Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Material Laboratories to perform their Material Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Material laboratory that would like more information on these Material projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Construction laboratory needed for materials and toxicity testing of naval thermal insulation testing to various standards including: NCD 1427 : SPECIFICATION FOR MINERAL WOOL MARINE BOARD FOR THERMAL AND ACOUSTIC INSULATION ON BOARD INDIAN NAVAL SHIPS
NCD 1433 : SPECIFICATIONS FOR ELASTOMERIC NITRILE THERMAL INSULATION FOR USE ONBOARD INDIAN NAVAL SHIPS
ISO 17025 certified laboratory needed for OECD physical / chemical testing of solid materials and an octanol / water solution as per three OECD standard methods: OECD107 Partition Coefficient (n-octanol/water): shake flask method , OECD 117 Partition Coefficient (n-octanol/water), HPLC method, and OECD123 Partition Coefficient (1-octanol/water): slow-stirring method
LONG-TERM TESTING Materials laboratory needed for ASTM physical, mechanical, and accelerated aging testing of polymer auto parts to car manufacturers specifications WSS-M2D496 (Ford), GMW 14196 (General Motors), MS-AY-549 (Chrysler-Fiat) including: WSS-M2D496 Density to ASTM D3574-16 Test A Tensile Strength to ASTM D3574-16 Test E Elongation at Break to ASTM D3574-16 Test E Tear Strength to ASTM D624 Die C Compression Set to ISO 1856 Method A Compression Deflection Stress ISO 3386-1 +A1 Heat Aging to ASTM D3574-16 Test K, ISO 3386-1 +A1 Humidity Aging to ASTM D3574-16 Test J, ISO 3386-1 +A1 Dimensional Stability to WSS-M2D496, 3.5.10 Fogging to SAE J1756 Odor to FLTM BO 131-03 Variant B Cold Flexibility to FLTM BN102-01 Method A Solvent Resistance to WSS-M2D496 Flammability to ISO 3795 GMW 14196 Testing Emissions per GMW
LONG-TERM TESTING Materials laboratory needed for ASTM & FED-STD textiles testing for non-fibrous and soluble materials content using soxhlet extraction procedure to FED-STD-191 and absence of detectable silicone grease and oil determined by Fourier Transform Infrared Spectroscopy (FTIR) analysis by sample extractions using ASTM D 1836
LONG-TERM TESTING Pharmaceutical analytical chemistry laboratory needed for raw vitamin and nutritional supplement materials purity & impurity testing by HPLC analysis for: 72-18-4, L-Valine; 3040-38-8, N-Acetyl-L-carnitine; 5785-44-4, Tricalcium Dicitrate Tetrahydrate; 3344-18-1, Tri Magnesium Dicitrate; 6100-05-6, Potassium bicarbonate; 4468-02-4, Zinc(II) Gluconate Dihydrate; 10024-66-5, Trimanganese Dicitrate; 527-09-3, Copper Gluconate; 10060-12-5, Chromium(III) Chloride Hexahydrate; 13410-01-0, Sodium Selenate; 13446-49-6, Potassium Molybdate; 1303-96-4, Sodium tetraborate decahydrate; 7681-11-0, Potassium Iodide; 919-16-4, Trilithium Citrate; 135459-87-9, Strontium Ranelate; 127-47-4, Vitamin A: Retinylacetate (all trans); 67-97-0, Vitamin D3: Cholecalciferol; 58-95-7, Vitamin E: D-Tocopherylacetat; 84-80-0, Vita
LEGAL Materials laboratory needed for performance, weathering and failure investigation testing of potentially defective, two coat, acrylic elastomeric liquid coating used for roofing on commercial building. Polymer coating that instead of coating and drying within two hours discharged into storm drain causing notification of Fire department and Hazardous Materials units.
NIOSH laboratory needed for industrial hygiene testing: hazardous material surveys for asbestos, lead (Pb), tributyltin (TBT), poly-chlorinated biphenyls (PCB), and mercury. Please provide a quotation for asbestos sampling, screening, and analysis (by PLM method).
Material analysis laboratory needed for the following testing on plastics:
Environmental Cycle test after 50 cycles according to PV 2005
Lightfastness according to PV 1303 after 3 period of exposure
Grey scale level, color and grain according to color combination, color consistency according to VW 501 90, resistance to open air weathering VW 50185: without complaints, temperature resistance and operable from -40ºC to 90ºC, emission behaviour according to VW 501 80, and flammability according to TL1010
Engineering company needs materials laboratory for environmental simulations testing of GRP (Glass-Fibre Reinforced Plastic) ground anchor for UV stability testing in accordance with ES ISO 4892-2 , performance at elevated temperatures is in accordance with ACI440.3R-04 Section B.6 Accelerated test method for alkali resistance of GRP bars, and suitability, Durability,
Materials Laboratory needed for testing on a steel grade silica ceramic blanket.
Flammability to ASTM F 1462.
Thermal Conductivity to ASTM C518-19983.
Thermal Shock Resistance to ASTM D-30324.
Chemical Sustainability to ASTM D-6455.
Mineral Wool Thermal Insulation to IS 3144:1992
Heavy Metals Resistance to Biological Catching (Hazardous Substance)
Food laboratory needed for ISO spice testing of saffron to ISO standards ISO 3632specifications for dried saffron obtained from the pistils of Crocus sativus L. flowers. and ISO 3632-1-2010) . Please specify the cost/test; quantity of saffron required; and turn around time once the lab receives the material.
Pharmaceutical laboratory needed for ICH, FDA, and USP testing on OTC sunscreen API and finished topical products including: 1) stability test on our finished sunscreen products for the claimed shelf life of 3 years as per the US FDA requirement, 2) preservative challenge test as per the USP on finished sunscreen products, 3) assay and purity of the following active raw materials: avobenzone [INCI name : Butyl Methoxydibenzoylmethane] 2. homosalate 3. octocrylene 4. octisalate [INCI name : ethylhexyl salicylate] 5. oxybenzone [INCI name: benzophenone]
Please provide cost of each test, turnaround time estimate, and sample quantity required for assay and purity testing of each active API.
Plastics / Materials Laboratory needed for ASTM physical testing of plastic crates from different suppliers including: Raw material tests as per ASTM D4976 + ASTM D5203, density, melt flow rate, elongation at break, tensile strength, UV resistance, stress crack resistant, impact test as per SASO-GSO 1863.
Construction company needs materials laboratory needed for ASTM testing of insulation material to ASTM C1371 Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers , emissometer, emittance and ASTM C1549, Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer. Company from Turkey.
Geo-electrical laboratory needed for testing of ground enhancing materials according to IEC 62561-7:
1. Leaching test - Based on EN12457 - 2 Part 2 and EN ? 12506
2. Sulfur test - Based on ISO 4689-3 : 2004
3. Corrosion test - Based on LPR method (Linear Polarization Resistance Method)
Polymer laboratory needed for Tg (glass transition temperature) testing of a polyacrylate, which is provided in an emulsion. Determination of Tg of a polyacrylate, which is provided in an emulsion mixture. The emulsion includes the polyacrylate, an additional polymer (which may also be a polyacrylate), water and at least two more non-polymeric materials.
Materials laboratory needed for ASTM testing for fire extinguisher compliance and safety testing to meet AHRI standards using the following guidelines:
- Purity (according to ASTM D6806)
- Acidity (according to AHRI 2008 Appendix C to 700-2014 Part 1, to be confirmed by the 2BTP producer)
- Water content (according to AHRI 2008 Appendix C to 700-2014 Part 2)
- Nonvolatile residue (according to AHRI 2008 Appendix C to 700-2014 Part 3)
- Suspended matter or sediment (visual inspection during Nonvolatile residual test)
- Presence of Stabilizers (FTIR spectrum analysis to be performed)
Microbiology Laboratory needed for ASTM or ISO biodegradability testing to ISO14855 Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions Method by analysis of evolved carbon dioxide or ASTM D5338 Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials Under Controlled Composting Conditions, Incorporating Thermophilic Temperatures
Packaging laboratory needed for complete packaging testing of 7 SKU's of products including: material testing, and benchmark packaging Bottles: Drop test, seepage test, topload test Caps: Capping force test, torque test Labels: Fadeometer test, chamber test, resistance test - Rigids: Bottles, Caps, Jars - Flexibles: Labels, Films - Paper-based: Corrugates, Cartons - Others: Pumps, Tubes
It would be great if you could share your credentials outlining: - Specific tests you offer in the above categories - Turnaround time - Quotations
If you could give me a call today, I am happy to discuss our requirements in more detail.
Materials Laboratory needed for Corrosion testing of molybdenum disulfide according to AMS-M-7866A. Tests required are:
1.Corrosion resistance in accordance with MIL-STD-791 2.Steel and copper corrosion. Performed on steel panels conforming to MIL-S-7952 and copper panels conforming to QQ-C-576.
