Contract Laboratory has received the following incoming Laboratory Test Requests which need to be fulfilled! These Laboratory Test Requests are received from a variety of sources ranging from start-up companies to large, multinational Fortune 500 corporations, international organizations, well-respected universities and government agencies that are actively seeking Independent, Third-Party Aerospace and Aeronautical Laboratories to perform their Aerospace and Aeronautical Testing, Analysis, Assays, Product Development, Scientific Research Experiments, Inspections, Certifications, and Engineering Projects. If you are a Aerospace and Aeronautical laboratory that would like more information on these Aerospace and Aeronautical projects, please visit Register Laboratories or call toll free 1-855-377-6821.
USA aerospace laboratory needed for aerospace parts testing to find out what material it is made of, it's properties, how thick it is, the finish etc. How much is testing and what is the turnaround time for results?
Mechanical Laboratory needed for ISO Brake pad and brake rotor testing Full test for our brake pads and brake rotors.
Contract Laboratory needed for SAE Testing: Run the entire SAE J2297 (A/C Leak Detection Dye) program. Our company manufactures a Fluorescent dye that we would like to have certified to the SAE J2297 standard.
Materials Laboratory needed for IP 274 Testing and ASTM Testing: Jet fuel analysis for "Electrical conductivity" and "Contaminants - Existent gums"
Materials Laboratory needed for MIL-STD Testing of sand and dust test MIL-STD-810F standard i.e. 8.9 m/s for dust and 18-29 m/s sand.
Metallurgical Laboratory needed for Metallurgy Testing: DIN microstructure testing on Titanium Fasteners manufactured to DIN 912 Hexagon socket head cap screws and DIN 963 Slotted Flat Head Countersunk. They are use in outer space. There are 6 sizes and we need 1 or 2 samples from each size to be tested and the results to be presented by photographs and confirmation on whether the fasteners comply with the customers requirement.
Hong Kong FAA Certified textile laboratory needed for FAR Testing to FAR 25.853 : Horizontal Flammability test - Fire Test to Aircraft Material (FAA Certified) Our test sample will be used for component of air craft seat. The width of rigid tape is 55 mm.
Please kindly advise sample length required for testing. Lead time for testing
Are you able to provide us the Certificate ( material used for air craft)?
Are you Certified or accredited by any international body?
Please kindly send us your quotation terms and conditions, please.
Best regards, Kanyamart
Physical Chemistry Laboratory needed for particle size testing of particle emitted from an in-house built smoke machine. We believe the particles are from .5-10 microns in size but wish to confirm.
Large Multinational Corporation needs physical laboratory for aeronautical testing: Nozzle calibration. 762 mm throat, 50kg/s
Asia physical laboratory needed for Performance testing of Aerial Bunched Cable accessories. As per French Std. NFC33020 / NFC33021 / NFC33040 / NFC33041 / NFC33042 we are manufacturer of the Aerial Bunched Cable accessories.
Canada materials laboratory needed for metal testing of bonded Aluminum Metal to Metal Peel Test of 6-12 coupons
USA aerospace physical laboratory needed for Tensile fatigue testing of Ti specimens at RT,and at temp up to 1200F.
China / Asia analytical chemistry laboratory needed for ASTM Testing to ASTM F331 Standard Test Method for Nonvolatile Residue of Solvent Extract from Aerospace Components (Using Flash Evaporator)
point test to determine acceptable dryness - In a chamber, a sample hose shall be subjected to a 5 psi [.34 bar] Nitrogen gas purge with a known dew point of -62°C to -70°C.
Texas certified physical laboratory needed for MIL-STD airline seat testing. The specifications are: MIL-S-23190 50 pounds per AS23190-1 sh 5 (note 6) Would like to know what labs are in the area for various testing including material properties testing for aluminum, steel, and plastics.
Asia mechanical laboratory needed for failure analysis / mechanical testing of 3 blade propeller of stainless steel and 1 blade sheered off, require to identify if it is an inherent defect or design flaw
Large Automotive Company needs India Physical laboratory for Environmental Conditions and Test Procedures for Airborne Equipment Testing, Icing testing as per standard RTCA/DO-160F ,Section 24.0, Category B. there are five test units.
