's through vacuum stripping. Testing vacuum stripping under different conditions to optimise removal of VOC's in a recycled polymer compound
Asia Toxicology Laboratory enviromental toxicology testing for CLP and REACH classification of hazardous materials to Chemical, Labeling and Packaging (CLP) for EU REACH for hazards to GHS requirements for EU Safety Data Sheets
Materials Laboratory needed for ASTM Testing: Thermal Emittance ASTM C 1371 and Solar Reflectance ASTM C 1549. I need information of the price for each test and the time it will take to make the test. And of course the specification of the sample you will be needing to test.
Physical laboratory needed for materials testing of lamination product for: Tensile & Elongation Tear Strength Surface Receptivity & Adhesion (WET & DRY) Ageing Low Temp. Flex Flex Cracking Porosity Oil Resistance Variation in Weight Weft Distortion Surface Blocking PU Weld Strength PU Hydrolysis Ozone Resistance UV Resistance Document reference MSC70-23a1-6
USA Materials laboratory needed for automotive standards testing of 3 different film materials on an automotive standard (MS 373- 12). Gasoline Non-leaded gasoline or isooctane :Toluene = 1 : 1 (by volume) 1 hr Brake Fluid Shall conform to MS 517- 06 1 hr Engine Oil HMC GENUINE OIL 10W 30 or equivalent 1 hr Antifreeze HMC GENUINE LONG LIFE COOLANT or equivalent 1 hr Thinner Shall conform to 4.5 in LACQUER THINNER 10 min Wax Remover Kerosene (Sha ...
Materials Laboratory needed for ASTM Testing of a single oil sample for Wear Metals and Additive Elements to ASTM D-5185, Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
India materials laboratory needed for test the parameters of HDPE,POLYPROPYLENE and ABS samples as follows 1.density 2.Melt flow index 3.Grade name(purity) 4.Tensile Elongation and flexural test 5.Melting point 6.Yield stress 7.Elastic modules kindly send the quotation as early as possible.
India Materials laboratory needed to test the different material like xps foam ,ss,bonding glue,hardner
ISO 17025 certified Laboratory needed for conducting some tests on new metal roof shingles that would be distributed to the US market. These certification tests need to be done in the next few days All testing shall be done per ICC AC166 specifications and they are: - Wind Uplift Test per UL 580 and UL 1897 - Fire Resistance (Class A Material) per UL 790 and ASTM E108 - Impact Resistance (Class 4 Material) per UL 2218 (To include Foot Traff ...
Materials laboratory needed for propane testing for behaviors and properties of propane when pressure drops from 2000 bar to 300 bar, 80 bar, 50 bar and 3 bar within milliseconds, what the temperatures of propane would be within 0,5 milliseconds during this transitive pressure drop.
Materials laboratory needed for polyurethane foam testing
Materials laboratory needed for surface roughness test on 0.8mm surface. Ra cannot exceed 2 micrometers
Europe Materials Laboratory needed for MRL Testing of equiptment paper tissues, ethanol and sealed container for MRL Testing
Manufacturer selling to US market needs materials laboratory for ASTM Testing of Specialty pressure sensitive adhesive tapes to the US market to ASTM 5486, Standard Specifications for Pressure Sensitive Tape for packaging, box closure, and sealing. Based on our analytical data by JIS, G-Tape is classified as Type 1 and Class 1 tape. But we do not have all testing capabilities based on ASTM methods 3654, D-3759, TAPPI T414, D3652, D-3811, D3816, ...
Materials Laboratory needed for ASTM Lubricant Testing to ASTM D4172 four-ball wear testing analysis. Lubicate will have "friction reducing concentrate" additive designed for all lubricant-based applications were wear and fatigue is a potential problem at all operating temperatures and needs to be lessened, alleviated, or guarded against. Needed to expand market to US and Canada so needed to be certified independent lab testing done in the area ...
Europe Materials certification laboratory needed for packaging certificaiton testing to European Union and UN Standards: FIBC UN and EN21898 test certificate, Packaging -- Flexible intermediate bulk containers (FIBCs) for non-dangerous goods. Can you send detailed information and testing costs.