Materials Laboratory needed for AASHTO testing of Architectural coating Material to Chloride penetration test (AASHTO T259, T260) Rapid chloride Permeability AASHTO T277 C02 Permeability Coatings and Films Materials laboratory for ASTM paint testing 1. Anti-carbonation: Test method EN-1062-7 2. Liquid water permeability: Test method EN-1062-7 3. Acid Resistance . 4)SRI
Materials laboratory needed for screw DIN Testing: 1) Screw Type: DIN7500 PE M3X8 Properties Class: 8.8 Surface protection: DIN EN ISO9227-NSS 360h Cleanliness requirement: TV-02023-EN SKII (166mm2)
2) Screw type: DIN7500 PE M4X10 Properties Class: 8.8 Surface protection: DIN EN ISO9227-NSS 360h Lock washer type: DIN128A M4 Lock washer material: A2 Cleanliness requirement: TV-02023-EN SKII (356mm2)
Research and Development Laboratory needed for product development studies for the development of new concentrated granulated fertilizer material processed from zeolite material (sand) into concentrate with the highest possible purity (using magnetic separation), and then from concentrate produce granulated fertilizer/material.
Materials laboratory needed for DIN fastener cleanliness testing to Screw Type: DIN7500 PE M3X8Properties Class: 8.8Surface protection: DIN EN ISO9227-NSS 360hCleanliness requirement: TV-02023-EN SKII (166mm2)2. Screw type: DIN7500 PE M4X10Properties Class: 8.8Surface protection: DIN EN ISO9227-NSS 360hLock washer type: DIN128A M4Lock washer material: A2Cleanliness requirement: TV-02023-EN SKII (356mm2)Please advise.Thanks.
Polymer laboratory needed for EPA and ASTM materials testing of a O/W micro-emulsion matrixColor; Physical State; Odor; Explosive Properties; Oxidising Properties & Incompatibility; Flammability; pH; Non-Newtonian Fluid Dynamic Viscosity; Relative Density; Storage Stability at 54 C for 14 days and ASTM G31 Corrosion Characteristics.
Materials laboratory for ASTM paint testing 1. Anti-carbonation: Test method EN-1062-7 2. Liquid water permeability: Test method EN-1062-7 3. Acid Resistance . 4. SRI (solar reflective index) ASTM C 1549-04 5. Chloride Ion penetration ASTM C 1202 -97 6. Water Absorption ASTM D 870 All above tests for water based paint
Materials laboratory needed for IEST and ASTM Clean Room Gloves Testing: 1 Tensile Strength ASTM D412 2 Ultimate Elongation ASTM D412 3 Surface Resistivity @50%RH ESD/EOS S11.11 4 MVTR 5 Shedding and extractables - IEST RP-CC005.4 LPC ? 0.5 ?m, Cl?, NO3-, Zn2+, SO42+, Na?, K?, Ca2+, Al3+, Fe3+, Cu2+, Total NVR in IPA
FDA GLP Preclinical Laboratory needed for PCR viral testing of two regenerative drug products and raw materials using Pharmacopeia methods: 1. HIV (anti-HIV (I/II), 2. Human T-Lymphotropic virus I and II 3. Cytomegalovirus 4. Epstein-Bar virus 5. Hepatitis C 6. HBV (HBsAg & anti-HBC)
In order to stay in line with the pharmacopeia guidelines, we would like to perform detection of the former viruses on our products with the PCR method.
Major Genonmics Medical Research Center needs virology laboratory for anthrax and other testing on mammoth bone sample from Russia prior to doing DNA study on ancient DNA. Recent news, reported an anthrax outbreak in Siberia from carcasses underneath melted permafrost. The exact precedence of this sample in Russia its unknown, and we wouldn't like to take any risks regarding possible sample contamination.
We would thank you any help you could provide us with, regarding the testing and safety to use this material, Thanks very much cynthia
Urgent Need by Large UAE construction company for testing of foam materials per BS EN 13468 (Thermal insulating products for building equipment and industrial installations. Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH) and (AGI Q135).
Metal Fittings company needs microbiology laboratory for biocidial efficacy testing of product surface testing according to EN ISO 22196 and TS EN 15457 standards. We are a fittings company. Our base material is brass. We plate it with first nickel and then chrome. We apply a biocide on chrome layer.
UK Company needs a laboratory to test Adipic Acid as a raw material for to be used in manufacturing for: 1. Purity 2. Heavy metals residue (to the ppm and ppb levels) 3. Other impurities such as byproducts from the manufacturing process (succinic acid, Caproic acid ? etc.) 4. Volatile and semi-volatile impurities. (by LCMS for example)
Company needs materials laboratory for Failure Analysis Testing of welded seam strength in air supported structures made out PVDF 28oz vinyl fabric. The seams of the fabric are RF welded together to create the structure and we have been having some issues with our seam strength lately
Need laboratory testing for VOC content in adhesive material to comply with SCAQMD rule #1168, shall be determined by USEPA'S Test Method 18, or Air Resources Board (ARB) Method 422 for the determination of emissions of Exempt Compounds and USEPA's Test Methods 25, 25A, SCAQMD's Method 25.1, or SCAQMD Test Method 25.3. (Determination of Total Gaseous Non- Methane Organic Emissions as Carbon)
ASTM Testing of aluminum honeycombs to multiple ASTM standards: .ASTM C273 - Standard Test Method for Shear Properties of Sandwich Core MaterialsASTM C365 - Standard Test Method for Flatwise Compressive Properties of Sandwich CoresASTM C297 - Standard Test Method for Flatwise Tensile Strength of Sandwich ConstructionsIf you offer testing of aluminum honeycomb core, please provide a quote the three tests and for multiple honeycomb cell size.
Materials laboratory needed for IEC and ASTM Testing of insulators (several tests) : ASTM C177: Standard test method for steady-state heat flux measurements and thermal transmission properties by means of the guarded hot-plate apparatus. (We only have the similar test as per attachment.)
· IEC 60383-2 (Equivalent to JIS C 3801-1:1999): Insulators for overhead lines with a nominal voltage above 1000 V - Part 2: Insulator strings and insulator sets for a.c. systems - Definitions, test methods and acceptance criteria
· ASTM D2303: Standard test method for liquid-contaminant. Inclined-plane tracking and erosion of insulating materials.
· IEC 60587: Electrical insulating materials used under severe ambient conditions ? test methods for evaluating resistance to tracking and erosion.
Laboratory needed for Fire rating testing to NFPA 701, NFPA 705, German fire code, Australian fire code, and UK fire code. Material is a nylon mesh material used in a performance environment that has been spray coated with a proprietary light diffuser and fire retardant
Materials laboratory needed for NATO coatings testing of chemical agent resistant coating (CARC) to North Atlantic Treaty Organization NATO AEP 64 standard fo Performance Requirements for Paint Systems Resistant to Chemical Agents and Decontaminants, for the Protection of Land Military Equipment and 65 coded Standard, described as Performance Requirements and Test Method for Paint Systems Resistant to Chemical Warfare Agents, for new new coating project to:
Screening Test (Resistance to Tri-n-Butyl Phosphate) onAluminium Alloys: 2024-T3 unclad, 5083 and 7020-T8
Optical Characteristics: *Visual comparison of the colour of the paints *Specular Gloss *Colorimetry on Aluminium Alloy 5083 or 7020-T6 and Steel
Scratch Hardness on Aluminium Alloy 5083 or 7020-T6 and Steel
Flexibility (Cupping test) on Aluminium Alloy 5083 or 70
Materials Laboratory needed for ASTM Testing of Processed woodcore Panel Board assemblies (using core material such as MDF / Particle Boards, Laminates, Edge Banding etc etc ).We are looking for Test Certification for ?ASTM E84-06a? for surface burning characteristics of the Finished Panel Board assemblies (where we would like for the Test to make specific reference to the actual assembled components for Wood-core Panels including core, Laminates and Edging.
Materials Laboratory needed for ANSI Testing of Latex Coated Multipurpose Work Glove to be ANSI rated for Cut and Abrasion Resistance as demonstrated by an independent laboratory testing report (if certified to ANSI/ISEA-2016, Cut Level A2 and Abrasion Level 3). Thank you so much for your assistance in this matter.
Large company needs materials laboratory needed for accelerated aging study on thermoset material with for yellowing index and light transmitting to identify the relationship between the hours accelerated test and the years of outdoor exposure.Please, send me the costs for tests and measurements and samples dimensions.