USA, Central USA, East Coast USA, West Coast USA Mechanical Laboratory needed for STP55/005, AMS D17.2 Testing. 10 coupons (5 ea of .080 mat'l and 5 ea of .016 2024-t3)need mechanical tests and metallographic inspection
IALA Aerospace Laboratory needed for IALA certification testing of Aviation Airfield Markers & Cones. We would like to test the point of breakage, and have this documented so we can provide to our customers as part of our Sales and Support Documentation Package
USA Physical Laboratory needed for ASTM Testing to ASTM-D-2183 Test Method for Flow Properties of Adhesives.ASTM-D-2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index).20700071043 Chemical Agent Test for HD, Mustard Gas or GB, Nerve Agent. (attached)ASTM-D-1171 Test Method for Rubber Deterioration-Surface Ozone Cracking Outdoors or Chamber. (Triangular Specimens).UL94HBHorizontal Burn Test.ASTM-D-3677 Standard Test Methods for Rubber - Identification by Infrared Spectrophotometry. ASTM-D-3687 Standard Practice for Analysis of Organic Compound Vapors Collected by the Activated Charcoal Tube Adsorption Method.
Metallurgical Laboratory needed for ASTM Testing of sheet metal testing that complies with ASTM E517-00, Standard Test Method for Plastic Strain Ratio r for Sheet Metal and ASTM E646-07, Standard Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials for Aluminum and stainless steels.
Textiles Laboratory needed for fabric emission testing of E-glass fabric coated on both sides with an intumescent coating. In qualifying the fabric we are investigating the gases / vapors that are emitted once the fabric is flamed / burned. We require data on the gases and their individual concentrations.
If there's any further info you require please let me know.
India Mechanical Laboratory needed for BPPM - Boeing Plating Porosity Meter Testing - Lawrence test is a periodic test(monthly) to control cadmium plating process in which the plate porosity to hydrogen is critical
Texas materials laboratory needed for ASTM Testing: Eutectic melting testing, Clad Diffusion Testing, Tensile Testing,
Materials Laboratory needed for ASTM Testing to ASTM G85 02-A4: Corrosion tests on aeronotical parts 3 samples
Australia mechanical laboratory needed for aircraft cable terminal testing: est / examine stainless steel aircraft control cable terminals SE30 to determine extent of surface pitting (if any) and extent of intergarnular corrosion
Mechanical Laboratory needed for DIN Tecting of MIL-W-16878/4-BFE wire to the DIN EN 3475 Standards
Cyprus or Israel Oil and Petroleum Laboratory needed for Complete ASTM D1655/D7566 Table 1 and Table 3 tests for jet fuel certification
Washington or Oregon materials laboratory needed to Measure the Surface Roughness Testing (Ra) of several 3" x 13" MDF panels coated with proprietary coating. (Measure only coated side)
Analytical Laboratory needed for to test ph and concentration of fluids such as chromic acid, nitractic acid, passivation and alodine 600.
Italy or Europe physical laboratory needed for ECSS-Q_ST or NASA STD Flammability Testing on ABS and ULTEM9085 samples
India Physical Laboratory needed for vibration testing: Frequency range will be above 10 Hz and also as low as 2.5Hz
Materials Laboratory needed to test anodize samples (per MIL-A-8625) as follows: 1.Salt spray test per ASTM B 117 2.Coating weight test per ANSI/ASTM B 137 3.Abrasion resistance test per ASTM D 4060- the out-source test lab have to accredit on AC7108 for scope of analysis that sub-contractor must be either: 1.Accredited to AC7101 (MTL) 2. Accredited by a registration body recognized by MTL. 3. Accredited to AC7108/4 or AC7108 for scope of analysis and testing performed.
Analytical Chemistry Laboratory needed for testing for FAME in Jet A, JP5 and JP8 as per IP 590 HPLC ELSD
USA MIL/FAA Laboratory needed for MIL-STD testing as per MIL-PRF-27210 HAIRLINE OXYGEN BOTTLE and OXYGEN TEST REQUIRED BY FAA
Mexico ASTM/Nadcap Metallurgical/Mechanical Laboratory needed for metallography, tensile testing
India Environmental Laboratory needed for Altitude and temperature testing as per DO-160F
USA Mechanical Laboratory needed for US Dept of Defense, First Article Test Physical Load Testing-Proof test web sling to withstand static load of 18,750 lbs for 5 min, allow to rest for 24 hrs, then measure to ensure sling returns to original length.
