Ford Sensor Testing


Laboratory Test Request Description

MULTIPLE TESTING
Environmental Simulation Laboratory for the following Ford Sensors Testing:
2 test required:

1. Salt spray, FORD CETP 00.00-L-467 --- 20pzs
2. Pressure, Temperature and vibration cycling ---- 20pzs
*****Salt spray test******

1. Measure the impedance of each of the sensors according to the settings in the table below.
2. Connect harnesses, tubing and caps and place sensors vertically inside the Spray Chamber.
3. Test for 12 weeks, according to standard CETP 00.00-L-467.
4. At the end of the test, open the chamber and let it rest at room temperature for 48 hours.
5. Visually confirm that there is no intrusion of liquid and salts inside the connector and harnesses.
6. Take a photograph of the before (chamber-mounted sensors) and after each of the sensors.
7. Carry out the Impedance measurement again once the Salt spray test is finished, according to the table below. (There should be no impedance changes greater than 10% vs. initial condition)



******Pressure, Temperature and vibration cycling******


1. Connect DUTs to manifolds and harnesses as shown in the image below. Take t photos of the equipment used and set up. Use a thermocouple to monitor the chamber temperature.
2. Use the test profile shown in the table below. Repeat 14 times.
3. Use Mobil Gargoyle Artic Oil 155 (part number 9985257) and mix with 1% fluorescent liquid.
4. Monitor for liquid leaks under UV light.



INFORMATION

Number: 22-00046

Industry: Automotive and Vehicles



Interested in learning more about this
Automotive and Vehicles Laboratory Test Request?


Unlock more information about this
Laboratory Test Request


Other automotive and vehicles laboratory services.


Other Automotive and Vehicles testing, analysis, scientific research and development, inspection, certification, engineering, failure investigation, and product development needs include :

  • Full-Vehicle Testing
  • Vehicle Environmental Simulation Testing
  • Systems Testing
  • Safety Testing
  • Performance Testing
  • Fuel Testing
  • Engines Emissions Testing
  • Heavy Duty Diesel Engine (HDDE) Testing
  • Heavy Duty (HDDE) In-Use Emissions Testing
  • Small Engine Emissions Testing
  • Pressurized Gas Analysis Testing
  • Durability Testing
  • Hydrodynamic Seal Testing
  • Gear Oil Property Testing
  • Evaporative Emission Testing
  • Vehicle Fuel System Testing
  • Cloud Intensity Testing
  • Channel Point Testing
  • Corrosion Protection Testing
  • Swelling of Synthetic Rubber Testing
  • Elemental Analysis Testing
  • Filterability Testing
  • Foaming Testing
  • Viscosity Testing
  • Volatility Testing
  • Gear Screening Testing
  • Road Stimulator Testing
  • Rapid Cycle Testing
  • Pump ability Testing
  • Pour Point Testing
  • Fuel Emissions Studies Testing
  • Fuel Efficiency Studies Testing
  • Crash Testing
  • Rams bottom Carbon Testing
  • Engine Deposit Testing
  • Wear Characterization Testing
  • Fuels System Testing
  • Vehicle Engine Deposit and Wear Evaluation Testing
  • Automotive Electrical Testing
  • Automotive Fluids Testing
  • Battery Testing
  • Corrosion Testing
  • Durability Testing
  • Evaporative Emission Testing
  • Fuel System Testing
  • Hose Testing
  • Helium Leak Testing
  • Magnetic Particle Inspection Permeation Testing
  • Portable Fuel Container Testing
  • Pump Durability Testing
  • Vibration Testing
  • Tensile Testing
  • Thermal Shock Testing
  • Shock Vibration Testing
  • NDT - Eddy Current Test (ET) Testing
  • Testing

Learn more about automotive and vehicles testing and research

Need Automotive and Vehicles Testing or Scientific Research?

Save time and money searching. Simply, submit a Automotive and Vehicles request to find the laboratories or lab suppliers that best meet your needs.

Submit Laboratory Request

Test Request: 22-00076

Contract Laboratory needed for high speed tensile testing with 10m/s velocity view


Test Request: 21-03379

MULTIPLE TESTS MULTIPLE PRODUCTS Automotive Laboratory needed for auto parts testing services. view


Test Request: 21-03355

Automotive Laboratory neee for DIN Testing of air brake tube to Din 73378 standard Polyamide tubing for motor vehicles... view