Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Electronics Laboratories to perform their Electronics Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Electronics laboratory that would like more information on these Electronics projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Electrical laboratory needed for electrical certification and acceptance testing of transformers, arresters, and switches including:
Current transformers 72.5KV and 145KV MR 200-400-600-800-1000-1200/1/11/5 ; Surge arrester 72.5 and 145 KV ; Central opening switch 72.5KV and 145 KV, 3150 Amp, Voltage transformer 72.5KV and 145KV, Power switch tanks monopolar live tension for 145KV SF6 gas insulated ; Power switch tanks tripolar for dead tension 72.5Kv and 145KV SF6 insulated.All the material is supplied by one facotry located in Xian, China.
ISO 17025 certified laboratory needed for OECD physical / chemical testing of solid materials and an octanol / water solution as per three OECD standard methods: OECD107 Partition Coefficient (n-octanol/water): shake flask method , OECD 117 Partition Coefficient (n-octanol/water), HPLC method, and OECD123 Partition Coefficient (1-octanol/water): slow-stirring method
Large company needs laboratory for UL Tilt Test - UL certification for custom kiosks means the stability of the units. These tests are known as the slide test, force stability test and 10 degree status tip static tip stability test. The tests are baselined against the normal 5 year old child. The usual precaution is if the unit is subject to a push force of 9Kg in any direction.
Environmental simulation laboratory needed for UV weathering testing on equipment in compliance with IEC 60068-2-5:2010 Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing, with test parameters according to:
- Test procedure: C
- Test temperature: 40 °C
- Test duration: 240 h
- IP69K rating (DIN 40050-9 standard extending the IEC 60529)
- ENV 008C chemical testing
Large cabling company needs a laboratory for fire resistance cable testing to BS 6387 Cat C W & Z.
1) Copper conductor, Mica tape, XLPE insulation, LSHF Bedding, Galvanized SWA and LSHF final Sheath.
3) Copper conductor, Mica tape, XLPE insulation, LSHF Bedding, AWA and LSHF final Sheath. This cables will be tested as per ( BS 6387 Cat C W & Z ).
Electrical laboratory needed for ASTM & IEC Testing of ground enhancing compound to IEC 62561 Lightning protection system components 1. Leaching test - Based on EN12457 - 2 Part 2 and EN - 12506 2. Sulfur test - Based on ISO 4689-3 : 2004 3. Determination of resistivity : ASTM G57-06 4. Corrosion test - Based on LPR method (Linear Polarization Resistance Method)
Research laboratory needed for optimization study on ozonators used for water treatment to define the optimal ozone amount for treatment of customer's water including chemical analysis of water to calculate how much ozone we need to decrease quantity of needless organic and inorganic compounds to acceptable level.
Computer Hardware company needs certification laboratory for ETSI certification testing an e-CALL modem according to multiple ETSI standards including 1) ETSI TS 102 936-1 and ETSI TS 102 936-2, 2) ETSI TS 122 011 and ETSI TS 123 122, 3) ETSI TS 134 123-1 (Clause 6), 4) ETSI TS 122 101 5) ETSI TS 126 269 6) EN 16062:2015
Industrial Third-Party ISO 17025 Laboratory needed for IEEE, ANSI and UL Testing of 9 cables flammability and toxicity testing: FT4/IEE1202 flame propagation test and ANSI/UL1685 smoke release test, and BSS7239 toxicity test, please let me know the cable length for testing, quotation and lead time, thanks.
Europe electrical laboratory needed for IEC tests on fibreoptic cables according to IEC IEC 60793-xx and 60794-xx standards: Testing fibreoptic cables on tensile performance, abrasion resistance, crush, impact, bending, kink, temperature cycling, water penetration, attenuation, PMD, chromatic dispersion, fire resistance, according to IEC Standard 60793-xx and 60794-xx. Following tests are required: IEC 60793-1-40 IEC 60793-1-48 IEC 60793-1-42 IEC 60794-1-2-G7 IEC 60794-1-2-E3 IEC 60794-1-2-G1 IEC 60794-1-2-E1B IEC 60794-1-2-E2B method 1 IEC 60794-1-2-E3 IEC 60794-1-2-E4 IEC 60794-1-2-E6 IEC 60794-1-2-E7 IEC 60794-1-2-E10 IEC 60794-1-2-E10 IEC 60794-1-2-F1 IEC 60794-1-2-F5B
Independent laboratory needed for LED comparison study of 4 manufacturer's underwater LED light components to evaluate Quality of construction ? Quality of LED components ? Quality of LED Drivers ? Color Temperature output from each ? Lumens output from each- Underwater Lumens from each ? Projected beam angles from each ? Thermal temperature from each - Are the LED?s in spec with required approvals - I would also like the ability to test the results both in air and under water? I would also like to determine a baseline for which colors travel furthest in salt water or brackish water conditions. I prefer the test to be completely independent.
Electrical Laboratory needed for battery testing for charges of following test as per IS 1651, Stationary cells and batteries, lead-acid type (with tubular positive plates)
Cell Details : 2V, 100Ah.
1. Test for capacity 2. Test for voltage during discharge. 3. Ampere hour and watt hour efficiency test. 4. Test for loss of capacity on storage. 5. Endurance test, 1500hr cycle testing. 6. Verification of constructional requirement. 7. Verification of marking. 8. Verification of dimensions.
Medical Device Company needs medical technology laboratory for packaging/ product /development of developing a disposable medical cable assembly that will require sterilization. ABS plastic housing for connectors Silicone vs PVC for cable assembly I have questions about cost, materials, packaging and logistics.
ISO 17025 accredited electrical laboratory needed for qualification testing of Medium Voltage Cables rated 5- through 46kV per AEIC CS8, Section 15 for the 120 Day Accelerated Water Treeing Test followed by test protocol to include Electrical Measurements, High Voltage Time Test, Physical Measurements, and Tree Count.
UL, ETL, or NRTL recognized laboratory needed for certification testing of Domestic Storage Water Heaters (3 models) for export in US & Canada market to IEC 60335-2-21 standard. Models have difference is in the water tank capacity and rated wattage of the heating element. The water heaters are supplied at 220Vac, 60Hz supply, single phase, 2kW & 3kW.
Pharmaceutical Laboratory needed for Real Time stability Study Testing. Storage for batches used in the real time stability studies (Chambers with 25deg C)
Electrical Home appliance manufacturer needs Microbiology Laboratory for antimicrobial efficacy testing of UV-light on sterilization. 1. Textiles inoculated bacteria is to be washed in our machine and bacteria reduction is analyzed on textiles. (UV program is to be activated) 2. Empty machine having test material that are inoculated by bacteria adhered to the surface of drum is to be tested and the test material is to be analyzed in terms of bacteria reduction. (UV program is to be activated).
antibacterial tests on washing machine? which bacteria should be tested? which standards do you follow?
ELECTRICAL LABORATORY NEEDED FOR EN AND ANSI BASE PHOTOCELL TESTING (RECEPTACLE) TO ANSI C136.10: 2006 AND NTC 2470, Contact endurance test, Material and capacity of current contacts , Insulation Resistance, Dimensions, sizes and types of conductors connecting the tips, the basis for photocontrol, Base material or recetaculo connection, Dimensional analysis, Maración
Electrical certification laboratory needed for LED Testing for Certificate for CGT FLAT (LED Light Flat tube) Length: 1 meter 1) Lumen Test (4PI) 2) Certification New Epermit + 1 COA IEC60598-1 & IEC60598-2-1 3) Temperature Humidity 85C 85%RH @ 6 hrs 4) Temperature Shock (LN2) -50C to +125C(30min/5min/30min) 1 cyc= 1 hr 15 hrs=15 cycles 5)High Temp Operational Lifetime (HTOL) 120C @ 15 hrs
Performance laboratory needed for endurance testing for a 6 MVA transformer according to EN 50464-4, Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2500 kVA with highest voltage for equipment not exceeding 36 kV . Requirements and tests concerning pressurised corrugated tanks
Laboratory needed for National Electrical Manufacturers Association NEMA testing two LED modules to the 2005 NEMA TS 4, section 5, Display properties? Contrast Ratio Cone of Vision Luminance Intensity Chromaticity Limits. Everything but the Luminous Intensity Uniformity.
The LED modules are 16 pixels x 16 pixels. Each pixel is comprised of 3 LEDs (RGB). The modules are approximately 13x13x1.
FDA Electrical medical device laboratory needed for Skin massager testing: 2. FDA Product Code : PBX 3. Performance test standard ? IEC 60601-1: Medical Electrical Equipment - Part 1: General Requirements For Basic Safety And Essential Performance. ? IEC 60601-1-2: Medical Electrical Equipment - Part 1-2: General Requirements For Basic Safety And Essential Performance - Collateral Standard: Electromagnetic Compatibility ? Requirements And Tests. ? IEC 60601-2-2: Medical Electrical Equipment - Part 2-2: Particular Requirements For The Basic Safety And Essential Performance Of High Frequency Surgical Equipment And High Frequency Surgical Accessories. ? IEC 60601-2-57: Particular Requirements For The Basic Safety And Essential Performance Of Non-Laser Light Source Equipment Intended For Therapeutic, Diagnostic, Monitoring And Cosme
ILAC certified laboratory needed to perform testing of instruments and systems against IEC 60601-1-2, Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests and ISO 14457:2012, Dentistry Handpieces and motors
Large oil company needs electrical laboratory for electrical compliance inspections. At our facility we use hot sticks, release hooks, and other equipment for electrical repair would need certified inspections . Our protective gear and equipment that needs required certified inspections under NEC would be involved also.
Telecommunications laboratory needed for lab examination and reporting of our mobile phone devices that we produce in China. 1) 3G signal quality and speed 2) LTE signal quality and speed 3) WiFi reception quality and speed 4) HD Voice quality 5) Speaker phone, earphone and headset quality 6) Front and Rear camera picture and video quality on different conditions eg low light including flash 7) Screen quality 8) Battery quality and capacity 9) Charging quality
Mechanical Laboratory needed for electrical and mechanical properties testing of 0.40 PVC Shielded cable with 8 22 AWG conductors , we need to get the measures for below: Measure below Mechanical Properties Minimum permitted bend radius Measure below Electrical Properties Conductor resistance @ -10, 20 , 60 deg C Insulation resistance core to core Shield resistance Mutual Capacitance core / core (symmetrical) Mutual Capacitance all core / shield (unsymmetrical) Dielectric strength core/core Inductance (max) core/core Inductance (max) core/shield Inductance (max) all cores/shield
India consumer products laboratory needed for development testing on herbal mosquito repellent voporizer to adjust the evaporation rates. Currently essential oil smell not evaporated from veporizer. There is no equal evaporation from veporizer liquid. Some residue remain.