Materials Laboratory needed for Material characterization of metal with Polymer thinfilm - Mechanical properties characterization of flat thin steel (0.1 x 5 x 30mm) - Mechanical properties characterization of bent thin steel (0.1 x 5 x 30mm) down central axis - SEM imaging and cross sectioning of of metal+polymer thin film for thinfilm measurement
Nanotechnology company needs materials laboratory for conducting studies on nanoparticles effect on the base polymers. polymer composite testing on various polymers, including PP, PE, Nylon, TPU, and others. In particular, we are interested to learn the mechanical performance (Tensile Strength, Izod Impact, Young's Modulus), Gas Permeability, Colorant Properties, Coefficient of Friction reduction, creep properties, thermal conductivity, and electrical conductivity polymer samples: Tensile Strength, Young's Modulus, Gas Permeability, Thermal Conductivity, Electrical Conductivity, Impact Strength, Creep, UV Irradiation, Colorant, Melt Flow Index, Nucleation
LONG-TERM TESTING Packaging Laboratory needed for packaging testing of In flexible packing materials like double laminated , triple laminated & other flexible packaging material for: Flex crush resistance Water vapor transmission rate Oxygen transmission rate Optical density Lamination bond strength
Materials laboratory needed for surgical gowns testing - NFPA Standards - Standards for the use of Inhalation Anesthetics.
- ASTM 1670, Standard Test Method for Resistance of Protective Clothing Materials to Synthetic Blood.
- ASTM 1671 Test Method for Resistance of Protective Clothing Materials to Penetration by Bloodborne Pathogens Using Viral Penetration as a Test System.
- ANSI/AAMI PB70:2012, Liquid Barrier Perfrmance and Classification of Protective Apparel and Drapes Intended for Use in Health Care Facilities.
- ASTM F2407-06, Standard Specification for Surgical Gowns Intended for Use in HEalthcare Facilities.
- ASTM F1670-08/F1670M-08, Standard Tests Method for Resistance of Materials Used in Protective Clothing to penetration by synthetic blood.
- ASTM F1671/ F1671M -13, Standard Test Method for Resistance of
Bioanalytical Laboratory needed for cell viability (MTT), cell proliferation studies (flow cytometry to characterize CD) and self-renewal studies including tagging of stromal vacular factor (SVF) cells using superparamagnetic iron oxides (SPION) and characterize the tagging using colorimetric assays such as Prussian blue staining. In addition,cell viability, studies (MTT), self-renewal studies (flow cytometry to characterize CD) and cell proliferation studies are needed after the tagging has been performed.
LONG TERM TESTING Materials Laboratory needed for Polyamide Tube testing to prove compliance with DIN73378, DIN74324-1 and SAEJ844 Many different tests covering material mechanical properties, hydrostatic burst pressure, impact testing, moisture absorption, stiffness, cold temperature flexibility, chemical resistance, extractables, heat aging, thermal stability, artificial weathering and UV resistance.
Construction Buildings Materials company needed for ANSI or ISO adhesive testing to ANSI A118 or ISO 13007 Test adhesive tensile strength at normal temperature and water immersion *Determination of tensile adhesion strength - C *Determination of open time * Determination of slip
Environmental Laboratory needed for mineral analysis in soil samples: X-ray analysis, particle size analysis was carried out on each sample to separate and prepare the clay fraction for the analyses. Samples were prepared for XRD Analysis using a back loading preparation method. 10 % internal standard (fluoride) was added and the sample micronized. The micronized material was analysed by XRD utilizing a Panalytical Empyrean Diffractogrameter with PIXcel detector and fixed slits with Fe filtered CO-k alpha radiation. Phases were identified using X? Pert High score plus software. XRD analysis was used to determine the crystalline mineral phases present in the sample. The abundance of each phase (weight %) was determined by the Rietveld Refinement method. An orientation specimen was prepared from each of the samples, the head and the clay (
Materials laboratory needed for thermal conductivity testing of thermal paste used in computers, and we need to measure the actual thermal conductivity for the sale of goods. Currently developed several modifications to the calculated thermal grease thermal conductivity in the range of 0.7 - 6 W / (m * K).
Materials laboratory needed for DIN and ASTM Testing of thermal insulations foam board. Testing to To meet out the requirement of Density: DIN 53420(ASTM D 1622 Thermal conductivity :DIN 52612 OR 52616 Compressive strength :DIN 53421 (ASTM D 1621 Water vapour diffusion resistance factor: DIN 52615 Water vapour permeability : ASTM C355 Heat soaking : DIN 52328 Water absorption by submersion : DIN 53428 (28 days submersion) ASTM D 2842
Large petroleum company needs materials laboratory for ASTM Testing of terephthalic acid to ASTM methods
ASTM D8031-16 ? Acid number for TA by potentiometric titration ASTM D1209-05 ? Color of clear liquids (Pt- Cobalt Scale)
- Cost/analysis - Turnaround - Sample amount required
FDA compliant food laboratory needed for characterization of a natural extract (including microbiological analysis and analytical support) with the goal of filing a petition of new color additive with the FDA on 5 different batches of materials for total aerobic count, Salmonella, E. coli, yeast, and mold. We are also interested in analytical support for carbohydrates, proteins and lipids content of the same extract batches.
Medical Device Company needs medical technology laboratory for packaging/ product /development of developing a disposable medical cable assembly that will require sterilization. ABS plastic housing for connectors Silicone vs PVC for cable assembly I have questions about cost, materials, packaging and logistics.
Scientific researcher would like bioanalytical laboratory for research study using measures of salivary cortisol and oxytocin. Need budget for purposed of preparing a grant proposal, and need urgent information regarding the costs implicated for the collection material, assays, and lab analyses work.
Contract laboratory needed for clay analysis on clay mineral content by XRD ANalysis. For X-ray analysis, particle size analysis will be carried out on each sample to separate and prepare the clay fraction for the analyses. Samples will be prepared for XRD Analysis using a back loading preparation method. 10 % internal standard (fluoride) shall be added and the sample micronized. The micronized material will be analyzed by XRD utilizing a Panalytical Empyrean Diffractogrameter with PIXcel detector and fixed slits with Fe filtered CO-k alpha radiation. Phases will be identified using X? Pert High score plus software. XRD analysis will be used to determine the crystalline mineral phases present in the sample. The abundance of each phase (weight %) will determined by the Rietveld Refinement method. An orientation specimen will be prepared
Asia Materials laboratory needed for ASTM Testing to ASTM F1671, Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System and ASTM F903, Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Liquids
Europe Materials Laboratory needed for Paint film performance tests on mild steel panels Sr No Test 1 Salt Spray Test (504 hours) 2 Humidity Resistance (504 hours) 3 Pencil hardness 4 Dry Adhesion 5 Elongation 6 Impact Resistance (direct) 7 Impact Resistance (indirect) 8 Colour Matching (Visual) 9 Colour Matching (Instrumental) 10 Metamerism Index 11 Gloss 12 Wet Adhesion 13 Chip resistance 14 Immersion Primer 15 Machinability 16 Superior weathering for gloss and colour retention
Materials laboratory needed for ASTM Dielectric Testing: Dielectric Strength and Water Absorption (RT 24h) to ASTM D149, Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid. The material is 30% glass filled Peek. What test sample size and qty is needed? What is price and delivery?
Materials laboratory needed for ASTM Testing for compatiability of plasticizers to ASTM D3291 Testing (Standard Practice for Compatibility of Plasticizers...).Lab would need to accept samples of the plasticizer, and then formulate into the PVC, then perform the analysis.Approximately 10 samples.
Materials laboratory needed for paints testing for accelerated aging, hiding power, the spatter resistance, the scrub resistance, the washability, the sag resistance, the blocking resistance, the hiding change, the heat gain, the viscosity, the whiteness-yellow index, the washability, the resistance to water and the resistance to accelerated ageing.
Physical Laboratory needed for flammability pre-testing of carbon fibre samples to CS 25.853 Flammability Requirements for Aircraft Seat Cushions Appendix F, Part I, (a)(1)(ii) (i.e. 12sec vertical burn with 305mm x 70mm samples). The objective is to try 2 or 3 different materials to assist material selection and build up some confidence before testing at the lab required by our customer.
University Researcher needs materials laboratory for rheological testing of EPDM rubber compound which include viscosity vs shear rate ,dynamic modulus loss and storage moduli and tan delta. I need these data for material characterizing and extract material parameter required for rubber extrusion.
Materials laboratory needed for paints testing for accelerated aging, hiding power, the spatter resistance, the scrub resistance, the washability, the sag resistance, the blocking resistance, the hiding change, the heat gain, the viscosity, the whiteness-yellow index, the washability, the resistance to water and the resistance to accelerated ageing.
Materials Laboratory needed for biomechanical / biophysical testing for medical device burs: ¬Mechanical force of d¬evices test (compress¬ion, Torsion) Biomechanical property of dental burs is important for safety usage so test should assure torsional yield strength, torque, breaking point of dental burs moreover determine compression load force of device on rigid test block. Test apparatus should be arranged for axial force. 5.¬ ¬? compression and fat¬igue test and standar¬ds Fatigue test is especially for multi-use burrs, So company should proves that performance of product does not change after pre-determined numbers of multi- usage.
Medical Device Manufacturer needs medical device laboratory for sterilization validation of device sterilization process. 1.¬ ¬Sterilization method: ¬ We will supply instr¬uctions for a method ¬with step by step ins-tructions and we need¬ to get the steriliza¬tion validation ? the¬y will be autoclaved Yes it is correct but you should validate your steam sterilization parameters, temperature,duration,pressure etc. After you sterilize your products according to your set values. you confirm with sterility test that No Microbial Contamination on products. Cleaning and Sterilization Instructions Spring FG Diamond Burs are non-STERILE, but should be cleaned and sterilized before use and subsequent reuse. .
