Save time and money searching! Find a Lab for all your laboratory testing and scientific research.
Gain new business by registering your laboratory.
Call us 24/7 1-855-377-6821 or send us an email.
Contract Laboratory has received the following Oil, Petroleum and Gasoline Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Oil, Petroleum and Gasoline Laboratories to perform their Oil, Petroleum and Gasoline Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Oil, Petroleum and Gasoline laboratory that would like more information on these Oil, Petroleum and Gasoline projects, please visit our registration page or call toll us free 1-855-377-6821.
USA materials laboratory needed for Fluid compatibility testing of elastomeric gasket material against a specific grade of kerosene to Exxon Mobil Global Practice 06-05-01:?The Vendor shall either verify that the gasket and glue material are compatible with the specified fluids, including chemical cleaning fluids, or submit proof that verification was performed in the past. In either case, the verification shall be performed by the execution of the following two tests:a) An immersion test to measure gasket swelling, hardness, and susceptibility to chemical attack. The test shall be conducted at the design temperature, and a piece of the specified gasket shall be bonded by the specified adhesive to a piece of the specified plate. The minimum duration of this test shall be 15 days. The gasket hardness change shall not exceed 10 IRHD (International Rubber Hardness Degree), and the volume change shall not be more than 10 percent.b) A compression set test taken on a gasket section compressed to the operational dimension at the upper working temperature of the elastomers. The test shall be done over a 15-day period with compression set measurement taken over 10 cycles. The pass/fail compression is 2 percent. These requirements may be waived if Vendor has at least two years of successful operating experience involving the same gasket, the same adhesive, the same process fluids and conditions, and the same gasket supplier.?
Canada ISO bioanalytical laboratory needed forbioanalytical research study for Evaluation of the effect of crude oil contaminants as in-vitro endocrine disruptor and cell proliferation
This research will evaluates the potential endocrine disruptor activity of substances by measuring whether and to what extent a substance induces cell proliferation via estrogen receptor (ER), androgen receptor (AR) (PR) dependent pathways. This research is aimed at screening of test samples to quantify functional activities, either agonist or antagonist, that they may exert against the human androgen receptor and estrogen (ER?) estrogen (ER?).
We shall assay for the following:
1. Agonist dose-response of the AR Reporter Assay
2. Antagonist dose-response of the AR reporter Assay
3. Human ER? and ER? Agonist assays
4. Human ER? antagonist
5. Human ER? antagonist Assay
the statistical analysis shall be carried out as outline below.
Average relative light units (RLU) and corresponding standard deviation (SD) values will be determined for each model concentration (n ? 6). Signal-to-background (S/B) and Z? values will be calculated using Hill?s equation as described by Zhang, et al. (1999a). Non-linear regression and regression analysis, inhibitory concentration (IC50) as well as (Ki) and effective concentration (EC50) analysis will be performed using GraphPad Prism version 6 software. Low percentage coefficient of variation (% CV), high S/B and Z scores will confirm the robust performance of this Assay.
Oil Laboratory for crude oil testing on following:
Asphaltenes ASTM D6560;
Flash point ASTM D56:
Total sulfur, mercaptanes, H2S - UOP 163;
Total nitrogen ASTM D4629;
Bromine number ASTM D1159;
Heat of cumbustion ASTM D240;
Ashes - ASTM D482;
Metals - ASTM D5708, D5863, IP-501;
Chlorides - ASTM D4929, UOP 779, UOP 588;
Atmospheric and vacuum distillation D2892, D5236, D86, D1160;
In addition to that we need GC or GC-MS testing of light petroleum distillate.
Number of samples of crude oil right now could be 15-25 per month, petroleum distillate - 5-8 per month.
Please respond with quotations for any tests you may do for us, and please indicate time around and a sample size required.
USA or South America Laoratory needed for petrochemical testing: 1- isotopes ( total crude, saturates, aromatics ) 460 samples
2- analysis of extended diamantoids ( QEDA ) 96 samples
3- Analysis of bio markers with double spectrometry of masses ( AGC-MS-MS) 90 samples
4- IRGC-MS (CSIA-B) of isolated bio markers ( hop and and strange fracts) 90 samples
5- IRGC-MS (CSIA-D) of isolated diamondoids for oil samples plus:
Tomografía de nucleos.
Fotografia Visible y UV.
18.000 to 50k feet of nucleos
USA Oil Laboratory needed for R &D Testing: Research on Automotive Transmission Fluid ( ATF and any kind of ATF)If we put into the engine ( transmission fluid replace motor oil ) would harm the engines when we run the vehicles about 1-3 weeks . (we can use anykind of ATF for test )
Pharmaceutical Laboratory needed for Residual Moisture Content analysis (e.g. Karl-Fisher analysis ) on lyophilized cake. All excipients in the formulation safely handled under BL 1 conditions. Fast Turn Around Times a must. Laboratory should be in the contiguous United States.
Bioanalytical Laboratory needed for Vitamin detection on Fetal Bovine Serum. Following is a list of vitamins and detectable units:
Vitamin B-12 pg/mL
Folic Acid ng/mL
Vitamin B-6 ng/mL
Thiamin B-1 ng/mL
Vitamin H Biotin pg/mL
Riboflavin B2 ng/mL
Vitamin A Retinol ng/mL
Vitamin C ng/mL
Microbiology Laboratory needed for microbial analysis SB 3112. The test material consisted of only the bacterial spores at a count of 55 x 107 cfu/ml. The tests were run in compliance with the following protocols: 1 USEPA FIFRA;GLP Standards 40 CFR 160 2 USEPA TSCA 40 CFR 792 3 Org. Economic Coop. and Dev. Principles of GLP, Annex 2, C(97)186 4 Japan Ministry of Ag, Forestry & Fisheries, Notification No. 59 Noshan 3850, Director-General of Agricultural Prod. Bureau, 10 Aug 84
Preclinical toxicology laboratory needed for Cytotoxicity studies: MEM Elution Sample Amount: 120 cm2 or 4 grams Irritation: Intracutaneous Reactivity (ISO) (w/2 extracts) Sample Amount: 240 cm2 or 8 grams Sensitization: Magnusson-Kligman (w/2 extracts) Sample Amount 600 cm2 or 32 grams (6 samples minimum) Sensitization: Local Lymph Node Assay: Sample Amount 400 cm2 or 20 grams