Electrical laboratory needed for IEC testing of tape (synthetic) used in the fire resistance cables to sustain up to 800 deg celcius of temperature as per IEC-60331. The dimension of tape is 1) 8.00 mm/ 0.11 mm, We need below tests to be performed:- 1) Mica content (g/m2) 2)Glass content (g/m2) 3) Film Content (g/m2) 4) Bond glue content (g/m2) 5) Di electric strength (Kv/Layer) at a) 400 Deg Celcius b) 800 Deg. Celius (Important) 6) Maximum endurance to heat in deg Celsius. The specification standard and test method are as per IEC 60371. Could you please let us know the feasibility and availability of above? Please include a fee quote (kindly make it bifurcated by each test).
ELectrical Product Safety Laboratory needed for European Union EU Restriction of Hazardous Substances Directive ROHS verification of electronic components. quantification of PBB and PBDE, quantification of Cr+6 following abnormal XRF readings performed in-house.
Physical Laboratory needed for thermal and optical properties testing (absorptance/emittance) for a small electronics board (50 mm x 50 mm). The purpose of this test is to fully define the behaviour of the board as it is to be used in space operations.
Materials Laboratory needed for microelectronics testing for collected volatile condensable materials and Total Mass Loss
Electronics Safety Laboratory needed for electrical safety testing of a belt that can communicate and charge batteries and phones of any other wireless devices
Midwest USA electronics laboratory needed for investigation testing to determine the cause of intermittent connectivity or electronic scanning equipment in the field. Several units have been deployed for ~7 years and are starting to register scan failures. The failure is repeatable if the machine is not moved, but when shipped back to the lab it will not reproduce. Scanner recalibration sometimes resolves the issue temporarily, but the units almost always register a future failure. We believe there is an issue with the scanner ZIF connection to the control board. Reseating these connectors resolves the issue for a much longer period of time. We are looking to focus on why that connection appears to be suspect - Whether it be contact force, contamination, corrosion, or other.
Laboratory needed to quote for analysis of appx. 1 oz. of silicone based fluid: chemical composition (quantitative) analysis to a standard and industry available product
Florida electrical safety laboratory needed for shielding effectiveness of EMI Sheidling Equipment
India electronics laboratory needed for EMI / EMC Testing: CE-03 EMI/EMC test as per MIL STD 461C 1 sample; per day basis- multiple iterations of test for specific frequency range
Large electronics manufacturer needs Accelerated Stress Test in high humidity (80%RH), high temperature (70C) for 4 months
Large electronics company needs United States, Japan or Europe Physical Laboratory for ASTM D2628 neoprene testing: Physical Test for Polychloroprene(Neoprene) Elastic Joint Seal Following ASTM D2628 - Tensile Strength - Elongation - Hardness - Oven Aging - Oil Swell - Ozone Resistance - Low Temperature Stiffening - Low/High Temperature Recovery
Asia electrical laboratory needed for required IEC electrical safety testing on Slot machines to fulfill legal regulation? e.g EMC?
San Francisco Bay area Electrical Laboratory needed for full Electricity meter testing to ANSI Standards: ANSI C12.1 is required for Electricity Meters. ANSI C12.1 and ANSI C12.20
Electrical Laboratory needed for IEC Testing: Audio, video and similar electronic apparatus - Safety requirements to IEC 60065 and IEC 60268-3:2013Sound system equipment - Part 3: Amplifiers
New York Metro Area Product Safety Laboratory needed for IEC Testing: Temperature Rise Test for an infrared portable AC Switch to IEC 60884-1: 2002+A1:2006+A2:2013IEC60884-2-5:1995Temperature Rise Test Only 20 samples
Europe electrical product safety laboratory needed for Thermal testing: * Wind Test * IP Test 1-2 units
Interested in outsourcing 3rd party lab for electroacoustic testing services to validate Active Noise Cancelling (ANC) Headphone performance. Sample sizes will vary.
Asia Technology Company needs Africa Electronics Laboratory for Tablet Safety testing including /EMC /RF . Please advice with a CB and CE test report. Could EMC/RF/Safety certificates be obtained ?
Consumer Product Safety Laboratory needed for Skin Allergy Testing on Silicon Rubber Ear Tips for Audio Products. Will expand more when contacted.
Europe electrical laboratory needed for UL508 Overload and Endurance test 100k cycles - General Use - 230VAC 25AAC 0.8 Power factor
Europe Electrical Laboratory needed for ANSI Electrical testing Require ANSI C12.20-2010 Clause:126.96.36.199 & ANSI C12.1-2008 Clause:188.8.131.52: Test No 13: Stability of Performance
Product: Electricity Meter Accuracy Class 0.2
Europe Electronics Laboratory needed for RoHS, IEC 60950 safety test EN/55022 EN/55024 EMC test RoHS Directive 2002/95/EC ?
University Researcher needs Ireland electronics laoratory for cell phone safety and toxcity testing is needed:x-ray fluorescence spectroscopy safety equipment is needed because its flammable and toxic
USA electronics laboratory needed for battery testing of remote controlled helicopters
Electrical Laboratory needed for research study for studying a printed circuit board's (PCB) in-plane CTE and out-of-plane warpage induced by a steady state isothermal temperature TEST ARTICLE: Bare printed circuit board (approximate size of 4"x6") TEST CONDITIONS: STEADY STATE ISOTHERMAL: -40C, 25C, 85C, and 100C DESIRED DATA OUTPUT: 1) In-plane Coefficient of Thermal Expansion (CTE) across the face (4x6" area) at steady state isothermal temperature conditions. 2) Out-of-plane displacement across the face (4x6" area) at 4 steady state isothermal temperature conditions.
USA electrical laboratory needed for electrical Testing of components (transformers, protection equipment, etc) against power grid (15kV) and up voltages.
Electronics Laboratory needed for cell phone testing: Vibration testing for low level low frequency
In order to test sensors of cell phones as follow:
Test load: 300gram.
Level: 10mg, 5mg and 4mg (dwell).
Frequency: 0.5 Hz.
India NABL and ISO Laboratory needed for ASTM and IEC Testing of industrial connectors, we would like to test our products as per IEC 61076-2-101. For further & detailed requirements please email me.
California electrical laboratory needed for IEC Testing: IEC/EN 60747-5-5Optocoupler testing for Approval for Reinforced Insulation
NG and SEC Certified electrical Laboratory needed to test some stranded ground wire. Just dimensions, resistance, resistivity, T&E. The lab needs to be NG / SEC certified.
Large electronics company needs Europe Laboratory for immersion of enclosure product ( 500x230x130)mm in ISOoctane(70) / Toluene (30)
ISO 17025 electrical labooratory needed for IEC Electrical Proficiency Testing for IEC 60076, Power transformers ?. Part 3: Insulation levels, dielectric tests and external clearances in air.
ILAC Accredited Laboratory in Europe needed for electrical testing: Accuracy testing for a voltmeter with HV probe(1/1000) in the range of 1kV to 4kV Accuracy -max.3%
USA electrical laboratory needed for ANSI certification testing to test/certify our electrical connector devices as per ANSI C119 (direct burial application)
Materials Laboratory needed for Fluid analysis for High Voltage Power supply Transformer fluid? Amounts follow: 1 00.55 ounces 2 11.60 ounces 3 08.85 ounces 4 05.75 ounces 5 07.65 ounces 6 11.00 ounces Please provide quote for analysis
Electrical laboratory needed for re-designing existing power supply modules (dual power supply,. Triple power supply ,SSR) of air-born systems. We need to perform the DO160 and MIL-STD-883 test as attached
Optical Laboratory needed for Optical Testing: European Standards Testing to DIN 5032 Part 7 Photometry; classification of illuminance meters and luminance meters
Mexico or USA Electrical Certification Laboratory needed for Photovoltaic certification of photovoltaic panels to IEC 61853 or ASTM E1036-02 some of my products under these standards.
Photovoltaic panels -IEC 61853 or ASTM E1036-02 or FESEC 202-05 or some similar
Inverters -EN 50530 or any other similar.
-UL 1741 or CSA 22.2 No. 107.1-M91
Electrical equipment importer needs electrical certification lab for certification verification testing to verify the authenticity of a CB Test Certificate & Report for LED TV provided by supplier and issued by the following NEMKO Laboratory in Hong Kong, and if this lab is accredited so that its certification will be accepted by (JSMO), the Jordanian Standards & Metrology Organisation for import approvals: NEMKO
Electronic manufacturer needs electronic laboratory for reliabiity testing and failure analysis testing.
Electronics Laboratory needed for Voltage Testing: Low-Voltage Ride-Through (LVRT) or Fault-Ride-Through (FRT), according to ANRE order 74 - Romania. The test consist of a voltage drop from 85%Un to 15% Un and will check the response on the inverters (response time, restart curve), as to the attached graph. Inverter producer: WOODWARD IDS Inverter model: Solo 500 Please inform us of the availability to perform this tests, costs, duration and reports issuing time. Also there are 4 more companies that are interested in performing this test.
Materials laboratory needed for ASTM Testing. Electrical insulating fluid testing for CTE Test. isoparaffinic oil and a standard white oil. I can provide samples of each as required for testing. I'm not sure what all you offer so please quote any of the following that you may be able to offer:
1. Thermal Coefficient Expansion of each fluid across a range of operating temperatures typically found in computing environments (servers, desktops, etc.). Please quote separately (cost for each fluid testing), time to complete, amount of fluid sample required, and report you will provide upon completion. 2. I'm also seeking to measure the Effect of Thermal Conductivity and/or Latent Heat of Vaporization of Liquid on Heat Transfer in Liquid immersion applications - I would provide fluids for testing and could also provide a Raspberry Pi or sim
ISO 17025 laboratory needed for inter-laboratory comparison testing of circuit boards. Please confirm that 1. Is your lab ISO 17025 accredited for the test method below? Ionic Contamination Test for Circuit Board Test items: a variety of ions contamination test (F-, Cl-, Br-, I-, SO42-) Test Standard?IPC-TM-650 2.3.28 2. If yes, please send us the quotation and leadtime for one sample.