Materials Laboratory needed for ASTM Testing: Accoustic Impedance ASTM E1050
USA Materials Laboratory needed for California Prop 65 testing for Ethyleneimine on LDPE film on which adhesive is applied and is suspected to contain arizidine(Ethylene imine).
Asia materials laboratory needed for ASTM Testing to ASTM C509:Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material
University Researcher needs Southeast USA Imaging Laboratory for TEM/SEM Imaging of cells being coated by nanoparticles
Midwest materials laboratory needed for ASTM testing of multiple reinforced adhesive tape samples for tensile testing
URGENT: Forensic Laboratory needed for natural gas testing for analysis of contaminants we are finding in our natural gas fuel at a power plant. These contaminants are black in color and are liquid, semi solid and solids. They are causing damage to jet engines. We need to identify the materials and possible sources. Samples are available now.
Medical Device Materials Laboratory needed for contact lens testing services provided for measurement of Ion Permiability, Oxygen Permiability, Power, Light Transmission, Diameter, Contact Angle, and Visual Inspection of contact lenses as well as pH, Osmolality of storage solution and package condition.
Materials Laboratory needed to test materials to AMS-STD-2154 Standard method for the ultrasonic inspection of wrought metals and wrought metal products. Material to be tested: STS 416H ,STS 416T sample size to be tested : Dai, 100mm Solid Rod, thickness: 50mm If this is within the scope of your capabilities, please give me your ROM quote or ballpark costs including sample size and turnaround time.
Manufacture of rubber parts and seals for industrial applications needs materials laboratory for certificaiton testing of seals
Nanomaterials Coating company needs toxicology laboratory for toxicity testing on textile substrates. Please send quote
Materials Laboratory needed for ASTM Testing of Plastic Mechanical Fittings for use on outside diameter controlled Polyethylene gas distribution pipe and tubings ASTM F1924
Air purification company needs advanced materials laboratory for deformulation or analysis of nanotechnology coating die release agent used in air purification
California Materials Laboratory needed for ASTM Testing to ASTM E228 -11 standard test method of linear thermal expansion of solid materials with a push rod dilatometer ASTM C600 standard test method of thermal shock test on glass pipe
Materials Laboratory needed to test the absorbance of 5 ZnSe 38mm parts ranging from 8 to 11mm thick.
Europe Materials Laboratory needed for mirror substrate testing of Coated and uncoated mirror substrates, 2x3 samples
India Mechanical Laboratory needed for ASTM Materials Testing of UPVC Pipe & Fitting ASTM D 1785 M Q Plan Test
California materials laboratory needed for ASTM Materials testing of Phase Change Material (PCM) coolers. Humectants, Sodium Hydrates, Higher MW Paraffins.ASTM methods Melting Point, Heat of Fusion, Thermal Conductivity, Density using perhaps modulated DSC, Thermal Conductivity Meter, etc.
Medical Device Materials Laboratory needed for ASTM biodegration testing to support biodegradable claim for a patient belonging bag. We're hoping to get the test done per a standard; we've identified ASTM D5511 (Anaerobic Biodegradation of Plastics) or ASTM D6954 (Oxo-Biodegradable Plastics).
Canada Bioanalytical Laboratory needed for materials testing of lithium soap in Bioprocessing Pilot Plant rheological characterization and tribological test of lithium soap produced by bioprocessing.
USA DEA Schedule 3 pharmaceutical analytical chemistry laboratory needed with experience handling gel formulations and the following excipients for excipient testing: Determination of the content of methyl laureate and glycerol monooelate in a pharmaceutical gel product. **Must be experienced in the determination of these type of excipients in gel formulations. Can handle DEA Schedule 3 materials
URGENT: Materials laboratory needed for adhesive testing to General Motors Standards: test an adhesive to GMW 16443 asap please and what the cost would be.
URGENT: Materials Laboratory needed for ANSI fiberglass panel testing for 2 different fiberglass panels. Burn test, flex test, and drop ball test.
Materials Laboratory needed for ANSI and FMVSS autoglass testing: U.S standard auto glazing testing in accordance with ANSI-Z26.1-1996 and FMVSS 205?