Ultrasonic Cleaning Procedure Prepare a fresh pH-neutral cleaning solution; place the Diamond Bur in the dedicated instrum
Materials laboratory needed for independent third party testing of laminate flooring for
1) Test for ortho phthalate plasticizers
2) Following tests with relevant ASTM test parameters (for vinyl flooring) - Stain and chemical test - Static load limit - Dimensional stability - ASTM 648 - fire test - ASTM 662 - smoke test
3) Following tests for EN / ISO parameters i) ISO 10581: Homogeneous Flooring including all the sub standards - ISO 10874 - this is part of 10581 (classification of use) - EN 660-2: Abrasion Resistance
ii) Standards as per ISO 14041 (CE Mark) - EN 13501-1: Fire standard - ISO 11925: Fire standard - EN 13893: Slip resistance - EN 1815 / 1081: Electric resistance standards - EN 717-1: Formaldehyde and PCP content testing - ISO 16000-6: VOC Emission testing
iii) Additional Standards - ISO 846, p
FDA cGMP Pharmaceutical analytical chemistry laboratory needed for identity testing for the following drug and excipient materials that may be used in production of clinical grade biological drug products: Pluronic F-68 1X Phosphate Buffer Saline L-Glutamine Plasmids F-17 Serum Free Media CDM4HEK293 Media Sterile water WFI Clinical 293 Suspension Cell Bank Polyethylenimine (PEI) Max. MW 25,00010X Phosphate Buffer Saline 1M Tris, pH 9.0 Tris(hydroxtmethyl) aminomethane 1M Tris-HCl, pH 8.0 10mM Tris, pH 8.0 1X Phosphate Buffer Saline 5M Sodium Chloride Solution Benzonase® endonuclease, purity grade I (?99%) Hydrochloric acid solution 6N Optiprep Phenol Red Sodium hydroxide solution 0.5N Sorbitol Sterile WFI Water 1M Magnesium Chloride Ethyl Alcohol 200 Proof
Aerospace company needs materials laboratory for investigation study of delamination problem with decor laminating application.by coupled TGA-MS (Thermalgravimetric Analysis and Mass Spectrometry) to detect if offgassing occurs. We often see delamination or air bubbles popping in the interface between decor film and surface of honeycomb sandwich panel. We would like to know if there offgassing of film affecting the strength of adhesive causing delamination/air bubbles. (note: air are entrapped in honeycomb sandwich panels. thus offgassing might occurs when the air escapes from the core to the surface and is brought contact with the adhesive)
Electrical Home appliance manufacturer needs Microbiology Laboratory for antimicrobial efficacy testing of UV-light on sterilization. 1. Textiles inoculated bacteria is to be washed in our machine and bacteria reduction is analyzed on textiles. (UV program is to be activated) 2. Empty machine having test material that are inoculated by bacteria adhered to the surface of drum is to be tested and the test material is to be analyzed in terms of bacteria reduction. (UV program is to be activated).
antibacterial tests on washing machine? which bacteria should be tested? which standards do you follow?
Larg Construction Building Materials company needs certification laboratory for ANSI Testing of tile adhesives & grout accoding to ANSI standards. FK10W Cementitious tile adhesive C1T EN 12004 GM1 Cementitious tile adhesive C2T EN 12004 FLS1000 Cementitious tile adhesive C2TES1 EN 12004 DB2000 Cementitious tile adhesive C2TE EN 12004 COLORFILL Cementitious joint grout CG2 EN 13888
Please provide pricing for quots.
Analytical chemistry laboratory needed for HPLC, SEM, or FTIR soap testing for Identification of white powder being formed soap bars being manufactured in large quantities after the curing process. The white powder just started forming after larger amounts of organic caffeine was added during the mixing process and the soap bars are curing for more than 48 hours. Pictures can be provided with a basic microscopeexam with 1,000x magnification to determine that this powder was not mold, however, the lab I used does not have HPLC, SEM, or FTIR available for further testing.
I believe that the white powder could be either soda ash (sodium carbonate) or possibly caffeine, since we add organic caffeine powder to the soap bar. A quick Google search reveals that many lye soap manufacturers have issues with a white powder on their soap bars whi
LEGAL Materials laboratory needed for measuring surface of a flexible thin film material to characterize a few topographical features such as surface roughness Ra.
Contact mode AFM testing in ambient; non-contact optical interferometric profilometer such as Wyko profilometer.
Capable to scan 200x200 um area of sample, with resolution down to 0.5 nm roughness for smoothest materials.
ELECTRICAL LABORATORY NEEDED FOR EN AND ANSI BASE PHOTOCELL TESTING (RECEPTACLE) TO ANSI C136.10: 2006 AND NTC 2470, Contact endurance test, Material and capacity of current contacts , Insulation Resistance, Dimensions, sizes and types of conductors connecting the tips, the basis for photocontrol, Base material or recetaculo connection, Dimensional analysis, Maración
Materials Laboratory needed for ASTM tensile testing to ASTM E8.,Standard Test Methods for Tension Testing of Metallic Materials. Flat tensile specimen will need to be machined according to ASTM E8 from 6061-T651 slug that is 2.75 in diameter and 8 in length. Material should meet the requirements of AMS QQ-A-225/8A. Please provide quote and delivery time. Thank you.
Materials Laboratory needed for Biodegradation testing of Plastics as per ASTM D5511, Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions and ASTM 5526, Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under Accelerated Landfill Conditions etc..
ENGINEERING LABORATORY NEEDED FOR PROCESSING AND PROCESS DEVELOPMENT FOR PROCESSING OF GRAPHENE AT HIGH TEMPERATURES TO REMOVE IMPURITIES. COMPANY WISHES TO WORK MORE CLOSELY WITH LABORATORY TO IDENTIFY THE IDEAL CHEMISTRY TO ACHIEVE THIS . THE FIRM COULD ALSO CHOOSE TO BAKE THE GRAPHITE A TEMPS AS HIGH AS1500 DEGREES C .THIS WOULD ELIMINATE SOME OF THE IMPURITIES TO ACHIEVE 95% + AND ALSO KEEP THE MATERIAL VERY DRY ,
Laboratory needed for ASTM tensile testing to ASTM E8.,Standard Test Methods for Tension Testing of Metallic Materials Flat tensile specimen will need to be machined according to ASTM E8 from 6061-T651 slug that is 2.75 in diameter and 8 in length. Material should meet the requirements of AMS QQ-A-225/8A. Please provide quote and delivery time. Thank you.
Materials Laboratory needed for ASTM Testing: Stress corrosion Testing on titanium according to ASTM F945. Candidate solution is the lubricant Test specimens shall be made of AMS 4911 material. The traceability of the specimen shall be done with a metal tag attached to the specimen
Please provide a quote.
Third-party laboratory needed for biodegradability testing of plastic fishing baits for fishing potentially to ASTM D6691Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum as the most appropriate test.
Biomaterials laboratory needed for in-vitro surgical sealant testing 1. Burst test of surgical sealant (2-PEGs) as per ASTM F2392. 2. Gel Time test - surgical sealant (2-PEGs) 3. Swell Test - surgical sealant (2-PEGs) 5. Gel Mixing test - surgical sealant (2-PEGs)
Materials laboratory needed for rubber testing for Hexane extract, Thermal analysis (DSC, DMA, TGA) , EDX analysis (REM) of the material for heavy metals (Pb, Cr-VI, Hg, Cd), TDS-GCMS analysis of the material for softeners, Extractable matter (extration agent: n-hexane) % (Max) Tg (tan ? max) on sheet material (°C), Shore A Hardness on sheet material @ -40°C For 144 Hrs, Corrosion resistance @ 100°C for 24 Hrs.
ENvironmental laboratory needed for waste oil , soil and water testing for Radium 226/228 & other Gamma Emitters EPA 901.1 modified Waste and Oil Samples 40 samples, Fluorescent or High Intensity Discharge Lamp Preparation ANSI/NEMA: C78.LL 1256-2003/C78.LL 3-2003 Waste and Oil 10 Samples, Volatile Organic Compounds TO14A Air and Soil Gas 50 samples, Volatile Organic Compounds TO15 Air and Soil Gas 50 samples, Mercury 7471A or NIOSH 8009 Air and Soil Gas 20 samples, Volatile Organic Compounds CLP method w/pkg. Groundwater, surface water, or leachate 10 samples, Base Neutral Acid Compounds CLP method w/pkg. Groundwater, surface water, or leachate 10 samples, Base Neutral Acid Compounds 525.1 Groundwater, surface water, or leachate 5 samples, Dioxins and furans 8290A or 1613B Groundwater, surface water, or leachate 5 sample
Start-up Nutraceutical company in the process of sourcing raw material for supplements needs laboratory for vendor qualification testing to test samples from potential vendors. We are looking to do purity tests for 1-2 samples of each of the following ingredient: folic acid, zinc, magnesium, DHA, Vitamin B3, Vitamin B6, Vitamin C, Vitamin D, Caffeine, Taurine, L-theanine.