Canada analytical chemistry laboratory needed for chemical Testing of the contents to ensure that there are no chemicals and is 100% natural. Two samples.
European Union Electrical Laboratory needed for RoHS testing and REACH Compliance testing: Could you perform analysis for substance detection as (reference: current list of SVHC published by the ECHA) on smart-cards (SIM)? RoHS: Could you do also analysis of the same article for confirming the RoHS compliance? If yes, what's the lead-time and fare?
ASIA electronics laboratory needed for IEC Testing: Lab Heat cycle testing of electrical Fittings to IEC 61238-1
Electronics Laboratory needed for SAE Testing to SAE J575, SAE J579, SAE J1330, vibration test, moisture test, dust test, corrotion test, warpage test for plastic components, photometry, flash rate, color test,high temperature flash rate test, low temperature flash rate test, durability flash rate test.
US Electrical Laboratory needed for ANSI Electric Meter Testing To test 1 to 3 samples, reference ANSI C12.1 Section 184.108.40.206.1 and 220.127.116.11.3 and customer test plan used. Product : BLP Disconnect II Description : 200A, 2-phase contactor for utility metering
Asia Electrical Lab needed for IEC TESTING: Electrical Laboratory testing Services for the 150 kV transmission insulators, such as the visual test, Dry / wet power frequency withstand voltage test, failed test and inform us about the number of samples to be tested as well as the entire cost of testing with the fee details
Electrical Laboratory needed for Optical testing based on EN12966 Testing lumunance and contrast of emitted light (using LED's) within certain beam widths to determine gaps as compared to EN12966 specifications. EN12966 is an European Traffic display standard.
Electronics Manufacturer needs metallurgical laboratory for stainless stell teting for Metallurgical confirmation or not, & Corrosion Puported paramagnetic 304 stainless steel chain that is instead magnetic and corroding ...
Need a quote for test to establish what it is ...
Need a quote for test to characterize corrosion ...
Asia electrical laboratory needed for IEEE Testing: Electrical Heat cycle Test & IEC61238-1(2003-5) & Ageing Test & Tensile stress test
Asia electrical laboratory needed for CE Marking, IEEE Testing to Electrical IEC61238 Product = Voltage detector TestPen CAT IV 1000V.
NABL Texas electrical laboratory needed for ASTM Testingof aluminum alloy composition to ASTM B233. Must be NABL accredited
India Government approved Laboratory needed for electrical testing of Electrical Insulated Mat material (CONFIRMING to IS 15652:2006).
Middle East Electrical laboratory needed for IEC Testing of different types of Lamps Luminaries in accordance with IEC standards
India NABL Laboratory needed for Dye penetration testing as per IS-3658 -1999 CL7, Code of practice for liquid penetrant flaw detection
Electrical Laboratory needed for IEEE electrical Testing: electric arc erosion rate in low voltage circuit breakers arc erosion rate for low voltage and current ranging from 100-1000A
Electrical laboratory needed for bending endurance testing on test cable under varying temperature conditions. Following this a voltage test on the insulation needs to be conducted.( A full description of the test and cable will be provided to Labs who can do this kind of testing.)
URGENT: Stainless steel electrical junction boxes manufacturer needs ISO/EC 17025 physical laboratory for IK10 Impact testing to ASNZS 60079 or IEC 60079 and the lab must be ISO/EC 17025 certified.
Chicago Electrical Laboratory needed for certification testing: Mated Electrical Connector IP69K Testing. There will be two sets of mated assemblies, 6-10 samples each. Each mated pair will consist of a male and female overmolded connector assembly with cable or wires attached.
NABL / AALAC electrical laboratory needed for complete electronic testing of electronic fan regulator (capacitor type) as per IS:11037
Electronic laboratory needed for BIO Certification testing of Multi Media Projectors. As per Indian Government guidelines, we need to get the product BIS certified.
Pacific Northwest USA physical laboratory needed for physical testing: Vibration testing, Mechanical Shock testing, Humidity testing, and Temperature Shock testing
British Columbia, Canada electrical laboratory needed for ANSI Testing to ANSI 12.1 Revenue grade meters/CT energy metering module that can meter single/polyphase 120V Rated. All configs require a neutral. The meter has 100mA inputs. Works with 100-0.1A;200-0.1A;400-0.1A CT's.The module has a local display unit
Electronics laboratory and analytical chemistry laboratory needed for mercury lighting fitting testing. Test for LED, sodium vapor, metalhalide, cfl, and mercury light fittings "
Analytical Chemistry Laboratory needed for analytical chemistry Testing mass diffusion coefficient of metal ions in a liquid solution. 5 Samples at 4 different temperatures.
Testing the same samples for specific heat capacity and thermal conductivity. Samples may not be exposed to nickel alloys such as stainless steel.
Large electronics firm needs Textile laboratory for AATCC Testing: AATCC 15 Colorfastness testing
India electrical laboratory needed for IEEE Testing of HDPE pin Insulators to ANSI standards
Electronics manufacturer needs electrical laboratory for ISO Testing: ISO contamination Testing according ISO 16232 Road vehicles Cleanliness of components of fluid circuits
Asia electrical laboratory needed for IEC Testing High voltage detector as per IEC 61243-1, Live working - Voltage detectors , ."
New Jersey Electrical Laboratory needed for antenna testing for Measurement of antenna characteristics
Large electronics manufacturer needs physical laboratory for radar testing. Radar that I need to remain stationary while two objects move at varying angles, velocities, and directions with respect to the stationary object. I need the motion and position to be accurate to within 1cm, I need velocities of up to 7 m/s, and I need am maximum distance of 25m.
India electrical laboratory needed for IEC Testing of Solar Inverter to IEC 60068-2 214.30
NY electrical laboratory needed for electronics testing of recycled electronic products. 100% of the metals and nonmetals with our patented technology
Large electronics manufacturer needs Electrical Laboratory needed for voltage testing to Track and time to Track testing? We normally do samples in groups of three, so give a price quote based on three test samples.
Large Electronics Manufacturer needs qualified electrical laboratory to Perform DMA or DSC on resin sample to obtain Tg per requireemnt(provided)."
Florida physical laboratory needed for transportation vibration tests on radio assembly as per Mil Std 810 Method 514.6 General Vibration procedures 1 and 2."
Electrical laboratory needed for prototyping: prototype materials for OLEDs synthesized."
Africa electrical laboratory needed for maximum power transfer testing: wattmeters, voltmeter, ameter, power supply, resistance,cables
India Electrical Laboratory needed for International Electrotechnical Commission (IEC testing electronics testing to IEC 60228, conductors of insulated cables
Certification Laboratory needed for ANSI certification compliance testing certify compliance with ANSI C12.18 American National Standard Protocol Specification for ANSI Type 2 Optical Port ANSI C12.19 SmartGrid/AEIC AMI Interoperability Standard Guidelinestogether with a smart meter.
Asia lightning certification laboratory needed for certification testing for early streamer emission(lightning protection system)
INDIA ELECTRICAL LABORATORY NEEDED FOR ELECTRICAL TESTING OF IP CAMERA TESTING INCLUDING FOCAL LENGTH, ACTIVE PIXELS , IR CORRECTION ETC.
Thailand electrical laboratory needed for IEC testing, CABLE TRAY SYSTEMS. AND CABLE LADDER SYSTEMS
Asia Acoustics Laboratory needed for acoustics testing: Peak Sound Pressure Level Compliance, Acoustic Shock and Maximum Sound Pressure Level compliance
USA electical laboratory needed for IEEE Testin to IEEE 1202 Cable Tray Flame Testing
US electronics laboratory needed for IEEE Testing: IEEE Electrical Surge testing: IEEE C62.41.2 Location Category A
Electrical laboratory needed for IEC Testing: Inclined Plane, Tracking and Erosian tests to International Standard IEC 287, Electric cables - Calculation of the current rating
Electronics Laboratory needed for ANSI Testing. 5 samples tested to: ANSI C12.1-2008 part 18.104.22.168.1. Electric Meters Code for Electricity Metering and 5 samples tested to 22.214.171.124.3.
Note that these are contactors only.
Plastics Laboratory needed for ASTM Plastic Testing of injection plastic components of PBT Valox, particulary. Fusion point, Fuid point, specific weight, hatdness, tensile strenght.
USA Electrical Certification Laboratory needed for IEC Testing: X-Ray Film Digitizer Equipment IEC 60601-1 3rd Edition and a test report and CB certificate for Brazil.
India Electrical Laboratory needed for RFI and EMI LED Tube Light testing and certification of Led Tube light I.e.T8 led tube light. 2 numbers. 1) Minimum Starting voltage2)Input Power3)Input power factor4)Input Current Harmonics5)Input Current Crest factor6)Inrush Current protection7)Compliance to RFI & EMI norms Kindly send us the Quotation firstly.
India Electrical Laboratory needed for electrical Testing of Electrical measuring instrument
Europe Electrical Laboratory needed for IEC Voltage Testing to IEC 60243 for dielectric properties of the insulating coating applied on a substrate of Ti alloy.Standard test that we want to use is BS EN 60243 or IEC 60243
India electrical laboratory needed for IEC electrical testing: high current and high voltage
China CNAS accreditated test laboratory needed for IEC Testing. Mechanical failing Load Testing on 36KV Pin Porcelain Insulator for 10KN
Electrical Laboratory needed for IEC electrical testing as per IEC 60076: C2 E2 F1 TESTING OF DRY TYPE CAST RESIN TRANSFORMER AS PER IEC 60076
Large manufacturer needs California Physical Laboratory for ASTM Testing ASTM D 1044/1003. Abrasion Testing to Our company will be starting a new project and we are looking for a lab to send continuous samples to for weatherability testing and abrasion testing as well. Please respond and will have more info.
Large electronics firm needs electrical laboratory for electrical product safety testing 1.Need you support to Know Which are the Labs do have facility for LCD /LED product safety testing as per IS616: 2010. 2. Time period for testing & issuing certificate 3. Testing charges??.