USA Materials Laboratory needed for complete analysis of a sample of an antifoam based on these specific tests FLASH POINT °C ASTM D-93 POLIAROMATIC AND AROMATIC SOLVENTS CONTENT % Weight ASTM D-6730 PH ASTM E- 70 VISCOSITY Cp ASTM D-445 ORGANIC CHLORIDES CONTENT % ASTM D-4929 IR INTERPRETATION-CHEMICAL GROUP ASTM E-1252
Nanotechnology laboratory needed for nanomaterials testing of clean coating for glass and ceramic surfaces by accredited tests: EN ISO 11998 and certifying other properties of the coating, such as adhesion to the substrate, UV weathering (ISO 11507), water contact angle before and after abrasion test, etc. according to accredited tests.
Physical Weathering Laboratory needed for Awning testing for snow and wind load. Determine load carrying capacity
Materials Certification Laboratory needed for biodegradability testing for "doggie pooh" disposable bags. We would like to export bags to Dubai and they need to be certified that they are biodegradable.
USA ISO 9001 certified materials laboratory needed for ASTM Lubricant or Plastics Testing: thermal conductivity testing on lubricants, ASTM D2717 or ASTM D5930
Large engineering company needs Environmental Microbiology Laboratory for bioremediation testing: microbial testing of hydrocarbon impacted soils using bioremediation. We would like to test the microbial population in hydrocarbon impacted soils to discover what kind(s) of microbes are currently present on site and what materials each microbe prefers and how effective the microbes are. Additionally, we would like to test the soil as it is received ...
Plastics Laboratory needed for plastics materials process chemistry research study to perfect a reliable, fast and economical method for creating a thermoset plastic-type compound from rosin and the oil of the flax seed plant. Probable involvement in ASTM testing, NFPA, ISO.
Materials Laboratory needed for ISO Testing of alloys: ISO 2135 Light fastness of aluminum alloys Spec ? ISO 2135 Part is round ( about 21? diameter) ? made of aluminum 2014, weighs around 15 lbs.
Universitry Research Scientist needs Advanced Materials Laboratory for scientific research study: Study of the order-disorder transformations and mechanical properties of metallic alloys (Au-Cu and Au-Cu-Ag)X-Ray Diffraction SEM Scanning Electron Microscopy microhardness measurments, , TEM Transmission Electron Microscopy. The samples used in this study were prepared by melting by using highly pure material to have the following compositi ...
Bioanalytical Laboratory needed with experience in neutralization assays to set up a research program that would require performing a limited number (15-20 mouse serum samples) of neutralization assays for human papillomavirus. Please provide rough estimates of the potential costs depending on whether or not the basic materials for making the relevant pseudovirus would need to be provided.
India materials laboratory needed for paint testing for anti carbonation properties as per EU 1054 / 1066. Pl adv if you have any accredited labs in India for this.
Physical Laboratory needed for UV testing of plastic roof vent . We want ton know how this vent will age and/or long it will it the life expectancy is for this product.
United States Toxicology Laboratory needed for toxicology testing on a variety of plastic materials for orthodontic usage.
United States Materials Laboratory needed for heating fluid testing to ASTM D2688 Corrosion Test - Fluid. ASTM International Accreditation is a MUST
ISO, ILAC, NRTL, KOLAS USA, Canada, China, or UK Materials Laboratory needed for hydrocarbon contamination testing for Determination of Hydrocabon contamination on copper fitting inner surface according with ISO15001. For applications in the pressure range of 50 kPa to 3 000 kPa, not have a level of hydrocarbon contamination greater than 550 mg/m2.
Canada materials laboratory needed for light transmissions testing of window film that claims to block out 99% of UV rays and am interested in a light transmittance test from the 280nm-400nm range (UVB + UVA).
USA materials laboratory needed for Drapability testing of a medical sterilization wraps (textile) from 2 conditions of differing autoclave time, described below. There will be 40 wrapped samples total (10 samples per condition and item number
Middle East materials laboratory needed for ASTM Testing: barcol hardness test glass reinforced plastic to ASTM D 2583, Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impresso
Materials laboratory need for ANSI Testing of window films: test Window film Ansi lab test and strength test
Middle East Laboratory needed for DSC(diferential scanning colorimetry)
Materials Laboratory needed for ASTM Testing; SRI Value Reflectance value which is measured according to ASTM E 903, ASTM E 1918, or ASTM C 1549. Emittance value which is measured according to ASTM E 408 or ASTM C 1371.
