Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Aerospace, Aviation and Aeronautical Laboratories to perform their Aerospace, Aviation and Aeronautical Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Aerospace, Aviation and Aeronautical laboratory that would like more information on these Aerospace, Aviation and Aeronautical projects, please visit Register Laboratories or call toll free 1-855-377-6821.
Electrical laboratory needed for SAE compliance testing of optical warning devices used on authorized emergency, maintenance, and service vehicles to SAE J845 Class 1 . Recommended practice providing design guidelines, test procedures, and performance requirements for 360 degree optical warning devices and selective coverage defined as any light that provides greater coverage then 40 degrees left-to-right but less than 360 degrees. Intended for authorized emergency, maintenance and service vehicles. Lighting tested from 5 degrees upward to 5 degrees downward.
Large aerospace company needs laboratory for SAE fuel system testing to 3 SAE Standards: SAE J2260, Non-metallic Fuel System Tubing with One or More Layers, SAE J2044 Quick Connect Coupling Specification for Liquid Fuel and Vapor/Emissions Systems and SAE J2045, Performance Requirements for Fuel System Tubing Assemblies
Laboratory needed for multiple tests on Oil Cooling System including crash, vibration, contamination, fire, oil leakage, thermal cycling, etc:
1. Temperature & latitude test as per DO 160 Section 4 Category -B3.
2. Temperature Variation test as per DO 160 D Section 5 Category-A.
3. Fluid Suceptability test as per DO 160 D Section 11 Category-F.
4. Humidity test as per DO 160 D Section 6 Category-C.
5. Fungus test as per DO 160 D Section 13 Category-F.
6. Salt Spray test as per DO 160 D Section 14 Category-S.
7. Water Proofness test as per DO 160 D Section 10 Category-S.
8. Icing test as per DO 160 D Section 24.
9. Operation shocks & crash safety test as per DO 160 D Section 7 Helicopter Category.
10. Constant Acceleration test test as per MIL-STD-810 Method 513.5.
11. Vibration test as per DO 160 D Sec
Physical Laboratory needed for flammability pre-testing of carbon fibre samples to CS 25.853 Flammability Requirements for Aircraft Seat Cushions Appendix F, Part I, (a)(1)(ii) (i.e. 12sec vertical burn with 305mm x 70mm samples). The objective is to try 2 or 3 different materials to assist material selection and build up some confidence before testing at the lab required by our customer.
Aerospace company needs materials laboratory for investigation study of delamination problem with decor laminating application.by coupled TGA-MS (Thermalgravimetric Analysis and Mass Spectrometry) to detect if offgassing occurs. We often see delamination or air bubbles popping in the interface between decor film and surface of honeycomb sandwich panel. We would like to know if there offgassing of film affecting the strength of adhesive causing delamination/air bubbles. (note: air are entrapped in honeycomb sandwich panels. thus offgassing might occurs when the air escapes from the core to the surface and is brought contact with the adhesive)
LONG TERM TESTING Analytical Chemistry Laboratory needed for periodically quality control testing silica gel prior to procurement of large quantities to strict quality standards. Material : SILICAL ? SORBEAD ?R? Parameters: 1. Chemical composition 2. Shape 3. Color 4. Bead size 5. Pore diameter 6. Pore volume 7. Specific surface area 8. Bulk density 9. Specific Heat 10. Attrition Loss 11. Expected life 12. Crushing Strength 13. Pressure drop 14. Achieved dew point 15. Static Adsorption ar 10%,20%,20%60%,80% RH 16. pH value 17. Reactivation/Regeneration Temperature 18. Water Resistant
Aerospace laboratories needed for Fastener tension and shear testing per National Aerospace Standard (Metric) NASM 1312-8 and NASM 1312-13
FDA GMP Food Laboratory needed for food contact surface testing of NSF61 approved coating for potable water tanks, a customer wants to coat the inside of a small taker tank onboard an aircraft but the end user also wanted to know if the coating complys with FDA food contact, nor sure it is 175.105,300 or 177 etc. Need a time frame and costs for this type of testing.
India laboratory needed for fuel testing of airline turbine fuel refuelled one year back to confirm suitability for reuse in aircrafts / helicopters.
Europe laboratory needed for aircraft battery testing to RTCA DO-160 standard, Environmental Conditions and Test Procedures for Airborne Equipment.
Aeronautical company needs laboratory for suface roughness testing on tube. Tube sample: 3.5 OD and 2.25ID Surface Roughness Test
Southeast Asia Laboratory needed for RTCA/DO-160G Testing of a WiFi entertainment distribution system for aircraft installation.Capability to test DO-160 Sections 4, 5, 6, 7, 8, 9, 15, 16, 17, 18, 19, 20, 21, 22 & 25.
India laboratory for aerospace fuel testing to JET A1 the degradation of this product how can I see that through the lab test this JET A
Physical Laboratory needed for salt spray test done to Requirement standard - ASMT B117 and should be Boeing approved.