India electrical laboratory needed for electrical product safety testing 1. LCD /LED product safety testing as per IS616: 2010. 2. Time period for testing & issuing certificate 3. Testing charges...
South Korea Materials Laboratory needed for ASTM Testing and ISO Testing, Corrosion analysis testing is needed to verify resistance of external facing ATM (automated teller machine) components
ELECTRICAL LABORATORY NEEDED FOR ASTM TESTING, DIELECTRIC CONSTANT AND DISSIPATION FACTOR FROM 2 UP TO 14 GIGA HERTZ TO ASTM D 150, Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation ASTM D 5568 Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials
Turkey electrical laboratory needed for IEC Testing : type tests according to iec 60071-202 for prefabricated compact substation
USA Electrical and Mechanical Laboratory needed for ANSI Testing: Pefrom the Complete set of testing describe in ANSI 119.4 for Al-AL conductors with a wire range
INDIA PHYSICAL LABORATORY NEEDED FOR ANSI AND UL TESTING TO ANSI/ UL 1709 RAPID RAISE FIRE TEST FIRE PROOF ENCLOSURE FOR HYDRAULIC,ELECTRIC,PNEUMATIC ACTUATOR, TEMP-1400 C DEGREE, 2"F0R 3O MINIUTS AND 4"FRO 1 HOURES.
India Electrical Laboratory needed for EMI & EMC TESTING 1 Rectilinear Potentiometer Penny & Giles SLS-095-075-3K-P-66 1 2 Single Turn Potentiometer Coudoint PR18 1 3 Load Cell Honey Well 141 (AL414DR,1A,2U,6A,13B,15A) 1 4 Multi Turn Potentiometer Sensor System Model MD-09 1
USA Electrical Laboratory needed for UL Testing: 1 sample for UL 181 Erosion resistance. request from client (item 2 only): 1. We have an electrical connector (one metal sample) in which the components (rubber, metal, plastic) must be "mercury free". No metal is expected.
2. Please quote UL 181 Erosion Resistance testing for one material.
UK physical laboratory needed for optical testing.. Compare light transmittance between two touch sensor variants.
Construction 1: 4mm plain glass 125µm PSA PET hard coat film AR film
Construction 2: 4mm AG glass 125µm PSA PET hard coat film
UK Electrical Laboratory needed for UL Short Circuit Testing 100,000 amp short circuit UL Follow-Up test program
Malaysia, Penang or Singapore electrical laboratory needed to conduct current saturation test and Irms test for an inductor"
Metrology Laboratory needed for Calibration of air nozzle to about 45 kg/s. Nozzle throat is ~760 mm
USA, East Coast, California, Chicago, Phoenix, or Houston Electrical and environmental Laboratory needed for ANSI testing of smart meters per ANSI C12.1-2008, Standard: American National Standard for Electric Meters Code for Electricity Metering ANSI Tests number 15, 17, 20, 37, and 38
Aia Electrical Laboratory needed for electrical and Physical testing of Cat5e FTP cable: Item testing, Rating testing, Conductor Resistance Testing, Mutual Capacitance Testing, Dielectric Strength Testing, Spark Testing, Flame Retardant Testing, Characteristic Impedence Testing, Structural Return Loss Testing, Propagation Delay Testing, & Data rate Testing.
USA ELECTRICAL PRODUCT SAFETY LABORATORY NEEDED FOR IEC TESTING: WIRE TESTING FOR HALOGEN CONTENT TO IEC 60754-1, test on gases evolved during combustion of materials from cables
Electrical Laboratory needed for IEC Testing to IEC 60754-1, Test on gases evolved during combustion of materials from cables - Part 1: Determination of the halogen acid gas content & IEC 60754-2, Test on gases evolved during combustion of materials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity
Electrical Laboratory needed for International Electrotechnical Commission IEC Testing to IEC61643-321 Components for low-voltage surge protective devices - Part 321: Specifications for avalanche breakdown diode (ABD)? What is the cost? What is the turn time?
Europe Electrical Laboratory needed for IEC Testing: short circuit test cable clamp K36/52 according to IEC 61914, Cable cleats for electrical installations
Lighting company needs electrical laboratory for IEEE electrical testing to IEEE 1313.1 standard, Standard for Insulation Coordination - Definitions, Principles, and Rules
Electrical Laboratory needed for International Electrotechnical Commission IEC Testing of electrical adhesive tape to IEC Specification, IEC 60454-3-1, Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials.
USA or Canada Electronics Laboratory needed for IPX-6 Testing to IEC Std. 60529 Section 14.2.6Moisture Intrusion testing on electric toothbrush size appliances.
West Coast UL Electronic Certification Laboratory needed for UL Certificaiton testing to Certify an inverter to U.L. 1741,Inverters, Converters, Controllers and Interconnection System Equipment for Use With Distributed Energy Resources
NEED QUOTE ASAP
Europe Electrical Laboratory needed for IEC Testing, Mechanical and Electrical Testing of cable cleats for IEC 61914, Cable cleats for electrical installations both mechanical and electricaly. Can be olso done seperately.
Electrical Laboratory needed for IEC Testing: IEC 61230, Portable equipment for earthing or earthing and short-circuiting
India Electrical Laboratory needed for Electrical Resistance Testing in accordance with MIL-DTL-5541 Cl-3, Military Specification, Chemical Conversion Coatings on Aluminum and Aluminum Alloys
Mexico certification laboratory needed for electrical reliability Testing for equipment:
Brand: Monster Power Model: HDP 1800 Description: High definition power center with clean power stage 2 filtering.
Large Electronics Manufacturer needs Radiochemistry Laboratory for Radiation Detection test of our Japan goods before ship them to Iraq to comply Iraq Government regulation.
Electrical Laboratory needed for Electrical Testing of Electrical Insulator Sheet,which is used like a carpet in front of Substation, High Voltage Generators & Hidg Voltage Duty Rooms
Large Electronics company needed India materials laboratory for Photobiological safety testing of LED LIght Test Ultraviolet hazardUV Hazardaretinal thermal hazardinfrared radiation
Electrical Laboratory needed for Electrical Testing, Transformer Testing to IEC Standard IEC60044-1 Instrument transformers
Large Electronics Mfg needs West Coast USA electrical laboratory for qualification testing of electrical brushless motor connector contacts to separate peak and RMS current requirements.
ELECTRONICS CERTIFICATION LABORATORY NEEDED: CE LABORATORY FOR ELECTRICAL CERTIFICATION OF OUR POWER SUPPLY(SAFETY & EMI/EMC) WE ARE MANUFACTURER OF EDUCATION AND AGRICULTURE LAB EQUIPMENTS
Brazilian Trading Company needs electrical laboratory for quality control testing to have quality control inspection on the production in China and quality control to check if the devices attend what the supplier agreed to offer. Do you provide this type of quality control? To start with it might be about 1000 tablets
USA electrical labroatory needed for polymer/ceramic testing: Dielectric constant and dielectric strength of polymer/ceramic nanocomposite
Europe Physical Laboratory needed for Dust Chamber Testing to check the entry and departure system of a door in a train for this reason the dust chamber that we need it is big (2x2x2 aprox.)
I´m waiting for hear from you soon
Best regards. "
Mechanical laboratory needed for abrasion testing by using ABREX equipment. Test item : IEC60068-2-70 Test component : Knob of Automotive interior parts ( Steering wheel switch ) please send quotation.
British Columbia Packaging Laboratory needed for ASTM Testing to ASTM 4169 09 Standard Practice for Performance Testing of Shipping Containers and Systemtesting for paletized packaging using intermodal and over the road transportation.
Electrical Laboratory urgently needed for IEC Testing to IEC 550C and IEC 750C Glow wire testing done plus 175PTI testing done by lab that is approved to do IEC testing. These tests are found in IEC 60335-1 standard.
Electrical Laboratory needed for NFC and IEC Testing of aerial cables to NFC-33-209 & IEC 60228: TYPE TESTING & UV TESTING OF AERIAL BUNCHED CABLES 1 X70 + 3 X 120 sq mm AS PER NFC-33-209
Large Electronics Manufacturer needs USA Electrical Laboratory needed for IEC Testing to IEC 60335-1 Clause 30 glow wire testing which references IEC 60695-2-11 on several material samples.
Electronics laboratory needed for dielectric spectroscopy experiments in testing aqueous solutions.
Sri Lanka or India Microbiology Laboratory needed for ASTM Testing biodegradability testing of plastic materials relative to ASTM D5988 a standard in an aerobic environment. This test method is designed to be applicable to all plastic materials that are not inhibitory to the bacteria and fungi present in soil and compost
South Korea ISO Analytical Chemistry Laboratory needed for WVTR and OTR Testing for AL2O3 Coated flexible substrates done by atomic layer deposition for electronic devices.
Electrical Laboratory needed for ANSI Testing to ANSI C 136.10 locking-type photocontrol, used to control street luminaires, to standard ANSI C 136.10. Certification is not required, just a test report.
Mumbai electrical laboratory needed for LED Testig to test light output intensity of LEDs
Large Corporation needs India Mechanical Laboratory for Site testing: Mechanical endurance test on High voltage circuit breaker as per IEC 62271-100
Electronics Laboratory needed for fuse testing. The fuse is rated at 15 amps 250 VAC. We can supply the currently approved vendors parts and the new suggest source. We need to verify these fuses trip at the same points along the various time to trip graphs."
Electrical physical laboratory needed for insulation testing - water absorption- on insulation of LT Aerial Bunch Cables please and whether tube extruded insulation will meet these tests
Electrical Laboratory needed for ASTM Testing: ASTM D-877 electrical breakdown astm D-924 Power Factor 25C&100C ASTM D-92 Flashpoint ASTM D-971 Interfacial Tension ASTM D-5837 Furanic Compounds AN-1000 filtering charact/carbonyls
Physical Laboratory needed for vibration testing to MIL-STD, Mil-STD-202G, Method 214AThe specimens are flexible electronic PWBS and the largest one measures 54" long, 6" wide, 1" deep.
Electrical Laboratory needed for IEEE Testing: Electrical temp-rise testing. Perform temp-rise test on a bushing rated at 21,500 amps per IEEE standards. This unit also requires 30% overload and zero current.