United States materials laboratory needed for ASTM Testing of foam to ASTM D3575-BD, Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers compression/deflection, and compression set.
Midwest USA Microbiology Laboratory needed for anti-microbial testing of mesh fabric materials
Materials Laboratory needed for ISO plastic piping testing to ISO 4437:2007 we would like to perform following test on our pipe manufactured with PE100 material, kindly send us testing charges. Sr. no. Characteristic Unit Requirement Test parameter Test method Table 2 Characteristic of PE compound - Tested in pipe form 1) Resistance to gas constituents h ? 20 80°C 2MPa ISO 4437:07 Annex A 2) resistance to rapid crack propagation (RCP) S4 test (e ...
Materials laboratory needed for wax testing: congealing points of waxes for method qualification
India materials laboratory needed for ISO Testing: Test to verify the Oil content % in din,non din and suede leather to ISO 734-1, Oilseed meals -- Determination of oil content -- Extraction method with hexane (or light petroleum)
California construction materials laboratory needed for ASTM waterproofing testing of liquid applied to foundations for - functionality - thickness - de-lamination/ adhesion - bubbling
Middle East, Asia or Europe Materials Laboratory needed for Plastics Testing: ASTM Testing to ASTM D746, Brittleness Temperature of Plastics
ISO Ontario, Michigan, or New York Biomedical Laboratory needed for Biomedical Testing of Plastic models of the Pelvis (axial torsion, strength until failure, etc.) using an Instron (preferably table top) materials testing machine
Materials Laboratory needed for foam testing
United Sates Materials Laboratory needed for copper wire testing for concentration and amount of impurities present in the sample,which elements it contain , how long will the results be ready and how would cost .
FDA GMP Materials Laboratory needed for particle analysis: silica and polyethylene for particle size, molecular weight, density and particle size distribution
Materials Laboratory needed for two custom microscope objectives, which I need to measure their transmission. -Wavelength range: 1000nm-2000nm. -Spectral resolution: 10nm. -Objectives NA: 1)0.2 2)0.85. -Mechanical thread: M40. -Entrance pupil: 1)40mm 2)5mm.
Food Materials Laboratory needed for fruit pressure sensitive adhesive testing of pressure sensitive adhesives to PSAs (USA 21CFR 175.125)that will be used for food contact surfaces directly on fruit hide and on which will be placed a paper label. The fruits will be stored at 4-7ºC until they are displayed in the market. It is a new application and I am looking to present my client with testing results from a recognized third party to PSAs (USA 2 ...
Asia materials laboratory needed for thermal insulation testing or r-value measurement of concrete wall panel
Manufacturer needs materials laboratory for rubber testing to United Nations Economic Commission for Europe Regulation ECER118 annex 6,7,8, Burning behaviour of materials
Canada or USA Materials Laboratory needed for ASTM Testing: NMR analysis to determine percent oil content in wax
USA Materials Laboratory needed for Wear testing for validation of a printing process on a printed insole top coat fabric used for shoe soles. THe process is a heat cured dtg printing process that we are using on on in sole top coats and would like to test the ink durability and wear cycle.
Canada materials laboratory needed for reflectance testing to test mirror samples for reflectance before and after.
Asia metallurgical laboratory needed for Chemical Composition testing: Titanium purity, K, Al, V and F for Ti75. ? Lithium analysis for the following materials: a) Carbon block b) Alumina c) Aluminium Fluoride d) Cryolite
Materials Laboratory needed for exterior latex paint testing: water analysis of latex exterior paint diluted with water prior to application. Sample is dried paint on plywood. Water analysis.
USA Materials Laboratory needed for development of an alternative to DGA analysis transformer oil testing for high levels of gas. We don't need to know exact concentrations in PPM, only if certain gasses (e.g. H2) are abundant (pass/fail). If levels are low, we move to the next transformer; if they are high we note that the transformer needs a full . Test Criteria: Performed in the field, small oil sample volume, immediate results, low cost, gas ...