LONG TERM TESTING Analytical Chemistry Laboratory needed for periodically quality control testing silica gel prior to procurement of large quantities to strict quality standards. Material : SILICAL ? SORBEAD ?R? Parameters: 1. Chemical composition 2. Shape 3. Color 4. Bead size 5. Pore diameter 6. Pore volume 7. Specific surface area 8. Bulk density 9. Specific Heat 10. Attrition Loss 11. Expected life 12. Crushing Strength 13. Pressure drop 14. Achieved dew point 15. Static Adsorption ar 10%,20%,20%60%,80% RH 16. pH value 17. Reactivation/Regeneration Temperature 18. Water Resistant
Microbiology laboratory to provide a quote for microbiology testing: kill test against S. aureus.
Brief background Incoming test material: colloidal silver solution (~0.014-0.016 mg/ml)
Preparation of test sample: 1) Confirm concentration 2) Concentrate sample to 0.3 mg/ml
Concentration and time points: 1) Range for testing: 0.3 mg/ml, 0.15 mg/ml, 0.075 mg/ml, 0.01875 mg/ml, 0.01875 mg/ml 2) Time points: 0.5, 1, 3, 6 minutes (or based on protocol)
Automotive laboratory needed for ASTM Testing and testing to norm MS211-47 Type A2 (KIA/HIUNDAI): ASTM D792, Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement , density, relative density, specific gravity, D638 - 14 Standard Test Method for Tensile Properties of Plastics , modulus of elasticity, percent elongation, plastics, Poisson&rsquo,s Ratio, tensile properties ASTM D790, Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials , flexural properties ASTM D256, Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics , impact resistance, Izod impact, notch sensitivity, notched . ASTM D648, Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise
Polymer Materials laboratory needed to conduct isothermal viscosity testing of sealants and estimate working life at various temperatures. I know this cannot done by regular Brookefield viscometers. At 75 F for 2 hours at 85 F for 2 hours 100 F for two hours 120 F for 2 hours 135 F for 2 hours 150 F for 2 hours.
Marble quarry need laboratory for ANSI testing of 4 products. Quarry makes marble blocks, as raw material in order to produce high quality building materials of ready mixed mortars, tile adhesives, waterproofing materials, additives and amplifying fluids. o increase our export possibilities we have chosen the 4 following adhesives and joint grout products for testing under the ANSI standards (Standard and optional performance characteristic). ? tile and marble adhesive, tile and marble adhesive, tile and marble adhesive, Colorfill, Joint grout, 2-8 mm, for tiles and slabs, ceramic or natural stone. Please inform us about the cost, payment terms and all the details and the accompanying documents that are necessary to send the test samples such as packaging, quantity of the sample, testing time
URGENT Materials laboratory needed for physical and microbiology ASTM testing of tape bituminous wrapping tape used in petroleum pipelines Property Values Test method Tensile strength 12 N/mm2 BS 2782 Elongation 300 ASTM D 1000 Tear resistance >50 ASTM D1004 Adhesion to steel >2 ASTM D1000 Adhesion to Self >1.8 ASTM D 1000 Impact resistance >15J DIN30627 Dielectric strength >30000 total systemASTM D149 Insulation resistance2.5x1012 Ohm.cm ASTM D257 Water Absorption <0.1% ISO 62 Water permeability 0.01g/100inch2/24h ASTM F1249 Bacterial Growth - No Mic
LONG-TERM QUALITY CONTROL TESTING: Large cosmetics company needs contract lab that can perform XRF (X-Ray Fluorescence) testing. The testing would be performed as part of an Identification test on incoming raw material receipts. The test would be qualitative only (not quantitative) to detect the presence of various elements such as Fe, Mg, S, Al, Si, Zn, or Ti. I have specifications that specify exactly which element(s) to test for each sample. Usually 1-2 elements per sample. I have a test method that gives more specifics if needed. Anticipated sample volume is approximately 10 per week. Thank you.
Marble quarry need laboratory for ANSI testing of 4 products. Quarry makes marble blocks, as raw material in order to produce high quality building materials of ready mixed mortars, tile adhesives, waterproofing materials, additives and amplifying fluids. o increase our export possibilities we have chosen the 4 following products for testing under the ANSI standards (Standard and optional performance characteristic). ? FLS 1000, tile and marble adhesive, C2TE S1 ? GM 1, tile and marble adhesive, C2T ? FK 10W, tile and marble adhesive, C1T ? Colorfill, Joint grout, 2-8 mm, for tiles and slabs, ceramic or natural stone, CG2 Please inform us about the cost, payment terms and all the details and the accompanying documents that are necessary to send the test samples such as packaging, quantity of the sample, testing time
Geology laboratory needed for geophysical testing: Size, abrasive index, moisture content, bulk density, gradation
These tests need to be done on limestone and gypsum rock samples.
Materials laboratory needed for physical testing of machine part that has Sulphuric Anodization on Aluminium that require following testing.
a. Insulation of the oxide coating (Disruptive voltage test) b. Sealing quality ? to measure loss of the absorptivity of the anodic oxide coating c. Continuity of oxide coating d. Light resistance test
Pharmaceutical analytical chemistry labroatory needed for new OTC drug product development of 70% Isopropyl alcohol USP and 3% Hydrogen peroxide USP Sprays and USP testing of raw material for 70% isopropyl alcohol USP and 3% Hydrogen peroxide USP.
Also looking for an services for Like what klnd of testing requries.
Materials laboratory needed for ASTM boat cleaner testing on fiberglass and wood to determine it is effective and non-harmful in cleaning grease, oil, gas, scum and marine growth from boat hulls that comprise of fiberglass and wood and will not harm the surface as well. Our product is biodegradable and safe for the environment.
Russia Materials Laboratory needed for ASTM Testing for determination of iodine adsorption - ASTM D1510-13 The lab must be accredited by a single national accreditation system. The lab must be provided with equipment in accordance with the methods described in ASTM
UK cosmetics laboratory needed for full quality control testing and analyses needed for the soap industry including all raw materials (oil, water...) and finished products to to assure that the soap production is controlled and meet the EU standards and regulations
Performance laboratory needed to conduct comparison test study betwee light curing adhesives activated by UV lights.
The side by side tests we would like to complete include:
Curing Plastic onto Plastic Curing Plastic to Glass Curing Metal to Plastic Curing Wood to Plastic
We would like to know, for each product, how many pounds of force it takes to break the bond, for each material combination above.
Also, we would like to test overall brightness of both UV lights in mW.
Please let me know cost to complete. We would hope to complete the test by the end of this week.
Fittings company needs India analytical chemistry laboratory for raw material testing: Spectro (Chemical Analysis,) Micro, Mechanical,sand testing( No-Bake and Green sand) and in-coming raw materials testing etc.
Certified Materials Laboratory needed for coating testing of Three (3) mixed adhesive coating samples tested for the following: 1. Volatile Organic Compounds (VOC) content per ASTM D-3960, Section 8.2.4. (Determining Volatile Organic Content of Paints & Related Coatings) and/or SCAQMD Annex to ASTM D-3960) 2. Weight Fraction of non-volatiles (solids) per ASTM D-2369-81 (Volatile Content of Coatings). 3. Density of coating per ASTM D-1475 (Density of Paint, Varnishes, Lacquer, and Related Products).
India Materials Laboratory needed to provide a quote of rates for testing shear strength Flatwise of Fabric base Phenolic sheet as per Bureau of Indian Standard, BIS 2036 Phenol Sheets
Europe Packaging laboratory needed for UN Certification drop testing on a new bag material that holds our product, packaging group 2 4.2 self heating solid.
2 types of bags to be evaluated.
Urgency: Within the next Month
Materials Laboratory needed for Formulation and testing of flame retardant epoxy and unsaturated polyester compositions using customer supplied additives.
Preclinical Bioanalytical Laboratory needed for protein analysis by C2C12 assay for osteoinductivity. The material being tested is a bone morphogenetic protein compound. Two preclinical studies.
ISO Materials laboratory needed for ASTM PMMA panel testing to US Standards, ISO and EN standards. ASTM E90 and E413, ASTM D-638 : tensile properties, ASTM D-790 : flexural properties, ASTM D-1003 : luminous transmittance, ASTM D-635 : burninjg of plastic, ASTM D-1929 ignition temperature. We also need to do the TL-4 inside the Report 350 (crash test safety performance). Thank you so much. Regards.