India Mechanical Laboratory needed for DIN Testing Test Details: Specification - Equivalent to DIN 50018 The test duration of Saturated SO2 test is 3-Cycles (72-hours) One Cycle : 8 hours in SO2 atmosphere (0.67% Concentration) and 16 hours in regular air. Sample Details: Automotive alternator motor Dimention: Length- 200mm / Hight - 220mm / Width - 220mm
Texas Electrical Laboratory needed for UL Testing: ul61010-1 Standard: Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use
India Global Certified Laboratory needed for Electronics product Testing - Automotive"
USA A2LA electrical labroatory needed for ASTM Testing to ASTM D924-08, Determination of dielectric constant of thick (~20 mil), flexible films
India Electrical Laboratory needed for Acceptance Testing to IS Specification ForLT(1.1 KV) ,2.5 sqmm 2 Core PVC Insulated Aluminium Electric Service Connection Cable 4to 5 Samples from each Coil
Electrical laboratory needed for IEC Testing to IEC 61643-11 for our product LV Surge Arrester rate 480V. We will be much more appreciated if you can do advise institute to us for contacting.
Electrical Laboratory needed for Electrical Acceptance Testing for 1.1KV 2.5sqmm,2ccore,PVC insulated,Aluminium Electrical service Connection Cable (of Sample to be submitted)
Germany electronics manufacturer needed electrical laboratory for CE Testing of DC power supply testing with input of 90-240VAC and 48V, 30A DC."
Electrical Certification Laboratory needed for electrical certification testing (1) Conduct IEC 60695-11-10 Flammability test at 3.0mm thick for HB40 rating. (2) Conduct IEC 60695-2-12 550°C Glow Wire Test (GWFI) on plaques of material (3) Conduct IEC 60695-2-11 550°C Glow Wire Test on all end product components (4) Conduct IEC60730-2-9, IEC60730-1, including EN60730-2-9 differences. Please forward lab location, lab cert with scope showing above standards listed.
USA Medical Electronics Laboratory needed for ECG Electrode Testing to AAMI standards: AAMI ECG Electrode testing EC12
Large electronics mfg needed electrical laboratory for IEC electrical testing: Dielectric and short-circuit current tests for disconnector switchs of 145KV/40KA
Plastics and Polymers Laboratory needed for ASTM Testing to measure melt flow rate for epoxy according to ASTM 1238-10 or ISO1133.
India Electrical Certification Laboratory needed for Certification Testing of: Monitor LG 22" Monitor M227WA 1. Horizontal Resolution (500 TV Lines) 2. Luminance Level (500 Cd/Sq.mm) 3. Viewing Angle +or - 80 Degrees (vertical) & +or- 80 degrees (Horizontal) "
California Electrical Laboratory needed for ASTM Testing ASTM B539 - Electrical Test - one sample of customer part - coated with chemical film (alodine), aluminum material, 6061 alloy.
Large multi-national company needs Asia electrical certificaiton laboratory for EMI/EMC Certification testing as per DO-160F/G
UAE, ASIA ENERGY LABORATORY NEEDED FOR IEC TESTING LUMINARY TEST : IEC60598 with several parts
EASTERN USA ELECTRONICS LABORATORY NEEDED FOR ELECTRICAL SAFETY TESTING for LVD using IEC 61010-1: >> Ground bond test >> Insulation resistance test >> Dielectric strength test >> Line leakage test
US Optical Laboratory needed for ASTM Optical Testing: (Transmission, Reflectance,Haze) 5 samples
Eastern USA Mechanical Laboratory needed for Mechanical Testing on a Clamp Mil Spec testing on a clamp assembly. 4.5.1 Hydrostatic Pressure4.5.2 Static Operating and Proof Pressure Leakage Test.4.5.3 Tensional Moment4.5.4 Vibration Performance126.96.36.199 Vibration-Structural Integrity188.8.131.52 Resonance Search4.5.5 Pressure Cycle4.5.6 Flexure Cycling4.5.8 Coupling Half Strength Test4.5.9 Safety Latch Evaluation4.5.10 Nut Life4.5.11 Disassembly and Inspection4.5.12 Burst Pressure
Electrical Laboratory needed for electrical testing to: PM8374A-NI 712 PCS PM8354A-NI 200 PCS
Eastern USA metallurgical laboratory needed for analyzing a rust condition on fuse holders (on a PC Board) as to the following:
1)Root cause of the rust 2)An impartial summary as to who, what may have caused the condition 3)Any suggestions as to if the parts can be cleaned & used, or if the fuse holders must be removed and replaced 4)Any other pertinent data that your metallurgist deems useful in proving the cause and any potential solution to this problem.
Non-destructive Laboratory needed for non-destructive testing: X-ray inspection of zinc die cast parts to detect internal cracks or flaws: parts quantity =10 dims are .125"x.25"x.250" approx.
UK electrical laboratory needed for electronics mcb,rcbo and etc.. we import them from china
Electrical laboratory needed for IEC Testing, Type tests per IEC 61439-1 of 380 V Switchgear will be tested for type tests and certified
Large computer company needs Massachusetts Metallurgical Laboratory for metal content analysis to analyze platinum content from a sample of finely crushed electronics.
India Electrical Laboratory needed for IEX Testing of Press Boards (made as per IEC 60641-3-1), for use in Electrical Transformers of 400KV and above. Kindly inform the sample size, nos of samples, fee etc.Also, kindly inform the highest KV Transformers for which, you can conduct the tests on Press Boards.A prompt reply is required please.
Electrical laboratory needed for EMC Testing, ENEC for LED convertor. Can we know price and actual sample needed.
India physical laboratory needed for NFPA Certification Testing to NFPA 496 certification test for our Z purgeing system
West Coast Analytical Chemistry Laboratory needed for ICP-MS testing or possibly AA testing of Semicnoductor proccesing acid bath containing the following nominal concentrations: HNO3: 39.3% HF: 11.3% Si: 0.94% (4.85% as H2SiF6) I believe this is done by ICP-MS or possibly AA. We would likely need to submit a relatively small number of samples (between 10 and 20 likely) for assay.
Large office equipment manufacturer needs electronics laboratory for Conductivity measurements of powders measure the conductivity of 3 laser beam printers toners (D50 = 8 - 10 micron)
Large electronics manufacturer needs Canada or USA Electrical Laboratory for electrical (12,000 amp, 4 cycls, 240Volt source) testing. Fixturing would be brought by us (GE). Many future tests will be contracted.
Large multinational electronics manufacturer needs electrical laboratory for NEMA 3R water type testing, preferably in or near Greater Toronto Area, so that we will have comfort to ship and handle.
Structure is an MCC - Motor Control Centre (MCC) - two vertical section of each size 20" W x 90" H x 15"D. Hence total dimensions for MCC is 40" W x 90" H x 15"D. A picture attached for review.
Request to please quote along with testing time.
EUROPE Physical, Electrical laboratory needed for ASTM Testing: Elastic pelma:
1. Resistance towards friction. ASTM-D-1630-83
2. Resistance towards bends ASTM-D-1052-55 (1985)
Upper leather of the boot:
- Waterproofness of the boot's upper leather according to ISO 5403:2003 (IUP 10)
Southern California Electronics, Automotive Laboratory needed for testing electronic device that claims to increase MPG and reduce emissions.
India Electrical Certification Laboratory needed for IEC Certification Testing to IEC 61215 - 2ND EDITION (2005) & IEC 61730 -1 :2007
Type of Certifications: IEC 61215 - 2ND EDITION (2005) & IEC 61730 -1 :2007& IEC 61730 - 2: 2007
Product Specification: Their products are 06 nos. Solar panel (20W, 40W, 80W, 100W, 120W and 200W
Recognized certificate: Please give some notes about recognition of certificates. Requirment: Financial proposal for both laboratory test and certification indetails including transportaion .
USA electrical laboratory needed for electromechanical QPL qualification testing Short Circuit Test per MIL-PRF-22885 Section 3.29 , subsection 184.108.40.206 method I
Ergonomics Chair Mfg needs electronics certification laboratory for electrical certifications: PSE certification for the Japanese market but we're confused between the CB and the PSE. Should we go for the CB and do the exceptions to get the PSE after or should we test directly to obtain the PSE ?
Large, multinational company needs Canada analytical chemistry laboratory for water testing. For the jar testing our goal was manganese oxidation. We previously did jar testing at a local lab using aeration only. This successfully oxidized the iron (which would then be filtered by the downstream UF membranes), but did not significantly oxidize the Manganese.
Hence, we decided on a second round of jar testing, for this Project. These jar tests would investigate the use of oxidant, specifically chlorine, either instead of or in addition to aeration.
Essentially the goal is to oxidize enough Mn to have < 0.04 mg/L soluble Mn. The UF membrane (0.1 micron absolute pore size) would remove the oxidized Mn, so that total Mn in the UF permeate would be < 0.04 mg/L.
So, we need to do jar tests to try and get < 0.04 mg/L soluble Mn using:
Ontario ISO Electrical Laboratory needed to measure Electrical Characterisics for a 50 OHM Iff Feed System -Antenna Arrays
Electrical Laboratory needed for EN 50178 Testing of Partial static discharge, high voltage isolation, and dV/dt testing to EN 50178 specifications. The product is a dual channel IGBT driver for use with IGBT switches.
Electrical Laboratory needed for EMR testing or proprietary material we have designed to electrical field blocking medium block EMR. Similar to a faraday cage, our material has a conductive carbon grid woven in a polyester based fabric. We want third party testing to show us what percentage of EMR we are blocking.
Bihar electrical labroatory needed for calbration testing of Meggar Meter- Waco Make
Electrical laboratory needed for DC characterization services on test pin that use as a medium to transfer signal between IC chip and test board use in SEMICONDUCTOR factory? Contact DC Resistance (mΩ) Current Carrying Capacity (A) Current Leakage (pA@V)
Electrical Laboratory needed for TCP/IP Stack Compliance Testing for the following IPv4 protocols: DHCP, Telnet, UDP, TCP & ARP.
