Incoming Pipes and Piping Laboratory Test Requests

Contract Laboratory has received the following Pipes and Piping Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Pipes and Piping Laboratories to perform their Pipes and Piping Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Pipes and Piping laboratory that would like more information on these Pipes and Piping projects, please visit our registration page or call toll us free 1-855-377-6821.

Below are our 50 most recent Pipes and Piping laboratory test requests. Please log in to see more.

17-01149

Pipes and Piping

Environmental toxicology laboratory needed for eco-toxicity testing on a pipe liner to be used in culverts in California.

Closed

17-00855

Pipes and Piping

Materials laboratory needed for confirmatory testing of jointing materials for sewer drains to DIN 4062, Cold processable plastic jointing materials for sewerdrains - Jointing materials for prefabricated parts of concrete, requirements, testing and processing

Closed

17-00790

Pipes and Piping

URGENT TESTING Laboratory needed for corrosion testing of metals to ISO 6509 on faucet shanks. ISO 6509-2:2017 specifies assessment criteria and provides guidance related to the corrosion type dezincification for the selection of copper alloys with a mass fraction of zinc >15 %, exposed to fresh, saline, or drinking water. The assessment criteria are based on the exposure tests detailed in ISO 6509

Closed

17-00761

Pipes and Piping

Construction materials laboratory needed for plastIcs testing for identification of additives in plastic pipes

Closed

17-00229

Pipes and Piping

LONG TERM. TESTING Petroleum laboratory needed for ISO and ASME Testing: of composite reinforcement to ASME PCC2/ISO 24817Petroleum, petrochemical and natural gas industries -- Composite repairs for pipework -- Qualification and design, installation, testing and inspection, .

Closed

16-02410

Pipes and Piping

Plumbing product developer in North America needs a closet flange (toilet flange) tested for CSA181.1 or ASTM d2661 or the UL corresponding certification.

Closed

16-02364

Pipes and Piping

Metal Fittings company needs microbiology laboratory for biocidial efficacy testing of product surface testing according to EN ISO 22196 and TS EN 15457 standards. We are a fittings company. Our base material is brass. We plate it with first nickel and then chrome. We apply a biocide on chrome layer.

Closed

16-02337

Pipes and Piping

FDA 175.300 and ISO 17025 accredited laboratory needed to test polymeric coating samples for repeat use with food contact, in order to use it to line food processing tanks and pipes.

Closed

16-02025

Pipes and Piping

Laboratory needed for quality control testing of the piping pressure of a piping steel lining

Closed

16-01952

Pipes and Piping

Laboratory needed for ASTM Testing of aggregates used in oil pipeline operations to the following standards ASTM:Cement:ASTM C150 ? Standard specification for Portland cement Aggregates:ASTM ?294, ?295 - Standard Guide for Petrographic Examination of Aggregates for Concrete ASTM C33 - Standard Specification for Concrete Aggregates ASTM C637 -Standard Specification for Aggregates for Radiation-Shielding ConcreteWater:ASTM C1602 - Standard Specification for Mixing Water used in the Production of Hydraulic Cement Concrete.Steel wire:ASTM A82- Standard Specification for Steel Wire, Plain for Concrete ReinforcementEN 10080 ? Steel for the Reinforcement of Concrete. Weldable Reinforcing Steel. General (Option)

Closed

16-01945

Pipes and Piping

Laboratory needed for study on the compatibility of slotted HDPE pipe (for horizontal wells) through a groundwater contaminant plume over time and with variable temperature while injecting steam. The product is multi-phased, consisting of jet fuel, trichloroethylene and stoddard solvent.

Closed

16-01808

Pipes and Piping

Shipping company needs laboratory for hose bend testing of 6 hoses that need doing bending test according to EN1765 standard. Electrically discontinuous Hydrostatic tested, Vacuum tested. Oil Suction and Discharge Hose hose id:12 ID x 30' OAL working pressure Meets BS1435 EN1765,type S15 standard 150# RF Weld Neck Flange on end 1 and 150# lap Joint Floating Flange on end 2 assembly weight:1130 LBS

Closed

16-00580

Pipes and Piping

Fittings company needs India analytical chemistry laboratory for raw material testing: Spectro (Chemical Analysis,) Micro, Mechanical,sand testing( No-Bake and Green sand) and in-coming raw materials testing etc.

Closed

16-00484

Pipes and Piping

Canada Laboratory needed for HDPE Plastic Pipe Testing to American Association of State Highway and Transportation Officials, AASHTO designations: M252 and M294
Plastic Pipes (HDPE)
All tests needed

Closed

16-00452

Pipes and Piping

India Physical laboratory needed for joint testing to test double universal joint for following test conditions
1) Functional Test
2) Double Torque test
3) Fatigue Test.
Test parameter will shared later once you confirm the testing capability for above mentioned tests.

Closed

16-00104

Pipes and Piping

Large piping company needs East Coast North America materials laboratory for ASTM Testing of six o-ring elastomer samples for DMA analysis to measure Glass Transition Temperature (tg values) following ASTM E 1640. Basically I need to dynamically compress the samples at starting temperature of -70 C with 1 hz frequency up to 60 C with 2 c/min heating rate.