Materials Laboratory needed for ASTM Testing to be used to judge for the suitability of the short residue as an asphalt binder to ASTM D2892 test method ASTM D5236 method of distillation employs a vacuum pot still
LONG-TERM QC TESTING: Microbiology Laboratory needed for Monthly Coffee Testing of 12oz. roasted coffee packages for : Bacillus cereus, carbamates, Clostridium Perfringens, ochratoxin, organophosphate pyrethroid, pyrethroid, Pseudomonas aeruginosa and thermotolerant coliforms. Macroscopy (identify dirtiness as insect fragments and foreign materials), microscopy (identify whether the package sample has 100% coffee), Arsenic, It'd be 5 pa ...
University Technology Researcher needs India materials testing laboratory for SEM and XRD
Plastic manufacturing factory needs Saudi Arabia materials laboratory for plastic analysis.
Asia toxicology laboratory needed for nanomaterials testing 1. AMES test 2. OECD 404 skin irritation test 3. Water column toxicity with Mysids Bahia I would appreciate getting a quote for the mentioned tests as soon as possible. Thanks Best Regards, Zahra Abyat, Product Development
Materials Laboratory needed for chemical testing for the boiling points of a saturated glucose syrup under different pressures
Large company needs Canada Geology Laboratory for micronizing / crushing cobbles ( 3 buckets of 20 kg) down to 2-3 in size materials.
USA Product Safety Laboratory needed for glove cut resistance testing to ANSI 105-2005 American National Standard for Hand Protection Selection Criteria and/or ASTM F1790, Standard Test Method for Measuring Cut Resistance of Materials Used in Protective Clothing
Midwest or Eastern United States Materials Laboratory needed for Abrasion testing of hard chrome plating and HVOF tungsten carbide coating using ASTM G195 and ASTM F1978
Midwest USA physical chemistry laboratory needed for materials Testing to measure specific gravity of dry soy flour / powder
USA materials laboratory needed for ASTM Testing on beer: Need determination of 4-MEI on beer.
East Coast USA Physical Materials Laboratory needed for Micro hardness testing of silver-plated (less than 15wt% silver) copper flat wire Number of samples not yet known Samples are approximately 0.002in thick Presumably Vickers testing with a diamond tip would work best
India Materials Laboratory needed for houseware testing
Product Safety and Toxicology Laboratory needed for ASTM art material toxicological and safety testing to ensure that art materials meet requirements of ASTM D4236, Standard Practice for Labeling Art Materials for Chronic Health Hazards , art materials, chronic toxicity, craft materials, health labeling,
Europe, Holland or Germany Construction Materials Laboratory needed for test method development. Lab that is capable of developing compressive strength test, moisture content, bulk density, drying shrinkage, and modulus of elasticity to ASTM C1693-11
Materials laboratory needed for SEM Imaging / EDX Analysis the surface of a few parts. Parts are non-conductive and will most likely need a metallic coating. Feature sizes of ~50-100nm will need to be resolved. EDX analysis of the surface is also needed.
Physical materials laboratory needed for hydraulic & gas blistering testing on friction reduction coating to API RP 5L2 and ISO 15741 in a pressure chamber and measurement of physical effects on friction reduction coating
Materials Laboratory needed for petrochemical analysis: Wax Appearance Temperature in Crude Oil by Cross Polar Microscopy (CPM)
Materials Laboratory needed for materials analysis of contaminants To identify composition and phases of contaminant particles on the surface of an exhaust system component
Materials Laboratory needed for NFPA Testing of Wood Panel to pass testing to meet the NFPA 701 fire retardant requirements
Electrical Laboratory needed for ASTM Testing for dielectric strength, the test shall be in accordance with ASTM D149 and the epoxy thickness in the sample shall be 0.125? thick. Minimum 3 samples.
Biomaterials Laoratory needed for determining the ELASTICITY and ADHESIVENESS and GAS PERMEABILITY of our research product (ongoing) which is a coating to surface of wounds. This coating is film-like and is 0.001 to 0.02mm thick (mean thickness).
Materials laboratory needed for ASTM Testing of plastic derived diesel fuel. Oxidation Stability - ASTM D2274 CIC Combustion ION Chromatography test - ASTM 7359.