Electrical Laboratory needed for ANSI Testing Dielectric testing, Humidity testing and Electrical testing for a 765kV insulated aerial lift. (Withstand test up to 1105kV, switch surge up to 1560kV)
Europe Electrical Laboratory needed for Electrical Connector Testing of connectors and wiring related to electronic boards in home appliance and automotive environment
West Coast Electrical Laboratory needed for EIA Evaluation: Evaluate edge card connector contacts and mating edge card fingers for gold porosity to base metal. 2 samples each of 2 mated pairs (8 samples total, evaluate 10 contacts per sample)
Electrical laboratory needed for voltage testing of Lead Acid Battery 12volt& 2volts
Asia Electrical Laboratory needed for IEC Testing: Motor Circuit breakers IEC 60947, IEC 60947-1 2) Contactors IEC 60947-4, IEC 60947-5 3) Relays IEC 61810 4) Pressure Switch, Selector Switch IEC 60947-5
India Electrical Laboratory needed for IEC 60439 Busway Temp. Rise Test for Plug in Box.
USA West Coast Electronics Laboratory needed for circuit board testing and burn-in at temperature extremes -20C to +50C. (10 samples)
US Laboratory needed for measurement of total hemispherical emittance of a thin film substrate. (non destructive)
Electrical Certification Laboratory needed for EMC Testing RF short rage imtrusion detector to INDIA standards
USA Electronics Laboratory needed for static breakdown voltage, insulation resistance between terminals, visual & mechanical, parametric defects, and combined catastrophic and parametric defect.
JAPAN ELECTRICAL LABORATORY NEEDED FOR PRETESTING OF SOLAR PANELS MFG IN JAPAN. ULTIMATE END USER LOCATED IN ITALY.
ASTM Electrical Laboratory needed for testing to determine volume resistivity on a sample of epoxidized soybean oil as per ASTM D-1169.
India IEC Electrical Laboratory needed for IEC testing conformal coated board by UV40 chemical as per IEC 60664-3 standard
Vancouver, Canada VCCI Electrical Laboratory needed for EMC testing as per Japanese EMC requirements.
Electrical Laboratory needed for type tests of insulation piercing connectors according to NFC 33 020.
India Electrical Laboratory needed for testing of IEC socket products as per UL & IEC standards
Electrical Laboratory needed for electronic reliability characterization testing - Electron Beam Moire or other methods to chronicle fine movement of select features of high density interconnect system, for example solder mask movement with respect to solder bump.
Acoustics Laboratory needed for product vibration testing for 2 hours at 17 Hz with an amplitude 1.5 mm in each 3 axes. Product is a small (80mmx60mmx30mm) box with electronic controller inside. Please quote testing of 1 sample.
USA/Taiwan SAE Mechanical Laboratory needed for SAE J 2202, J1113, and J1455 testing and certification - We will send in wire and product samples.
Albania Electrical Laboratory needed for Medium Voltage Cable Connector and Terminals Test to obtain Sign and Sealed sheets.
UL Electrical Laboratory needed to test espresso machine (small appliance for home and office use) to certify electrical safety for UL listing of product.
USA Electrical Laboratory needed for product safety testing to see if product conducts electricity. Looking for a KVA rating on this device.
Europe IEEE Electrical Laboratory needed for testing Surge Suppressors as per IEEE Standards.
Mechanical Laboratory needed for Mechanical properties testing - Mechanical resistance, young/Elastic modules,Tensile strength, Compressive strength and Poisson ratio of solar pattern glass.
Electrical Laboratory needed for electrical quality control testing in accordance to ISC, CE, ISI, SNI, ICC, PSB, BSMI, TIS,ETL
Electrical Laboratory needed for electrical environment testing of an industrial control device tested to demonstrate robust operation in a noisy electrical environment. Electrical noise would be generated by large AC motors turning on and off.
Europe certification laboratory needed for EN conformity testing to EN 50483 of aerial bundled cable accessories for conformity to requirements of standards series EN 50483.
USA Electrical Laboratory needed for testing to review and do a comparison of 2 different circuit boards that are used in 2 of our similar electric products.
Midwest USA Electrical laboratory needed for DIN Testing: Water spray testing electrical switches to IP69K Per DIN 40050-9
Arizona Electrical Laboratory needed for particle size distribution testing by laser light scattering method.
EPA Toxicology Laboratory needed for testing a suspension of a nanoscale metal coating solution for reporting on an MSDS for acute and chronic exposure
Toronto IPC Instrumentation Laboratory needed for Ion Chromatography & Scanning Electron Microscope measurement in accordance to IPC-TM-650
Eastern USA Electrical Laboratory needed to test 60W drivers for use with LED lights
Electrical Laboratory needed for IEEE testing High Voltage Surge Arresters to IEEE Std. 62.11
Southeastern USA ISO Electrical Laboratory needed for Dimensional Testing of small electronics parts in accordance to ISO TS 16949 - 5 parts 100% dimensional report
India Electrical Laboratory needed for IEC testing: tracking and erosion testing on silicone composite insulators according to IEC:61109 for 1000hrs. Creepage distance will be approximately 550mm.
China ISO Electronics Laboratory needed for ANSI AAMI shelf life testing for ECG Electrodes in accordance to ANSI/AAMI EC12:2000 samples size is 30pcs of Disposable ECG 5-ld hydrogel electrode with 100cm wire,please note that one lead wire include 5 electrodes.and our electrode with wire,so you don't need stripping and soldering.
Dubai Electrical Laboratory needed IEC Certification Testing of transformer at manufacturer factory.
Electrical Laboratory needed for Certification Testing for Partial Static Discharge on a small Torroid Transformer in the range of 3KV
USA Electrical/Mechanical Laboratory needed for testing 4kW On-Board DC-DC converter for Shock & Vibration, Temperature Cycle, Thermal Shock, Fungal Growth/Flamability, Humidity, Immersion test, Altitude, Overvoltage/Reverse voltage,withstand voltage, short/open circuit; ESD/EMC, Reliability testing
USA/Canada/South America Electrical Laboratory needed for UL Testing, Arcing testing over flexible conduit fittings as per UL 1203 Section 92. The objective of testing is to prove the insulation grade of an insulating liner that comes inside the flexible fitting. The fitting is made in stainless steel. The test is made with a 250 volts DC current which varies from 200A for 1/2" NPT fittings, to 2000A for 2" NPT fittings.
India/China ASTM Electrical Laboratory needed for ASTM Testing, inclined tracking & erosion testing as per ASTM D 2303.
Electrical Laboratory needed for testing IEC 60250 for dielectric constant and disspation factor at 1Ghz and 2GHz? Please advise what specimen(s) do you need? Price? Leadtime?
Electrical Laboratory needed for testing Numerical Protective Relay including routine test(visual inspection,mechanical operation test,accuracy and measurement test,insulation test, high voltage test)
Electrical Laboratory needed for IEC Testing copper cable compression lugs as per IEC 61238-I, Class A.
India OECD/ASTM Microbiology Laboratory needed for testing Mineral oil for bio-degradability as per OECD 310B/ASTM.
Electrical Laboratory needed for IP-41 eletronics testing electronic console for IP - 41 Protection class
Taiwan or China Optical Laboratory needed for LCD Testing, luminance measurements of LCD panels using a spectroradiometer (basic luminance meter is not good enough)
Europe Electrical Laboratory needed for electrical impedance characterization ~(0.1 Hz - 10 GHz)
ECSS or ASTM Laboratory needed to test samples/ materials for %TML and %CVCM by outgassing analysis according to ECSS- Q-ST-70-02 standard.
ASTM Packaging/Mechanical Laboratory needed for the following testing: SEQUENCE: 1 ELEMENT: A Manual Handling Distribution Simulation Hazards incurred during manual handling such as loading, unloading, dropping, throwing, stacking, sorting or palletizing. DESIGN TESTING PRACTICE FORM Delphi Electronics & Safety PKG WI FOR 651.01.02A Effective Date: March 12, 2006 2 Test Standard- ASTM D4169 (latest revision) Equipment - Lansmont drop tester model PDT-56E Conditioning - ambient Drop Height - 21 inches Drop Sequence - bottom, bottom edge, adjacent bottom edge, bottom corner, diagonally opposite corner Results: SEQUENCE: 2 ELEMENT: D Vehicle Stacking Distribution Simulation Compressive loads that occur during vehicle transport or warehousing. Test Standard- ASTM D4169 (latest revision) Equipment -Lansmont model 765K compression test sys
HK Asia FDA/ISO Packaging Laboratory needed for testing the resistibility of our products packages during Air, Sea and ground transportation Number of samples - 3
Slovenia or Hungary Physical Laboratory needed for Temperature Cycling Testing: 3 cycles in the temperature range of 0 to +70 deg.C. The cycle time shall allow a thermal tabilization after each temperature change, but not less than one-hour. The rate of the temperature change shall be 5°C per minute max.
Bangalore, India Electrical Laboratory needed to test new RJ45 connector for CAT7 cable.
India (UP) NABL Mechanical Laboratory needed for Vibration and Shock Test, Dump Heat Test, Dry Heat Test, EMC/EMI, IP 23, etc. Functional Test after each and every testing, Insulation & High Voltage, Reverse Polarity etc of Electronic Controller Card (PCB) of Brushless DC Railway Carriage Fan
Eastern USA Electrical Laboratory needed to test our 480V, 60 Hz, 100 kW Active Rectifier for its response to voltage dips and frequency shifts while both sourcing and sinking rated power.
Belgium-France SAR Testing Laboratory needed to test anti radiation mobile stickers.
Electrical laboratory needed for ASTM testing: Dielectric Constant, Dissipation @ 1GHz and 10GHz,Dielectric Strength, Vol/Surface Resistivity.
Electrical Laboratory needed to do harmonic testing (THD)of VFD (variable frequency drives)of various rating.
Electrical Laboratory needed to conduct load test on the following electrical motors details are given below :- 1. Power: 100KW/100KW/35KW. 2. Power: 100KW/100KW/40KW. Speed 1440/720/240 P, 415 V, 50Hz, 3 Phase, Frame size: 400. Duty : 60 mins rated full load, 10 mins for slow speed & 30 mins for slack rope. Foot mounted with flange at Non-driving end for brake mounting shaft at both driving and non-driving ends. IP 56, F Class, NSS II Grade.
USA Analytical Chemistry Laboratory needed for vapor pressure analysis of liquid inks.
