Save time and money searching! Find a Lab for all your laboratory testing and scientific research.
Gain new business by registering your laboratory.
Call us 24/7 1-855-377-6821 or send us an email.
Contract Laboratory has received the following Trains, Railroads and Railways Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Trains, Railroads and Railways Laboratories to perform their Trains, Railroads and Railways Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Trains, Railroads and Railways laboratory that would like more information on these Trains, Railroads and Railways projects, please visit our registration page or call toll us free 1-855-377-6821.
Electrical laboratory needed for SAE compliance testing of optical warning devices used on authorized emergency, maintenance, and service vehicles to SAE J845 Class 1 . Recommended practice providing design guidelines, test procedures, and performance requirements for 360 degree optical warning devices and selective coverage defined as any light that provides greater coverage then 40 degrees left-to-right but less than 360 degrees. Intended for authorized emergency, maintenance and service vehicles. Lighting tested from 5 degrees upward to 5 degrees downward.
Laboratory needed for validation testing projects on Locomotive Radiators and CACs.
1. Thermal Cycling:
Full size radiator testing, which is approximately 1000 Kg. Low and high temperature water will be required at 98 degree C and at 4 degree C. Air at high pressure shall be applied above the water. Cycles are 250000.
2. Pressure Cycling:
Full size radiator testing, which is approximately 1000 Kg. low and high temperature liquid will be used. High pressure air will be required at 60 psi with cycles of 250000.
3. Shaker Table:
Full size radiator testing. Water will be required to circulate at 40 psig pressure.
4. Highly Accelerated Life Test:
This is the process of testing product by subjecting stress, strain, temperature, pressure etc.. in excess of its normal service parameters to uncover the faults and potential modes of failure in short period of time.
5. Flow Balance Test:
This test is related to CFD Analysis.
Phsyical Laboratory needed for fatigue and endurance testing of a rubber to metal bonded silent block that to be tested for endurance as below:
Radial load : 1800 ? 3500kg
Torsional : 25 ? 30kg.m
Cardanic : 25 ? 35kg.m
At 2 ? 3Hz frequency for 1million cycles. All three forces are to be applied simultaneously .
The product : Rubber to metal bonded silent block
Total length : 196mm
Dia : 115mm
Pharmaceutical Laboratory needed for Residual Moisture Content analysis (e.g. Karl-Fisher analysis ) on lyophilized cake. All excipients in the formulation safely handled under BL 1 conditions. Fast Turn Around Times a must. Laboratory should be in the contiguous United States.
Bioanalytical Laboratory needed for Vitamin detection on Fetal Bovine Serum. Following is a list of vitamins and detectable units:
Vitamin B-12 pg/mL
Folic Acid ng/mL
Vitamin B-6 ng/mL
Thiamin B-1 ng/mL
Vitamin H Biotin pg/mL
Riboflavin B2 ng/mL
Vitamin A Retinol ng/mL
Vitamin C ng/mL
Microbiology Laboratory needed for microbial analysis SB 3112. The test material consisted of only the bacterial spores at a count of 55 x 107 cfu/ml. The tests were run in compliance with the following protocols: 1 USEPA FIFRA;GLP Standards 40 CFR 160 2 USEPA TSCA 40 CFR 792 3 Org. Economic Coop. and Dev. Principles of GLP, Annex 2, C(97)186 4 Japan Ministry of Ag, Forestry & Fisheries, Notification No. 59 Noshan 3850, Director-General of Agricultural Prod. Bureau, 10 Aug 84
Preclinical toxicology laboratory needed for Cytotoxicity studies: MEM Elution Sample Amount: 120 cm2 or 4 grams Irritation: Intracutaneous Reactivity (ISO) (w/2 extracts) Sample Amount: 240 cm2 or 8 grams Sensitization: Magnusson-Kligman (w/2 extracts) Sample Amount 600 cm2 or 32 grams (6 samples minimum) Sensitization: Local Lymph Node Assay: Sample Amount 400 cm2 or 20 grams