Medical Textile manufacturer needs materials Laboratory needed for breathability testing. (1) Non woven fabric and (2) PU film medical grade. Both materials need to be tested as per: 1. ASTM E 96, Procedure B (upright cup method) or 2. ASTM E 96, Procedure BW (inverted cup method) or 3. JIS L 1099 (desiccant inverted cup method)
Materials Laboratory needed for destructive testing of sapphire cover glass. Dims, 132(l)x60(w)x0.7mm(thk) Surface finish less than 3 nanometers. Testing needed: Transmission Color Haze Qty to be tested, 700 pieces
Materials Laboratory needed for pressure Testing of Autoclave hollow fiber membrane modules according to a specific pressurization protocol.
Materials Laboratory needed for ASTM Testing : Solar Reflectance Index (SRI) test report of granites according to one of the following methods. ASTM E903, ASTM E1918, ASTM C1549. Waiting for your revert.
Large chemical company needs materials laboratory capable of performing BS EN 1062-6 Paints and varnishes. Coating materials and coating systems for exterior masonry and concrete. Determination of carbon dioxide permeability
Materials Laboratory needed for testing done on steel group material. 1- Tensile test 2- Preparation of sample for Tensile test 3- Bend test 4- Preparation of sample for bend test 5- Hardness test 6- Metallography 7- Preparation of sample for Metallography 8- SEM study (per hour) 9- HIC test 10- SSCC test 11- Salt spray test (per hour)
Materials laboratory needed for ASTM or ISO Testing for for plastic technology softening point for toner resin, using capillary rheometer
Men's dress shoe manufacturer needs laboratory for REACH testing and CPSIA testing. Materials are leather, EVA et TR.
Asia Cosmetics Laboratory needed for Deformulation / Reverse Engineering of skincare products formula of a certain product -- its a skin care oil-based formula, made primarily of virgin coconut oil, moringa extract, and caprylic capric triglyceride (around 90%) plus essential oils. Its a facial oil (for 3 skin types), body oil (for women and babies), soap (for women and babies), and a massage oil. Also, how many of the reference sample ...
Materials Laboratory needed for Rigid Polyisocyanurate (PIR) and Polyurethane (PUR) testing for building end-use applications. As a mandatory requirement our finished products must comply to the Saudi Standards, Metrology and Quality Organization base on adapted standard number - BS 4841-1:2006, BS4841-1-2:2006, BS4841-4:2006 & BSI4841-5:2006 Samples of test which we need are: Thermal conductivity and thermal resistance test Compressive streng ...
Materials Laboratory needed for DIN Testing of testing to Nylon sleeve Aerospace -DIN 65164 Non metallic braided cable sleevings - Part 2: Technical specification. standard by Deutsches Institut Fur Normung E.V.
URGENT Materials Laboratory needed for ASTM Testing: astm d6786 for particle count and filming compound on mineral oil. I'll also need to know the required sample amount for this test. Please get back to me ASAP.
Materials laboratory needed for ASTM Testing of acrylics that need to be tested or analyzed for seam strength. These are two acrylics that are glued together from one end. There is a 1mm gap in between the two acrylics. I need to know the seam strength if you can imagine the two attached acrylics pulled apart. These samples are essentially retail display and measured at most 88mm W x 419mm L x 607mm H and smaller. We are working with a ...
Advanced materials company needed for Japanese Standards for Quasi Drug Ingredients Testing (JSQI) to measure "soluble boron" associated with boron nitride powder. The soluble boron might be present in form of different borates and boric acid on surface of boron nitride platelets. I am looking for a analytical lab that can do soluble boron measurements according to the testing for boron listed in Japnease Standards for quisidrug Ingredients ( ...
USA Materials Laboratory needed for petrochemical testing: Petrochemical physical properity testing for True Vapor Pressure to ASTM D4953, D2879, D 5191
Optical manufacturing company of ophthalmic lenses needs Texas materials laboratory for lens testing of UV-reactive coating for viscosity and water content.
USA Materials Laboratory needed for ASTM Testing coal ash for moisture and unburned carbon ASTM Method Numbers ASTM D3302, ASTM D3173, and ASTM D6316
India materials laboratory needed for ASTM Testing: crude oil testing
USA materials laboratory needed for Product Performance Testing - Oil Defoaming Test 4 defoamers in Group 1, 2, 3, PAO, Synthetic Ester, Vegetable Oil, and PAG Base oils. Tests to be completed: Air Release - modified ASTM D3427 Solubility - method to be discussed Dispersibility - method to be discussed and effectiveness as defined by: ASTM d 892 sequences I thru III and D6082 for seq IV.