USA Electrical Laboratory needed for testing in accordance to CCC. 1.Marking and instructions 2.Electric construction 3.Earth leakage current 4.Electric strength 5.Ground resistance 6.Dimension of plug of direct plug-in AC power adapter 7.Disturbance voltage at Mains part 8. Radiated disturbance 9. Harmonic current
Electrical Laboratory needed to do an ESD test in accordance to the ANSI C63.16 (1993) standard, Contact Discharge levels with extended level of 16KV with 96A peak.
Acoustics Laboratory need to measure the acoustic gain on HAC Enable for mobile phone for elderly in accordance to FCC Section 68.
Ontario Materials Laboratory needed for ASTM Packaging testing to ASTM D642 & D999 of modules shipped in plastic tote boxes, and need to determine if modules can be damaged during transport to our customer.
Toronto Materials Laboratory needed for ASTM Packaging testing to ASTM D642 & D999 of modules shipped in plastic tote boxes, and need to determine if modules can be damaged during transport to our customer.
NY Electronics Laboratory needed for vacuum decay testing to determine if electronic enclosure will be water tight.
Electronics Laboratory needed for IEC Testing, IEC 60754-2 - Test on Gases Evolved During Combustion of Electric Cables- Determine - Degree of Acidity of Gases Evolved During Combustion Of Materials Taken From Electric Cables - Measure pH and Conductivity.
It Is required That Section 8.1- General Method Performed on the Samples With 8.1.2 Weighted Values As The Result. $COST Turn-Around-Time 3 to 6 Components Per Cable Provide The Cost Per Cable Component. Turn-Around-Time For The Testing.
If Possible, Call Me Back Today Before 5PM (EST). Email: info@ASTB.US Tel: 212-943-3160
Thank You. Best Regards, Dr. David Hoeltzel Manager of Technical Services American Standards Testing Bureau (ASTB)- New York
Mumbai electrical laboratory needed for IEC Testing of electronic equipment as per IEC
USA Electrical Laboratory needed for UL,CSA Testing Performance and Thermal Test 600 V, 3 Phase, 60 Hz, 786 Amp, Harmonic Filter. Filtr used on VFD input. Test output required is THID to 51st harmonic, and stable temperatures at full load
Milwaukee Electrical Laboratory needed for IEC AC#, Electrical load life Testing, 16 Amps and 200 amps 500,000 operations. 3 devices Make and Break test 3 devices
China Medical Electronics Laboratory needed for ISO 8573.1 Class 5 Testing of Medical Compressor
Law Firm needs Maryland electrical laboratory for electrical testing of two residential 15 amp circuit breakers removed from a house's circuit panel
Europe Electrical Laboratory needed for NFC33-020 Performance testing of aerial Bunched cable accessories according to NFC33-020
USA Electrical Laboratory needed for current rating testing for edgecard connector, 5 amps @ operating temperature of 125 degree C.
Large Electronics Mfg needs US or Ireland Microbiology Laboratory for industrial water testing that can detect both slow and fast growing bacteria, as well as fungi with a sensitivity down to ~80cfu/100 ml. "
North America ISO 17025 Electrical Laboratory needed for Photometric Testing to EN 12966 Section 7
Malaysia Electrical Laboratory needed for CE Marking Testing to comply with EMC directive 2004/108/EC
Independent Electrical laboratory needed for RCD/ MCB for fault current and earth leakage
Large electronics mfg need IPC-TM-650 2.3.28 Ionic Chromatography testing as process qualification on modled electronics parts This test is required when starting a new assembly line, switching to a new printed circuit board supplier, changing a pcb supplier processs or materials, or moving to a new contract manufacturer. The test should be performed annually to ensure the CM has maintained the quality of work. Ionic Chromatography measures the amount of ionic contamination that is present on the surface of the printed circuit board. Ionic contamination is a concern due to the relationship between high contamination levels and failure of the printed circuit board due to electromigration. The purpose of this document is to define the data collection procedure, the recommend method of analysis, defining the specification limits of each i
West Coast USA electronics laboratory needed for lumen count on Bicycle headlights and taillights
Europe government agency needs OIML, IEC electrical laboratory for testing electricity meters
Electical Certification Laboratory needed for CB certification of electrical switches like electric switches & sockets. of all the electric switches(Sockets). Now we are planning to introduce our range into foreign electric switch market. . CE certification for sell our product in the EEA (European Economic Area) and need the CB OR ANY OTHER CERTIFIED BODY CERTIFICAION as well to sell our product in UK household market.We have the CE certification with us.Is it possible that after go for the CB testing and certification we are able to sell our product in UK & EUROPE. introduce the product in UK & EUROPE. I HAD THE CE, ISO9001 CERTIFICATION WITH US AND TESTING REPORTS AS WELL. MY MAIN ENQUIRY IS THAT IS IT POSSIBLE THAT WE ARE GO FOR THE KITEMARK & ASTA CERTIFICATION WITHOUT THE TESTING AND ONLY PAY THE THERE LICENCE FEE. PLEASE TRY T
Electronics Laboratory needed for testing an autoclave cycling product 100 plus cycles. Product is cables 5-20 pcs of 2ft lengths. autoclave cycling that uses a vacuum pulse cycle (4 cycles 150 to -0100 torr) temp cycle 0-134C for 4 min and dry time of 5 min post temp at e 200 torr.
Electrical Laboratory needed for electronics testing specifications as follows Pressure, LP2A00 Pressure transducer, jumper selectable ranges of +/-0.5", +/-1", 0-1" and 0-2" WC. Confirm these pressure ranges with the 4-20mA of the transducer. Unit powered by either 24Vac or dc. Accuracy of +/-1% Full scale output
LP2A03 Pressure transducer, jumper selectable ranges of +/-2.5", +/-5", 0-5" and 0-10" WC. Confirm these pressure ranges with the 4-20mA of the transducer. Unit powered by either 24Vac or dc. Accuracy of +/-1% Full scale output
Temperature. All below are temperature transducers having a 4-20mA output over a known temperature range, powered by 24 Vac or dc. Transmitter accuracy is specified as follows; +/0.1% of span, including linearity. (sensor not included) Details below. TE500F121A6 Application: Outside
Laboratorios de Europa necessitas para Electronica/fiabilidad Micro secciones en componente y soldadura smd
Large Electronics Manufacturer needs East Coast USA Materials Laboratory for Hardness Testing of used and unused manganese alloy metal needs to be measured. The material is 1/4" thick. Used material is believed to be shot hardened. Current testing, using a Rockwell C hardness tester, yielded unusable results. The metal needs to be tested using a more sensitive scale (Brinell?).
Asia IEC Physical Laboratory needed for testing a cast resin medium voltage insulator for Hv Frequency, Wet & Dry. Testing for impulse and power frequency and tensile strength.
India Electrical Laboratory needed for lead free alloys testing for soldering electronic components.
Western US Electrical Certification Laboratory needed for IEC ATEX EEx Testing enclosure containing electronics for EEx-d explosion proof rating
USA UN,DOT,IATA, TDG, IMO Product Safety Laboratory needed for metallurgical testing metal powder (97% Tantalum, 3% Tungsten) to determine if powder is classificed as UN 3089, Class 4.1 or as UN 3189, Class 4.2
Electronics Laboratory needed for laser compatiability testing o materials used in laser environment
India and UK Microbiology Laboratory needed for GLP microbial efficacy of few under test samples, against strains of Bacteria, Fungi, Yeast and Algae.
US A2LA, NVLAP Analytical Chemistry Laboratory need to test response of a sensor to 60-90 ppm HF in air
Electronics certification laboratory needed for electrical certification of blood glucose meters to the British Hypertension Society (BHS) protocol/and or International Protocol.
Physical Laboratory needed for NFPA Testing and ASTM Testing of electronic equipment under NFPA 130, ASTM E 162 and 662.
Puerto Electrical Laboratory needed for power transformer testing and Certification of Power Distribution transformer
Analytical Chemistry Laboratory needed for identification testing of powder used in Earthing systems for cathodic protection. This powder is mainly cementious compound consisting of high content of Carbon . If we provide a sample block of this powder or sample powder ,Can you please explain me whether you can conduct the following tests?
1) pH measurement
2) Solubility in acidic environment
3) Leaching test should be performed according to the standard EN 12457-2
4) Determination of the concentrations of constituents of interest should be performed according to EN 12506.
5) Sulphur Determination test should be performed according to ISO 4689-3:2004
6) Conductivity test
All the above tests are to be performed according
Electronics Laboratory needed for testing power transmission cables according to government standards.
New York Metropolitan Electrical/Product Safety Laboratory needed for testing LED Lightbar for Police and Emergency Response Vehicles.
A2LA Electrical laboratory needed for voltage drop testing: 80 MV MAX AT 130 AMP, 50 MV AT 80 AMP.
Chile, South America Product Safety Laboratory required for: 60335-1 Safety 60335-2-56 (Projectors & Similar)
Canada Preferred Mechanical and Enviromental Laboratories required for: 1-Mechanical shock to 270 pounds system to ANSI N42.43-2006 standard 2- Dust and moisture protection to ANSI N42.43-2006 standard
USA ANSI/IEEE C62.11 Electrical Laboratory required to test a new product that could replace HV MOV arresters-require all the tests that surge arrester receive according to ANSI/IEEE C62.11
Canada ANSI C119 Electrical Laboratory required for testing Electrical Insulating Tube, Cold Shrink, 600 Volt, 3/0 AWG, 90Deg. C, 11â?? Long (10/Pack). Cold Shrink Insulating pre-stretched tubing 11â?? for cable OD 0.62 / 0.96â?? EPR for insulating 3/0 AWG splice on secondary underground distribution cable. ANSI C119. Heat Shrink Tubing, self extin. Black cross linked polyolefin, 90 Deg Cel, 600 V., thick wall lined with adhesive/sealant. For insulating 3/0 AWG splices on secondary underground distribution cable and mech. Protection for extra flex copper grounding cable . Tubing RCVD length 30.5 CM, nominal RCVD wall thickness 3mm, min,. expanded ID 28 MM, max recovered ID 9.4 MM. ANSI C119.
Electrical Laboratory required to perform following tests based on our specifications: Rain tightness/humidity Resistance to impact Overload Dielectric withstand Operating light level Surge arrester Load
India Mil Acoustics Laboratory required for acoustic noise testing 150-170 db on component.