Technology Laboratory needed for new panel design tests including theArc Resistant testsWe also need a Arc resistant test for a MCC, but for this MCC we already have the certifications for design tests. What information do you need to inform me the commercial conditions for these tests? Scope: 1 ) Design test for MV Metal Clad panel- tests According to IEEE C37.20.2-2015 6.2.1 Dielectric tests 188.8.131.52 Power frequency withstand tests 184.108.40.206 Lightning impulse withstand tests 220.127.116.11 Test for bus-bar insulation, bus joint insulation, and bus tap insulation 6.2.2 Rated continuous current tests 6.2.3 Momentary withstand current tests 6.2.4 Short-time withstand current tests 6.2.5 Auxiliary equipment primary disconnecting device momentary current withstand test 6.2.6 Mechanical endurance tests 6.2.7 Tests for insulating materials 6.2.8 Coating
Contract bioanalytical lab needed to form a long-standing relationship for antibody production, ELISA, and neutralization testing for a synthetic peptide vaccine. Vaccine does not contain any viral material. We look forward to hearing from you!
USA Materials Laboratory needed for Density testing according to ASTM D1505, Standard Test Method for Density of Plastics by the Density-Gradient Technique. Please provide me the following information:
1. standard & rush turn around time & fee 2. price 3. sample amount 4. Quality System (ISO 9001, GMP, GLP?)
Food Laboratory needed to assist engineering company on project to determine the purity of a Parmesan Shredded cheese product. We are looking to determine the percentage of non-Parmesan cheese constituents in the product. These may include Cellulose, other fiber based materials, as well as other cheese species.
Jewelry manufacturer of gold or rhodium plated fashion jewelry over brass needs US Materials laboratory for material composition testing and plating thickness testing of these pieces.
Materials laboratory needed for DIN Testing of one rubber compound sample for testing: 1. DIN 53505 2. DIN 53507 3. VDA 675205 4. VDA 675303 5. VDA 675217
FDA / GMP laboratory needed for nutraceutical testing to ensure raw materials listed on the box are the only items in the finished product.
Europe Packaging laboratory needed for UN Certification drop testing on a new bag material that holds our product, a biomass powder containing DHA oil for animal feed supplementation.
Bioanalytical laboratory needed for protein analysis to test lactate levels in a hydrolyzed protein material
Materials Laboratory needed for ASTM Testing of Single coated tape testing for adhesion Per ASTM D3330 or PSTC 101 using 180 degree peel on polypropylene. Value to be reported in the VALLEY (lowest adhesion result) per sample. Will provide 20 samples in total, 10 now and 10 in two weeks.
Biophysical Laboratory needed for ISO Testing of medical implant. The material is Metal. It is to ensure that the design does not fail under standardized conditions for example ISO 9585:1990, Implants for surgery Determination of bending strength and stiffness of bone plates
Materials laboratory needed to provide a quuote for radioactivity testing on one solid sample of an epoxy coating
Canada Analytical Chemistry Laboratory needed for confirmation testing. Test a sample of Lactic Acid 80% and verify that it is the exact same material as the CoA, Certificate of Analysis. Looking forward to your response. Thank you in advance
Geology company needs India environmental laboratory for soil and sediment testing: the stream sediment and soil samples are needed to test for multi-elemental chemical analysis in connection with preparation of certified reference materials. the samples are collected from different parts of India
Materials Laboratory needed for ASTM Testing to ASTM E-84, Standard Test Method for Surface Burning Characteristics of Building Materials
Medicinal chemistry laboratory needed for testing plant materials to determine the active ingredients for potential medicinal use or Chemical characterization of bioactive constituents.
The chemical characterization of plant raw materials is to find out any major or bioactive constitutes/phytochemicals, particularly major components or bioactive components, such as flavonoids, terpenoids, phenols, saponins, coumarins, and alkaloids.
India Materials Laboratory needed for glove testing for ANSI ASTM F1790: Level 4 certification for our gloves.
Microbiology laboratory needed for medical fabric testing for bacteria-resistance. It is nylon taffeta 70 denier with a pic waterproof backing. The same material used for mattress liners in hospital and nursing home settings. I m looking to getting more information s to what types of testing you would do, what certificates can be granted, and an estimate to the cost for these services.
Materials Laboratory needed for ASTM Testing: ASTM Closed cup flash point test (Tag or Martens, etc.) on a thin liquid material. Estimated FP is 140 F. One sample will probably suffice.
Automotive Laboratory needed to conduct tests according to General Motors standards: GMW: 3205 - Odor , 3232-Flammability , 3235-Foggong , 3259-Mildew growth , 15634-Interior Emissions , 15063-Material Sepc.
India Materials Laboratory needed for ISO Testing to ISO-105-DO2, Textiles Tests for colour fastness Part D02: Colour fastness to rubbing: Organic solvents
Materials Laboratory needed for impurities testing: the impurity, or impurities, we are removing from a crude monomer with an aluminum oxide column. H NMR does not provide a complete picture for this determination as it may possibly be an inorganic substance. How much would it cost to analyze 3 samples (neat and 2 purified) via atomic absorption? T
Materials Laboratory needed for Thermogravimetric Analysis TGA and Dilatometry on YSZ - YttrIa Stabilized Zirconia (powder) used for ceramic processing. Dilatometry (DIL 402 preferred) Thermogravimetric Analysis TGA (RT-1450C) in air in 1450C in powder form but may want pellet form.
USA Materials laboratory needed for ASTM Testing for melt point determination to ASTM D789, and dimensional stability. My sample is type 66 molybdenum disulfide-filled nylon. Could you provide me the following:
1. Pricing 2. Standard and rush turn around time, and its fee.
Southern USA FDA GMP compliant Pharmaceutical Laboratory needed for raw material , API and final product release testing for Small Volume injectable, generic finished drug products with validated test methods..
STABILITY - FDA GMP Pharmaceutical Laboratory needed for (QC) Quality Control testing of finished product (transdermal patch), raw material release testing, ICH stability testing by qualified/validated analytical methods.
Eye wear company imports eyeglass frames from Italy and would like FDA GMP laboratory for certification testing that frames are made from FDA approved raw materials.
Materials Laboratory needed for biodegradability testing of lab that an antifoam to determine if it is biodegradeable.
USA Materials Laboratory needed for ASTM Testing: gel content of polyethylene samples using ASTM D2765-11, Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics (xylene or Decalin extraction, boiling solvent, sample in wire mesh cage, weight loss after 6-12 hours in boiling solvent, then vacuum oven).
Medical Device Company needs laboratory to provide quote for testing of DEHP, Latex and Phthalates on catheter. Catheter is composed from various materials: Gray Pellethane - proximal hub, Yellow - pellethane - body, Air valves - PVC, Blue & yellow Pebax - distal end, Grey Pebax - distal hub.
Third-Party Laboratory needed for shoe testing to American Podiatric Medical Association's Seal of Acceptance for children's shoe lines. The APMA requires that we submit our shoes to third-party lab tests to establish the product?s safety (including a Material Safety Data Sheet and EPA/FDA approval documents where applicable), as well as other health-related properties, such as the product being lightweight, very flexible, and slip-resistant.
Design and Engineering company needed laboratory for sandwich panel testing:
1) Test Sample :- Aluminum Honeycomb Sandwicu Panel 2) Material :- 1) Aluminum Sheet 2) Honeycomb Core (Alu) 3) Adhesive Glue 3) Test Parameter :- 1) AGING (Specification -ISO 9142 - D3 - 21 CICLI) 2) SHEAR STRENGHT (L-direction) (Spec-DIN 53294) 3) SHEAR MODULE (L-direction) 4) SHEAR STRENGHT (W-direction) 5)SHEAR MODULE (W-direction)
Microbiology laboratory needed for pyrogen testing for a medical device and components. the active ingredient is photosensitive and testing under yellow lighting would be required. None of the materials used in the device have radioactive properties
India NABL accredited laboratory needed for abs and san plastic product materials testing
North America Materials Laboratory needed for Migration test of Bisphenol A BPA and other possible constituents under 21 CFR 175.300 (d) table 1
Materials laboratory needed for Thermal Conductivity testing of DIN EN ISO 8497 for our rubber insulation
USA bioanalytical and microbiology labroatory needed for material containing Human Serum Albumin testing for Mycoplasma Bacteria & Fungi (Sterility) Bacterial & Fungal Stasis Specific Gravity
University Scientific researcher needs a Middle East laboratory for conducting science experiments on fuel cells including preparation and characterization of cathode materials based oxides and thin layer of doped and undoped by chemical and electrochemical method for fuel cells, for a thesis entitled: synthesis and characterization of the doped and undoped ceria electrochemically.
USA Environmental laboratory needed that can perform this method, EPA 1664, Rev A N-Hexane Extractable Material by extraction and gravimetry. My sample is waste water.
URGENT Los Angeles Materials laboratory needed for material composition for a textile type material. Validation that its leather.
India materials laboratory needed to perform Tests required for Material of Gland Packing. Glass Ply OR Carbon Fibre Ply, Silicon OR Made of Ceramic Fibre. FT - IR Analysis require.