Closed

15-02030

Pipes and Piping

Materials Laboratory needed for ASTM Testing of porous pipes to ASTM D638
Tensile Test, Elongations test
Fluid friction coefficient test and
Consistency factor (Cv) test

Closed

15-01931

Pipes and Piping

Contract Lab needed for radioactivity Testing of NORM contaminated piping Need levels of lead 210. Verify Radium 226 is not present

Closed

15-01896

Pipes and Piping

Materials Laboratory needed for ASTM Testing of porous pipes to ASTM D638
Tensile Test, Elongations test
Fluid friction coefficient test and
Consistency factor (Cv) test

Closed

15-01313

Pipes and Piping

Asia Laboratory needed for solvent testing to determine the type of chemical (i.e. acid) to be used and the associated concentration for softening and/or dissolving the calcium carbonate debris (we have a sample, of limited amounts ? approximately 100g) found in a natural gas pipeline, at the fastest time, without less (or any) harm to the pipeline.

We have short-listed the type of chemicals to:-

a) Acetic Acid
b) Formic Acid (together with citric acid or hydrochloric acid)

However, we are open to suggestions of other chemical types that can get the job done, while meeting the above requirements.

We need a quotation as well for below chemical:

1) Acetic Acid ? 3200 litres (3.36 tonnes)

Closed

15-01186

Pipes and Piping

Middle East Mechanical Laboratory needed for pipes testing: test the UPVC pipes according to DIN 8061-8062

Closed

15-00689

Pipes and Piping

Materials Laboratory needed for ISO plastic piping testing to ISO 4437:2007 we would like to perform following test on our pipe manufactured with PE100 material, kindly send us testing charges. Sr. no. Characteristic Unit Requirement Test parameter Test method Table 2 Characteristic of PE compound - Tested in pipe form 1) Resistance to gas constituents h ? 20 80°C 2MPa ISO 4437:07 Annex A 2) resistance to rapid crack propagation (RCP) S4 test (e ? 15min) bar Pc ? 1.5 x MOP with Pc = 3.6 xPcs4 + 2.6 (in bar) 0°C ISO 13477 3) Resistance to slow crack growth h ? 500 80°C 8.0 bar 80°C 9.2 bar ISO 13479 4) Resistance to weathering (non black) -- After weathering E ? 3.5 GJ/m² ISO 16871 Hydrostatic strength of pipe 80°C; ? 1000h ISO 1167 1 & 2 Elongation at break of pipe ? 350% ISO 6259 1& 3 De-cohesion of an electrofusion joint - percentage brittle failure 23°C; ?33.3% ISO 13954,ISO 11413 jointing condition 1 ISO 8085-3 Expecting your quick response.

Closed

15-00581

Pipes and Piping

Bergen County New Jersey physical laboratory needed for tensile strength testing of T shaped weld sample with 1" OD chromoly pipe that is .120" thick. Required tensile strength to break the pipe is calculated to be ~60,000 pounds (~100,000psi).

Closed

15-00060

Pipes and Piping

South Korea Mechanical Laboratory needed for ASME, ASTM, and NACE Mechanical testing of pipe to A522 Type 1.
We will also need to have NACE testing to MR0175.

Is KTR the only recognized lab in South Korea?

Closed

14-01502

Pipes and Piping

Materials laboratory needed to test UPVC fittings for ISO 1452-2 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure

Closed

14-01198

Pipes and Piping

Texas Laboratory needed for Lubricity Testing for O&G Pipe on Pipes. We have a customer who is wanting us to run an independent lubricity test on our Pipe on Pipe product used in Coiled Tubing vs. what they are currently using.

We typically use the below method but are open to better methods.

Method: Each lubricant is tested on the OFI Lubricity Tester. The lubricants were mixed with tap water at a loading of 0.25%, 1.5%, and 3%. The lubricity tester was set to 60 RPM (rotations per minute), and 150 inch-pounds of torque applied to the test block and test ring. The test ran for 5 minutes, and the torque reading of motor was recorded at the end of the 5 minutes. The percent torque reduction is calculated off the motor torque reading of the tap water being the blank value.

% Torque Reduction = Blank ? Lubricant Torque /
(Blank) ? 100

Closed

14-01057

Pipes and Piping

India Materials Laboratory needed for ASTM Testing: Polyester Pipes Testing ( ASTM D2992 )

Closed

14-01010

Pipes and Piping

India or Middle East Mechanical Laboratory needed for mechanical testing of PQR coupon as per below details, PQR Coupon size:- 6? SCH XXS SMLS PIPE PIPE MATERIAL :- API 5L X52 APPLICABLE STANDARDS:- QP-STD R-006 rev-1 , API1104 Test Required: 1. Tensile test:- transverse tensile test as per API1104 2. Macro Examination:- Two Pieces as per QP-STD-R-006 page 15 of 36 ( attached for your reference) 3. Charpy V notch impact test to BS EN 10045:- Three sample sets for three positions as per as per QP-STD-R-006 page 15 of 36 4. CTOD Test to BS 7448: Two sets of sample at three positions as per as per QP-STD-R-006 page 16 of 36 5. All ?weld Tensile Test to BS 876 as per as per QP-STD-R-006 page 15 of 36: Two specimens

Closed

14-00928

Pipes and Piping

UK, USA or Canada Electrical laboratory needed for ISO Testing: electrical conductivity testing to iso 8031:2009

Closed

14-00437

Pipes and Piping

Asia mechanical laboratory needed for SSC Testing. Steel pipe testing to NACE MR0175 for Sulfide stress cracking NACE MR 0175. 250 jts DRL HFRW pipe API 5L X52

Closed

Submit Pipes and Piping Testing Requests for Pipes and Piping testing and Pipes and Piping Scientific Research