Destructive Laboratory required for JEDEC Standard Solder Ball Shear/Wire Bond Shear Test
EN-50131-1 Electrical Laboratory needed that is authorized and capable of performing CENELEC testing, and granting certification in the fiels of EMC, Wireless emmisions, Safety, Immunity & telephonia. Our products are Alarm Systems, wireless & wired, low powerand we need to pass EN-50131-1 Alarm Systems-Intrusion Systems and other relevantstandards for our products.
Electrical Laboratory needed for Electrical Resistance Measurement - Measure resistance and leakage current of dielectric under 100 V bias.
EASTERN USA Electrical Laboratory needed for Standard UL 1030 Dielectric Voltage - Withstand Test & Thermal Endurance Test.
Brazil Acoustics Laboratory required for Random Vibration Test: SPEC 18-2155 - item 11.1.1 / 9.1 / 11.2 - All IVECO Fluid: 18-1825-A000 / Tutsol 4000 Drawing of the Meter 011391 I weigh of the equipment + he/she asks + fluid approximately 70Kg
USA Electrical Laboratory needed for thermally situmulated discharge current - this test is for investigating electrostatic charging properties of dielectric materials.
Los Angeles Electrical Laboratory needed for EMI Testing, Temperature, Humidity, Vibration, Lighting Strike.
Electrical Laboratory needed for IEC Testing of 400ATP Feeder Pillar Panel BoardShort Circuit Test 46KV for 0.3Sec.
USA Physical Laboratory needed for IEC 60332 Fire retardant testing of different cable: 1.5mm²xsingle core stranded /flexible FR cable, 5mm²xsingle core stranded /flexible FR cable, 1.5mm²x2 core stranded /flexible FR cable
4) 2.5mm²x 2 core stranded /flexible FR cable
Utan and Idaho Electrical Laboratory needed for FCC Class A EMC Field/In-SituField testing of large outdoor electronic units
Nevafa Electrical Laboratory needed for electrical certification testing of Electrical devices LCD/LED backlit panel with cooling system. Need certification to use for public displays. UL requires too much time.
India Electronics Certification Laboratory needed for DGS&D testing of CCTV cameras, Hand Held Metal Detector, vibration sensors based alarm system, perimeter fencing protection
Analytical Chemistry Laboratory needed for Premanufacture Notice Testing: Dissociation constant, Particle size, Octanol / water partition, Henry's Law constant v. Volatilization from water vi. Volatilization from soil vii. Flammability viii. Explodability ix. Adsorption / coefficient x. Density xi. Vapor pressure If so, could I get a quote? Sample matrix is solid (powder).
Africa Electrical Laboratory needed for IEC Testing of PVC insulated stranded electronics cable against IEC 60227-3 and IEC 60227-4
Supplier of electronic cigarette eLiquid needs FDA GMP analytical chemistry laboratory for product safety testing of ingredients. We need full analysis of our liquid with emphasis on safety for human consumption and ingredients. Basically the standard testing for retail consumable products.
USA Materials Laboratory needed for ISO and DIN Testing: ISO 178; DIN 53453; ISO 527; ISO 604; VDE 030/1; IEC 216; IEC 707; ISO 62;
US Electronics Company needs chemical resistance testing of three materials to to I2, iodine.
India Lighting Manufacturer needs electrical laboratory for BIS radiofrequency disturbances test
Florida Electrical Laboratory needed for electrical Testing including coordination study /arc all gear in place. Use the information we provide to produce a coordination study/Arc flash analysis......... ASAP
Laboratory Incubator Manufacturer needs UKAS physical laboratory for testing temperature of a reagent incubators, one to hold a temperature of 15c +/- 0.5c and the other to hold the temperature of 5.5c +/- 1.0c.
Any Location SAE AS81044 close 220.127.116.11 Electrical Laboratory required for testing; Ageing in an oven (velocity of air 100-200Feet p minute), 200°C/7 days + band test + AC test 2,5kV/5min.
USA Electrical Laboratory required for testing ribbon cables. Some data that we need is 1. Impedance of the ribbon cable 2. Shielding effectiveness
Singapore ASTM F2101-07 Microbiology Laboratory needed for Bacterial Filtration efficiency Test for Computer Manufacturing.
TN (USA) Electrical Testing Laboratory needed for dielectric strength and dielectric withstand testing on ceramic electrodes for use in our gas water heating products.
USA Electronics, Consumer Products Safety Laboratory needed for testing safety of new childrens plastic toybox which contains electrical components.
Korea Physcal Laboratory needed for MIL-STD-810F Explosive Atmosphere Testing (Environmental) This explosive atmosphere test is performed to demonstrate the ability of electronic device to operate in fuel-air explosive atmospheres without causing ignition.
Texas materials laboratory needed for developmental/characterization testing ofr sodium aluminum fluoride, fluorides, Water solubility, TDS, fluoride concentration, elemental analysis, speciation, ect, to be discussed.
USA Physical Laboratory needed for Test 2 headphones to the FAA flammability specification FAA test per Title 14, Part 25
US electronics testing needed for reliability testing on semiconductor using a Aetrium Model 1164.
USA Analytical Chemistry Laboratory needed to determine the resistivity of dichlorosilane sample.
Canada materials laboratory needed for EU REACH Testing for a list of all material in our products.
Florida electrical laboratory needed for testing electrical signs, neon signs and fluorescent signs.
Microbiology laboratory needed to test an electronics module for the fungus resistance and water proofness tests against Standard RTCA DO-160D and ABD0100.This unit is a Passenger Service adapter used in the helicopter/passenger aircraft.
Electical Laboratory needs TTI-390 testing against data sheet. Includes dielectric constant, dielectric loss tangent, etc.
USA MAterials Laboratory needed to test materials compatibility and/or degradation of new materials being developed for elctrochemical sensors, especially at temperatures ~150C. Materials are polymers, metals, aqueous and nonaqueous solutions.
ISO India Electrical Laboratory needed for laboratory ISO Testing for transformers,generators,surge arrester,motors.
Electrical Laboratory needed to determine the delay of a coaxial (RG214/U) line with two reverse male TNC connectors on the ends.
Europe Electrical Laboratory needed for IEC Testing to iec 60601-2-2 standard testing for return electrodes
USA Electrical Lab needed for SAE testing for high current circuit DC breakers according to SAE J1625 standard
USA ISO Analytical Chemistry Laboratory needed for testing aqueous solutions for part per billion by weight levels of Al, As, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Ni, Na, P, Si and Zn: 1% Nitric Acid; 35% Nitric Acid; 20% Hydrochloric Acid; 21% Hydrobromic Acid; 27% Ammonia solution; Saturated Chlorite solution.
California Electrical Lab needed for 1)Insertion Loss and Return Loss testing from 0 Hz to 3 GHz for COAX cable and connectors. 2) CAT5e conformance testing for a RJ45 jack to RJ45 jack small test box
US electrical lab needed for ANSI Pre Cert engineering evaluation testing of a Watthour Meter to ANSI C12.20 Test 17 (Effects of High Voltage Line Surges), 25 (Electrical Fast Transient/Burst Test), and 27 (RF Conducted and Radiated Emissions).
Electrical lab needed for evaluationof miniature cold cathode germicidal UV bulb in a small toothbrush sanitizer. Testing for UV leakage. We can send sample to any lab is the USA.
ELECTRICAL LAB NEEDED FOR PRODUCT SAFETY TESTING A LIGHTED CD RACKMADE OF 8mm ACRYLIC THAT HANGS IN THE WALL
Electrical laboratory needed to test 5500watt hot tub heaters that have failed causing fires and we would like to have them examined in a lab including x-rays.
Electronics Microbiology laboratory needed for MIL-STD-810F Fungus Resistance Test. Equipment shall not support Fungus growth. It should be resistent to direct or indirect fungus attack.
Electrical laboratory needed for electrical & electronics meter testing & calibration
Electrical laboratory needed for equipment to be tested in all services for the electrical field or power electronics field
Environmental laboratory needed for conductivity testing and TOC testing (5-10 ppb) water analysis
Physical laboratories (1-2) needed to test our RFID chips. These 2.45 GHz chips are only .4mm square are impervious to gamma ray sterilization. Hitachi will provide the RFID readers and chips at no charge.
Electrical laboratory needed for Testing cables of rated voltage 6Kv(Um=7.2kV) up to 30kV (Um=36 kV) and of rated voltage 30kV(Um=36 kV) UP TO 150kV(Um=170kv)(AC Dielectric withstand , PD TEST and metallic sheath test according to IEC , BS Standards IEC60502-2 , IEC 60840
Analytical Chemistry Laboratory for Pesticide chemical susceptibility testing of electronic box per DO-160
Mechanical laboratory needed for Voltage and watertightness test 3. Installation test at low temerature 4.Climatic ageing test 5.Corrosion test 6.Electric ageing test 7.
Electrical laboratory needed for electrical ageing test 2. Climatic ageing test 3. Corrosion test 4. Installation test at low tem
Clinical Laboratory needed for product safety testing od electronics products. Three different tests are needed: 1. Live blood analyses of a person before and after wearing our product 2. Laboratory tests of human blood cells (2.1.) expose the cells (red and white cells) to cell phones and laptops (to expose to the electromagnetic radiation coming off from these) and then the photos of the cells will be taken and some important biological indicators will be measured (2.2) after that expose the cells to our product andand then the photos of the cells will be taken and some important biological indicators will be measured. 3. The possiblity of this test needs to be discussed with the labortaory associate. A test where the white blood cells are fighting against bacteria or viruses...
Electrical Laboratory needed for IEC or BS Electrical Short Circuit and Tensile Strength Testing: Cleat Type Impact Resistance Resistance to Electro Mechanical Force Temperature for Permanent Application Needle Flame Test Lateral Load Test Axial Movement Test SHORT CIRCUIT TEST
Electrical laboatory needed for IEC Testing for Dielectric Constant IEC 60250, Surface resistance IEC 60093, Dielectric strength (1 mm) IEC 60243, CTI IEC 60112, Arc resistance ASTM D495-61, Thermal Expansion VDE 0304/T,1, UL 94 V0 Flame testing