California MIL Analytical Chemistry Laboratory needed for purity testing for nitrogen, 99.99% per MIL-PRF-27401F.
Large Aerospace Products Supplier needs USA Analytical Chemistry Laboratory to perform GC-MS of a small chain alcohol and identify all impurities.
Florida MIL Aerospace Fuels Laboratory needed for oxygen testing in accordance to MIL-PRF-27210G
Germany/UK/Italy/Spain MIL Environmental Laboratory needed for testing as per MIL-STD-810F Method 505.4 Solar Radiation & 518 Acidic Atmosphere & 515.5 Acoustic Noise Tests.
Eastern USA Metallurgical Laboratory needed for testing copper rings used in aerospace industry to determine what alloy of copper was used at time of manufacture - Made by us(Premac) in 1982. Up to 10 samples can be provided.
USA/Canada HIRF and Lightning test lab needed for RTCA DO-160 testing: RF conduced susceptibility (BCI), RF Radiated susceptibility(HIRF)Cat G PM and Lightning (LITS) (Single Stroke, Multiple Stroke & Multiple Burst)
Yuma, Arizona Analytical Chemistry Laboratory needed for testing a sample of aviation Jet A fuel for the RVP measurement.
India Aircraft/Avionics Testing Laboratory needed for HIRF testing as per RTCA DO 160E Section 20
CALIFORNIA PHYSICAL LABORATORY NEEDED FOR DPA DESTRUCTIVE TESTING IN ACCORDANCE TO MIL-STD-1580, 5 PIECES, RF TERMINATIONS, SMA INTERFACE
ELECTRICAL LABORATORY NEEDED FOR 6 TYPES OF AIRPORT RUNWAY LIGHTING TRANSFORMERS TO BE TESTED FOR FAA STANDARD AC 150/5345-47
Asia Physical Laboratory needed for BSS testing: Flammability testing, Smoke and Heat release testing as per BSS7230, BSS7238 & BSS7322
Asia Boeing approved Laboratory needed for BSS 7230 Flammability testing, Smoke test and Heat release test for composite parts used in aircrafts As per BSS7230, BSS7322 & BSS7238
Materials Laboratory needed for compatibility testing with MMH and NTO as per NASA-STD-6001 test 15 (attached pages 46-50). The materials I would like to get tested are as follows: Lubeco 905 Vitrolube NPI-1220C Braycoat 601
USA Analytical Chemistry Laboratory needed for MSEP rating when tested at the Maximum Allowable Concentration (MAC)
WestCoast USA Laboratory needed for G-Switch Activation tested in a 4KG device to meet FAA TSO C126 or ED-62 activation requirements.
Your Largo location ASTM Mechanical Laboratory needed for Short Beam Shear testing in accordance to ASTM D2344(SBS)
Analytical Chemistry Laboratory needed to perform tests on SF6 (sulfur hexafluoride gas) mixed with Nitrogen or hydrocarbon gases. Tests include dielectric properties.
East Coast USA Electrical Laboratory needed for Partial Discharge/Corona Testing -1 sample, limit - 15 pC @ 12KVA
Europe RTCA Laboratory required for testing Aviation system level HIRF & Lightning in accordance to RTCA DO-160F Section 22 XXK55RTCA DO-160F Section 23 XX3NSAE ARP5583 at System Rig Test level for Rotorcraft Severe HIRF Environment (HIRF Environment III) using Generic Transfer Function - All Aircraft with 0dB attenuation-1 system to be tested for HIRF, cable bundle lightning multiple strike multiple burst to level 5 and direct effects to level 3.
Mechanical Laboratory required for Jetfuel thrml oxidation tester, ALCOR brand bushing, insulator
Aviation Laboratory required for Jet fuel Thrml Oxidation Tester 1. Seal, Piston, reservoir, Alcor 2. Bushing, Insulator
India Environmental Laboratory needed for MIL-STD testing Hydraulic LRUs to RTCA/DO 160 E, Section 13 or as per MIL 810 F, Method 508.5.