USA Textiles Laboratory needed for ASTM Testing of 16 samples product is nonwoven textile material required testing is automotive interior material acoustical evaluation impedance and absorption of acoustical materials using a tube, two microphones, and digital frequency analysis system
Asia Materials Laboratory needed for AIEC and ASTM Testing of Cross linking Polyethylene (XLPE)material useing in Highvoltage cable insulation. We need to test the voids, contamination, Protrusion, Amber of insulating material.
Materials Laboratory needed for ASTM Testing to ASTM C609 - 07(2014) Standard Test Method for Measurement of Light Reflectance Value and Small Color Differences Between Pieces of Ceramic Tile
Materials laboratory needed for ASTM Testing to ASTM C609 - 07(2014) Standard Test Method for Measurement of Light Reflectance Value and Small Color Differences Between Pieces of Ceramic Tile
Glass company needs Materials laboratory for NABL certification testingfor Test Certificate of Fibre Glass product .
Electrical laboratory needed for materials testing: Dielectric Constant according to ASTM D150, - DC Resistance & Conductance according to ASTM D257 - Electrical Resistance according to ASTM D257 OR D991.
East Coast USA materials laboratory needed for silicon testing: FTIR measurements on 40 150 mm round polished silicon wafers
USA Materials Laboratory needed for ASTM Testing: Advanced Ceramics Testing to ASTM Standards: C1470, C20, C623, C1326, C1161, C1424, C1361, C1421, D150, D149,D3755, C657
Plastics Materials Laboratory needed for material tests for ash ,viscosity and melt flow in plastics most tests will be virgin material and a variety of plastic
Saudi Arabia Materials Laboratory needed for Plastic film testing of EVA sheet.All laboratory test required in plastic film industry as will as reporting and SOP development, high skill in PC software word excel..etc
Canada or US materials laboratory needed for Ozone Resistance testing: 100 pphm at 100 hours at 40 degrees C. Product is Luran S 778T, 3-4 samples.
India or Asia materials laboratory needed for ASTM Testing: 1. load deflection test/ fastner pull over test of FRP panels used in cooling tower per ASTM E 72 2. Light transmission test of FRP panels per ASTM D 1494 3.flame spread classification of frp panels per ASTM E 84
United States Materials Laboratory needed for concrete testing
Europe biophysical lab needed for biomaterials testing: conduct three Y-tests
California Materials Laboratory needed for quote first for finding out spec of sample of Nylon 6 or Nylon 6/6 hex head bushings, especially on electrical, insulation and thermal properties.
India Materials lab needed for international level of Filter mask testing to provide the best quality of filter mask to Indian citizen in any case. We are having requirement for filter mask testingas per standard IS 9473 : 2002 & BS EN 149:2001 + A1 : 2009, As given below, 1. Compatibility with skin 2. flammability 3. Co2 content of inhalation air 4. Head harness 5. field of vision 6. Inhalation & exhalation valves 7. Breathing resistance 8. cl ...
USA Radiochemistry Laboratory needed for radioactivity Testing of dental materials by the dental standards ISO 13356 and ISO 6872 by gamma spectroscopy. Standards for dental ceramic restoration and implant materials. Samples are fine, processed zirconium oxide powder for producing dental restoration milling blanks.
URGENT: Materials Lab needed for ASTM testing. 1.-pH (ASTM D1287). 2.-Density (ASTM D5931). 3.-Water content (ASTM D1123). 4.-Alkaline reserve (ASTM D1121). 5.-Ash determination (ASTM D1119). 6.-Metals by ICP-OES (ASTM D6130). Preferent metals: Aluminium, iron, copper & zinc. 7.-Anions by Ion Chromatography (ASTM D5827). Preferent anions: Silicates, Chloride & Sulfates 8.-Boiling point (ASTM D1120). 9.-Glassware corrosion (ASTM D1384)
Large Automotive Manufacturer needs USA Materials Laboratory for silicone material testing: 0.625" x 1.25" Rectangle Extrusion 30-40 Duro Black Silicone (or other colors as approved) Tolerances: RMA E2 "Precision" unless stated otherwise. Operating Temperature Range -40 deg C to 180 deg C To ensure suitability for use in ATEX, IECEx, & CSA applications a Test Report showing the Relative Temperature Index (RTI) - UL 746 is req ...