PHYSICAL LABORATORY NEEDED FOR SAE TESTING: STRENGTH TEST OF AIRPLANE CARGO NET, UNDER SAE AS 5385C, Cargo Restraint Straps - Design Criteria and Testing Methods
Physical Laboratory needed for CSMU Testing to SAE AS 8039 rev A7.2.1 impact shock7.2.2 Penetration Resistance7.2.3 Static Crush 7.2.4 Fire Test CSMU Testing, 1. UUT size A and A? - 105mm x 80mm x 55.5mm B and B? - 105mm x 80mm x 64.5mm C and C? - 105mm x 80mm x 73.5mm
Environmental Laboratory needed for rubber testing: Environmental testing of rubber products as per MIL-STD- 810G
Optical laboratory needed for window testing: transmittance of two pre-calibrated magnesium fluoride windows can be implemented. We are looking for a transmittance reduction of <2%. The test is in the UV range. magnesium fluoride window #1: 130nm to 140nm magnesium fluoride window #2: 130nm to 180nm Could you please provide an estimate for the cost of testing per window and the expected length of time the test might take.
Physical Laboratory needed for Optical transmittance Transmittance testing of quantity = 2 (1.00" OD x 0.0275" Thk Diamond windows) for 400 - 700 nm and 7500 - 14000 nm bands.
Electrical Laboratory needed for evaluation of electrical system of X-Ray Inspection Vault The vault consist of: · 4 walls and a ceiling · 2 motor driven sliding doors · An overhead crane / manipulator to move the X-Ray tube around · Safety circuits to turn prohibit the production of X-Rays if a door is opened.
Germany or European Union Mechanical Laboratory needed for steel plate testing for 90 t loading.
India aerospace textiles laboratory needed Dry Cleaning Dry Cleaning of Aircraft Fabric as per Civil aviation standard of fabric used in aircrafts.
INDIA ISO NABL OR OTHER NATIONAL /INTERNATIONAL CERTIFIED LABORATORY FOR HYDRAULIC OIL & AVIATION TURBINE FUEL SAMPLE TESTING
Southern USA Analytical Chemistry Laboratory needed for Purity Testing: GN2 and Helium Helium: MIL-PRF-27407C Type I Grade A GN2: MIL-PRF-27401F Type I Grade A ASTM F307 & ASTM F310
India aeronnautical laboratory needed for airfoil windtunnel testing: to test naca 0012h naca 4412 and naca 6430 at various angle of attack
ASIA PHYSICAL LABORATORY NEEDED FOR WIND TUNNEL TESTING OF AIRFOIL SECTION: 1/2 SCALE MODEL TESTING OPEN ENDED WIND TUNNEL
FAA Aerospace Certification laboratory need for certification testing of fasteners to FAA form 8100 or 8130 for aircraft use to pass fire safety. Needs to pass FAA regulations 25.853(a) for flammability.
Aerospace Laboratory needed for environmental testing of the air entering our paint booth downstream of filtration for traces of chemicals utilized in treating the stored water used to humidify the incoming air.
Materials Laboratory needed for DIN Testing of testing to Nylon sleeve Aerospace -DIN 65164 Non metallic braided cable sleevings - Part 2: Technical specification. standard by Deutsches Institut Fur Normung E.V.
USA laboratory needed for FDA Physical shock testing of our iPad mount for use in transport category aircraft to FAA limits stated in 14 CFR 25.561
Aerospace Laboratory needed for Hydrogen Content Testing Hydrogen pickup on titanium tubes after etching in hydrofloric acid to Lockheed spec. mp50063 rev. b method 1a.
India mechanical laboratory needed for ASTM polymer Testing DMA testing: creep, fatigue etc for polymer thin film
Asia Material Laboratory needed for Fire, Smoke, Toxicity per FAA FAR 25 FST testing on carbon fiber composite
South America Compliance Lab needed to test sample of oxygen AVIATOR?S BREATHING,GAS in order to confirm the compliment of the specification MIL-PRF-27210 :
FAA or EASA Accredited Laboratory needed for cargo tape testing to BMS specifications. Wish to get Cargo tape, used in the sealing application in Boeing Commercial Aircrafts
United States FAA recognized laboratory needed for ASTM Materials testing and environmental testing of biochemical multi-purpose general cleaner for broad aviation applications. FAA AC-43205 requires testing under 6 ASTM protocols.
United States physical chemistry laboratory needed for Magnetic Separation test on 100 pounds of Colemanite material that is less than 70 mesh in particle size
Manufacturers of consumables for the Civil Aviation Industry need India or Asia laboratory for FAA Testing. Tests as per FAA as well EASA test protocols: P-640 Carpet Mounting double face adhesive tape as per BMS specifications - 5-133C. P-205A, Glass Cloth Tape, coated with FR Acrylic adhesive as per BMS Specifications 5 -146A. Popularly known as Cargo Tape. Placards, Interior and exterior Labels and Decals
USA Materials laboratory needed for ASTM Testing. Need to test surfactant for inside and outside aircraft cleaning to ASTM 1110ASTM F 483ASTM F 519ASTM F 502ASTM F 484ASTM F 484