FAA Laboratory required to perform a complete testing of a gaseous oxygen sample in accordance with the requirements of the US DoD specification MIL-PRF-27210G Type I
Canada, Def Stan 00-35 Test Procedure B Severity B, Laboratory needed to simulate flight conditions. Test chamber must be able to maintain a temperature of -40 C at a pressure equivalent to 4500m altitude, then raise temp to 3 C at site altitude while maintaining relative humidity near saturation, followed by a phase at +30 C at site altitude while maintaining relative humidity at no less than 95%.
FAA Laboratory required to perform a complete testing of a gaseous oxygen sample , per the requirements of the US DoD specification MIL-PRF-27210G Type I - ( A.B.O. ), which attends to FAA (Federal Aviation Agency). We are an MRO in Brazil. We work under the name TAP Maintenance & Engineering and we repair narrow and wide body aircrafts.
(Aerospace Fuels Laboratory, OL SA-Alc/SFTLH - Bldg 54800, 15251 Scbub Jay Street, Cape Canaveral, AFS, FL 32920.)
Bangalore Environmental Simulation Laboratory needed for Altitiude test: Cat A2: Amb temp, Altitiude A2: 15000ft, operate for 2 hrs. Cat D2: Amb temp, Altitiude D2: 50000ft, operate for 2 hrs. Decompression test 7. Amb temp, 8000 ft altitiude ( 564 mm Hg) , stabilise temp 8. in 15 secs reduce pr. to 15000 ft altitude ( 429 mm Hg), dwell for 10 min, operate 9. overpressure test -15000 ft ( 170 KPa ) pr, for 10 min, operate
Asia ASTM Mechanical Laboratory required for the following Tests: · In-Plane Tension - ASTM D3039 · In-Plane Shear - ASTM D2719 · Flexural Test - ASTM C393
India Electrical Laboratory required for ESD tests like static decay time, surface resistivity etc.
Tucson, AZ ASTM & ISO Electrical Laboratory required to do 3 axis vibe test on a battery
Nevada Oil and Petroleum Testing Laboratory needed to determine if there is JetA fuel in 100 LL Avgas
New York Metallurgical Laboratory needed for evaluation of lab results (material - forged aluminum), we are looking for a company who has alot of experience with evaulating lpi (liquid penetrate inspect) results ect. for aluminum castings.
China (near Suzhou City) Avionics Laboratory needed for DO-160 Environmental Conditions and Test Procedures for Airborne Equipment
Asia, preferable Singapore Mechanical Laboratory needed to do composite panel/coupon testing, Mechanical, Fire and Lightning(optional)test.
Laboratory required to test Lightning Strike 1 and 10 MHz Damped Sine at 4kA Pin Inject
Metropolitan NYC Metallurgical Laboratory needed for metals identification testing of metal debris that we'd like tested to see what materials it may be from; also what type of plane possibly (if it's a plane at all)
Asia or USA Materials Laboratory needed for L-P-410A or ASTMD5989 or ASTMD4066, Specific gravity & Melting point & Tensile strenght & Elongation,percent & Relative viscosity
Materials Laboratory needed for SACMA SRM 8R-94material strength properties testing: Short beam shear strength of orientated fiber-resin composites.
Test specimen size is 1.125" long x 0.25" wide x 0.040" thick.
Please note that there are special requirements under the testing spec for samples less than 0.080" thick
Mississauga ON BAERD GEN-018 2D Bombardier CTS 0002-2D Mechanical Laboratory needed for adhesive Shear test.
India Engineering Laboratory to do hydogen permeability test (LAWRENCE TESTER OR BOEING GAGE TEST) in cadmium plating solution.
Westcoast USA Analytical Chemistry Laboratory needed for GC-MS analysis for high purity gas analysis: hydrogen, argon, helium.
UK Manchester ASTM D2196-05 Analytical Chemistry Laboratory needed to do viscosity testing of de-/anti-icing fluids used in aircraft.
USA Materials Laboratory needed for Viscosity Testing of Deicing and Antiicing Fluid used in aircraft
Physical laboratory needed for testing and material selection of airplane seat in economy class for airline in China.