Food Laboratory needed to provide a complete quotation for heavy metal analysis in food for 4 elements (As,Cd Pb and Hg) in food materials
Materials laboratory needed for IEC electrostatic testing of polyethylene sheet to to IEC 61340-4-4, Electrostatics standard for its electrostatic properties.
Industrial milk company needs Eastern Europe agriculture laboratory needed for roughage testing and manure testing. What is the price and conditions of testing? What are your testing parameters? What the minimum amount of material and packaging is necessary for research sample?
Materials laboratory needed for f PROPYLENE GLYCOLtesting for appearance, PG content, moisture, density, index of refraction, acidity, distillation range, color (Pt ? Co).Please provide the price of this analysis? What the minimum amount of material and packaging is necessary for research sample?
Materials Laboratory needed that performs ASTM D6703, Standard Test Method for Automated Heithaus Titrimetry
Large piping company needs East Coast North America materials laboratory for ASTM Testing of six o-ring elastomer samples for DMA analysis to measure Glass Transition Temperature (tg values) following ASTM E 1640. Basically I need to dynamically compress the samples at starting temperature of -70 C with 1 hz frequency up to 60 C with 2 c/min heating rate.
Materials laboratory needed that is capable of running Alberta Transportation Specification B388 tests for type 3 concrete sealers
Materials Laboratory needed for ASTM Testing of hdpe/pp woven grocery bags from used hdpe/pp woven sacks including peel testing as per ASTM F88 & F2824; creep test as per ASTM F1140 & F2054;tensile testing/hermetic seal/plastic bag/shrink wrap plastic welding etc. etc.
Materials laboratory needed for Residual Gas Analysis, Raman Spectroscopy or Electron Spectroscopy for Chemical Analysis on our test parts. The sizes of the residues are typically 0.20 mm x 0.40 mm for studying the long-term effects of potential out-gassing of epoxies on the lifetime properties of modules. First trace chemical analysis provider showed that the residues are not inorganic molecules, but they were not set up to delve any deeper.
Materials Laboratory needed for film testing of a film structure for testing outgassing and refractory Components.
Materials Laboratory needed for microelectronics testing for collected volatile condensable materials and Total Mass Loss
Materials Laboratory needed for analysis for total chlorine content on DVB-Styrene crosslinking gel samples.
Medical Device Laboratory needed for EUropean Pharmacopeia Testing of Surgical threads to European Pharmacopeia [8.0] Monograph 01:2008:0324, IDENTIFICATION For (Silk sutures) Identification of silk: A. Dissect the end of a suture, using a needle or fine tweezers, to isolate a few individual fibres. The fibres are sometimes marked with very fine longitudinal striations parallel to the axis of the suture. Examined under a microscope, a cross-section is more or less triangular to semi-circular, with rounded edges and without a lumen. B. Impregnate isolated fibres with iodinated potassium iodide solution R. The fibres are coloured pale yellow. For UNILIN (Linen Sutures). Identification of linen A. Dissect the end of a suture, using a needle or fine tweezers, to isolate a few individual fibres. Examined under a microscope, the fibres are se
California packaging laboratory needed for beverage packaging testing of new beverage formulation (given in small dosages e.g. 30 ml i.e. shot). My formulation does not include preservatives. I would like to test the formulation to see which packaging material will be the best.
India Materials laboratory needed to provide quotation for astm e 84 testing charges of composite material
Chennai Materials Laboratory needed to measure the flank wear of a drill bit using a scanning electron microscope. Require to measure the flank wear and surface roughness of a drilled composite material
Healthcare company needs polymer laboratory for materials testing of Polytetrafluoroethylene PTFE membrane for alkalinity as per 40 CFR part 50 Appendix L
US or UK geology laboratory needed for lime analysis for SiO2, R2O3, MgO, CaO, LOI, Sulfur.. Please send the quotations for Quicklime and Hydrated lime analysis. Material to be tested through XRD/Chemical analysis.
India geology laboratory needed for quicklime and hydrated lime analysis. Material to be tested through XRD/ Chemical analysis. Parameters to be tested are: SiO2, R2O3, CaO, MgO, Loss of Ingtion, Sulfur. Please send quote for analysis.
INdia materials laboratory needed for Carbon Residual Test As Per EN 723 For Brass And Copper Tubes
Engine manufacturer needs India material laboratory for epoxy testing: Thermal Coefficient of Linear & Volumetric Expansion of Epoxy after getting Hardened. 5 samples
Certification laboratory needed for Industrial Fabrics Association International for flame-resistant material CPAI - 84 on a tent
India analytical chemistry laboratory needed for deformulation of an ointment for Material List (Recommended ingredient inside the liquid)
Materials laboratory needed for analysis for kitchen paper and wet towel, (analysis such as paraben, alcohol, eligibility for health, migration, recycle ratio...) Please provide price and turn-around time
Paint manufacturer needs Materials laboratory for IS or ASTMTesting 500 Kg jumbo bags (FIBC) to be tested for specification parameters as per the standards applicable to them.Please let us know the IS or ASTM Standards relevant to Kg jumbo bags.
Europe accredited laboratory needed with accreditation for the scope of the test method in accordance with
- EN 13500 - Thermal insulation products for buildings. External thermal insulation composite systems (ETICS) based on mineral wool. Specification - Sample to be tested: Plastic - Qty: 4 Please send sample size required and turnaround time expected.
For further information, please feel free to contact me. Your prompt support would highly appreciate.
Materials laboratory needed for IS or ASTM Testing of bags purchased from vendor: FIBC of 500 Kg capacity made up of HDPE to be tested for Elongation and breaking strength as per the IS or ASTM Standards applicable
University researcher needs India Materials Laboratory for ASTM Testing to ASTM D445 ASTM D93-94 ASTM D5453-93 ASTM D524 ASTM D482-91 ASTM D2015-85 GAS CHROMATOGRAPHY ASTM D4052-91 AOCS CD1-25 AOCS CD3 ASTM D2500-91 ASTM D97-93 ASTM D613 Kinematic viscosity Flash Point Sulphur Carbon Residue Ash content Higher Heating Value Fatty acid profile Density Iodine value, Saponification Value Cloud point Pour Point Cetane No. Fat content
Large oil company needs materials laboratory to perform Soil Cleaning Test by FED-STD-791 Method, 7502. Testing to be done on an isoparrafinic solvent with flash point ~ 220F.
Southeast USA electrical laboratory needed for electrical control panel testing of installed a conveyor system (brand hytrol), with 3 electrical control panels the individual components in the panel box are all ul listed but the panel box is not we need a certificate for our final inspection that requires the box to be safe
Materials Laboratory needed for Oil Flashpoint Testing to ASTM d93, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Testerflash point
Materials laboratory needed for ASTM flexible laminate testing to check the WVTR and UV transmission rate to ASTM F1249. If yes, please provide the details of sample size, cost, time period..etc.
URGENT United States Materials Laboratory needed for DBL 5404 Odour Test for PPT40 Grade Resin... Please provide cost of this test ASAP.
Materials laboratory needed for ASTM Testing of laundry additives to ASTM 2274 Standard Test Method for Oxidation Stability of Distillate Fuel Oil
Our formulation consists of coated gelatin size 0 capsules (methacrylate polymer/enteric coating). I would like this coating characterized for homogeneity in polymer material and thickness across the complete capsule. (Raman, Terahertz, etc.)
Manufacturer needs Consumer Products Safety Toxicology Laboratory for product safety and toxicology testing of fabric-based product.for
- Cytotoxicity testing. - Sensitization testing. - Irritation or Intracutaneous Reactivity Testing - Specific testing on Urethane materials: 0 mmHg for 3s to 150 mmHg and hold for 3s for a minimum of 100,000 cycles.
Materials laboratory needed for ASTM testing of roof coating to ASTM D 6083Standard Specification for Liquid Applied Acrylic Coating Used in Roofing or to ASTM C 1549 or ASTM E 1918
Materials Laboratory needed for ASTM Testing of paint and coating to ASTM D7855, Standard Test Method for Determination of Mold Growth on Coated Building Products Designed for Interior Applications Using an Environmental Chamber and Indirect Inoculation
Materials laboratory needed for Fabric Testing required for anti radar on fabric used for camouflage nets as per MIL/BS standards.
Materials laboratory needed for ASTM Testing: Abrasive resistance test on our Abs Glass filled material as per ASTM D 1044. Please specify testing feasibility and time duration and quote to proceed further .at earliest.
Immediate replay on this will be highly appreciated and looking forward
Preclinical Laboratory needed for Biocompatibility Study for implant material SS 316L as per ISO 10993 , Biological evaluation of medical devices
Materials Laboratory needed for ASTM E84, Standard Test Method for Surface Burning Characteristics of Building Materials Lab testing quote for Flame Spread. One sample
Materials Laboratory needed forISO footwear testing: abrasion test on footwear outer soles based on International Organization for Standardization test method 20871, which is an abrasion resistance test intended for all outer soles irrespective of material? If so, is your lab performing this test located in the United States?