Europe Accredited materials laboratory needed for fiber testing: -fibre determination and composition(%) -oil rate (%) -fibre linear density -number of crimp -fiber shortening rate due to crimp -fiber section shape -single fiber tensile strength (maximum strength,elongation upon maximum strength, rupture strength)
Germany materials laboratory needed for ABNT and ASTM Testing: Routine test for galvanized material according ABNT (Brazil), standards, or you can propose ASTM or ISO -DIN, equivalent standard. Product: Transformer base ( 900x900 mm,20 mm thicknes), test no.1 and 2. For test no. 3 : sample of 100 x 100 mm
Europe accredited ad member of NANDO materials laboratory needed for flooring system (polyurethane), test on dynamic crack bridging ability in acc. EN 1062-7, method B, class B3.2
India Materials Laboratory needed for physical testing of IR reflecting materials for total solar reflectance. For this, we have some doughty on how to measure the reflection of a particular material / substance with that of another one in near IR range.
USA materials laboratory needed for Fluid compatibility testing of elastomeric gasket material against a specific grade of kerosene to Exxon Mobil Global Practice 06-05-01:?The Vendor shall either verify that the gasket and glue material are compatible with the specified fluids, including chemical cleaning fluids, or submit proof that verification was performed in the past. In either case, the verification shall be performed by the execution of t ...
China materials laboratory needed for adhesive testing: Shear strength and viscosity test needed for for solvent based adhesive
India materials laboratory needed for auto parts testing
Materials laboratory needed to test UPVC fittings for ISO 1452-2 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure
India materials laboratory needed fr ASTM Testing. Test our Rigid Polyurethane Foam for the Thermal Conductivity as per ASTM- C - 177 or IS:3346, Method of the determination of thermal conductivity of thermal insulation materials
India Materials Laboratory needed for ISO Surface cleanliness to ISO 8296-2003 . oil freeness test by ink test/ ARCO TEST on automotive component after cleaning and before painting
Materials Laboratory needed for ASTM or JIS Testing of light blocking capability of curtain . Lab test results according to JIS L 1055 Standard Testing methods for light blocking effect of curtain materials.
Materials Laboratory needed for nylon wristband testing of compressionn band
USA Materials laboratory needed for plastics testing: RoHS quote on plastic components. 3 assemblies Tests seeking: 1.Lead (Pb) 2.Mercury (Hg) 3.Cadmium (Cd) 4.Hexavalent chromium (Cr6+) 5.Polybrominated biphenyls (PBB) 6.Polybrominated diphenyl ether (PBDE) A. assembly has 4 plastic components B. assembly has 2 plastic components, and 1 brass component C. assembly has 4 plastic components
flavor & fragrance company needs professional contract lab for identification testing to identify unknown materials in our flavor & fragrance products. This can be in powder or liquid matrix. Due to the dynamics of our organisation, we need results fast. An example: we find a hazyness in a liquid flavor and we want to know what it is. Or, we find black particles in a powder flavor and we would like to know what it is.
USA Materials Lab needed for optical testing: materials characterization of room temperature surface reflectivity in the 0.3 nm to 3.0 nm wavelength range on a 0.5" or 1.0" diameter sample of Mo5Si3 with a borosilicate glass surface scale.
Europe Laboratory needed for Tekken test or ISO 17642-2 Destructive tests on welds in metallic materials -- Cold cracking tests for 5-10 Samples
Midwest analytical laboratory needed for Quality Control release testing: assay testing on n-heptane solvent samples with validated method. A validated method is required. Needed to release raw materials for pharmaceutical manufacturing.
FDA Laboratory needed for evaluation of organic oil marketed under FDA as "personal lubricant". Need oil analyzed as well as tube packaging materials. 510(k) consulting services neede as well. What is recommended complete process to achieve FDA approval and accompanying charges for services?