USA Textiles Laboratory needed for SAEJ369, FMVSS302, ASTM D461 Testing 100% Polyester Sample Size: As per requested
Melting Point (Minimum) at 482F (250C) using Differential Scanning Calorimetry (DSC) Softening Point (Minimum) at 428F (220C) using Thermomechanical Analysis (TMA) or Differential Scanning Calorimetry (DSC) Unit Weight Test at 7.0oz/yd^2 (237 g/m^2) +/- 10% Thickness Test 0.140in +/- 10% by ASTM D461
Fire Resistance according to SAEJ369 / FMVSS302 - requires certified test report
USA analytical chemistry laboratory needed for testing Glass filled Phenolic Molding Compound for moisture by using a Ohaus Moisture Balance.
OEM Aerospace Manufacturer needs metrology laboratory to outsource all metrology services for 3000 items including monitoring to performing routine calibrations, to sending them to various sources for calibration beyond our capability, repairing or sending for repair, etc. Looking to move forward in a rapid manner.
Canada Metallurgical Laboratory needed for analysis of electroplating process solutions including chrome, cadmium, anodizing, nickel,caustic cleaners, acids.
USA ISO 9001, PHYSICAL LABORATORY NEEDED TO TEST PHYSICAL DIMENSIONS OF SCREWS AND BOLTS PER OUR ISO 9001/AS9120 REQUIREMENTS
Large Automotive Manufacturer needs USA Materials Laboratory to verify chemistry & physical properties to specification provided. Material used in investment casting industry to make ceramic shell for patterns.
Microbiology laboratory needed to test an electronics module for the fungus resistance and water proofness tests against Standard RTCA DO-160D and ABD0100.This unit is a Passenger Service adapter used in the helicopter/passenger aircraft.
India Physical and Microbiology Laboratory needed for fungus resistance and water proofness testing on an electronic module, a Passenger Service adapter used in the helicopter/passenger aircraft .
Materials Lab needed for Aerospace Testing of hand tools to Aerospace Standards AS4283, AS4984
Materials lab needed for ASTM Testing for Ash Content per ASTM D4574 and Consistency per ASTM D217 for Thermal Barrier, Silicone, Aramid Filled Tape (Tacky Tape)
NDT Mechanical lab needed for ASTM testing to aerospace specs including hardness testing; flourescent penetrant inspection, magnetic particle inspection; surface temper etch inspection; conductivity testing
Analytical Chemistry Laboratory needed for testing spent aircraft de-icing fluids from various airports and define differences.
Aviation Analytical Chemistry laboratory needed for AS1197A testing an oxygen pressure regulator for an aviation emergency oxygen system.
Physical laboratory needed for reliability testing - Cycle/static/abuse testing of aircraft seats.
Analytical Chemistry and Physical Laboratory needed to test ACID/ alkaline evaluation of fabric materials to determine if corrosion to aircraft aluminum is likely and quantity/ type of flame retardent may also be needed.
FAA Mechanical Laboratory required for installation and integration testing of aircraft air management systems for certification testing.
Aerospace laboratory needed for RTCA-DO-160E Section 4 category (B 2)Section 5 category testing(B),Section 7 category (B) Section 8 category (U2/F & F1),Section 15 CategoryZ(4),Section16 CategoryZ (3) ,Section 17 category A,Section 20 category Y,Section 21 category M,Section 25 category A
Physical Laboratory needed for ASTM Air Permeability Testing in accordance with ASTM D737 on two specimens of light polyester fabric
Physical laboratory needed for ASTM Testing for Aircraft carpet testing for Cleanability testing to named American products. Backcoating Integrity to ASTM D5252-05 Tuft bind to ASTM D1335-05, BreakingForce to ASTMD2646-05 Pilling toASTM D5417-05,Edge Bind strength to BSS7313.
European physical laboratory needed for Experimental modal analysis at high level of amplitude (500 until 1000 N or more) on parts of a rocket engine with poly- excitation systems and controls. We need 100 and more measurement channels(acceleration, strain gauges). The tests must be done with the level of quality of space activities.
Aerospace manufacturer needs materials laboratory needed for testing to identify substance on aerospace components.
Mechnical Laboratory needed for MIL-STD Testing: FLOURECENT PENETRANT INSPECT PER MIL-STD-6866 TYPE I, LEVEL 3, METHOD B., BUSHING, SLEEVE MATERIAL: BERYLLLIUM COPPER PER QQ-C-530, COND HT