India materials laboratory needed for coatings testing: 1. Polyester Fabric PU Coating Test. 2. Polyester Fabric PVC Coating Test.
UK Pharmaceutical Laboratory needed for turbidity and particulate matter testing of a freeze-dried cytotoxic pharmaceutical material. 9 vials to be tested. Vials tio be reconstituted and tested for turbidity and particulate matter (suspected silicon oil contamination)
Environmental simulation laboratory needed for accelerated simulation testing that simulates ocean shipping environmental conditions experienced shipping from Asia to us on the ocean. The material is a molded EVA that I need to understand dimensional stability before and after the shipment process. Please reply with contacts who could provide this in an accelerated manner. South east Asia based would be good. Thanks tom
FDA polymer materials laboratory needed for FDA compliance testing for resinous and polymeric coatings FDA Title 21 Section 175.300. Under (a) - (2) Coatings cured by polymerization, condensation, and/or cross-linking without oxidation.
Electrical laboratory needed for materials characterization for characterizing a commercial coaxialspecialty cableliterature.Resistance, loop resistance, capacitance, inductance, voltage rating, propagation velocity, shield coverage, operating temperature range.
Packaging laboratory needed for Food Packaging testing to comply with EU food Packaging requlations. We make a water based coating that can be alternative replacement for PE, PP, PET or CPET plastic films or plastic materials. Need to have microwave heating testing and high temp ovenability ratings for coated paper board packaging products. Would prefer a Euro based lab for familiarity with EU food packaging regulations and compliance. May nee extractives testing done.
FDA GMP Polymer Laboratory needed for GMP Raw Material Testing: Polymer Testing for Melt Flow for High-density polyethylene HDPE
Materials laboratory needed for testing mixture of rosin, beeswax and activated charcoal heated on a open flame to determine malleability and ability to be cast into shapes at low temperatures
Tyre manufacturer needs rubber testing of natural & synthetic rubbers,carbon black,silica SiO2,sulfur,zinc oxide,stearic acid,process oils,micro wax,rubber chemicals(accelerators,antidegrading materials,steel wires etc.
Physical Laboratory needed which has an accreditation for the scope of the test methods in accordance with IEC 60754-1 - Test on gases evolved during combustion of materials from cables for raw material of Silicon electric wire. I would appreciate if you could send me a ROM quote including sample size and turnaround.
Materials Contract Test Laboratory needed for ASTM / or ISO Cloud Point Testing of 9MOL(nonyl phenol exoxylate) to ISO 3015:1992 and/or ASTMD2500
EPA LEED, USGBS Environmental Laboratory needed for Formaldehyde Testing in building products. Laminate truss, urethane foam adhesive, wallboard, blown in fiberglass insulation Looking for off gas rates and comparison with accepted limits vis a vis EPA, LEED, USGBC, and the like.
Nanotechnology laboratory needed for blending 5ml containers of nanoparticle and polymer blends . Please provide costs for a batch of 1 L of the material? They need to be measured and mixed in a centrifugal mixer.
EU or USA Food Safety Laboratory needed for Food Contact Materials FCM safety testing of silicone baking tray to see if it meets EU and/or FDA regulation standards on FCM safety. We buy in the trays from China and want to ensure they are compliant with the regulations. They are sold to customers and used in a domestic environment.
Physical Laboratory needed to perform Salt Spray (fog) test for PTFE coated bolts (Fastener) as per ASTM B117
Materials laboratory needed for LEED and ASTM color testing of color supplied to the decorative cement market: 40 colors tested torASTM E 1980 to obtain the Solar Reflectance Index. This would be to comply with LEED 7.1 Urban Heat Island effect
USA Pharmaceutical analytical chemistry laboratory needed for USP testing on raw materials - Sodium Fluoride, USP (Identification A, Heavy Metals, Fluosicilate, & Acidity/Alkalinity) & Cetylpyridinium Chloride, USP (residual solvents).
Materials laboratory needed for Biodegradability testing to determine if liquid cleaning product is readily or ultimate biodegradable with percentage
North America Geology Laboratory needed for Trace level analysis of As and Pb in fine grind nepheline syenite samples and low purity quartz materials
Apparel importer needs textiles laboratory for materials testing of waist trainer corsets: Style and compositiontesting on care label is
7023 latex 100% inner lining 96% cotton 4% elastano the outer lining is made of 90% Nylon and 10% elastan both lining glue to latex
ISO 17025 Materials Laboratory needed for paint testing to VW Standard VW TL211 Table 2 section 1.3 Evaluation of effect paints in terms of differences in sparkling and graininess per VW 5019 & 1.4. Structure measurement system: wave-scan plus?
Plastics Materials Laboratory needed for Polytetrafluoroethylene PTFE Testing of PTFE UV transmittance in the 250 - 260 nm range Objective: To establish the % transmittance of a PTFE sample of : 1) 0.50 mm thick; Sample size = 1. 2) 0.30 mm thick; Sample size = 1. 3) 0.10 mm thick; Sample size = 1.
Deliverable: A 1-to-2 page report in electronic format. The report should include methods and results. The results to be presented in a graph as wavelength vs. % transmittance
USA Materials Laboratory needed for ASTM Testing of Adhesion of Solid Film Lubricants to MCL F-23 and ASTM D2510-94
Analytical Chemistry Laboratory needed for Boron materials Testing with a purity in the range of 99% (1% are impurities, 99% is amorphous boron). On such material the testing laboratory should verify the actual purity percentage and the chemical composition of the impurities; for each impurity the result should include the amount found. A typical output would be a table including all impurities and, for each item, the quantity found in respect to the total quantity of boron tested.
Is your testing facility able to reliably analyse such material? If you have the capability, how much would it cost each test result? And what would be the lead time to complete a single test?
Materials Laboratory needed for Constituent components testing of oil product generated from pyrolysis of scrap tires. Need to know all components and percentage by weight or volume.
Contract Lab needed for valve testing for Leakage; Hydrostatic Strength; Maximum Flow Shut-off; Strength(bending moment, turning effort, impact); Continued Operation; Corrosion test; Marking Material Adhesion and Legibility.Tests according ANSI 4.6 - MANUALLY OPERATED VALVES FOR NATURAL GAS DISPENSING SYSTEMS)
Materials Laboratory needed for ASTM Testing of Erucamide slip counts in polyethylene pellets to ASTM D6953, Standard Test Method for Determination of Antioxidants and Erucamide Slip Additives in Polyethylene Using Liquid Chromatography (LC) or other test methods
University Researchers need Asia sensory laboratory for slow release fragrance technology testing for markets in Asia.
ISO 17025 or FDA GLP Accredited Test institute needed for catheter and catheter accessory biocompatiability testing of these materials according to related standards to Test Standard: 10993-1. We will focus on products which will stay more than 30 days in body. 2. nd product: Implantable Gel material Please give me price and make me informed about the procedure and accreditation status
Pharmaceutical laboratory needed for consistency testing by penetrometry as per PhEur 2.9.9, the test material is topical ointment. The assay needs to be modified slightly in that the ointment must be gently taken from cut open tube and carefully transferred into the test cup to minimize shear to the ointment which changes the results.
University Researcher needs India materials laboratory for NiTi thin films of thickness 300 nm on silicon wafer size 1 cm x 1 cm. I need to characterize these samples using TEM. Please send the quotation.
South Africa Physical Chemistry Laboratory needed for Particle Size Distribution (PSD) testing of screened material for Performance Testing a vibrating screen. The material is Iron Ore sinter from the Arcelor Mittal VDB works. Maximum Material size:- -30mm Sinter, Minimum Material size:- Dust. A percentage per particle report would be required. We would like to know what it would cost per sample and how much material would each sample be required to be. Our total requirement would be for 100 samples that would be collected over a 24 hr period during the middle of next week, 9 - 13 Nov.
Materials laboratory needed for OECD biodegradability testing of aluminum complex greases to OECD 201-204, OECD 107 or 117, and OECD 301B. Please include pricing.
Materials laboratory needed for tape certification testing to a specific military requirement. A-A-59341, COMMERCIAL ITEM DESCRIPTION: TAPE, TWO SIDE PRESSURE SENSITIVE ADHESIVE, FLEXIBLE FOAM BASE (FOR USE WITH EXPLOSIVES) (29-SEP-1998) [SUPERSEDING MIL-T-60394A]., This CID covers the general requirements for a double coated flexible foam pressure sensitive adhesive tape in roll form wound on a core with a release liner. The tape shall consist of a high density open or closed cell foam plastic carrier, coated on the top and bottom surfaces with a smooth, uniform, homogeneous layer of pressure-sensitive adhesive. The tape shall be in roll form, wound on a core of sufficient strength to prevent roll distortion from shipping, handling and use conditions. The tape shall have a release liner to facilitate dispensing and applying the tape.
United Arab Emirates Materials Laboratoryneeded for ASTM Testing: ASTM G180 test for Corrosion inhibiting admixtures for steel in concrete by polarization resistance in cementitious slurries.